aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* generic: 5.15: backport qca8k fixup for mgmt and mdio read/writeChristian Marangi2023-01-045-0/+531
| | | | | | | | Backport qca8k fixup for mgmt and mdio read/write for kernel 5.15 fixup port dropping and configuration issue. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* generic: 5.10: backport Treat IPv4 segment's lowest address as unicastSeth David Schoen2023-01-041-0/+32
| | | | | | | | | | | | | | | | | | | Backport patch from kernel 5.14. Treat only the highest, not the lowest, IPv4 address within a local subnet as a broadcast address, as subnets do not need two different broadcast addresses and networking documentation consistently prefers the highest address as broadcast. This patch was merged in upstream net-next tree in May 2021 at https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=94c821c74bf5 This eventually frees up one address per subnet. It matches behavior suggested in our Internet-Draft, and also the default behavior of OpenBSD and FreeBSD. Signed-off-by: Seth David Schoen <schoen@loyalty.org>
* kernel: bump 5.15 to 5.15.86John Audia2023-01-0354-224/+158
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: pending-5.15/101-Use-stddefs.h-instead-of-compiler.h.patch[1] ipq806x/patches-5.15/122-01-clk-qcom-clk-krait-fix-wrong-div2-functions.patch[2] bcm27xx/patches-5.15/950-0198-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch[3] Manually rebased: ramips/patches-5.15/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch[4] Added patch/backported: ramips/patches-5.15/107-PCI-mt7621-Add-sentinel-to-quirks-table.patch[5] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=c160505c9b574b346031fdf2c649d19e7939ca11 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=a051e10bfc6906d29dae7a31f0773f2702edfe1b 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=ec1727f89ecd6f2252c0c75e200058819f7ce47a 4. Quilt gave this output when I applied the patch to rebase it: % quilt push -f Applying patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch patching file arch/mips/ralink/Kconfig patching file drivers/pci/controller/Kconfig patching file drivers/pci/controller/Makefile patching file drivers/staging/Kconfig patching file drivers/staging/Makefile patching file drivers/staging/mt7621-pci/Kconfig patching file drivers/staging/mt7621-pci/Makefile patching file drivers/staging/mt7621-pci/TODO patching file drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt patching file drivers/staging/mt7621-pci/pci-mt7621.c Hunk #1 FAILED at 1. Not deleting file drivers/staging/mt7621-pci/pci-mt7621.c as content differs from patch 1 out of 1 hunk FAILED -- saving rejects to file drivers/staging/mt7621-pci/pci-mt7621.c.rej patching file drivers/pci/controller/pcie-mt7621.c Applied patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch (forced; needs refresh) Upon inspecting drivers/staging/mt7621-pci/pci-mt7621.c.rej, it seems that the original patch wants to delete drivers/staging/mt7621-pci/pci-mt7621.c but upstream's version was not an exact match. I opted to delete that file. 5. Suggestion by hauke: https://github.com/torvalds/linux/commit/19098934f910b4d47cb30251dd39ffa57bef9523 "This patch is in upstream kernel, but it was backported to the old staging driver in kernel 5.15." Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* oxnas: sata_oxnas: use ata_link_errRobert Marko2023-01-031-1/+1
| | | | | | | | | | | | | | Kernel 5.15.86 has backported ("ata: libata: move ata_{port,link,dev}_dbg to standard pr_XXX() macros") and this is now causing compilation errors for oxnas SATA driver due to usage of ata_link_printk(). Upstream has migrated to using the appropriate ata_link_{err, warn, notice, info} calls a while ago so its not affected. Lets do the same for oxnas SATA driver and use ata_link_err() instead of ata_link_printk(). Signed-off-by: Robert Marko <robimarko@gmail.com>
* octeontx: add 5.15 testing kernelNick Hainke2023-01-033-14/+24
| | | | | | | | | | Add 5.15 as testing. Refreshed: - 0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch Acked-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
* octeontx: 5.15: copy configNick Hainke2023-01-032-0/+471
| | | | | | Copy config from kernel 5.10 to kernel 5.15. Signed-off-by: Nick Hainke <vincent@systemli.org>
* zynq: add 5.15 testing kernelNick Hainke2023-01-032-10/+14
| | | | | | | | Enable testing kernel. Reviewed-by: Luis Araneda <luaraneda@gmail.com> Tested-by: Luis Araneda <luaraneda@gmail.com> (Digilent Zybo Z7-20) Signed-off-by: Nick Hainke <vincent@systemli.org>
* zynq: 5.15: copy configNick Hainke2023-01-031-0/+548
| | | | | | Copy config from kernel 5.10 to kernel 5.15. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: delete files used for building 5.10 kernelNick Hainke2023-01-0325-2442/+0
