aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* ath79: rb912: fix pll init issuesKoen Vandeputte2022-01-131-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds. Investigation shows that the board failed to adapt the ethernet pll values as shown here: [ 5.284359] ag71xx 19000000.eth: failed to read pll-handle property added custom prints in code and triggering a link switch: [ 62.821446] Atheros AG71xx: fast reset [ 62.826442] Atheros AG71xx: update pll 2 [ 62.830494] Atheros AG71xx: no pll regmap! Comparison with another very similar board (rb922 - QCA955x) showed a missing reference clock frequency in dts, which seems to cause a pll init issue. Unfortunately, no errors are printed when this occurs. Adding the frequency property fixes the pll init as it can be parsed now by the ethernet driver. [ 55.861407] Atheros AG71xx: fast reset [ 55.866403] Atheros AG71xx: update pll 2 [ 55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000 Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mikrotik: make soft_config writableOskari Lemmela2022-01-134-4/+0
| | | | | | Parent mtd partition needs to be writable Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* mikrotik: enable variable size eraseOskari Lemmela2022-01-135-0/+401
| | | | | | | Add support for variable size erase blocks. Enable it to all targets which has mikrotik targets. Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
* generic: platform/mikrotik: make soft_config writable without 4K sectorsOskari Lemmela2022-01-131-15/+4
| | | | | | | | | Make soft_config writable in all cases. Performing soft_config commit will fail if mtd partition is not writable. Signed-off-by: Oskari Lemmela <oskari@lemmela.net> [bump rb_softconfig version number] Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* imx: bump SDMA firmware to v3.6Koen Vandeputte2022-01-131-0/+0
| | | | | | No changelog available Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* generic: deny write to uImage.FIT sub-image partitionsDaniel Golle2022-01-112-4/+8
| | | | | | | Set policy bit to force read-only mode on uImage.FIT filesystem sub-images mapped as block partitions by the FIT partition parser. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: Re-enable ARM arch timerDavid Woodhouse2022-01-101-0/+1
| | | | | | | | | CONFIG_ARM_ARCH_TIMER cannot be enabled in the config directly; it is only selected by CONFIG_HAVE_ARM_ARCH_TIMER. We need to enable the latter in our config. Signed-off-by: David Woodhouse <dwmw2@infradead.org> Fixes: 4f1c5b01c1 ("mediatek: mt7623: backport musb, improve HDMI console")
* mediatek: mt7623: Disable power button reset for U7623-02 boardDavid Woodhouse2022-01-101-0/+4
| | | | | | | | | | | | The Unielec U7623 doesn't have a physical power button; I think it's hard wired so that it turns on automatically when power is applied (unlike the Banana Pi R2 which is a pain). So the 'reset on long press of power button' behaviour that we get when we enable the PMIC keyboard driver is kind of unhelpful. Disable it. Signed-off-by: David Woodhouse <dwmw2@infradead.org> Fixes: 0d3f3323a2 ("mediatek: mt7623: enable more hardware features")
* ath79: Add support for OpenMesh OM5P-AC v1Sven Eckelmann2022-01-095-0/+236
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh OM5P-ANSven Eckelmann2022-01-095-2/+247
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR9344 rev 2 * 560/450/225 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 1T1R 2.4 GHz Wi-Fi * 2T2R 5 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + 10/100 Mbps Ethernet + builtin switch port 1 + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: add support for ASUS RP-AC66Tamas Balogh2022-01-096-0/+189
