aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bridge, multicast-to-unicast: fix echoes on STAFelix Fietkau2015-09-181-15/+20
| | | | | | | | | | | | | | | | | | | | | | | Currently, multicast packets from an STA are sent to any according multicast listener directly through the bridge multicast-to-unicast feature. Unfortunately, so far this includes the originating STA, too, resulting in multicast packets being echo'ed back to the originating STA if it itself is a multicast listener for that group. This behaviour breaks IPv6 duplicate address detection: An IPv6 Neighbor Solicitation for IPv6 Duplicate Address Detection is being echo'ed back, resulting in the host falsely detecting an address collision, which makes the node unable to claim an IPv6 address and use IPv6 in general. Mac80211 unfortunately only prevents the echoes for us for multicast frames. For the multicast frames cast to a unicast destination we'll need to take care of excluding the originator ourselves. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Backport of r46765 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@47003 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: Fix per interface nf_call_iptables settingFelix Fietkau2015-09-181-172/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit r30917 ("kernel: bypass all netfilter hooks if the sysctls for that functionality have been disabled - eliminates the overhead of enabling CONFIG_BRIDGE_NETFILTER in the kernel config") introduced an optimization which should reduce/eliminate the overhead for traffic send over bridges on kernels compiled with CONFIG_BRIDGE_NETFILTER=y. But this optimization breaks the nf_call_iptables per bridge setting which is more fine grained than the global sysctl net.bridge.bridge-nf-call-iptables setting. A test reflecting a real world setup was created to identify if this really eliminates the overhead and if per-bridge nf_call_iptables could be used in some setups to increase the throughput. A Qualcomm Atheros QCA9558 based system with one ethernet and an ath9k wifi 3x3 in HT40 mode was used. Cables from the AP to the wifi station were used to reduce interference problems during the tests. The wlan interface was put in one bridge interface called br-wlan. This bridge usually contains some more wlan interfaces. The eth0 was put in a second bridge called br-lan. This usually contains some other privileged wlan or mesh interfaces. Routing was added between br-lan and br-wlan. Three kernels were tested: * (default) OpenWrt kernel for this device * (brfilter-global) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y * (brfilter-local) OpenWrt kernel with CONFIG_BRIDGE_NETFILTER=y and without 644-bridge_optimize_netfilter_hooks.patch The changes to the the netfilter settings of the bridge were done via: * (brfilter-global) /sbin/sysctl -w net.bridge.bridge-nf-call-iptables=1 * (brfilter-lobal) echo 1 > /sys/class/net/br-lan/bridge/nf_call_iptables and/or echo 1 > /sys/class/net/br-wan/bridge/nf_call_iptables A station connected to the wlan0 (AP) interface was used to send traffic to a PC connected via ethernet. iperf with 3 concurrent transmissions was used to generate the traffic. | kernel | br-nf-* global | nf-call* iface | download | upload | |-----------------|----------------|----------------|----------|----------| | default | 0 | - | 209 | 268 | | brfilter-global | 0 | - | 185 | 243 | | brfilter-local | 0 | - | 187 | 243 | | brfilter-local | 0 | br-lan | 157 | 226 | | brfilter-local | 0 | br-lan br-wlan | 139 | 161 | | brfilter-global | 1 | - | 136 | 162 | Download/upload results in Mibit/s It can be seen that the patch doesn't eliminate the overhead. It can also be seen that the throughput of brfilter-global and brfilter-local with disabled filtering is the roughly the same. Also the throughput for brfilter-global and brfilter-local for enabled filtering on all bridges is roughly the same. But also the brfilter-local throughput is higher when only br-lan requires the filtering. This setting would not be possible with 644-bridge_optimize_netfilter_hooks.patch applied and thus can only be compared with brfilter-global and filtering enabled for all interfaces. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> Backport of r46835 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@47002 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: bridge, multicast-to-unicast: assign src after pskb_may_pull()Felix Fietkau2015-09-181-19/+26
| | | | | | | | | | | | A call to pskb_may_pull() might reallocate skb->data. Therefore we should only assign the src-pointer after any potential reallocations. Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Backport of r46721 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@47001 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Revert "kernel: disable multicast-to-unicast translation for ipv6 neighbor ↵Felix Fietkau2015-09-181-20/+17