| | | | | | | The kernel 5.15 now defaults. Remove unnecessary files. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
* realtek: Migrate to libdeflateOlliver Schinagl2023-01-023-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | Libdeflate is a more advanced gzip compressor, which allows for faster decompression, higher compression speed (factor 3-4), while being fully gzip compatible. Some comparison gzip | libdeflate-gzip | delta | image [openwrt-realtek-rtl839x-*] --------+-----------------+--------+----------------------------------------------- 6589174 | 6298794 | 290380 | d-link_dgs-1210-52-initramfs-kernel.bin 6291632 | 6029488 | 262144 | d-link_dgs-1210-52-squashfs-factory_image1.bin 6292270 | 6030128 | 262142 | d-link_dgs-1210-52-squashfs-sysupgrade.bin 6589142 | 6298760 | 290382 | zyxel_gs1900-48-initramfs-kernel.bin 6292264 | 6030122 | 262142 | zyxel_gs1900-48-squashfs-sysupgrade.bin and changing lzma to (libdeflate-)gzip on existing rtl930x target: gzip | libdeflate-gzip | delta | image [openwrt-realtek-rtl930x-*] --------+-----------------+--------+-------------------------------------- 6816230 | 6510382 | 305848 | zyxel_xgs1250-12-initramfs-kernel.bin Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Rosen Penev <rosenp@gmail.com> Reviewed-by: Sander Vanheule <sander@svanheule.net>
* realtek: Disable boston clockOlliver Schinagl2023-01-018-8/+4
| | | | | | | We are not on the 'boston' platform so no point in having that clock driver enabled. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* tfa-layerscape: Use trusted-firmware-a.mkHauke Mehrtens2022-12-311-14/+14
| | | | | | | | This converts the trusted firmware arm build Makefile to make use of the common trusted-firmware-a.mk file. This also fixes the build with binutils 2.39. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: sysupgrade: allow flashing Linksys factory firmwareTony Ambardar2022-12-311-0/+18
| | | | | | | | | | | | | | | | | Allow forced flashing of a factory firmware image, after checking for the correct FIT magic header and Linksys board-specific footer. Details of the footer are already described in scripts/linksys-image.sh. This is convenient as it avoids using a TFTP server or OEM GUI, and allows restoring OEM firmware or installing a "breaking" OpenWrt update (e.g DSA migration and kernel repartition) directly from the command line. Devices supported at this time include EA6350v3, EA8300, MR8300 and WHW01. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> # WHW01 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: migrate Linksys WHW01 to DSA and re-enableTony Ambardar2022-12-313-2/+22
| | | | | | | | | Convert Linksys WHW01 network configuration to DSA and re-enable builds. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix up Linksys WHW01 board name, device definitionTony Ambardar2022-12-314-11/+8
| | | | | | | | | | | | | | Update the board name defined in DTS to match online documentation and the name encoded into factory firmware. This helps supports flashing firmware factory images using 'sysupgrade'. Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB instead of the correct 74 MB, and defines factory images which include extra adjustments/padding that do not match OEM factory images and may cause problems flashing. Update image size and build recipe to fix these. Suggested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: re-enable EA6350v3, EA8300, MR8300 buildsTony Ambardar2022-12-314-23/+38
| | | | | | | | | | | | | | | | | | | | | | | | | Raise the kernel size from 3 MB to 5 MB for EA6350v3, EA8300 and MR8300, and correspondingly reduce the rootfs size by 2 MB: * modify partition definitions in related .dts files * modify device kernel/image sizes in generic.mk Update to compat-version 2.0 to force factory image usage on sysupgrade, noting the current version 1.1 is an unreleased update for DSA migration. Also update the compat-version message, explaining the need to run one of the following console commands to update U-Boot's kernel-size variable before flashing the OpenWrt factory image. fw_setenv kernsize 500000 # (OpenWrt command line) setenv kernsize 500000 ; saveenv # (U-Boot serial console) Finally, re-enable the 3 devices. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Nicolas TORMO <badulesia.granieri@gmail.com> # MR8300 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* bcm47xx: replace "Devices-database-update-patch" with upstream patchesNick Hainke2022-12-307-268/+428