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RP-AC66 Repeater Hardware specifications: Board: AP152 SoC: QCA9563 DRAM: 64MB DDR2 Flash: 25l128 16MB SPI-NOR LAN/WAN: 1x1000M QCA8033 WiFi 5GHz: QCA9880 Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz MAC addresses as verified by OEM firmware: use address source Lan/Wan *:24 art 0x1002 (label) 2G *:24 art 0x1002 5G *:26 art 0x5006 Installation: Asus windows recovery tool: - install the Asus firmware restoration utility - unplug the router, hold the reset button while powering it on - release when the power LED flashes slowly - specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 - Start the Asus firmware restoration utility, specify the factory image and press upload - Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: - set computer to a static ip, 192.168.1.75 - connect computer to the LAN 1 port of the router - hold the reset button while powering on the router for a few seconds - send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* mediatek mt7622: fix 300mhz typo in dtsFritz D. Ansel2022-01-091-0/+27
| | | | | | | | | | | | | | The lowest frequency should be 300MHz, since that is the label assigned to the OPP in the mt7622.dtsi device tree, while there is one missing zero in the actual value. To be clear, the lowest frequency should be 300MHz instead of 30MHz. As mentioned @dangowrt on the OpenWrt forum there is no benefit in leaving 30MHz as the lowest frequency. Signed-off-by: Jip de Beer <gpk6x3591g0l@opayq.com> Signed-off-by: Fritz D. Ansel <fdansel@yandex.ru>
* x86: improve sysinfo handling of dummy valuesStefan Lippers-Hollmann2022-01-081-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | Fall back to using board_vendor and board_name, if known dummy values are used for sys_vendor and product_name. Examples: To be filled by O.E.M.:To be filled by O.E.M. --> INTEL Corporation:ChiefRiver System manufacturer:System Product Name --> ASUSTeK COMPUTER INC.:P8H77-M PRO To Be Filled By O.E.M.:To Be Filled By O.E.M. --> ASRock:Q1900DC-ITX Gigabyte Technology Co., Ltd.:To be filled by O.E.M. --> Gigabyte Technology Co., Ltd.:H77M-D3H empty:empty --> TYAN Computer Corporation:TYAN Toledo i3210W/i3200R S5211 To Be Filled By O.E.M.:To Be Filled By O.E.M. --> ASRock:H77 Pro4-M Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: janitorial work, respect line lengthsAlex Lewontin2022-01-081-19/+41
| | | | | | | This commit breaks up some lines so that they are shorter than 74 charcters. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
* ipq806x: modularize generic subtargetAlex Lewontin2022-01-082-430/+431
| | | | | | | | This commit moves the device profiles within the ipq806x/generic subtarget into their own includable .mk file, to support eventually having subtargets other than generic. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
* lantiq: replace patches with version accepted upstreamAleksander Jan Bajkowski2022-01-085-15/+116
| | | | | | Replace recently added patches with version accepted upstream. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* ramips: add support for Linksys EA6350 v4Nick McKinney2022-01-087-0/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621DAT (880MHz, 2 Cores) - RAM: 128 MB - Flash: 128 MB NAND - Ethernet: 5x 1GiE MT7530 - WiFi: MT7603/MT7613 - USB: 1x USB 3.0 This is another MT7621 device, very similar to other Linksys EA7300 series devices. Installation: Upload the generated factory.bin image via the stock web firmware updater. Reverting to factory firmware: Like other EA7300 devices, this device has an A/B router configuration to prevent bricking. Hard-resetting this device three (3) times will put the device in failsafe (default) mode. At this point, flash the OEM image to itself and reboot. This puts the router back into the 'B' image and allows for a firmware upgrade. Troubleshooting: If the firmware will not boot, first restore the factory as described above. This will then allow the factory.bin update to be applied properly. Signed-off-by: Nick McKinney <nick@ndmckinney.net>
* ramips: add support for RAISECOM MSG1500 X.00Liangkuan Yang2022-01-085-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | RAISECOM MSG1500 X.00 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router. Apart from the general model, there are two ISP customized models: China Mobile and China Telecom. Specifications: - SoC: Mediatek MT7621AT - RAM: 256MiB DDR3 - Flash: 128MiB NAND - Ethernet: 5 * 10/100/1000Mbps: 4 * LAN + 1 * WAN - Switch: MediaTek MT7530 (SoC) - WLAN: 1 * MT7615DN Dual-Band 2.4GHz 2T2R (400Mbps) 5GHz 2T2R (867Mbps) - USB: 1 * USB 2.0 port - Button: 1 * RESET button, 1 * WPS button, 1 * WIFI button - LED: blue color: POWER, WAN, WPS, 