aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* kernel: support "linux,rootfs" DT property for splitting rootfsRafał Miłecki2022-11-102-10/+12
| | | | | | | | | OpenWrt's support for splitting rootfs (to create an extra "rootfs_data" partition) is limited to partitions called "rootfs". Upstream kernel allows any name partition to be rootfs if it has "linux,rootfs" property set. Add split support to such partitions in OpenWrt code. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: update DTS files with the latest changesRafał Miłecki2022-11-1032-13/+4255
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq40xx: add support for GL.iNet GL-A1300Weiping Yang2022-11-094-0/+342
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2 USB: 1 x USB 3.0 port Button: 1 x Reset button Switch: 1 x Mode switch LED: 1 x Blue LED + 1 x White LED Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi (IPQ40xx) # nand erase 0 0x8000000 (IPQ40xx) # nand write 0x84000000 0 $filesize By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ath79: calibrate TL-WDR4900 v2 with nvmem-cellsEdward Chow2022-11-092-17/+24
| | | | | | | | | | | | | Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration data from the nvmem subsystem. This allows us to move the userspace caldata extraction for the pci-e ath9k supported wifi into the device-tree definition of the device. wmac's nodes are also changed over to use nvmem-cells over OpenWrt's custom mtd-cal-data property. Signed-off-by: Edward Chow <equu@openmail.cc>
* ath79: add missing clock name strings in SoC dtsiShiji Yang2022-11-095-5/+14
| | | | | | | For all SoC in the ath79 target, the PLL controller provides 3 main clocks "cpu", "ddr" and "ahb" through the input clock "ref". Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: move reference clock node to SoC dtsiShiji Yang2022-11-0925-186/+24
| | | | | | | AR7161, AR724x, AR9132 and QCA95xx only support fixed frequency external crystal oscillator, so move reference clock node to SoC dtsi files. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* mac80211: remove old legacy legacy driversFelix Fietkau2022-11-094-13/+13
| | | | | | | | | | | Get rid of drivers that are either limited to 802.11b/g or don't even support cfg80211/mac80211. Most of these are either limited to boards that we don't even support anymore because of firmware size, or were only used for custom hacks by a really small number of users in the past. Let's get rid of those to reduce the maintenance effort and the number of useless packages Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: filogic: enable maxlinear PHY support, refresh configFelix Fietkau2022-11-091-0/+1
| | | | | | Needed for the 7986 RFB1 board Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: filogic: fix mt7986a ethernet devicetree entriesFelix Fietkau2022-11-091-12/+24
| | | | | | Add all ports, rename DSA ports to start at lan1 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: drop the use of device tree overlays on mt7986a-rfb boardFelix Fietkau2022-11-094-91/+92
| | | | | | | The boot loader does not support it. Instead make NAND the default image for this board Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add mediatek soc ethernet performance improvementsFelix Fietkau2022-11-0914-8/+1422
| | | | | | | | - implement multiqueue via qdma hardware shaper to deal with ports with different speeds - implement hardware DSA untagging - add NETIF_F_ALL_TSO to reduce unnecessary segmentation Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: kernel ramoops storage for C2600/AD7200Edward Matijevic2022-11-092-2/+11
| | | | | | | | | Define the kernel crash log storage ramoops/pstore feature for C2600/AD7200 and add kmod-ramoops to default. Tested with C2600 only. Signed-off-by: Edward Matijevic <motolav@gmail.com>
* ramips: define loadaddr for U6 Lite DTBDavid Bauer2022-11-081-0/+1
| | | | | | | | | | | | | The Ubiquiti UniFi 6 Lite does not correctly align the FDT by always setting fdt_high to 0xffffffff when invoking the bootubnt command. Work around this issue by loading the DTB to a valid,aligned address, so the bootloader does not have to relocate the FDT automatically. Note: The device does read the kernel before invoking bootm on the FIT image to 0x86000000. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: backport support for "linux,rootfs" in DTRafał Miłecki2022-11-0814-94/+170