| | | | | | | | | | | | | Replace "320-MIPS-BCM47XX-Devices-database-update-for-4.x.patch" with upstream patches: - 320-v5.17-MIPS-BCM47XX-Add-board-entry-for-Linksys-WRT320N-v1.patch - 321-v5.17-MIPS-BCM47XX-Add-support-for-Netgear-R6300-v1.patch - 322-v5.17-MIPS-BCM47XX-Add-support-for-Netgear-WN2500RP-v1-v2.patch - 323-v6.0-MIPS-BCM47XX-Add-support-for-Netgear-WNR3500L-v2.patch - 324-v5.17-MIPS-BCM47XX-Add-LEDs-and-buttons-for-Asus-RTN-10U.patch - 325-v5.17-MIPS-BCM47XX-Define-Linksys-WRT310N-V2-buttons.patch Signed-off-by: Nick Hainke <vincent@systemli.org>
* bcm47xx: add tags to upstreamed patchesNick Hainke2022-12-309-0/+0
| | | | | | All of the mtd patches are upstreamed to 5.18. Add tags indicating this. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ramips: enable BBT on NAND in I-O DATA devicesINAGAKI Hiroshi2022-12-302-0/+10
| | | | | | | | | | | This patch enables MediaTek NAND BBT on I-O DATA devices manufactured by MSTC (MitraStar Technology Corp.). [WN-AX2033GR] Tested-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [WN-AX1167GR2, WN-DX1167R, WN-DX1200GR, WN-DX2033GR] Tested-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* mediatek: drop redmi-ax6000 variant with modified envChuanhong Guo2022-12-304-60/+0
| | | | | | | | | | | | | | | | | | | This variant uses xiaomi factory u-boot and modified u-boot-env & bootcmd. By modifying uboot-env, the xiaomi firmware recovery provided in the vendor u-boot doesn't work anymore. It's possible to put u-boot into a state where it refuese to take any serial input. If the u-boot is in this state, users can't restore their firmware without taking the flash off the board. We now have a -stock variant where the vendor u-boot is used in a way that xiaomi firmware recovery still works, and a -ubootmod variant where we get rid of all xiaomi components, have more usable space and no uart console lock. These two should cover all use cases and we don't need this variant anymore. Drop this redmi-ax6000 variant. Existing users of this variant should perform a u-boot mod or restore to the -stock layout. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: Refresh patchesHauke Mehrtens2022-12-291-2/+2
| | | | | | The patch was not applying cleanly any more. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: convert Aruba AP-303H to DSA and enable target againNick Hainke2022-12-293-2/+34
| | | | | | | | | The target was disabled since noone did the DSA conversion. Add the conversion and enable it again. Tested-by: John Walshaw <jjw@myself.com> Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> Signed-off-by: Nick Hainke <vincent@systemli.org>
* mpc85xx: change CPU_TYPE from 8540 to 8548Šimon Bořek2022-12-291-1/+1
| | | | | | | | | | | | | | | | | | All subtargets as p1010, p1020, p2020 uses e500v2 cores [1] [2] [3] [4], so let's force cpu type to 8545 for all mpc85xx target even though there might exist device with e500v1, but there is no such router supported in OpenWrt and because of that it does not make sense to to set CPU_TYPE for each subtarget. All MPC85xx SoC can be found here: https://www.nxp.com/products/processors-and-microcontrollers/legacy-mpu-mcus/powerquicc-processors:POWERQUICC_HOME#powerquicc-iii-mpc85xx [1] https://www.nxp.com/docs/en/application-note/AN2807.pdf [2] https://www.nxp.com/docs/en/fact-sheet/QP1010FS.pdf [3] https://www.nxp.com/docs/en/product-brief/P1020PB.pdf [4] https://www.nxp.com/docs/en/fact-sheet/QP20XXFS.pdf Co-authored-by: Pali Rohár <pali@kernel.org> Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
* mediatek: add new layout for Xiaomi Redmi Router AX6000 for OpenWrt U-BootFurong Xu2022-12-298-20/+92
| | | | | | | | | This new layout is only bootable with OpenWrt U-Boot. It reuses the two crash partions and expands the ubi partion to the end of whole flash. Do not use this layout with stock U-Boot! Signed-off-by: Furong Xu <xfr@outlook.com>
* realtek: deduplicate GS1900 recipesSander Vanheule2022-12-283-23/+18
| | | | | | | | | | ZyXEL GS1900 devices with SoCs from both the RTL838x and RTL839x families share the same image structure and size of the firmware partition. Additionally, the GS1900-48 recipe provided a parameter for the zyxel-vers command, but this parameter is not used. Deduplicate the recipes by moving it to target/linux/realtek/image/common.mk. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: fix GS1900-48 firwmare partitionSander Vanheule2022-12-283-5/+5
| | | | | | | | | | The listed partition size doesn't match the original partition size, and actually overlaps with the following partition. The partition node name for the "firmware" partition also has an extra 'b' compared to the partition offset. Fixes: 47f5a0a3eed5 ("realtek: Add support for ZyXEL GS1900-48 Switch") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: fix ZYXELS_VERS for GS1900-48Sander Vanheule2022-12-281-1/+1