2.4G, 5G, LAN1, LAN2, LAN3, LAN4, USB - UART: 1 * serial port header (4-pin) - Power: DC 12V, 1A - Switch: 1 * POWER switch MAC addresses as verified by vendor firmware: use address source LAN C8:XX:XX:3A:XX:E7 Config "protest_lan_mac" ascii (label) WAN C8:XX:XX:3A:XX:EA Config "protest_wan_mac" ascii 5G C8:XX:XX:3A:XX:E8 Factory "0x4" hex 2.4G CA:XX:XX:4A:XX:E8 [not on flash] The increment of the 4th byte for the 2.4g address appears to vary. Reported cases: 5g 2.4g increment C8:XX:XX:90:XX:C3 CA:XX:XX:C0:XX:C3 0x30 C8:XX:XX:3A:XX:08 CA:XX:XX:4A:XX:08 0x10 C8:XX:XX:3A:XX:E8 CA:XX:XX:4A:XX:E8 0x10 Since increment is inconsistent and there is no obvious pattern in swapping bytes, and the 2.4g address has local bit set anyway, it seems safer to use the LAN address with flipped byte here in order to prevent collisions between OpenWrt devices and OEM devices for this interface. This way we at least use an address as base that is definitely owned by the device at hand. Notes: 1. The vendor firmware allows you to connect to the router by telnet. (known version 1.0.0 can open telnet.) There is no official binary firmware available. Backup the important partitions data: "Bootloader", "Config", "Factory", and "firmware". Note that with the vendor firmware the memory is detected only 128MiB and the last 512KiB in NAND flash is not used. 2. The POWER LED is default on after press POWER switch. The WAN and LAN1 - 4 LEDs are wired to ethernet switch. The WPS LED is controlled by MT7615DN's GPIO. Currently there is no proper way to configure it. 3. At the time of adding support the wireless config needs to be set up by editing the wireless config file: * Setting the country code is mandatory, otherwise the router loses connectivity at the next reboot. This is mandatory and can be done from luci. After setting the country code the router boots correctly. A reset with the reset button will fix the issue and the user has to reconfigure. * This is minor since the 5g interface does not come up online although it is not set as disabled. 2 options here: 1- Either run the "wifi" command. Can be added from LuCI in system - startup - local startup and just add wifi above "exit 0". 2- Or add the serialize option in the wireless config file as shown below. This one would work and bring both interfaces automatically at every boot: config wifi-device 'radio0' option serialize '1' config wifi-device 'radio1' option serialize '1' Flash instructions using initramfs image: 1. Press POWER switch to power down if the router is running. 2. Connect PC to one of LAN ports, and set static IP address to "10.10.10.2", netmask to "255.255.255.0", and gateway to "10.10.10.1" manually on the PC. 3. Push and hold the WIFI button, and then power up the router. After about 10s (or you can call the recovery page, see "4" below) you can release the WIFI button. There is no clear indication when the router is entering or has entered into "RAISECOM Router Recovery Mode". 4. Call the recovery page for the router at "http://10.10.10.1". Keep an eye on the "WARNING!! tip" of the recovery page. Click "Choose File" to select initramfs image, then click "Upload". 5. If image is uploaded successfully, you will see the page display "Device is upgrading the firmware... %". Keep an eye on the "WARNING!! tip" of the recovery page. When the page display "Upgrade Successfully", you can set IP address as "automatically obtain". 6. After the rebooting (PC should automatically obtain an IP address), open the SSH connection, then download the sysupgrade image to the router and perform sysupgrade with it. Flash back to vendor firmware: See "Flash instructions 1 - 5" above. The only difference is that in step 4 you should select the vendor firmware which you backup. Signed-off-by: Liangkuan Yang <ylk951207@gmail.com>
