aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* mpc85xx: add patch to fix gpio mpc8xxxJosef Schlehofer2022-09-111-0/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Backports patch, which is currently on review [1] for kernel 5.10 and kernel 5.15, where it applies cleanly. This was tested on CZ.NIC Turris 1.1 router running OpenWrt 21.02.03 with kernel 5.15. Before: - In /var/log/messages: ``` [ 16.392988] lm90 0-004c: cannot request IRQ 48 [ 16.398280] lm90: probe of 0-004c failed with error -22 ``` - Sensors does not work: ``` root@turris:~# sensors No sensors found! Make sure you loaded all the kernel drivers you need. Try sensors-detect to find out which these are. ``` After: ``` root@turris:/# sensors sa56004-i2c-0-4c Adapter: MPC adapter (i2c@3000) temp1: +44.0°C (low = +0.0°C, high = +70.0°C) (crit = +85.0°C, hyst = +75.0°C) temp2: +73.8°C (low = +0.0°C, high = +70.0°C) ALARM (HIGH) (crit = +85.0°C, hyst = +75.0°C) ``` [1] https://lore.kernel.org/linux-gpio/20220906105431.30911-1-pali@kernel.org/ Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* ramips: add support for Linksys E7350Rosen Penev2022-09-117-2/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | Linksys E7350 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for Belkin RT1800Rosen Penev2022-09-117-0/+225
| | | | | | | | | | | | | | | | | | | | | | | | | | | Belkin RT1800 is an 802.11ax (Wi-Fi 6) router, based on MediaTek MT7621A. Specifications: - SoC: MT7621 (880MHz, 2 Cores) - RAM: 256 MB - Flash: 128 MB NAND - Wi-Fi: - MT7915D: 2.4/5 GHz (DBDC) - Ethernet: 5x 1GiE MT7530 - USB: 1x USB 3.0 - UART: J4 (57600 baud) - Pinout: [3V3] (TXD) (RXD) (blank) (GND) Notes: * This device has a dual-boot partition scheme, but this firmware works only on boot partition 1. Installation: Upload the generated factory.bin image via the stock web firmware updater. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add RT-N600 alternative name to RT-AC1200Ray Wang2022-09-111-0/+2
| | | | | | | | RT-N600 is internally the same as RT-AC1200, as veryfied by @russinnes . Adding alt_name so that people can find it in firmware selector. Signed-off-by: Ray Wang <raywang777@foxmail.com> Tested-by: Russ Innes <russ.innes@gmail.com>
* ramips: add support for Kroks Rt-Cse SIM Injector DSAndrey Butirsky2022-09-113-0/+73
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Aka Kroks Rt-Cse5 UW DRSIM (KNdRt31R16), ID 1958: https://kroks.ru/search/?text=1958 See Kroks OpenWrt fork for support of other models: https://github.com/kroks-free/openwrt Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 5x 10/100 Mbps - 2.4 GHz: b/g/n SoC - USB: 1x - SIM-reader: 2x (driven by a dedicated chip with it's own firmware) - Buttons: reset - LEDs: 1x Power, 1x Wi-Fi, 12x others (SIM status, Internet, etc.) Flashing: - sysupgrade image via stock firmware WEB interface, IP: 192.168.1.254 - U-Boot launches a WEB server if Reset button is held during power up, IP: 192.168.1.1 MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* ramips: add support for Kroks Rt-Pot mXw DS RSIM routerAndrey Butirsky2022-09-114-0/+192
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Aka "Kroks KNdRt31R19". Ported from v19.07.8 of OpenWrt fork: see https://github.com/kroks-free/openwrt for support of other models. Device specs: - CPU: MediaTek MT7628AN - Flash: 16MB SPI NOR - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - mPCIe: 1x (usually equipped with an LTE modem by vendor) - Buttons: reset - LEDs: 1x Modem, 1x Injector, 1x Wi-Fi, 1x Status Flashing: - sysupgrade image via stock firmware WEB interface. - U-Boot launches a WEB server if Reset button is held during power up. Server IP: 192.168.1.1 SIM card switching: The device supports up to 4 SIM cards - 2 locally on board and 2 on remote SIM-injector. By default, 1-st local SIM is active. To switch to e.g. 1-st remote SIM: echo 0 > /sys/class/gpio/modem1power/value echo 0 > /sys/class/gpio/modem1sim1/value echo 1 > /sys/class/gpio/modem1rsim1/value echo 1 > /sys/class/gpio/modem1power/value MAC addresses as verified by OEM firmware: vendor OpenWrt source LAN eth0 factory 0x4 (label) 2g wlan0 label Signed-off-by: Kroks <dev@kroks.ru> [butirsky@gmail.com: port to master; drop dts-v1] Signed-off-by: Andrey Butirsky <butirsky@gmail.com>
* kernel: bump 5.10 to 5.10.142John Audia2022-09-114-6/+6
| | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.141John Audia2022-09-1123-59/+59
| | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* ramips: add config-5.15 for mt7620 subtargetDaniel Golle2022-09-101-0/+196
| | | | | | | Add Kernel config for testing Linux 5.15 for the mt7620 subtarget. Tested on Youku YK-L1 which boots fine. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* realtek: add support for TP-Link SG2452P v4 aka T1600G-52PS v4Andreas Böhler2022-09-104-1/+428
