aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: disable cache and fabric devfreq driver to improve stabilityChristian Marangi2022-11-261-2/+2
| | | | | | | | | | | | It was tested that cache scaling currently cause instability problem. This is probably caused by a latent misconfiguration that cause the L2 cache to be sourced from the wrong source and runs at an unstable freq compared to the original QSDK fw. To improve stability while the problem is bisected, disable the devfreq drivers with minimal perf penality. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* kernel: fix mtk_eth_soc issue when using secondary GMAC on MT7621/MT7622Felix Fietkau2022-11-252-9/+5
| | | | | | | | The CDMQ ingress special tag flag needs to be set for 7986 even without DSA untag offload, otherwise tx checksum offload seems to break Fixes: 9b482ee22f3f ("kernel: add more fixes for mtk_eth_soc") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: set persistent wifi mac for bpi-r64 and bpi-r3Daniel Golle2022-11-242-0/+21
| | | | | | | Use persistent MAC address for the built-in wireless interfaces of the BPi-R64 and BPi-R3 development boards. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: remove '-fit' string from kernel filenamesDaniel Golle2022-11-241-4/+4
| | | | | | | | The type of those images is already distinguishable by the '.itb' extension, there is no need for an additional '-fit' string in the filenames. Remove it to behave more like other targets. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: remove 'nand-' string from image filenamesDaniel Golle2022-11-242-16/+16
| | | | | | | | | Only on the ipq40xx subtarget different filenames were used for NAND- based devices. This is unneeded, confusing and breaks downstream tools such as luci-app-attendedsysupgrade and auc. Remove the 'nand-' string from image filenames to fix that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* bcm27xx: sound-soc-justboom-*: fix packagesEdmunt Pienkowsky2022-11-231-12/+25
| | | | | | | | | Affected packages: sound-soc-justboom-both, sound-soc-justboom-dac and sound-soc-justboom-digi. - Add snd-soc-wm8804-i2c and/or snd-soc-pcm512x-i2c kernel modules. - Add kmod-regmap-i2c package dependency. Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
* bcm27xx: sound-soc-hifiberry-digi: fix packageEdmunt Pienkowsky2022-11-231-4/+7
| | | | | | | - Add snd-soc-wm8804-i2c kernel module, - Add kmod-regmap-i2c package dependency. Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
* bcm27xx: disable duplicate sdhost driverJohn Audia2022-11-234-8/+6
| | | | | | | | | | | | | | | | Enabling both CONFIG_MMC_BCM2835 and CONFIG_MMC_BCM2835_SDHOST causes this error in dmesg: Error: Driver 'sdhost-bcm2835' is already registered, aborting... Disabling CONFIG_MMC_BCM2835 and leaving CONFIG_MMC_BCM2835_SDHOST enabled avoids this error. Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me> [Disable driver for all subtargets, refresh configs, tweak description] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: fix regression on mt7986Felix Fietkau2022-11-231-10/+2
| | | | | | | | The CDMQ ingress special tag flag needs to be set for 7986 even without DSA untag offload, otherwise tx checksum offload seems to break Fixes: 9b482ee22f3f ("kernel: add more fixes for mtk_eth_soc") Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add WED rx support for mediatekFelix Fietkau2022-11-215-0/+3077
| | | | | | This is required for rx flow offloading on mt76 with MT7986 and MT7915 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add a locking fix for netfilter hardware flow offloadingFelix Fietkau2022-11-212-0/+78
| | | | | | | Protect the flow block cb list readers against concurrent updates Reported-by: Chad Monroe <chad.monroe@smartrg.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add more fixes for mtk_eth_socFelix Fietkau2022-11-215-5/+251