* ramips: add support for Joowin WR758AC V1 and V2Rodrigo Araujo2022-01-085-0/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Joowin (aka Comfast) WR758AC V1 and V2 devices. Both have the same wall AP/repeater form factor and differ only in the 5Ghz chipset (V1 has MT7662, V2 has MT7663). OpenWrt developers forum page: https://forum.openwrt.org/t/87355 Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB DDR2 - 2.4 GHz: 802.11b/g/n (MT7603) - 5 GHz: 802.11ac (V1 has MT7662, V2 has MT7663) - Antennas: 4x external single band antennas - LAN: 1x 10/100M - LED: Wifi 3x blue. Programmable - Button: WPS MAC addresses as verified by OEM firmware: use address source LAN *:83 factory 0xe000 2g *:85 factory 0x4 5g *:86 factory 0x8004 How to install: 1- Setup a TFTP server on a machine with IP address 192.168.1.10/24 2- Name the image as `firmware_auto.bin` and place it on the root of the TFTP server 3- Connect the device via Ethernet, it should pick and flash the image Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
* kernel: bump 5.10 to 5.10.90Rui Salvaterra2022-01-078-20/+11
| | | | | | | | Add and enable a new kconfig knob to disable unprivileged eBPF by default. Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.4 to 5.4.170John Audia2022-01-072-15/+5
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/mt7621 Signed-off-by: John Audia <graysky@archlinux.us>
* mediatek: Clause-45 MDIO patch accepted upstreamDaniel Golle2022-01-056-255/+310
| | | | | | | To easy future maintainance, replace the local patch with what has been accepted into net-next and is likely to end up in Linux 5.17. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* qoriq: Expand generic subtarget descriptionMatt Fawcett2022-01-051-1/+3
| | | | | | Signed-off-by: Matt Fawcett <mattytap@icloud.com> [remove trailing whitespace] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* mediatek: let mtk_eth_soc MAC announce 2500Base-T modeDaniel Golle2022-01-051-0/+10
| | | | | | | | To allows Ethernet phys supporting 2500Base-T mode to announce that speed, enable the corresponding bit in mtk_eth_soc driver. This should hopefully unlock 2500Base-T speed on the UniFi 6 LR. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: improve driver support for gen-3 Aquantia Ethernet PHYsDaniel Golle2022-01-054-11/+61
| | | | | | | | | | | | | | * correctly set system side interface, the original patch was errornous and there is a follow-up fix for it * enable phy statistics for AQR112(+R/C) and ARQ412 (ethtool --phy-statistics ethX) Tested, including phy-statistics, on - IEI Puzzle M901 (AQR112, AQR112C, AQR112R) - IEI Puzzle M902 (AQR113, AQR112R) - Ubiquiti UniFi 6 LR (AQR112C) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uml: drop Kernel 5.4Paul Spooren2022-01-043-477/+0
| | | | | | After the switch to Kernel 5.10 the old files are no longer required. Signed-off-by: Paul Spooren <mail@aparcar.org>
* uml: switch to Kernel 5.10Paul Spooren2022-01-041-2/+1
| | | | | | Switch over from testing version. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ipq807x: drop targetPaul Spooren2022-01-034-705/+0
| | | | | | | | | | | The target is in an incomplete state and will not receive Kernel 5.10 support, ego it should be dropped before the next release. People are working on ipq807x with Kernel 5.15 which is only relevant for the second next release. Once a working patchset exists the target can be added again. Signed-off-by: Paul Spooren <mail@aparcar.org>
* kernel: 5.10: backport qca8k new featureAnsuel Smith2022-01-0310-1/+1274
| | | | | | | | | | | Backport qca8k new feature: - Ageing configuration support - Add 2 missing counter on qca8337 - Convert to regmap - Standardize define and code with GENMASK AND BITFILED macro - Add mdb add/del support Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* kernel: 5.10: backport additional qca8k fixesAnsuel Smith2022-01-033-0/+123
| | | | | | | | | Backport 3 additional fixes for qca8k. - Fix MTU calculation - Fix a bug with config set to the wrong PAD when secondary cpu port is defined. - Fix redundant check in parse_port_config Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* kernel: bump 5.10 to 5.10.89Rui Salvaterra2022-01-0312-126/+16
| | | | | | | | | | | Deleted (upstreamed): bcm27xx/patches-5.10/950-0186-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch [1] sunxi/patches-5.10/103-arm64-dts-allwinner-orangepi-zero-plus-fix-PHY-mo.patch [2] [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.89&id=ba696b470839d70c6b8290c1f798bac7fb2a584c [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.89&id=93a957bbf46ceb224b959de61fe85cfc6f71b6c7 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.4 to 5.4.169John Audia2022-01-038-14/+14
| | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/mt7621* *Had to revert 7f1edbd in order to build due to FS#4149 Signed-off-by: John Audia <graysky@archlinux.us>
* ipq806x: ASRock g10: fix bogus read errorsStefan Lippers-Hollmann2022-01-021-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Properly declare that the g10 is booting from NAND and define its correct (larger than on other devices-) boot_pages_size, to prevent the kernel from constantly falling over missing OOB error correction for the bootloader. This patch prevents a constant slew of (bogus) read errors reported by the kernel and keeping the CPU busy and fixes: blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 Buffer I/O error on dev mtdblock0, logical block 0, async page read blk_update_request: I/O error, dev mtdblock0, sector 32 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 40 op 0x0:(READ) flags 0x80700 phys_seg 7 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 48 op 0x0:(READ) flags 0x80700 phys_seg 6 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 56 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 64 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 Buffer I/O error on dev mtdblock0, logical block 1, async page read Buffer I/O error on dev mtdblock1, logical block 0, async page read Buffer I/O error on dev mtdblock1, logical block 1, async page read Buffer I/O error on dev mtdblock2, logical block 0, async page read Buffer I/O error on dev mtdblock2, logical block 1, async page read Buffer I/O error on dev mtdblock3, logical block 0, async page read Buffer I/O error on dev mtdblock3, logical block 0, async page read Buffer I/O error on dev mtdblock4, logical block 0, async page read Buffer I/O error on dev mtdblock4, logical block 1, async page read Suggested-by: Ansuel Smith <ansuelsmth@gmail.com> Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ramips: add ASUS RT-AC1200GU as alt nameShiji Yang2022-01-021-0/+2
| | | | | | | | | | | | RT-AC57U and RT-AC1200GU are the same models sold in different countries. The purpose of this commit is to allow users to easily find the corresponding firmware through the model number on the device label. More specifications: 14e0e4f138e3 ("ramips: add support for ASUS RT-AC57U") Signed-off-by: Shiji Yang <yangshiji66@qq.com> [reword commit title/message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for ipTIME T5004Sungbo Eo2022-01-024-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A. Specifications: * SoC: MT7621AT * RAM: 128 MiB * Flash: NAND 128 MiB * Ethernet: 5x 1GbE * Switch: SoC built-in * UART: J4 (57600 baud) * Pinout: [3V3] (TXD) (RXD) (GND) Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware via recovery mode: 1. Press reset button, power up the device, wait >15s for CPU LED to stop blinking. 2. Upload stock image to TFTP server at 192.168.0.1. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* x86: add/improve support for Sophos SG/XG productsRaylynn Knight2021-12-292-2/+12
| | | | | | | | * Add support for Sophos SG/XG-115 r1, r2 with/without wireless * Add support for Sophos SG/XG-125 r1, r2 with/without wireless * Add wireless support for SG/XG-105 Signed-off-by: Raylynn Knight <rayknight@me.com>
* ath79: add usb-phy-analog to reset list in qca953x.dtsiJinfan Lei2021-12-291-2/+2
| | | | | | | | | | | | | On startup the USB of QCA9531 board can't be initialized successfully. lsusb result as below: root@OpenWrt:~# lsusb unable to initialize libusb: -99 This is because usb-phy-analog is not added to reset list. Signed-off-by: Jinfan Lei <153869379@qq.com> (added linebreaks and small little changes to the commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: 5.10: add patches to fix macronix flashNick Hainke2021-12-293-1/+65