| | | | | | | | | This DT property allows marking flash partition that Linux should use as a root device. It's useful for devices that don't use U-Boot and cmdline parser for partitioning. It may be used with "fixed-partitions" or some dynamic partitioning based on flash content. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: split out mtd hack for CONFIG_FIT_PARTITION + rootfsRafał Miłecki2022-11-083-4/+20
| | | | | | | | This is some hack on top of our old hack. Use separated patch for it so it's easier to understand and actually possible to describe. We should ideally get rid of this (and we actually did with kernels 5.15+). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: gl-mt1300: downclock SPI to 50MHzMichael Lyle2022-11-071-2/+1
| | | | | | | | | | | | | | | The SPI max frequency was set to 80MHz, considerably higher than the vendor clocks it in their firmware (10MHz). Multiple users reported jffs2 corruption/instability in GitHub issue #10461. My unit has a W25Q256; datasheet specifies maximum SPI frequency for read command of 50MHz. Thanks to @DragonBlueP for suggesting to eliminate m25p,fast-read; and @MPannen1979 for identifying the problem. Fixes: #10461 Signed-off-by: Michael Lyle <mlyle@lyle.org>
* ramips: fix TP-Link RE200 v3/v4 LEDsSungbo Eo2022-11-075-11/+54
| | | | | | | | | | | | Set power LED to gpio 43 instead of 44 for v3 and v4. Set red wifi LED to gpio 40 (was assigned to `red:wifi5g`). Tested by the author of the initial v3 and v4 commit. Reported-by: Richard Fröhning <misanthropos@gmx.de> Tested-by: Richard Fröhning <misanthropos@gmx.de> Signed-off-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* sdk: use git-src-full to allow Git versioningKuan-Yi Li2022-11-061-2/+2
| | | | | | | | | | | | | $(AUTORELEASE) uses Git log to determine releases and package timestamps. Base feed is shallow cloned by default in generated SDK, resulting in an incomplete Git log and therefore different local package versions than offered upstream. This patch complements commit 7fae1e5677 by setting the base feed to use `src-git-full` to solve that. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* ath79: expand rootfs for DIR-825-B1 with unused spaceAlan Luck2022-11-061-6/+21
| | | | | | | | | | Expand currently unused flash space to roofs for DIR-825-B1 by using the same flash space as the old ar71xx big image without moving the caldata. With some testing this partition is use by the OEM firmware but if changed is regenerated which allows reverting to OEM firmware Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
* ath79: add support to TrendNet TEW-673GRUKorey Caro2022-11-064-4/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the TrendNet TEW-673GRU to ath79. This device was supported in 19.07.9 but was deprecated with ar71xx. This is mostly a copy of D-Link DIR-825 B1. Updates have been completed to enable factory.bin and sysupgrade.bin both. Code improvements to DTS file and makefile. Architecture | MIPS Vendor | Qualcomm Atheros bootloader | U-Boot System-On-Chip | AR7161 rev 2 (MIPS 24Kc V7.4) CPU/Speed | 24Kc V7.4 680 MHz Flash-Chip | Macronix MX25L6405D Flash size | 8192 KiB RAM Chip: | ProMOS V58C2256164SCI5 × 2 RAM size | 64 MiB Wireless | 2 x Atheros AR922X 2.4GHz/5.0GHz 802.11abgn Ethernet | RealTek RTL8366S Gigabit w/ port based vlan support USB | Yes 2 x 2.0 Initial Flashing Process: 1) Download 22.03 tew-673gru factory bin 2) Flash 22.03 using TrendNet GUI OpenWRT Upgrade Process 3) Download 22.03 tew-673gru sysupgrade.bin 4) Flash 22.03 using OpenWRT GUI Signed-off-by: Korey Caro <korey.caro@gmail.com>
* ramips: add support for TP-Link MR600 V2(EU)Linos Giannopoulos2022-11-054-0/+235