| | | | | | | | | | | | | | | | | | | | | | solicitation (#17625)" This reverts commit a080e8e1943156168913d0353a2e99d1151102aa. It did not fix the problem but just hid some symptom. The real issue was that IGMP/MLD report suppression was not considered for the multicast-to-unicast feature. A recent netifd which isolates IGMP/MLD reports between STAs by utilizing AP-isolation and bridge-hairpinning should have fixed this. It is perfectly fine to apply multicast-to-unicast to IPv6 Neighbor Solicitations, too (once that feature is configured correctly). Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Backport of r46720 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@47000 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: solos-pci: Increase headroom on received packetsFelix Fietkau2015-09-171-0/+54
| | | | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Backport of r46993 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46995 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: ipv6: ip6_fragment: fix headroom tests and skb leakFelix Fietkau2015-09-172-1/+102
| | | | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Backport of r46992 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46994 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86/geode: enable DMI and Geos support (fixes #20512)Felix Fietkau2015-09-171-0/+5
| | | | | | | | Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Backport of r46986 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46988 3c298f89-4303-0410-b956-a3cf2f4a3e73
* x86: fix Geode LX timekeeping (#20531)Felix Fietkau2015-09-171-0/+61
| | | | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Backport of r46985 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46987 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix chunked-io support for big flash chips (#20504)Felix Fietkau2015-09-141-3/+6
| | | | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Backport of r46904 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46905 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bcm53xx: add NAND flash chip description for Asus RT-AC87URafał Miłecki2015-09-145-4/+39
| | | | | | | | | | | This isn't that important due to different NAND driver but keeps DTS and backports consistent. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Inspired by r46892 (trunk). git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46902 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: drop some left XHCI patch for 4.0Rafał Miłecki2015-09-111-46/+0
| | | | | | | | It was accidentally added in r46094. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46849 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: kernel: update 3.18 to 3.18.21Jonas Gorski2015-09-1116-42/+36
| | | | | | | | | Changelog: * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.21 Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46847 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ipq806x: delete from CC branch; it is broken and unsupportedFelix Fietkau2015-09-1161-10913/+0
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46845 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: restore 640-bridge_no_eap_forward.patch to its original formFelix Fietkau2015-09-081-1/+1
| | | | | | | | | | | | It was corrupted in r38528. The most obvious symptom is repeated messages like this: Tue Sep 8 08:25:18 2015 kern.warn kernel: [77141.972226] br-lan: received packet on wlan0 with own address as source address Signed-off-by: Dmitry Ivanov <dima@ubnt.com> Backport of r46821 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46822 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: apply serial flash size trick to Netgear WNR1000 V3Rafał Miłecki2015-09-081-2/+3
| | | | | | | | | | It also uses different block size just like WGR614 V10. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r46810 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46812 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: add Netgear WNR1000 V3 support in the Linux arch codeRafał Miłecki2015-09-081-2/+40
| | | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r46805 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46811 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: fix devicetree corruption with some boot loaders if the caches are ↵v15.05Felix Fietkau2015-09-021-0/+18
| | | | | | | | | | not ready at boot Signed-off-by: John Crispin <blogic@openwrt.org> Backport of r46766 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46767 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: fix Linksys E1200 V2 image filenameRafał Miłecki2015-08-291-1/+1
| | | | | | | | | | Drop unwanted suffix (copy & paste mistake). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r46742 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46743 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bcm53xx: add support for Netgear R7000Rafał Miłecki2015-08-266-0/+177
| | | | | | | | Backport of r46363 r46730 r46731 r46732. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46733 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: brcm63xx: fix WAP-5813n default network configJonas Gorski2015-08-261-1/+1