| | | | | | | | | | | | | | | | | | | | | | | mtd: spi-nor: locking support for MX25L6405D Macronix MX25L6405D supports locking with four block-protection bits. Currently, the driver only sets three bits. If the bootloader does not sustain the flash chip in an unlocked state, the flash might be non-writeable. Add the corresponding flag to enable locking support with four bits in the status register. mtd: spi-nor: disable 16-bit-sr for macronix Macronix flash chips seem to consist of only one status register. These chips will not work with the "16-bit Write Status (01h) Command". Disable SNOR_F_HAS_16BIT_SR for all Macronix chips. Refreshed: - 0052-mtd-spi-nor-use-4-bit-locking-for-MX25L12805D.patch Fixes: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Signed-off-by: Nick Hainke <vincent@systemli.org>
* ramips: add support for ipTIME A3004TWonJung Kim2021-12-293-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621. Specifications: - SoC: MT7621 (880MHz) - RAM: DDR3 256M - Flash: NAND 128MB (Macronix NAND 128MiB 3,3V 8-bit) - WiFi: - 2.4GHz: MT7615E - 5GHz : MT7615E - Ethernet: - 4x LAN - 1x WAN - USB: 1 * USB3.0 port - UART: - 3.3V, TX, RX, GND / 57600 8N1 Installation via web interface: 1. Flash initramfs image using OEM's Recovery mode 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: - Flash stock firmware via OEM's Recovery mode How to use OEM's Recovery mode: 1. Power up with holding down the reset key until CPU LED stop blinking. 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0` 3. Flash image via tftp to `192.168.0.1` Additional Notes: This router shares one MT7915E chip for both 2.4Ghz/5Ghz. radio0 will not working on 5Ghz as it's not connected to the antenna. Signed-off-by: WonJung Kim <git@won-jung.kim> (added led dt-bindings) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for WeVO AIR DUOSungbo Eo2021-12-293-1/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on MediaTek MT7620A. Specifications: * SoC: MT7620A * RAM: 64 MiB * Flash: SPI NOR 16 MiB * USB & SATA bridge controller: JMicron JMS567 * SATA 6Gb/s: 2.5" drive slot * USB 3.0: Micro-B * USB 2.0: connected to SoC * Wi-Fi: * 2.4 GHz: SoC built-in * 5 GHz: MT7612EN * Ethernet: 5x 1GbE * Switch: MT7530WU * UART: 4-pin 1.27 mm pitch through-hole (57600 baud) * Pinout: (3V3)|(RXD) (TXD) (GND) Notes: * The drive is accessible through the external USB port only when the router is turned off. Installation via web interface: 1. Flash **initramfs** image through the stock web interface. The image filename should have ".upload" extension. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* bcm27xx: add AMP2 to HifiBerry DAC+ / DAC+ Pro packageTorsten Duwe2021-12-291-6/+9
| | | | | | | | | | | | | According to the vendor [1] these HATs share the same DT overlay: hifiberry-dacplus. The PCM512x-compatible control unit is attached to I2C, so the additional snd-soc-pcm512x-i2c kernel module is required. Also explicitly note the Amp2 support to reduce confusion for those users. [1] <https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/> Signed-off-by: Torsten Duwe <duwe@lst.de> (added bcm27xx tag, changed commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kirkwood: add support for two clones from EndianPawel Dembicki2021-12-294-0/+241
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | They are Endian 4i Edge 200 and his clone Endian UTM Mini. Hardware: - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz - Ram: 512MB (4x Nanya NT5TU128M8GE-AC) - NAND Flash: 512MB (Micron 29F4G08AAC) - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2) - Lan 5: 1x GBE (Marvell 88E1116R-NNC1) - Storage: MicroSD Slot - WLAN: MiniPCIe Slot present, and fitted with SparkLan WPEA-110N/E (Atheros AR9280 chipset) (ONLY Endian UTM Mini WLAN) - USB: 1x USB 2.0 port - Console: RJ-45 port - LEDs: 3x GPIO controlled Notes: - WLAN led (Endian UTM Mini) is drived by MPCIE card Installation by TFTP + serial: - Setup TFTP server and copy initramfs image - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.2 tftpboot 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Installation by USB + serial: - Copy initramfs image to fat32 usb drive - Connect pendrive to USB 2.0 front socket - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' saveenv usb reset fatload usb 0:1 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: add support for NETGEAR ReadyNAS Duo v2Pawel Dembicki2021-12-2912-2/+600