| | | | | | | | Fix corner cases in DSA offload Add refcounting fix for flow offload Fix VLAN untagging issue on MT7986 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for Keenetic KN-3010Maxim Anisimov2022-11-203-0/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Keenetic KN-3010 is a 2.4/5 Ghz band 11ac (Wi-Fi 5) router, based on MT7621DAT. Specification: - System-On-Chip: MT7621DAT - CPU/Speed: 880 MHz - Flash-Chip: Winbond w25q256 - Flash size: 32768 KiB - RAM: 128 MiB - 5x 10/100/1000 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - Wireless No1 (2T2R): MT7603E 2.4 GHz 802.11bgn - Wireless No2 (2T2R): MT7613BE 5 GHz 802.11ac - 4x LED, 2x button, 1x mode switch Notes: - The device supports dual boot mode - The firmware partitions were concatinated into one - The FN button led indicator has been reassigned as the 2.4GHz wifi indicator. Flash instruction: The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24 and tftp server. 2. Rename "openwrt-ramips-mt7621-keenetic_kn-3010-squashfs-factory.bin" to "KN-3010_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power led start blinking. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* x86: enable PINCTRL for all Intel platformXiaopo Zhang2022-11-204-26/+26
| | | | | | Enable Intel PINCTRL for all platform on both 32 bit and 64 bit target. Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
* x86/64: enable Intel PINCTRL in 64bit targetXiaopo Zhang2022-11-202-14/+16
| | | | | | | | | | | | Intel PINCTRL is not enable in the 64bit build, while it is enabled in the x86/general target, which disables the ability of controlling GPIO in the 64 bit build. This commit copies the corresponding part of x86/general config, since it is already there, so it should be fine to enable the same settings here. Signed-off-by: Xiaopo Zhang <xiaopoz@proton.me>
* ath79: fix MAC address assigment for TP-Link TL-WR740N/TL-WR741ND v4Will Moss2022-11-201-3/+2
| | | | | | | On TP-Link TL-WR740N/TL-WR741ND v4 LAN MAC address (eth1 in DTS) is main device MAC address, so do not increment it. WAN MAC is LAN MAC + 1. Signed-off-by: Will Moss <willormos@gmail.com>
* ath79: disable image building for Ubiquiti EdgeSwitch 8XPRoger Pueyo Centelles2022-11-201-0/+1
| | | | | | | | | | The downstream OpenWrt driver for the BCM53128 switch ceased to work, rendering the 8 LAN ports of the device unusable. This commit disables image building while the problem is being solved. See issue #10374 for more details. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ath79: calibrate nand netgear wndrxxxx with nvmemEdward Chow2022-11-203-35/+24
| | | | | | | | | | | | | | | | | | | Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration data from the nvmem subsystem. This allows us to move the userspace caldata extraction for the pci-e ath9k supported wifi into the device-tree definition of the device. wmac's nodes are also changed over to use nvmem-cells over OpenWrt's custom mtd-cal-data property. The wifi mac address remains correct after these changes, because When both "mac-address" and "calibration" are defined, the effective mac address comes from the cell corresponding to "mac-address" and mac-address-increment. Test passed on my wndr3700v4 and wndr4500v3. Signed-off-by: Edward Chow <equu@openmail.cc>
* kernel: backport tso for asix driverAleksander Jan Bajkowski2022-11-182-0/+136
| | | | | | | | | | | | Performance comparison (iperf3, mtu 1500): Before: 53.9 Mbps After: 87.9 Mbps The tests were performed on a BT Home Hub 5A router. The iperf3 server was running on the router, the client on the host. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* lantiq: xway: kernel: enable SMP supportChristian Buschau2022-11-182-0/+50
| | | | | | | | | Enabled CONFIG_MIPS_MT_SMP and CONFIG_SCHED_SMT. Tested on FRITZ!Box 7330 SL, 7312 and o2 Box 4421. Signed-off-by: Christian Buschau <christian.buschau@mailbox.org> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: xway: ar9: add ICU1 (2nd core for SMP)Christian Buschau2022-11-181-2/+2
| | | | | | | Fixes leftover TODO from commit 6bf179b27004eb76df3e466bd080fc5a83ccf0dd Signed-off-by: Christian Buschau <christian.buschau@mailbox.org> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: xway: refresh kernel configChristian Buschau2022-11-182-3/+22
| | | | | | | Run of 'make kernel_oldconfig CONFIG_TARGET=subtarget' Signed-off-by: Christian Buschau <christian.buschau@mailbox.org> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ath79: calibrate all ar9344 tl-WDRxxxx with nvmemEdward Chow2022-11-184-41/+27
| | | | | | | | | | | | | | | | | | | | Driver for both soc (2.4GHz Wifi) and pci (5 GHz) now pull the calibration data from the nvmem subsystem. This allows us to move the userspace caldata extraction for the pci-e ath9k supported wifi into the device-tree definition of the device. wmac's nodes are also changed over to use nvmem-cells over OpenWrt's custom mtd-cal-data property. The wifi mac address remains correct after these changes, because When both "mac-address" and "calibration" are defined, the effective mac address comes from the cell corresponding to "mac-address" and mac-address-increment. Test passed on my tplink tl-wdr4310. Signed-off-by: Edward Chow <equu@openmail.cc>