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is an RTL8393-based switch with 802.3af on all 48 ports. Specifications: --------------- * SoC: Realtek RTL8393M * Flash: 32 MiB SPI flash * RAM: 256 MiB * Ethernet: 48x 10/100/1000 Mbps with PoE+ * Buttons: 1x "Reset" button, 1x "Speed" button * UART: 1x serial header, unpopulated * PoE: 12x TI TPS23861 I2C PoE controller, 384W PoE budget * SFP: 4 SFP ports Works: ------ - (48) RJ-45 ethernet ports - Switch functions - Buttons - All LEDs on front panel except port LEDs - Fan monitoring and basic control Not yet enabled: ---------------- - PoE - ICs are not in AUTO mode, so the kernel driver is not usable - Port LEDs - SFP cages Install via web interface: ------------------------- Not supported at this time. Install via serial console/tftp: -------------------------------- The U-Boot firmware drops to a TP-Link specific "BOOTUTIL" shell at 38400 baud. There is no known way to exit out of this shell, and no way to do anything useful. Ideally, one would trick the bootloader into flashing the sysupgrade image first. However, if the image exceeds 6MiB in size, it will not work. To install OpenWRT: Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" Power on device, and stop boot by pressing any key. Once the shell is active: 1. Ground out the CLK (pin 16) of the ROM (U6) 2. Select option "3. Start" 3. Bootloader notes that "The kernel has been damaged!" 4. Release CLK as soon as bootloader thinks image is corrupted. 5. Bootloader enters automatic recovery -- details printed on console 6. Watch as the bootloader flashes and boots OpenWRT. Blind install via tftp: ----------------------- This method works when it's not feasible to install a serial header. Prepare a tftp server with: 1. server address: 192.168.0.146 2. the image as: "uImage.img" 3. Watch network traffic (tcpdump or wireshark works) 4. Power on the device. 5. Wait 1-2 seconds then ground out the CLK (pin 16) of the ROM (U6) 6. When 192.168.0.30 makes tftp requests, release pin 16 7. Wait 2-3 minutes for device to auto-flash and boot OpenWRT Signed-off-by: Andreas Böhler <dev@aboehler.at>
* x86: setup netdev paths for MX100Martin Kennedy2022-09-101-1/+13
| | | | | | | | | | | | | | | | The Meraki MX100 has ten 1000BASE-T and 2 SFP ethernet ports through 3, 4-port PCIe devices. The default enumeration of these network devices' names does not correspond to their labeling. Fix this by explicitly naming the devices, mapping against their sysfs path. Note that these default network names can only be up to 8 characters, because we can have up to 8 characters of modifiers (e.g. ^br-, .4096$), and because the maximum network interface name is 16 characters long. Signed-off-by: Martin Kennedy <hurricos@gmail.com> [lowercase subject] Signed-off-by: Paul Spooren <mail@aparcar.org>
* mediatek: filogic: use WPS button instead of RST on BPi-R3Daniel Golle2022-09-101-0/+12
| | | | | | | | | The GPIO used for the RST button is also used for PCIe-CLKREQ signal. Hence it cannot be used as button signal if PCIe is also used. Wire up WPS button to serve as KEY_RESTART in Linux and "reset" button in U-Boot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Makefile: replace head call with grep's -mRosen Penev2022-09-101-1/+1
| | | | | | head is not necessary here. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mediatek: bananapi-r3: remove kmod-btmtkuart from default packagesDaniel Golle2022-09-101-1/+1
| | | | | | | The package kmod-btmtkuart is specific for MT7622 and isn't available for MT7986 (which doesn't have this built-in Bluetooth like MT7622). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: fix build on bcm27xx target platformDaniel Golle2022-09-106-30/+11
| | | | | | | | | The bump to Linux 5.15.67 brought some changes in the VC4 display driver which we had also patched downstream. Fix our local patches to fix the build. Fixes: fbe2f7db86 ("kernel: bump 5.15 to 5.15.67") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* rockchip: add system-LED aliases specific to OpenWrtDavid Bauer2022-09-102-0/+32
| | | | | | | Add the aliases sections required to detect LEDs specific to OpenWrt boot / update indication for the NanoPi R4S. Signed-off-by: David Bauer <mail@david-bauer.net>
* rockchip: ensure NanoPi R4S has unique MAC addressDavid Bauer2022-09-101-5/+28
| | | | | | | | | | | | | | | | | Ensure the MAC address for all NanoPi R4S boards is assigned unique for each board. FriendlyElec ship two versions of the R4S: The standard as well as the enterprise edition with only the enterprise edition including the EEPROM chip that stores the unique MAC address. In order to assign both board types unique MAC addresses, fall back on the same method used for the NanoPi R2S in case the EEPROM chip is not present by generating the board MAC from the SD card CID. [0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R4S#Differences_Between_R4S_Standard_Version_.26_R4S_Enterprise_Version Signed-off-by: David Bauer <mail@david-bauer.net>