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NETGEAR ReadyNAS Duo v2 is a NAS based on Marvell kirkwood SoC. Specification: - Processor Marvell 88F6282 (1.6 GHz) - 256MB RAM - 128MB NAND - 1x GBE LAN port (PHY: Marvell 88E1318) - 1x USB 2.0 - 2x USB 3.0 - 2x SATA - 3x button - 5x leds - serial on J5 connector accessible from rear panel (115200 8N1) (VCC,TX,RX,GND) (3V3 LOGIC!) Installation by USB + serial: - Copy initramfs image to fat32 usb drive - Connect pendrive to USB 2.0 front socket - Connect serial console - Stop booting in u-boot - Do: usb reset setenv bootargs 'console=ttyS0,115200n8 earlyprintk' setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000' saveenv fatload usb 0:1 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Installation by TFTP + serial: - Setup TFTP server and copy initramfs image - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.2 tftpboot 0x1200000 openwrt-kirkwood-netgear_readynas-duo-v2-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Known issues: - Power button and PHY INTn pin are connected to the same GPIO. It causes that every network restart button is pressed in system. As workaround, button is used as regular BTN_1. For more info please look at file: RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c from Netgear GPL sources. Tested-by: Raylynn Knight <rayknight@me.com> Tested-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: generic: backport linkstation-poweroff driverPawel Dembicki2021-12-294-0/+254
| | | | | | | | | | | Linkstation poweroff driver was added to mvebu target, but is required for kirkwood target too. This commit make two changes: - move linkstation-poweroff support patch from mvebu to generic and replace upstream accepted version - backport small linkstation-poweroff fix from 5.12 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ath79: remove pre-5.10 specific kernel codeDavid Bauer2021-12-295-65/+2
| | | | | | With Kernel 5.4 support removed, we can get rid of this legacy code. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: aw9523: add can_sleep flag for GPIO chipDavid Bauer2021-12-291-1/+1
| | | | | | | | The GPIO expander is connected via I2C, thus the can_sleep flag has to be set to true. This should fix spurious "scheduling while atomic" bugs in the kernel ringbuffer. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: yet again, replace patch with updated pending patchDaniel Golle2021-12-272-37/+125
| | | | | | | | | Upon comment of Russell King ('Oh no, not this "-1 disease" again.') clean up mdio read and write return type and value in mtk_eth_soc driver and also use appropriate return values for bus-busy-timeout- errors in newly added Clause 45 access code. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: replace patch with version sent upstreamDaniel Golle2021-12-272-94/+166
| | | | | | | | | Replace recently added patch 701-net-ethernet-mtk_eth_soc-add-support-for-clause-45-mdio.patch with version sent upstream 701-net-ethernet-mtk_eth_soc-implement-Clause-45-MDIO-access.patch Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath25: add kernel 5.10 supportSergey Ryazanov2021-12-2714-0/+3843
| | | | | | | | | | | | | | | | | | Copy and refresh patches and config from 5.4 to 5.10. Most patches require no more then automatic refresh. The only exception is the Ethernet driver patch, which requires some more work: * drop eth_change_mtu() usage since it was removed from the kernel, it anyway useless for drivers that utilizes alloc_etherdev(); * add the txqueue number argument to the .ndo_tx_timeout callback function; * replace ioremap_nocache() which was finally removed from the kernel by the ioremap() with the same behaviour. Switch target to the new kernel version. Signed-off-by: Daniel Golle <daniel@makrotopia.org> [use KERNEL_TESTING_PATCHVER for now] Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ath25: refresh kernel 5.4 configSergey Ryazanov2021-12-271-54/+2
| | | | | | | | | | | | The target config require some refresh due to the just introduced filtering of the "run-time" options, MIPS eBPF JIT backporting, and so on. The configuration is easily updated using make kernel_oldconfig. So let's update it now in preparation for v5.10 support to reduce the new kernel configuration diff. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-09 01:54:52 +0000