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MR600 V2(EU) is an LTE router that also supports 4G+ band aggregation etc. and can reportedly achieve higher bandwidth with it. - Specifications: * SoC: Mediatek MT7621DAT 880MHz * RAM: 128MB DDR3 * Flash: 16MB SPI NOR flash (GD25Q128C) * LTE Modem: Qualcomm MDM9240 * WiFi 5GHz: Mediatek MT7613BEN * WiFi 2.4GHz: Mediatek MT7603EN * Ethernet: MT7530, 4x 1000Base-T. * UART: Serial console (115200 8n1), J1(GND:3) * Buttons: Reset, WPS. * LED: Power, WAN, LTE, WiFi 2GHz and 5GHz, LAN, Signal1, Signal2, Signal3 - MAC Addresses: OEM firmware configuration: 54:af:97:xx:xx:7b : 2.4G 54:af:97:xx:xx:7a : 5G 54:af:97:xx:xx:7c : LTE 54:af:97:xx:xx:7b : LAN (label) 54:af:97:xx:xx:7c : WAN - Installation: 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to openwrt.img Configure the TFTP server to listen at 192.168.0.5/24. 3. Connect to the serial console. Attach power and interrupt the boot procedure when prompted (type `tpl`). Credentials are admin / 1234 4. Configure U-Boot for booting OpenWrt from ram $ tftpboot $ bootm 5. Transfer the OpenWrt sysupgrade image to the device. - LTE: In order to setup the wwan0 interface: 1. Add a `qmi` proto interface under `/etc/config/network`, e.g.: ``` config interface 'wwan0' option device '/dev/cdc-wdm0' option proto 'qmi' option pincode 'XXXX' option apn 'your_isp_apn' ``` 2. Add `wwan0` interface to the `wan` firewall zone 3. `/etc/init.d/network restart` Signed-off-by: Linos Giannopoulos <linosgian00@gmail.com>
* ramips: add support for SIM SIMAX1800T and Haier HAR-20S2U1Shiji Yang2022-11-057-4/+254
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SIM AX18T and Haier HAR-20S2U1 Wi-Fi6 AX1800 routers are designed based on Tenbay WR1800K. They have the same hardware circuits and u-boot. SIM AX18T has three carrier customized models: SIMAX1800M (China Mobile), SIMAX1800T (China Telecom) and SIMAX1800U (China Unicom). All of these models run the same firmware. Specifications: SOC: MT7621 + MT7905 + MT7975 ROM: 128 MiB RAM: 256 MiB LED: status *3 R/G/B Button: reset *1 + wps/mesh *1 Ethernet: lan *3 + wan *1 (10/100/1000Mbps) TTL Baudrate: 115200 TFTP Server: 192.168.1.254 TFTP IP: 192.168.1.28 or 192.168.1.160 (when envs is broken) MAC Address: use address source label 30:xx:xx:xx:xx:62 wan lan 30:xx:xx:xx:xx:65 factory.0x8004 wan 30:xx:xx:xx:xx:62 factory.0x8004 -3 wlan2g 30:xx:xx:xx:xx:64 factory.0x0004 wlan5g 32:xx:xx:xx:xx:64 factory.0x0004 set 7th bit TFTP Installation (initramfs image only & recommend): 1. Set local tftp server IP: 192.168.1.254 and NetMask: 255.255.255.0 2. Rename initramfs-kernel.bin to "factory.bin" and put it in the root directory of the tftp server. (tftpd64 is a good choice for Windows) 3. Start the TFTP server, plug in the power supply, and wait for the system to boot. 4. Backup "firmware" partition and rename it to "firmware.bin", we need it to back to stock firmware. 5. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 6. Apply sysupgrade.bin in OpenWrt LuCI. Web UI Installation: 1. Apply update by uploading initramfs-factory.bin to the web UI. 2. Use "fw_printenv" command to list envs. If "firmware_select=2" is observed then set u-boot enviroment: /# fw_setenv firmware_select 1 3. Apply squashfs-sysupgrade.bin in OpenWrt LuCI. Recovery to stock firmware: a. Upload "firmware.bin" to OpenWrt /tmp, then execute: /# mtd -r write /tmp/firmware.bin firmware b. We can also write factory image "UploadBrush-bin.img" to firmware partition to recovery. Upload image file to /tmp, then execute: /# mtd erase firmware /# mtd -r write /tmp/UploadBrush-bin.img firmware How to extract stock firmware image: Download stock firmware, then use openssl: openssl aes-256-cbc -d -salt -in [Downloaded_Firmware] \ -out "firmware.tar.tgz" -k QiLunSmartWL Signed-off-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: add support for Zbtlink ZBT-WG1602-V04Alexander Horner2022-11-054-0/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Description heavily based on commit 7e89421a7c3855d66a20350a5bf9ca4cc7a2caf9 by Sergey Ryazanov <ryazanov.s.a@gmail.com> Details I cannot confirm have been removed Completed with great help from \x on IRC. Thanks, \x! Zbtlink ZBT-WG1602-V04 is a Wi-Fi router intendend for use with WWAN (UMTS/LTE/3G/4G) modems. The router board offers a couple of miniPCIe slots with USB and SIM only and another one which is a pure miniPCIe slot as well as five Gigabit Ethernet ports (4xLAN + WAN). Specification: * SoC: MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB * Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * WLAN 2GHz: MT7603E (.11bgn, MIMO 2x2) * WLAN 5GHz: MT7662E (.11nac, MIMO 2x2) * WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios * miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus * WWAN Ants: detachable x4 * External storage: microSD (SDXC) slot * USB: 3.0 Type-A port * LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1 power indicator) * Button: 1 (reset) * UART: console (115200 baud) * Power: DC jack (12 V / 2.5 A) Additional HW information: * SoC USB port 1 is shared by internal miniPCIe slot and external Type-A USB port, USB D+/D- lines are toggled between ports using a GPIO controlled DPDT switch. Installation: The kernel image can be installed directly onto the device via a browser to 192.168.1.1 using the built in firmware recovery Web UI available. It can be accessed by pushing the reset button in, applying power and holding the reset button for approximately 10 seconds. When the kernel image has been flashed, you can access LuCI and upload the sysupgrade as normal. Signed-off-by: Alexander Horner <ahorner@programmer.net>
* ramips: add support for Youku X2Shiji Yang2022-11-054-1/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: MT7620AN + MT7612EN RAM: 128 MiB DDR2 Flash: 16 MiB (Winbond W25Q28FVFG) WLAN: 2.4G + 5G LAN: LAN ports *2 WAN: WAN port *1 USB: USB2.0 *1 SD Card: MicroSD *1 Buttons: Reset *1 LEDs: ethernet *3, system, usb, wlan2g, wlan5g MAC Address: use address source label 54:36:9b:xx:xx:ac lan lan 54:36:9b:xx:xx:ac factory.0x0028 wan 54:36:9b:xx:xx:ad factory.0x002e wlan2g 54:36:9b:xx:xx:ae factory.0x0004 wlan5g 54:36:9b:xx:xx:af factory.0x8004 Installation: 1. Apply initramfs-kernel.bin in stock firmware Web UI. 2. Install sysupgrade.bin on OpenWrt and do not retain any configuration. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ramips: improve compatibility for Youku YK-L2 and YK-L1 seriesShiji Yang2022-11-054-2/+10
| | | | | | | | | | | | | | Add UIMAGE_NAME and UIMAGE_MAGIC to allow users to directly install initramfs-kernel.bin from the stock firmware Web UI. At the same time, this change makes it possible to boot OpenWrt with the official u-boot. Notice: Since the stock firmware is based on OpenWrt and the configuration will be retained by default during the upgrade process, so we must use initramfs-kernel.bin to do a initial installation. After the system restarts, install sysupgrade.bin and do not retain any configuration. Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* kernel: further cleanup of xfrm[4|6]_mode*Martin Schiller2022-11-052-8/+0
| | | | | | | | | In my commit da5c45f4d886 ("kernel: remove handling of xfrm[4|6]_mode_* modules") I missed a few default config options and description entries. Those should be gone as well. Fixes: da5c45f4d886 ("kernel: remove handling of xfrm[4|6]_mode_* modules") Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* realtek: fix typo in debug messageLuiz Angelo Daros de Luca2022-11-051-2/+2
| | | | | | vid_end was mentioned twice. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* kernel: bump 5.15 to 5.15.77John Audia2022-11-0515-54/+53
| | | | | | | | | | | | | | | | | Manually rebased: bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch lantiq/patches-5.15/0028-NET-lantiq-various-etop-fixes.patch All other patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.153John Audia2022-11-056-27/+26
| | | | | | | | | | Manually rebased: bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch lantiq/patches-5.10/0028-NET-lantiq-various-etop-fixes.patch All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: replace mt7986 watchdog assert patch with upstreamNick Hainke2022-11-053-57/+99
| | | | | | | | Replace "920-watchdog-add-mt7986-assert.patch" with upstreamed - 920-v5.16-watchdog-mtk-add-disable_wdt_extrst-support.patch - 921-v5.19-watchdog-mtk_wdt-mt7986-Add-toprgu-reset-controller.patch Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: mt7629: add tag to upstreamed patchesNick Hainke2022-11-051-0/+0
| | | | | | The patches were upstreamed. Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: add tag for upstreamed patchesNick Hainke2022-11-053-0/+0