* realtek: fix RTL839x receive tag decodingBjørn Mork2022-09-091-2/+2
| | | | | | | | | | The previous fixup was incomplete, and the offsets for the queue and crc_error cpu_tag bitfields were still wrong on RTL839x. Fixes: 545c6113c93b ("realtek: fix RTL838x receive tag decoding") Suggested-by: Jan Hoffmann <jan@3e8.eu> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kernel: backport MediaTek USB Bluetooth additionsDaniel Golle2022-09-095-0/+289
| | | | | | | Backport commits from linux.git adding support for various MT7921 Bluetooth USB IDs. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: rename some patchesDaniel Golle2022-09-094-0/+0
| | | | | | | To ease maintainance rename patches to contain the kernel version they have first been part of. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: 5.15: add missing patch suffixChukun Pan2022-09-091-0/+0
| | | | | | | The 213 patch is missing filename suffix. Fix it. Fixes: dabcaac ("mediatek: add mt7986 soc support to the target") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: mt7986a/b-rfb: fix 02_network setupChukun Pan2022-09-091-1/+1
| | | | | | | | According to the device tree, the lan ports are lan0 to lan3, and the wan port is eth1. Fixes: cffc77a ("mediatek: add filogic subtarget") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* kernel: bump 5.15 to 5.15.67John Audia2022-09-0941-73/+73
| | | | | | | | | | All patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: add # CONFIG_ARM64_ERRATUM_2441009 symbolJohn Audia2022-09-091-0/+1
| | | | | | | | No current targets are ARMv9 or Cortex-A510 so comment the new symbol.[1] 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/arm64/Kconfig?id=v5.15.65&id2=v5.15.64 Signed-off-by: John Audia <therealgraysky@proton.me>
* ipq40xx: add LTE packages for GL-AP1300David Bauer2022-09-091-1/+1
| | | | | | | Add LTE packages required for operating the LTE modem optionally shipped with the GL-AP1300. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: switch to 5.15 as default kernelNick Hainke2022-09-091-2/+1
| | | | | | | | | | | | The testing kernel received now multiple months of testing. Set 5.15 as default to give it a test with a broader audience. Tested on: - MikroTik SXTsq 5 AC - FritzBox 4040/7530 - ZyXEL NBG6617 Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: mt7530: add support for in-band managed linkDaniel Golle2022-09-091-0/+123
| | | | | | | Add support for in-band managed link status to support SFP cage connected to port 5 of the MT7531 switch on the Bananapi BPi-R3. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: mtk_sgmii: re-organize PCS link status reportingDaniel Golle2022-09-091-4/+6
| | | | | | Don't report speed in case link is down. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* realtek: fix RTL838x receive tag decodingBjørn Mork2022-09-081-3/+6
| | | | | | | | | | | | | | | | | | | Commit dc9cc0d3e2a1 ("realtek: add QoS and rate control") replaced a 16 bit reserved field in the RTL83xx packet header with the initial cpu_tag word, shifting the real cpu_tag fields by one. Adjusting for this new shift was partially forgotten in the new RX tag decoders. This caused the switch to block IGMP, effectively blocking IPv4 multicast. The bug was partially fixed by commit 9d847244d9fd ("realtek: fix RTL839X receive tag decoding") Fix on RTL838x too, including correct NIC_RX_REASON_SPECIAL_TRAP value. Suggested-by: Jan Hoffmann <jan@3e8.eu> Fixes: dc9cc0d3e2a1 ("realtek: add QoS and rate control") Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mediatek: fix typo in bpi-r64 image recipeDaniel Golle2022-09-081-1/+1
| | | | | | | Janusz Dziedzic reported a typo introduced by a recent commit. Fix it. Fixes: 50c892d67b ("mediatek: bpi-r64: make initramfs/recovery optional") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add support for ZTE MF281David Bauer2022-09-083-4/+296
