| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The folder `json_info_files` contains multiple JSON files which describe
created firmware images. The folder is not removed between builds as the
ImageBuilder does not use `image.mk`.
Not removing the JSON files result in a merged `profiles.json` file
containing entries for outdated or non-existing images.
This commit adds the `json_info_files/` cleanup step to the ImageBuilder
Makefile.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
| |
The patch 4a1a58a3 build, imagebuilder: Do not require libncurses-dev
was supposed to remove libncurses as a requirement for the ImageBuilder.
However as the IB=1 is only exported during building, not for checking
requirements, it did never actually work.
This commit export IB=1 to the requirement check.
Signed-off-by: Paul Spooren <mail@aparcar.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The port order displayed in LuCI is currently inverted for this
devices:
LuCI - Device
LAN1 - LAN4
LAN2 - LAN3
LAN3 - LAN2
LAN4 - LAN1
Fix it.
Strangely, the owner of a TRENDnet TEW-810DR reports that the
initial port order is correct, while both devices share the
same board and look similar from the outside. Since I cannot
investigate this without having any of the devices, this does
only touch the DIR-810L for now.
While at it, also merge in the case for zbtlink,zbt-we2026, as
the display port specified for WAN there won't have any effect
anyway.
Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
| |
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The WAN LED on DIR-810L was actually blinking on LAN1 port
activity. This has already been improved for the TEW-810DR, where
the GPIO has been set up explicitly rather than having it controlled
by the switch.
This patch also applies this setup to the DIR-810L.
In addition, the trigger in 01_leds is set up with
ucidef_set_led_switch for both devices now, so state changes should
be displayed correctly as well.
Reported-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [DIR-810L]
Tested-by: J. Scott Heppler <shep971@centurylink.net> [TEW-810DR]
|
|
|
|
|
|
|
|
|
|
|
|
| |
With several subtargets, the image/Makefile becomes crowded after a
while. Many targets have moved their device definitions to $subtarget.mk
files to have them more organized, let's do this here as well.
While at it, also move subtarget-specific build recipes.
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Many target use a repetitive if-include scheme for their subtarget
image files, though their names are consistent with the subtarget
names.
This patch removes these redundant conditions and just uses the
variable for the include where the target setup allows it.
For sunxi, this includes a trivial rename of the subtarget image
Makefiles.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Netgear WNDRMAC v1 is a hardware variant of the Netgear WNDR3700 v2
Specifications
==============
* SoC: Atheros AR7161
* RAM: 64mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v1)
Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.
After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v1.
Please use the `sysupgrade` variant for subsequent flashes.
Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3700 page on openwrt.org for details.
https://openwrt.org/toh/netgear/wndr3700#troubleshooting_and_recovery
Signed-off-by: Renaud Lepage <root@cybikbase.com>
[update DTSI include name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Netgear WNDRMAC v2 is a hardware variant of the Netgear WNDR3800
Specifications
==============
* SoC: Atheros AR7161
* RAM: 128mb
* Flash on board: 16mb
* WiFi: Atheros AR9220 (a/n), Atheros AR9223 (b/g/n)
* Ethernet: RealTek RTL8366SR (1xWAN, 4xLAN, Gigabit)
* Serial console: Yes, 115200 / 8N1 (JTAG)
* USB: 1x2.0
* Power: 12 VDC, 2.5 A
* Full specs on [openwrt.org](https://openwrt.org/toh/hwdata/netgear/netgear_wndrmac_v2)
Flash Instructions
==================
It is possible to use the OEM Upgrade page to install the `factory`
variant of the firmware.
After the initial upgrade, you will need to telnet into the router
(default IP 192.168.1.1) to install anything. You may install LuCI
this way. At this point, you will have a web interface to configure
OpenWRT on the WNDRMAC v2.
Please use the `sysupgrade` variant for subsequent flashes.