| | | | | | The patches were upstreamed. Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: mt7986: add tag to upstreamed patchesNick Hainke2022-11-052-0/+0
| | | | | | | The patch "210-pinctrl-mediatek-add-support-for-MT7986-SoC.patch" and "212-clk-mediatek-add-mt7986-clock-support.patch" are upstreamed. Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: mt7622: add tag to upstreamed patchesNick Hainke2022-11-052-0/+0
| | | | | | | | The patches "191-arm64-dts-mt7622-specify-the-L2-cache-topology.patch" and "192-arm64-dts-mt7622-specify-the-number-of-DMA-requests.patch" are upstreamed to 5.19. Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: filogic: disable swconfigAleksander Jan Bajkowski2022-11-051-1/+0
| | | | | | | | | | | | This subtarget supports 3 devices: * Bananapi BPi-R3 (added in a96382c1bb204698cd43e82193877c10e4b63027), * MediaTek MTK7986 rfba AP (added in cffc77ae55ed0e5b9e70417d6a1e1d280cea92cf), * MediaTek MTK7986 rfbb AP (added in cffc77ae55ed0e5b9e70417d6a1e1d280cea92cf). This subtarget supports DSA from the beginning. It looks like CONFIG_SWCONFIG was copied from another config when the subtarget was created. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* mediatek: filogic: refresh configAleksander Jan Bajkowski2022-11-051-4/+4
| | | | | | | This was done by executing these command: $ time make kernel_oldconfig CONFIG_TARGET=subtarget Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* bcm4908: backport upstream BQL support for bcm4908_enetRafał Miłecki2022-11-031-1/+4
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: Refresh generic patchesHauke Mehrtens2022-11-031-4/+4
| | | | | | | This patch was out of sync. Fixes: 1673b7dca384 ("kernel: backport fixes for MediaTek Ethernet driver") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: backport fixes for MediaTek Ethernet driverDaniel Golle2022-11-026-1/+164
| | | | | | | Backport patches from net-next which fix possible memory and resource leaks in the error codepaths of WED initialization. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: support hw flow-offloading counters on newer MediaTek SoCsDaniel Golle2022-11-021-0/+409
| | | | | | | | The packet processing engine (PPE) found in newer ARM-based MediaTek SoCs provides packet and byte counters for offloaded streams. Import pending patch reading and using those counters. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: remove obsolete patchDaniel Golle2022-11-021-24/+0
| | | | | | | | | The patch enabling hardware flow offloading support on the MT7623 SoC has been merged upstream as of Linux 5.13. Remove our local patch which wrongly got forward-ported and now actually enables hardware flow offloading for the MT2701 SoC family (unsupported in OpenWrt). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* realtek: mark clock source as continuousSander Vanheule2022-11-011-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | After replacing the R4K event timer and clock source with the new Realtek Otto timer, performance for RTL839x devices was severely impacted, as reported by Hiroshi. Research by Markus showed that after commit 4657a5301eb5 ("realtek: avoid busy waiting for RTL839x PHY read/write"), the ethernet driver could only update a phy once per timer interval, which also heavily impacted boot time. On e.g. a Zyxel GS1900-48, this added around a minute to the time to fully initialise the switch. By marking the otto clocksource as continuous, the kernel enables it to be used for high resolution timers. This allows readx_poll_timeout() to sleep for less than one system timer interval, reducing system dead time. Link: https://github.com/openwrt/openwrt/issues/11117 Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com> Cc: Markus Stockhausen <markus.stockhausen@gmx.de> Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> # Panasonic Switch-M48eG PN28480K Tested-by: Jan Hoffmann <jan@3e8.eu> # HPE 1920-8G, HPE 1920-48G
* target/realtek: use netif_receive_skb_listRosen Penev2022-11-011-1/+4
| | | | | | Small performance improvement on rx. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: consider adc_oe thermal calibration value in efuseDaniel Golle2022-10-311-1/+1