| | | | | | | | | | | | | /etc/uci-defaults/02_network had a typo, making it generate the wrong network config. Closes #20407. Backport of r46727. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46728 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: mvebu: kirkwood: fix ehci-orion probe if generic-phy isn't enabledJonas Gorski2015-08-231-0/+35
| | | | | | | | | | | Properly treat -ENOSYS as no PHY, else ehci-orion won't work without generic phy support. Backport of r46711. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46712 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: brcm63xx: ensure dummy byte is set for mapped spi flash with fast readJonas Gorski2015-08-239-39/+60
| | | | | | | | | | | | | | | Some CFEs seem to misconfigure the mapped memory flash access with fast read but without a dummy byte, causing all accesses to be prefixed with 0xff. This of course breaks reading out the nvram, so do not just move back to single i/o accessors, but also ensure that the dummy byte is correctly set. Backport of r46707. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46709 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mvebu: fix cobra chainmask (backport of r46697)Imre Kaloz2015-08-211-2/+2
| | | | | | | | | | Thanks Sebastian for spotting it. Signed-off-by: Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46698 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mvebu: add support for the Linksys boot counter (backport of r46690)Imre Kaloz2015-08-192-14/+20
| | | | | | | | | | | | | | | The u-boot boot counter was never reset after a successful boot, which sometimes could make some variables become out of sync. This patch adds support for the boot counter and enables auto_recovery unconditionally. Signed-off-by: Jonas Gorski <jogo@openwrt.org> Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46691 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: kernel: update 3.18 to 3.18.20Hauke Mehrtens2015-08-1711-40/+32
| | | | | | | | | | Changelog: * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.20 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46680 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Add support for Black SwiftJohn Crispin2015-08-1710-0/+172
| | | | | | | | | | | | Add support for the Black Swift board: http://www.black-swift.com/ Took relevant parts and slightly adapted from: https://github.com/blackswift/openwrt/blob/master/bsb.patch Signed-off-by: Bruno Randolf <br1@einfach.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46674 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Enable ath10k calibration data loading for EnGenius ESR1750 and EPG500.John Crispin2015-08-171-0/+4
| | | | | | | | Kinda-backport of r46415, though this patch uses the old-style calibration data loading. Signed-off-by: Christian Beier <cb@shoutrlabs.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46673 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bcm53xx: add workaround for Netgear R8000 networkRafał Miłecki2015-08-122-1/+25
| | | | | | | | | | According to the info from NVRAM we should use port 8 for the CPU (and interface eth2). Unfortunately it doesn't work right now, so lets switch to the port 5. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46586 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: fix reading WGT634U CFE variablesRafał Miłecki2015-08-121-6/+6
| | | | | | | | | | | | We got check for nvram_len placed too early and the code never tried reading CFE variables used on WGT634U. This is a regression introduced in r45942 and reported in #20291. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Backport of r46584 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46585 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: use automatic firmware partition splitting for devolo dLAN devicesJohn Crispin2015-08-031-4/+4
| | | | | | | | Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> Backport of r46414 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46549 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Backport support for Onion OmegaJohn Crispin2015-08-039-14/+155
| | | | | | | | | | | | Backport of r46458 to CC https://onion.io/omega Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Acked-by: Boken Lin <bl@onion.io> Tested-by: Jacky Huang <huangfangcheng@163.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46548 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Fix Ticket #20153 swap radio calibration data pointers on the RE6500Felix Fietkau2015-08-021-2/+2
| | | | | | | | | | This patch fixes weak radio signal reported by nikola.georgiev Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Backport of r46545 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46546 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: fix mr3220 device profile (#19990)Felix Fietkau2015-08-011-1/+1
| | | | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> Backport of r46541 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46542 3c298f89-4303-0410-b956-a3cf2f4a3e73