Recovery Instructions
=====================
A TFTP-based recovery flash is possible if the need arises. Please refer
to the WNDR3800 page on openwrt.org for details.
https://openwrt.org/toh/netgear/wndr3800#recovery_flash_in_failsafe_mode
Signed-off-by: Renaud Lepage <root@cybikbase.com>
[do not add device to uboot-envtools, update DTSI name]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
This renames the DTSI for Netgear WNDR devices based on ar7161 to
indicate that the file is not limited to WNDR3700 models.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
Since 01_enable_packet_steering only touches the network config,
limit the uci commit to this as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
| |
According to the manual, the amber power LED is used to indicate boot,
while the green LED is meant to indicate a running system.
While at it, also adjust the DT node names for all LEDs.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifications:
* SoC: MT7620A
* CPU: 580 MHz
* RAM: 64 MB DDR
* Flash: 8MB NOR SPI flash
* WiFi: MT7612E (5GHz) and builtin MT7620A (2.4GHz)
* LAN: 1x100M
The device is identical to the EX6130 except
for the mains socket and the hardware ID.
Installation:
The -factory images can be flashed from the
device's web interface or via nmrpflash.
Notes:
MAC addresses were set up based on the EX6130 setup.
This is based on prior work of Adam Serbinski and Mathias Buchwald.
Tested by Mathias Buchwald.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
| |
- Speed up MDIO bus access
- Improve performance on tx completion
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
Should improve performance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
It provides a significant performance boost, especially with flow offloading
enabled
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds ar71xx's GPIO setup for the 2.4GHz and 5GHz antennae
demultiplexer:
| 158 /* 2.4 GHz uses the first fixed antenna group (1, 0, 1, 0) */
| 159 ap9x_pci_setup_wmac_gpio(0, (0xf << 6), (0xa << 6));
| 160
| 161 /* 5 GHz uses the second fixed antenna group (0, 1, 1, 0) */
| 162 ap9x_pci_setup_wmac_gpio(1, (0xf << 6), (0x6 << 6));
This should restore the range and throughput of the 2.4GHz radio
on all the derived wndr3700 variants and versions with the AR7161 SoC.
A special case is the 5GHz radio. The original wndr3700(v1) will
benefit from this change. However the wndr3700v2 and later revisions
were unaffected by the missing bits, as there is no demultiplexer
present in the later designs.
This patch uses gpio-hogs within the device-tree for all
wndr3700/wndr3800/wndrmac variants.
Notes:
Based on the PCB pictures, the WNDR3700(v1) really had eight
independent antennae. Four antennae for each radio and all of
those were printed on the circut board.
The WNDR3700v2 and later have just six antennae. Four of those
are printed on the circuit board and serve the 2.4GHz radio.
Whereas the remaining two are special 5GHz Rayspan Patch Antennae
which are directly connected to the 5GHz radio.
Hannu Nyman dug pretty deep and unearthed a treasure of information
regarding the history of how these values came to be in the OpenWrt
archives: <https://dev.archive.openwrt.org/ticket/6533.html>.
Mark Mentovai came across the fixed antenna group when he was looking
into the driver:
fixed_antenna_group 1, (0, 1, 0, 1)
fixed_antenna_group 2, (0, 1, 1, 0)
fixed_antenna_group 3, (1, 0, 0, 1)
fixed_antenna_group 4, (1, 0, 1, 0)
Fixes: FS#3088
Reported-by: Luca Bensi
Reported-by: Maciej Mazur
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Debugged-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
| |
CONFIG_VLAN_8021Q was explicitely disabled in oxnas kernel config.
Don't do that, so VLANs can be used on the target.
Fixes: dcc34574ef ("oxnas: bring in new oxnas target")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fixes CVE-2020-10757 via upstream commit df4988aa1c96 ("mm: Fix mremap
not considering huge pmd devmap").