| | | | | | | | | | | | | | | | | The GS1900-48 firmware image is identified by the 'AAHN' ID, while the GS1900-48HP is identified by 'AAHO' [1]. The latter was used, resulting in the following error message when upgrading via the stock web UI: Device only can support firmware from V1.00(AAHN.0) and later version Fix image generation by using the correct ID. [1] https://download.zyxel.com/GS1900-48/firmware/GS1900-48_2.70(AAHN.3)C0_2.pdf Link: https://forum.openwrt.org/t/146533 Fixes: 47f5a0a3eed5 ("realtek: Add support for ZyXEL GS1900-48 Switch") Suggested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: fix default image generationSander Vanheule2022-12-281-3/+3
| | | | | | | | | | | | While cleaning up the makefiles for the realtek target, the order of the default image generating commands was accidentally changed. This caused the image signature to end up somewhere in the middle, misaligning the rootfs. As a result, sysupgrade couldn't verify upgrade images anymore, and devices end up in a boot loop due to the unaligned (and not found) rootfs. Fixes: 94d8b4852b9f ("realtek: Cleanup Makefiles") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: fix calibration-art for some boardsNick Hainke2022-12-281-4/+4
| | | | | | | | | "0x1000" looks suspicious. By looking at data provided by @DragonBluep I was able to identify the correct size for AR9380, AR9287 WiFis. Furthermore, PowerCloud Systems CAP324 has a AR9344 WiFi. Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: fix ethernet regression on mt7986Felix Fietkau2022-12-282-6/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for read/write uboot env to Asus RX-AX53UFelix Baumann2022-12-281-2/+11
| | | | | | | | | | | | | | | | | | Add support for read/writing uboot env by renaming the second partition to its stock label "nvram" and remove the deemed unnecessary "read-only". Split the first partition "u-boot" in two, in order to allow `fw_setenv` safe write-access to the uboot environment variables. This implements hauke's request from [1]. Based on the patch provided by Shiji Yang. [1] https://github.com/openwrt/openwrt/pull/10400#discussion_r945153224 Co-Authored-By: Shiji Yang <yangshiji66@qq.com> Signed-off-by: Felix Baumann <felix.bau@gmx.de> [ improve commit title and description, fix some whitespace problem ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* realtek: Fix reset register accessBirger Koblitz2022-12-282-2/+2
| | | | | | | | | | | The reset register on RTL93xx not merely have bits to execute a reset of a hardware component, but also configuration bits for reset procedures. Keep them during executing a reset. Signed-off-by: Birger Koblitz <git@birger-koblitz.de> Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> [backport to 5.10 kernel] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* bcm27xx: fix BCMGENET kernel configÁlvaro Fernández Rojas2022-12-282-0/+54
| | | | | | | | | | | Revert backported upstream commits 421f8663b3a7 and 8d820bc9d12b, which have introduced a regression in BCMGENET kconfig that disabled the network driver for the Raspberry Pi. Fixes: 0c405bceba11 ("kernel: bump 5.15 to 5.15.85") Fixes: e9008223268c ("kernel: bump 5.15 to 5.15.84") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: mediatek: fix WED offload regression on MT7622Felix Fietkau2022-12-271-0/+55
| | | | | | Fix dealing with DSA untagging offload Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: mediatek: improve ethernet fix for dealing with small fragmentsFelix Fietkau2022-12-272-21/+37
| | | | | | | Replace the workaround on MT7986 with a proper fix. Software workaround is still needed on older chips. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* realtek: Reduce variable scopesOlliver Schinagl2022-12-2712-443/+335
| | | | | | | | | | | | | | Linus prefers to have loop initializers nice and tightly scoped. In OpenWRT this has been possible since 41a1a652fbd4 ("kernel: backport gnu11 upgrade"). This patch cleans up variable scope while trying to do the above for 'simple for loops'. This cleans up and simplifies some functions and code, and pulls in variables to a smaller scope. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* realtek: Cleanup MakefilesOlliver Schinagl2022-12-279-31/+110
| | | | | | | Our current Makefiles a little bit messy and can be improved somewhat, both in whitespace and in style. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* realtek: Replace C++ style commentsOlliver Schinagl2022-12-2720-964/+966
| | | | | | | The only exception to C++ style comments are SPDX license identifier markers at the start of C files (even headers have C style markers). Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* realtek: Whitespace and codestyle cleanupOlliver Schinagl2022-12-2725-810/+767
| | | | | | | | Fix some ugly whitepsaces and codestyle issues around the realtek sources. While this is by no means perfect, it catches what it caught. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* realtek: add cond_resched to loops accessing the FDB tableJan Hoffmann2022-12-274-0/+12