* mediatek: mt7623: disable swconfigAleksander Jan Bajkowski2022-11-181-1/+0
| | | | | | | | | | | | | | | | The mt7623 subtarget supports 2 devices: * Bananapi BPi-R2 (added in 1f068588efddf0175e954ffc07ec8478bddd52c7, 7762c07c88980cff85ec20c12f18cd172260e9d9), * UniElec U7623-02 (added in 4def81f30f2e89eeecc6ec06e3091f1dd6b3c3d9). Both devices support DSA from the beginning, thus swconfig can be safely disabled. In the past, the subtarget mt7623 also supported the mt7623 reference board. This board originally supported swconfig, and was later converted to DSA (64175ffb7911f5fcd3907df09fdb9bfab53ee641) and then dropped (1ab81bf02d750c9a2a447dbf4fdb323921f291d7). Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* mediatek: mt7623: refresh configAleksander Jan Bajkowski2022-11-181-4/+3
| | | | | | | This was done by executing these command: $ time make kernel_oldconfig CONFIG_TARGET=subtarget Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* treewide: uniform vendor name for devoloMoritz Warning2022-11-181-2/+2
| | | | | | | The company name is lower case on the website (https://www.devolo.de) and in product names. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* treewide: uniform vendor name for ASUSMoritz Warning2022-11-166-20/+20
| | | | | | | Their own website (https://www.asus.com) always uses the upper case style name. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* mpc85xx: fix missing kernel config symbolJosef Schlehofer2022-11-161-0/+1
| | | | | | | | | | | | | While compiling OpenWrt master for Turris 1.x routers (p2020), it reported following error: Gianfar Ethernet (GIANFAR) [Y/n/m/?] y Freescale DPAA2 Ethernet Switch (FSL_DPAA2_SWITCH) [N/m/y/?] (NEW) Error in reading or end of file. Let's fix it by disabling it. Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* kernel: bump 5.10 to 5.10.155John Audia2022-11-162-7/+7
| | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.79John Audia2022-11-163-4/+4
| | | | | | | | | | All other patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/mt7621 Run-tested: bcm2711/RPi4B, ramips/mt7621 Signed-off-by: John Audia <therealgraysky@proton.me>
* cypress-nvram: consolidate NVRAM packagesKuan-Yi Li2022-11-161-1/+1
| | | | | | | NVRAM packages for the same wireless chip are consolidated into one as they contain only small text files and symlinks. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* linux-firmware: broadcom: consolidate NVRAM packagesKuan-Yi Li2022-11-161-9/+6
| | | | | | | NVRAM packages for the same wireless chip are consolidated into one as they contain only small text files and symlinks. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* cypress-nvram: disassociate from external source repoKuan-Yi Li2022-11-161-1/+1
| | | | | | | | | | | | Since all NVRAM files in external repo are now upstreamed and to lower future maintenance cost, disassociate the package from external source repo. All upstream pending NVRAM files shall be stored locally from now on. Signed-off-by: Kuan-Yi Li <kyli@abysm.org> [Remove outdated URL, add SPDX-License-Identifier] Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: add missing symbol in generic configPawel Dembicki2022-11-164-2/+2
| | | | | | | | Found during work on qoriq target. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [improve commit message, remove from target configs] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* linux-firmware: offer two versions of firmware for CYW4339Kuan-Yi Li2022-11-151-1/+1
| | | | | | | | | | | | | | | | | | | | | According to commit 6f6c2fb321, AP6335 module used in PICO-PI-IMX7D works only with firmware from `linux-firmware`. However, firmware from `cypress-firmware` suite is directly from the chip company (Infineon) and is actually newer. Instead of dropping the firmware from Infineon, create a package named `brcmfmac-firmware-4339-sdio`, and keep the Infineon version of `cypress-firmware-4339-sdio` around. This gives us devs the option to choose. Also, it means that - packages `brcmfmac-firmware-*` uniformly come from `linux-firmware` - packages `cypress-firmware-*` uniformly come from `cypress-firmware` so hopefully brings more clarity. Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* bcm27xx: switch to linux-firmware SDIO NVRAMKuan-Yi Li2022-11-151-9/+9