Resolved merge conflict in the following patches:
bcm27xx: 950-0128-gpiolib-Don-t-prevent-IRQ-usage-of-output-GPIOs.patch
Refreshed patches, removed upstreamed patch:
generic: 751-v5.8-net-dsa-mt7530-set-CPU-port-to-fallback-mode.patch
generic: 754-v5.7-net-dsa-mt7530-fix-roaming-from-DSA-user-ports.patch
Run tested: qemu-x86-64
Build tested: x86/64, imx6, sunxi/a53
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This partially reverts commit 5acd1ed0be0d ("ramips: mt7621: fix
Ubiquiti ER-X ports names and MAC addresses"), this change was discussed
in https://github.com/openwrt/openwrt/pull/2901#discussion_r407238452
With commit 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names
and MAC addresses"), all the ports were put into the LAN bridge, with
the argument that the OEM firmware does not have a WAN port enabled. In
the default OEM setup, all of the ports except eth0 are dead and eth0 is
set to a static IP address without providing DHCP services when
connected. It is only after the wizard has been run that eth0 becomes
the WAN port and all the rest of the ports belong to LAN with DHCP
enabled.
Having all of the ports set to the LAN bridge does not mirror the default
OEM setup. To accomplish that, then only eth0 would be in the LAN bridge.
But this is not the expected behaviour of OpenWrt.
Therefore this proposal to set eth0 to WAN and eth1-N to LAN provides
the expected behaviour expected from OpenWrt, maintains the current
documentation as up-to-date, and does not require the user to manually
detach eth0 from the LAN bridge, create the WAN(6) interface(s), and set
eth0 to the WAN(6) interface(s).
Fixes: 5acd1ed0be0d ("ramips: mt7621: fix Ubiquiti ER-X ports names and MAC addresses")
Signed-off-by: Perry Melange <isprotejesvalkata@gmail.com>
[commit subject and description tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
| |
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
| |
BCM6328 boot selection fix has been upstreamed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Sercomm H500-s is an xDSL dual band wireless router based on Broadcom
BCM63167 SoC.
Hardware:
SoC: Broadcom BCM63167
CPU: BMIPS4350 V8.0, 400 MHz, 2 cores
Flash: NAND 128 MiB
RAM: DDR3 128 MiB
Ethernet: 4x 10/100/1000 Mbps
Switch: BCM53134S
Wireless: 802.11b/g/n: BCM435f (integrated)
802.11ac: Quantenna QT3740BC (onboard SoC)
USB: 1x 2.0
LEDs/Buttons: 11x / 2x
Flash instruction, web UI:
1. Reset to defaults using the reset button if the admin password is
unknown
2. Login into the web UI as admin.
Address: http://192.168.0.1
User: admin
Password: VF-ESVodafone-H-500-s or l033i-h500s
3. Go to Settings -> Firmware Update, and select the Openwrt factory
firmware
4. Update the firmware.
5. Wait until it finish, the device will reboot with Openwrt installed
on the alternative image partitions keeping the stock firmware in
the former.
Notes:
- The patch also adds support for the lowi version. Only the factory
firmware is different.
- The integrated Wifi in the Broadcom Soc isn't still supported.
- The Quantenna 802.11ac wifi works ok, but needs to be configured with
the Quantenna client application. It can't be configured with Luci
nor any iw command since it's a separated subsystem linked via
ethernet.
- The BCM53134S external switch is managed via MDIO which isn't
supported in this target. Therefore it will behave as a dumb switch.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
|
| |
Some CFEs are located at the address currently used for relocation and lzma
loader load address, so we need to provide a way to override it.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There is no need to include the CFE bootloader in the Sercomm factory
images.
There might be a case when this could be useful:
- We are running the stock firmware on the first Sercomm image
- The second partition storing the botloader was erased (unlikely)
Even in this case flashing an image without a bootlader is harmless.
Don't include the bootloader in the factory image creation and rid of the
risk of flashing factory images with an untested bootloader partition.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
|
|
|
| |
The BCM63167 is a BCM63268 SoC with a different physical packaging.
Add the CPU ID to allow supporting routers with this SoC (i.e Sercomm
H500-s)
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
| |
SoC is a BCM63168.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
|
|
| |
SoC is a BCM63169.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
|
|
|
| |
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
| |
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
| |
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
| |
Signed-off-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
|
|
| |
- sort device recipes alphabetically
- adjust board name of ELECOM WRC-2533GENT
- harmonize line wrapping
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[rebased]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
| |
Due to a typo, /boot is not properly unmounted after copying the backup
file to it. Fix the typo to solve this.