* sunxi: CC: fix networking on Olimex A20 MicroZoltan HERPAI2015-07-311-1/+1
| | | | | | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46537 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mvebu: update dts files for mamba / WRT1900AC (backport of r46530)Imre Kaloz2015-07-311-2/+2
| | | | | | | | | | | Fix for default button states in WRT1900AC dts files. This prevents overlay wipe when reset is pressed. Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46531 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mvebu: fix gpio config on the WRT1200AC (backport of r46527)Imre Kaloz2015-07-311-3/+3
| | | | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46528 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: sdk: provide explicit CONFIG_MODULES kconfig symbolJo-Philipp Wich2015-07-271-0/+5
| | | | | | | | | | | | Extend the SDK Config.in file to explicitely declare a MODULES symbol with the "option modules" flag set in order to prevent a kconfig segmentation fault whenever a "depends m" dependency is encountered. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> Backport of r46514 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46515 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: swap radio calibration data pointers for DIR-860LFelix Fietkau2015-07-261-2/+2
| | | | | | | | | | Fixes low 5 GHz tx power issues Signed-off-by: Felix Fietkau <nbd@openwrt.org> Backport of r46497 git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46499 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: ar71xx: EPG5000 requires ATH79_NVRAMHauke Mehrtens2015-07-251-1/+2
| | | | | | | | | | | | | | EPG5000 uses ath79 nvram functions, but does not select it. This breaks build if no other board support enabling nvram support is selected. Closes #19952. Backport of r46190. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46494 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: kernel: update 3.18 to 3.18.19Jonas Gorski2015-07-2511-34/+28
| | | | | | | | | | | Changelog: * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.19 Backport of r46439. Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46487 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: brcm63xx: HG553 buttons supportJonas Gorski2015-07-251-0/+20
| | | | | | | | | | | This patch adds buttons support for Huawei EchoLife HG553. Backport of r46388. Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46486 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: ar71xx: add LED defaults for the EnGenius EPG5000John Crispin2015-07-241-0/+5
| | | | | | | | | | NB that wlan5g is phy0tpt and wlan2g phy1tpt. Backport of r46226. Signed-off-by: Christian Beier <cb@shoutrlabs.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46450 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: ar71xx: Fix WAN port location on EnGenius ESR1750 and EPG5000.John Crispin2015-07-241-2/+2
| | | | | | | | | | The designated blue WAN port on both devices has index 5, not 1. Backport of r46227. Signed-off-by: Christian Beier <cb@shoutrlabs.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46449 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: ar71xx: add profile and build image for EnGenius EPG5000.John Crispin2015-07-242-0/+14
| | | | | | | | Backport of r46049. Signed-off-by: Christian Beier <cb@shoutrlabs.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46448 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: ar71xx: add user-space support for EnGenius EPG5000.John Crispin2015-07-244-1/+9
| | | | | | | | Backport of r46048. Signed-off-by: Christian Beier <cb@shoutrlabs.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46447 3c298f89-4303-0410-b956-a3cf2f4a3e73
* CC: ar71xx: add kernel support for EnGenius EPG5000.John Crispin2015-07-243-0/+218
| | | | | | | | Backport of r46047. Signed-off-by: Christian Beier <cb@shoutrlabs.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46446 3c298f89-4303-0410-b956-a3cf2f4a3e73
* v3: CC : ar71xx: Backport Support for the Bitmain Antminer S3John Crispin2015-07-2410-2/+178
| | | | | | | | Backport of r46236 to CC : add support for the Bitmain Antminer S3 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46445 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add support for the devolo dLAN pro 1200+ WiFi acJohn Crispin2015-07-2411-6/+254
| | | | | | | | Backport of r46342 Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46444 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: add support for the devolo dLAN pro 500 Wireless+John Crispin2015-07-2410-6/+279
| | | | | | | | Backport of r46338 Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46442 3c298f89-4303-0410-b956-a3cf2f4a3e73
* at91: add Device Tree based board detectionFlorian Fainelli2015-07-181-3/+3
| | | | | | | | | | | Set up eth0 as LAN interface by default. Backport of r46174 Signed-off-by: Florian Fainelli <florian@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/branches/chaos_calmer@46419 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 16:23:51 +0000