| | | | | | | | | Package `cypress-nvram` was added because back then the files for newer RPi models on `linux-firmware` didn't have the proper values. It is the other way around nowadays, so switch back to `linux-firmware`. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* cypress-nvram: use symlink to provide NVRAM for some RPisKuan-Yi Li2022-11-151-5/+8
| | | | | | | | | | This is to align the implementation with upstream `linux-firmware`. Some Raspberry Pi boards do not have dedicated NVRAM in `linux-firmware` source repository, their NVRAM is provided through a symbolic link to NVRAM of another board with an identical wireless design. Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
* rockchip: use LZMA FIT for kernel imageChuanhong Guo2022-11-145-8/+7
| | | | | | | | Use LZMA compressed kernel to save some space in boot partition. Fixes: #11197 Tested-by: Tianling Shen <cnsztl@immortalwrt.org> [NanoPi R2S] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: support Ruckus ZoneFlex 7025Lech Perczak2022-11-134-3/+225
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ruckus ZoneFlex 7025 is a single 2.4GHz radio 802.11n 1x1 enterprise access point with built-in Ethernet switch, in an electrical outlet form factor. Hardware highligts: - CPU: Atheros AR7240 SoC at 400 MHz - RAM: 64MB DDR2 - Flash: 16MB SPI-NOR - Wi-Fi: AR9285 built-in 2.4GHz 1x1 radio - Ethernet: single Fast Ethernet port inside the electrical enclosure, coupled with internal LSA connector for direct wiring, four external Fast Ethernet ports on the lower side of the device. - PoE: 802.3af PD input inside the electrical box. 802.3af PSE output on the LAN4 port, capable of sourcing class 0 or class 2 devices, depending on power supply capacity. - External 8P8C pass-through connectors on the back and right side of the device - Standalone 48V power input on the side, through 2/1mm micro DC barrel jack Serial console: 115200-8-N-1 on internal JP1 header. Pinout: ---------- JP1 |5|4|3|2|1| ---------- Pin 1 is near the "H1" marking. 1 - RX 2 - n/c 3 - VCC (3.3V) 4 - GND 5 - TX Installation: There are two methods of installation: - Using serial console [1] - requires some disassembly, 3.3V USB-Serial adapter, TFTP server, and removing a single T10 screw, but with much less manual steps, and is generally recommended, being safer. - Using stock firmware root shell exploit, SSH and TFTP [2]. Does not work on some rare versions of stock firmware. A more involved, and requires installing `mkenvimage` from u-boot-tools package if you choose to rebuild your own environment, but can be used without disassembly or removal from installation point, if you have the credentials. If for some reason, size of your sysupgrade image exceeds 13312kB, proceed with method [1]. For official images this is not likely to happen ever. [1] Using serial console: 0. Connect serial console to H1 header. Ensure the serial converter does not back-power the board, otherwise it will fail to boot. 1. Power-on the board. Then quickly connect serial converter to PC and hit Ctrl+C in the terminal to break boot sequence. If you're lucky, you'll enter U-boot shell. Then skip to point 3. Connection parameters are 115200-8-N-1. 2. Allow the board to boot. Press the reset button, so the board reboots into U-boot again and go back to point 1. 3. Set the "bootcmd" variable to disable the dual-boot feature of the system and ensure that uImage is loaded. This is critical step, and needs to be done only on initial installation. > setenv bootcmd "bootm 0x9f040000" > saveenv 4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed: > setenv serverip 192.168.1.2 > setenv ipaddr 192.168.1.1 > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7025-initramfs-kernel.bin > bootm 0x81000000 5. Optional, but highly recommended: back up contents of "firmware" partition: $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7025_fw1_backup.bin 6. Copy over sysupgrade image, and perform actual installation. OpenWrt shall boot from flash afterwards: $ ssh root@192.168.1.1 # sysupgrade -n openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin [2] Using stock root shell: 0. Reset the device to factory defaullts. Power-on the device and after it boots, hold the reset button near Ethernet connectors for 5 seconds. 