| | | | | | | | | The use of the adc_oe value stored in the efuse has been dropped in MediaTek's SDK during a recent refactorization of the temperature calculation formula. Don't ignore this offset value and again include it in raw-to-deg-celsius calculation. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for YunCore FAP690Volodymyr Puiul2022-10-315-1/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 16 MB SPI NOR - Wi-Fi: - MT7915DN + MT7905DAN: 2.4/5 GHz - Ethernet: 1x 1GiE via MT7530 - UART: J4 (115200 baud) - Pinout: [3V3] (TXD) (RXD) (GND) - Bootloader: U-Boot - Buttons: - SW1 - no label on the box, combined with led - Led: Status. RGB controlled by - GPIO 14 - green color - GPIO 15 - red color - GPIO 16 - blue color Installation: OEM firmware is based on LEDE with custom UI and support standard sysupgrade variant of firmware. However it requires "*.ubin" extension for sysupgrade file. Always select "Factory reset" switch on upgrade to OpenWRT, otherwise it will not boot. MAC addresses as verified by OEM firmware: vendor source LAN factory 0x4 (label) 5g factory 0x4 (label) 2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in 4-th byte Example label: 44:xx:xx:b7:xx:xx lan: 44:xx:xx:b7:xx:xx 2g 46:xx:xx:c7:xx:xx 5g 44:xx:xx:b7:xx:xx Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
* kernel: remove handling of xfrm[4|6]_mode_* modulesMartin Schiller2022-10-312-6/+0
| | | | | | | | | | | | | | | For kernel versions before 5.2, the required IPsec modes have to be enabled explicitly (they are built-in for newer kernels). Commit 1556ed155a9a ("kernel: mode_beet mode_transport mode_tunnel xfram modules") tried to handle this, but it does not really work. Since we don't support these kernel versions anymore and the code is also broken, let's remove it. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [Remove old generic config options too] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* at91: Remove CONFIG_PINCTRL_MCP23S08 configuration optionHauke Mehrtens2022-10-312-2/+0
| | | | | | | | The CONFIG_PINCTRL_MCP23S08 configuration option is already unset in the generic kernel configuration. Fixes: f938512af639 ("target/at91: replace gpio-mcp23s08 with pinctrl-mcp23s08-spi update config") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* Revert "at91:"Hauke Mehrtens2022-10-312-0/+2
| | | | | | | | This reverts commit 7cc6ffa1b903524fe478804fd215bb858ae8c9b7. This should have been folded in an other commit. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* at91:Hauke Mehrtens2022-10-302-2/+0
| | | | | [CONFIG_PINCTRL_MCP23S08 is already unset in generic config] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: add support for YunCore FAP640Volodymyr Puiul2022-10-303-0/+220
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It is an in-wall 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621AT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 16 MB SPI - Wi-Fi: - MT7915DN + MT7905DAN: 2.4/5 GHz - Ethernet: 5x1GiE via MT7530, 1xWAN with POE and 4xLAN - UART: J4 (115200 baud) - Pinout: [3V3] (TXD) (RXD) (GND) - Power: 802.11af/at PoE; - Bootloader: U-Boot - Buttons: - Reset - LEDs: - Status - RGB controlled by - GPIO 14 LOW - green color - GPIO 15 LOW- red color - GPIO 16 LOW - blue color - WAN - gren color, controlled by switch GPIO 12 LOW - LAN1 - gren color, controlled by switch GPIO 9 HIGH - LAN2 - gren color, controlled by switch GPIO 6 LOW - LAN3 - gren color, controlled by switch GPIO 3 LOW - LAN4 - gren color, controlled by switch GPIO 0 LOW Installation: OEM firmware is based on LEDE with custom UI and support standard sysupgrade variant of firmware. However it requires "*.ubin" extension for sysupgrade file. Always select "Factory reset" switch on upgrade to OpenWRT, otherwise router will not boot. MAC addresses with OEM firmware: vendor source lan factory 0x4 (label) 5g factory 0x4 (label) 2g label with flipped bits bit in 1-st byte and bits 5, 6, 7 in 4-th byte Example label: 44:xx:xx:b7:xx:xx lan: 44:xx:xx:b7:xx:xx 2g 46:xx:xx:c7:xx:xx 5g 44:xx:xx:b7:xx:xx Signed-off-by: Volodymyr Puiul <volodymyr.puiul@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-01 20:26:17 +0000