| | | | | | | | | A full loop accessing all FDB entries can take several milliseconds (on RTL839x about 20 ms), so give other kernel tasks a chance to run. This is especially important for rtl83xx_port_fdb_dump which is itself called in a loop for all ports by the kernel. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* realtek: restructure rtl_table_read/writeJan Hoffmann2022-12-274-28/+62
| | | | | | | | | | | | | | | | These two functions are identical apart from writing different values to the read/write bit. Create a new function rtl_table_exec to reduce code duplication. Also replace the unbounded busy-waiting loop. The new implementation may sleep, but as the hardware typically responds before the first poll, any callers doing many table accesses still need to make sure not to block other kernel tasks themselves. So far, polling timeout errors are only handled by logging an error, but a return value is added to allow proper handling in the future. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* realtek: simplify log messages in rtl83xx_mdio_probeJan Hoffmann2022-12-272-14/+2
| | | | | | | | | | This function currently prints three messages for every switch port at KERN_INFO level. This takes a considerable amount of time during bootup and can even trigger an external watchdog. Replace these log messages by a single one at KERN_DEBUG level. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* realtek: don't set L2LEARNING flag in rtl83xx TX headerJan Hoffmann2022-12-272-4/+4
| | | | | | | | | | | | | | | | | | | As learning for the CPU port is now disabled globally, the bit in the TX header doesn't have any effect anymore. Remove it to make the header consistent with the global configuration. Originally, this change was intended to be applied before commit eb456aedfe24 ("realtek: use assisted learning on CPU port"), which is why the commit message incorrectly mentions that the TX header already disables learning. The reason for disabling learning on the CPU port in the first place is that it doesn't work correctly when packets are trapped to the CPU and then forwarded by the CPU to other ports. In that case, the switch would incorrectly learn the CPU port as source. An example that triggered this issue are Multicast Listener Reports and IGMP membership reports. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* sunxi: ensure NanoPi R1 has unique MAC addressJan-Niklas Burfeind2022-12-252-11/+27
| | | | | | | | | | | | | | | | | | | | Ensure the MAC address for all NanoPi R1 boards is assigned uniquely for each board. The vendor ships the device in two variants; one with and one without eMMC; but both without static mac-addresses. In order to assign both board types unique MAC addresses, fall back on the same method used for the NanoPi R2S and R4S in case the EEPROM chip is not present by generating the board MAC from the SD card CID. [0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R1#Hardware_Spec Similar too and based on: commit b5675f500daf ("rockchip: ensure NanoPi R4S has unique MAC address") Co-authored-by: David Bauer <mail@david-bauer.net> Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* kernel: bump 5.10 to 5.10.161John Audia2022-12-242-2/+2
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.85John Audia2022-12-244-4/+4
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B Run-tested: bcm2711/RPi4B Signed-off-by: John Audia <therealgraysky@proton.me>
* mpc85xx: drop empty patch as it backported to LTS kernel 5.15.70Josef Schlehofer2022-12-241-0/+0
| | | | | | | | | This patch is part of Linux kernel 5.15.70, the content was removed, but the empty file is still being carried over the repository, so remove it once for all Fixes: e1b009c ("kernel: bump 5.15 to 5.15.70") Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* realtek: 5.15: Fix incorrect switch patchesOlliver Schinagl2022-12-241-0/+53
| | | | | | | | | Add correct header to patche(s) to be correctly used by git am and have better tracking of it. See commit f1f97db627b2 ("realtek: Convert incorrect v5.10 patches"). Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* realtek: 5.10: Fix incorrect switch patchesOlliver Schinagl2022-12-241-0/+53
| | | | | | | | | Add correct header to patche(s) to be correctly used by git am and have better tracking of it. See commit f1f97db627b2 ("realtek: Convert incorrect v5.10 patches"). Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* omap: add generic subtargetChristian Marangi2022-12-232-0/+2
| | | | | | | Same game as for 853e4dd3062df7cb5704b15d6af6730e3194b571. Add generic to the filenames. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-21 08:38:22 +0000