Fixes: 246916ddf4a1 ("brcm2708: use x86's upgrade scripts for all rpi targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
While the other fq-based qdiscs take advantage of skb->hash and doesn't
recompute it if it is already set, sch_cake does not.
This was a deliberate choice because sch_cake hashes various parts of the
packet header to support its advanced flow isolation modes. However,
foregoing the use of skb->hash entirely loses a few important benefits:
- When skb->hash is set by hardware, a few CPU cycles can be saved by not
hashing again in software.
- Tunnel encapsulations will generally preserve the value of skb->hash from
before the encapsulation, which allows flow-based qdiscs to distinguish
between flows even though the outer packet header no longer has flow
information.
It turns out that we can preserve these desirable properties in many cases,
while still supporting the advanced flow isolation properties of sch_cake.
This patch does so by reusing the skb->hash value as the flow_hash part of
the hashing procedure in cake_hash() only in the following conditions:
- If the skb->hash is marked as covering the flow headers (skb->l4_hash is
set)
AND
- NAT header rewriting is either disabled, or did not change any values
used for hashing. The latter is important to match local-origin packets
such as those of a tunnel endpoint.
The immediate motivation for fixing this was the recent patch to WireGuard
to preserve the skb->hash on encapsulation. As such, this is also what I
tested against; with this patch, added latency under load for competing
flows drops from ~8 ms to sub-1ms on an RRUL test over a WireGuard tunnel
going through a virtual link shaped to 1Gbps using sch_cake. This matches
the results we saw with a similar setup using sch_fq_codel when testing the
WireGuard patch.
Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
|
|
|
|
|
|
|
|
|
|
| |
A direct upgrade from previous swconfig version with
incompatible settings to DSA will break the internet.
Remove SUPPORTED_DEVICES so users cannot upgrade directly.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[rebase after Linksys rename, adjust title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Linksys devices in mvebu target feature a mixed naming,
where parts are based on the official product name (device
node, image; e.g. WRT3200ACM) and parts are based on the
internal code name (DTS file name, compatible, LED labels;
e.g. rango). This inconsistent naming has been perceived
as quite confusing.
A recent attempt by Paul Spooren to harmonize this naming
in kernel has been declined there. However, for us it still
makes sense to apply at least a part of these changes
locally.
Primarily, this patch changes the compatible in DTS and thus
the board name used in various scripts to have them in line
with the device, model and image names. Due to the recent
switch from swconfig to DSA, this allows us to drop
SUPPORTED_DEVICES and thus prevent seamless upgrade between
these incompatible setups.
However, this does not include the LED label rename from
Paul's initial patch: I don't think it's worth keeping the
enormous diff locally for this case, as we can implement
this much easier in 01_leds if we have to live with the
inconsistency anyway.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[rebase, extend to all devices, drop DT LED changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
| |
Add support for adjusting EEE with ethtool
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
|
|
|
| |
Currently enabling VLAN filtering blocks all traffic in the bridge
immediately. That is because DSA ignores all VLAN setup when VLAN
filtering is disabled, and when it is enabled, there is no VLAN entry
in the VLAN table, causing all traffic to be blocked.
Add patches to allow VLAN setup even if VLAN filtering is disabled.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
| |
The new mt76 version splits out the firmware, because the driver can also be
used for MT7663/MT7613
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
Remove dependencies on core kernel headers in host tools used to build perf,
which break on any non-linux system
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
Rename it to wan to match Linksys Armada 385 series
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
| |
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
| |
Backport port mirroring support for mv88e6xxx
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
| |
MAC address is set in board.d script
Interface swapping is not needed anymore as switching to DSA breaks
previous configuration anyway
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
| |
Use ucidef to set up MAC address instead of preinit script
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|
|
|
|
|
|
|
|
| |
eth0 has HW MAC address while eth2 does not.
Use eth0 instead so we don't have to set LAN MAC manually.
Disable unused eth2, until multi CPU port is supported.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
|