1. Connect the device to the network. It will acquire address over DHCP, so either find its address using list of DHCP leases by looking for label MAC address, or try finding it by scanning for SSH port: $ nmap 10.42.0.0/24 -p22 From now on, we assume your computer has address 10.42.0.1 and the device has address 10.42.0.254. 2. Set up a TFTP server on your computer. We assume that TFTP server root is at /srv/tftp. 3. Obtain root shell. Connect to the device over SSH. The SSHD ond the frmware is pretty ancient and requires enabling HMAC-MD5. $ ssh 10.42.0.254 \ -o UserKnownHostsFile=/dev/null \ -o StrictHostKeyCheking=no \ -o MACs=hmac-md5 Login. User is "super", password is "sp-admin". Now execute a hidden command: Ruckus It is case-sensitive. Copy and paste the following string, including quotes. There will be no output on the console for that. ";/bin/sh;" Hit "enter". The AP will respond with: grrrr OK Now execute another hidden command: !v54! At "What's your chow?" prompt just hit "enter". Congratulations, you should now be dropped to Busybox shell with root permissions. 4. Optional, but highly recommended: backup the flash contents before installation. At your PC ensure the device can write the firmware over TFTP: $ sudo touch /srv/tftp/ruckus_zf7025_firmware{1,2}.bin $ sudo chmod 666 /srv/tftp/ruckus_zf7025_firmware{1,2}.bin Locate partitions for primary and secondary firmware image. NEVER blindly copy over MTD nodes, because MTD indices change depending on the currently active firmware, and all partitions are writable! # grep rcks_wlan /proc/mtd Copy over both images using TFTP, this will be useful in case you'd like to return to stock FW in future. Make sure to backup both, as OpenWrt uses bot firmwre partitions for storage! # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7025_firmware1.bin -p 10.42.0.1 # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7025_firmware2.bin -p 10.42.0.1 When the command finishes, copy over the dump to a safe place for storage. $ cp /srv/tftp/ruckus_zf7025_firmware{1,2}.bin ~/ 5. Ensure the system is running from the BACKUP image, i.e. from rcks_wlan.bkup partition or "image 2". Otherwise the installation WILL fail, and you will need to access mtd0 device to write image which risks overwriting the bootloader, and so is not covered here and not supported. Switching to backup firmware can be achieved by executing a few consecutive reboots of the device, or by updating the stock firmware. The system will boot from the image it was not running from previously. Stock firmware available to update was conveniently dumped in point 4 :-) 6. Prepare U-boot environment image. Install u-boot-tools package. Alternatively, if you build your own images, OpenWrt provides mkenvimage in host staging directory as well. It is recommended to extract environment from the device, and modify it, rather then relying on defaults: $ sudo touch /srv/tftp/u-boot-env.bin $ sudo chmod 666 /srv/tftp/u-boot-env.bin On the device, find the MTD partition on which environment resides. Beware, it may change depending on currently active firmware image! # grep u-boot-env /proc/mtd Now, copy over the partition # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1 Store the stock environment in a safe place: $ cp /srv/tftp/u-boot-env.bin ~/ Extract the values from the dump: $ strings u-boot-env.bin | tee u-boot-env.txt Now clean up the debris at the end of output, you should end up with each variable defined once. After that, set the bootcmd variable like this: bootcmd=bootm 0x9f040000 You should end up with something like this: bootcmd=bootm 0x9f040000 bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init baudrate=115200 ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee mtdparts=mtdparts=ar7100-nor0:256k(u-boot),7168k(rcks_wlan.main),7168k(rcks_wlan.bkup),1280k(datafs),256k(u-boot-env) mtdids=nor0=ar7100-nor0 bootdelay=2 filesize=52e000 fileaddr=81000000 ethact=eth0 stdin=serial stdout=serial stderr=serial partition=nor0,0 mtddevnum=0 mtddevname=u-boot ipaddr=192.168.0.1 serverip=192.168.0.2 stderr=serial ethact=eth0 These are the defaults, you can use most likely just this as input to mkenvimage. Now, create environment image and copy it over to TFTP root: $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt $ sudo cp u-boot-env.bin /srv/tftp This is the same image, gzipped and base64-encoded: H4sICOLMEGMAA3UtYm9vdC1lbnYtbmV3LmJpbgDt0E1u00AUAGDfgm2XDUrTsUV/pTkFSxZoEk+o lcQJtlNaLsURwU4FikDiBN+3eDNvLL/3Zt5/+vFuud8Pq10dp3V3EV4e1uFDGBXTQeq+9HG1b/v9 NsdheP0Y5mV5U4Vw0Y1f1/3wesix/3pM/dO6v2jaZojX/bJpr6dtsUzHuktDjm//FHl4SnXdxfAS wmN4SWkMy+UYVqsx1PUYci52Q31I3dDHP5vU3ZUhXLX7LjxWN7eby+PVNNxsflfe3m8uu9Wm//xt m9rFLjXtv6fLzfEwm5fVfdhc1mlI6342Pytzldvn2dS1qfs49Tjvd3qFOm/Ta6yKdbPNffM9x5sq Ty805acL3Zfh5HTD1RDHJRT9WLGNfe6atJ2S/XE4y3LX/c6mSzZDs29P3edhmqXOz+1xF//s0y7H t3GL5nDqWT5Ui/Gii7Aoi7HQ81jrcHZY/dXkfLLiJwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAD8 xy8jb4zOAAAEAA== 7. Perform actual installation. Copy over OpenWrt sysupgrade image to TFTP root: $ sudo cp openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin /srv/tftp Now load both to the device over TFTP: # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1 # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin -g 10.42.0.1 Verify checksums of both images to ensure the transfer over TFTP was completed: # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin And compare it against source images: $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7025-squashfs-sysupgrade.bin Locate MTD partition of the primary image: # grep rcks_wlan.main /proc/mtd Now, write the images in place. Write U-boot environment last, so unit still can boot from backup image, should power failure occur during this. Replace MTD placeholders with real MTD nodes: # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd> # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd> Finally, reboot the device. The device should directly boot into OpenWrt. Look for the characteristic power LED blinking pattern. # reboot -f After unit boots, it should be available at the usual 192.168.1.1/24. Return to factory firmware: 1. Boot into OpenWrt initramfs as for initial installation. To do that without disassembly, you can write an initramfs image to the device using 'sysupgrade -F' first. 2. Unset the "bootcmd" variable: fw_setenv bootcmd "" 3. Concatenate the firmware backups, if you took them during installation using method 2: $ cat ruckus_zf7025_fw1_backup.bin ruckus_zf7025_fw2_backup.bin > ruckus_zf7025_backup.bin 3. Write factory images downloaded from manufacturer website into fwconcat0 and fwconcat1 MTD partitions, or restore backup you took before installation: # mtd write ruckus_zf7025_backup.bin /dev/mtd1 4. Reboot the system, it should load into factory firmware again. Quirks and known issues: - Flash layout is changed from the factory, to use both firmware image partitions for storage using mtd-concat, and uImage format is used to actually boot the system, which rules out the dual-boot capability. - The 2.4 GHz radio has its own EEPROM on board, not connected to CPU. - The stock firmware has dual-boot capability, which is not supported in OpenWrt by choice. It is controlled by data in the top 64kB of RAM which is unmapped, to avoid the interference in the boot process and accidental switch to the inactive image, although boot script presence in form of "bootcmd" variable should prevent this entirely. - On some versions of stock firmware, it is possible to obtain root shell, however not much is available in terms of debugging facitilies. 1. Login to the rkscli 2. Execute hidden command "Ruckus" 3. Copy and paste ";/bin/sh;" including quotes. This is required only once, the payload will be stored in writable filesystem. 4. Execute hidden command "!v54!". Press Enter leaving empty reply for "What's your chow?" prompt. 5. Busybox shell shall open. Source: https://alephsecurity.com/vulns/aleph-2019014 Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ramips: Add support for D-Link DIR-3060 A1Ivaylo Ivanov2022-11-134-0/+253
| | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7621AT Flash: Winbond W29N01HVSINA 128MB RAM: Micron MT41K128M16JT-125 256MB Ethernet: 4x 10/100/1000 Mbps WiFi1: MT7615DN 2.4GHz N 2x2:2 WiFi2: MT7615DN 5GHz AC 2x2:2 WiFi3: MT7615N 5GHz AC 4x4:4 Button: WPS, Reset Flash instructions: OpenWrt can be installed via D-Link Recovery GUI: Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable. Give it ~30 seconds, to boot the recovery mode GUI Connect your client computer to LAN1 of the device Set your client IP address manually to 192.168.0.2 / 255.255.255.0. Call the recovery page for the device at http://192.168.0.1/ Use the provided emergency web GUI to upload and flash a new firmware to the device Signed-off-by: Ivaylo Ivanov <iivailo@mail.bg>
* ramips: add support for Amped Wireless B1200EXDaniel Fuchs2022-11-137-32/+118
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is almost identical to the already supported Edimax EW-7476RP5, the only differences are: - There is no mode selection slider switch on this device - The two wireless LEDs are green instead of blue - Model name in the CSYS header is RN10 Additional changes: - Moved WiFi LEDs and the slider switch to the individual dt files - Added ieee80211-freq-limit to the mt7612e radio to properly disable 2.4GHz band on this radio Device specifications: SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS/RESET LED: - WiFi 5G (green) - WiFi 2.4G (green) - Signal Strength (green) - Power (green) - WPS (green) - LAN (green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the WPS button 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation: Upload the sysupgrade image via the default web interface Signed-off-by: Daniel Fuchs <software@sagacioussuricata.com>
* ramips: add support for Rostelecom RT-SF-1Mikhail Zhilkin2022-11-135-2/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rostelecom RT-SF-1 is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 256 MiB, Micron MT29F2G08ABAGA3W Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5xGbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1xUSB3.0 ZigBee: 3.0, EFR32 MG1B232GG Button: 2 buttons (Reset & WPS) LEDs: - 1x Status (RGB) - 1x 2.4G (blue, hardware, mt76-phy0) - 1x 5G (blue, hardware, mt76-phy1) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Remove dots from the OpenWrt factory image filename 2. Login to the router web interface 3. Update firmware using web interface with the OpenWrt factory image 4. If OpenWrt is booted, then no further steps are required. Enjoy! Otherwise (Stock firmware has booted again) proceed to the next step. 5. Update firmware using web interface with any version of the Stock firmware 6. Update firmware using web interface with the OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses ------------- +-----+------------+------------+ | use | address | example | +-----+------------+------------+ | LAN | label | *:72, *:d2 | | WAN | label + 11 | *:7d, *:dd | | 2g | label + 2 | *:74, *:d4 | | 5g | label + 3 | *:75, *:d5 | +-----+------------+------------+ The label MAC address was found in Factory 0x21000 Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: create common dtsi for Sercomm Dxx routersMikhail Zhilkin2022-11-132-225/+240
| | | | | | | | | | | This commit adds common dtsi for the following Sercomm devices with 256 MB NAND: Beeline Smartbox TURBO (Sercomm DF3) Rostelecom RT-SF-1 (Sercomm DKG) Also fixed typo ("Container" mtd name should be with a capital). Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: glinet_gl-mt300n-v2: allow to use I2C and UART1 pins as GPIOMartin Dziura2022-11-131-5/+1
| | | | | | | This is explicitly intended by the official documentation at https://docs.gl-inet.com/en/3/specification/gl-mt300n-v2/#pcb-pinout Signed-off-by: Martin Dziura <m.dziura@tum.de>
* kconfig: abort configuration on unset symbolDavid Bauer2022-11-134-48/+82
| | | | | | | | | This fixes the initial patch to cover all cases where unset symbols are handled in the code. Fixes commit eaa9c94c7574 ("generic: Kconfig: exit on unset symbol") Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: dts: remove leftover nodes after DSA conversionLech Perczak2022-11-133-29/+1
| | | | | | | | | | | | | | Remove ess-psgmii@98000, edma@c080000 and ess-switch@c000000 nodes. These nodes are not used after the DSA conversion, but were left over in a few devices added recently. ZTE MF289F is omitted on purpose, as for it, these nodes will be removed together with DSA conversion. Build tested only, as I only have MF286D from those devices. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: Convert plasmacloud,pa2200 to DSASven Eckelmann2022-11-133-7/+32
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for plasmacloud,pa2200Sven Eckelmann2022-11-132-7/+40
| | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert plasmacloud,pa1200 to DSASven Eckelmann2022-11-133-6/+33
| | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for plasmacloud,pa1200Sven Eckelmann2022-11-132-2/+31
| | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Sven Eckelmann <sven@narfation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-15 02:04:42 +0000