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the ZTE MF281 battery-powered WiFi router. Hardware -------- SoC: Qualcomm Atheros QCA9563 RAM: 128M DDR2 FLASH: 2M SPI-NOR (GigaDevice GD25Q16) 128M SPI-NAND (GigaDevice) WLAN: QCA9563 2T2R 802.11 abgn QCA9886 2T2R 802.11 nac WWAN: ASRMicro ASR1826 ETH: Qualcomm Atheros QCA8337 UART: 115200 8n1 Unpopulated connector next to SIM slot (SIM) GND - RX - TX - 3V3 Don't connect 3V3 BUTTON: Reset - WPS LED: 1x debug-LED (internal) LEDs on front of the device are controlled using the modem CPU and can not be controlled by OpenWrt Installation ------------ 1. Connect to the serial console. Power up the device and interrupt autoboot when prompted 2. Connect a TFTP server reachable at 192.168.1.66 to the ethernet port. Serve the OpenWrt initramfs image as "speedbox-2.bin" 3. Boot the initramfs image using U-Boot $ setenv serverip 192.168.1.66 $ setenv ipaddr 192.168.1.154 $ tftpboot 0x84000000 speedbox-2.bin $ bootm 4. Copy the OpenWrt factory image to the device using scp and write to the NAND flash $ mtd write /path/to/openwrt/factory.bin firmware WWAN ---- The WWAN card can be used with OpenWrt. Example configuration for connection with a unauthenticated dual-stack APN: network.lte=interface network.lte.proto='ncm' network.lte.device='/dev/ttyACM0' network.lte.pdptype='IPV4V6' network.lte.apn='internet.telekom' network.lte.ipv6='auto' network.lte.delay='10' The WWAN card is running a modified version of OpenWrt and handles power-management as well as the LED controller (AW9523). A root shell can be acquired by installing adb using opkg and executing "adb shell". Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: bpi-r64: make initramfs/recovery optionalDaniel Golle2022-09-081-2/+7
| | | | | | | | | Only include recovery image in SD card image generated for the BananaPi BPi-R64 if building with CONFIG_TARGET_ROOTFS_INITRAMFS This allows to build images larger than 32 MB (the limit for initramfs/recovery image) by deselecting initramfs. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: bpi-r3: make initramfs/recovery optionalDaniel Golle2022-09-081-2/+7
| | | | | | | | | Only include recovery image in SD card image generated for the BananaPi BPi-R3 if building with CONFIG_TARGET_ROOTFS_INITRAMFS. This allows to build images larger than 32 MB (the limit for initramfs/recovery image) by deselecting initramfs. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq-wifi: add Pakedge WR-1 supportTomasz Maciej Nowak2022-09-072-0/+5
| | | | | | | | | | Calibration variants: Pakedge-WR-1 ETSI, FCC and IC-2.4GHz Pakedge-WR-1-ACMA ACMA Pakedge-WR-1-IC IC-5GHz Pakedge-WR-1-SRRC SRRC Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: add support for Pakedge WR-1Tomasz Maciej Nowak2022-09-074-0/+291
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pakedge WR-1 is a dual-band wireless router. Specification SoC: Qualcomm Atheros IPQ4018 RAM: 256 MB DDR3 Flash: 32 MB SPI NOR WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R integrated Ethernet: 5x 10/100/1000 Mbps QCA8075 USB: 1x 2.0 LEDS: 8x (3 GPIO controlled, 5 connected to switch) Buttons: 1x GPIO controlled UART: pin header J5 1. 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Rename initramfs image to: openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb and copy it to USB flash drive with FAT32 file system. 2. Connect USB flash drive to the router and apply power while pressing reset button. Hold the button, on the lates bootloader version, when Power and WiFi-5 LEDs will start blinking release it. For the older bootloader holding it for 15 seconds should suffice. 3. Now the router boots the initramfs image, at some point (close to one minute) the Power LED will start blinking, when stops, router is fully booted. 4. Connect to one of LAN ports and use SSH to open the shell at 192.168.1.1. 5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if, at some point, You want to go back to original firmware. The firmware provided by manufacturer on its site is encrypted and U-Boot accepts only decrypted factory images, so there's no way to restore original firmware. 6. If the backup is prepared, transfer the sysupgrade image to the router and use 'sysupgrade' command to flash it. 7. After successful flashing router will reboot. At some point the Power LED will start blinking, wait till it stops, then router is ready for configuration. Additional information U-Boot command line is password protected. Password is unknown. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mediatek: remove redundant patchDaniel Golle2022-09-071-47/+0
| | | | | | | | | | | | | | | The patch 921-mt7986-add-mmc-support.patch introduced by commit dabcaac443 ("mediatek: add mt7986 soc support to the target") has never been applied in a way that it would have any effect as it actually created a file target/linux/generic/patches-5.15/... in the kernel tree and was probably a patch intended to be applied to openwrt.git instead of being put into kernel patches folder as a file. As an upstream commit from vanilla Linux also adding support for MT7986 to the mtk-sd driver has already been included we can remove that old patch. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: mtk_eth_soc: fix hw hash reporting for MT7986Daniel Golle2022-09-076-8/+82
| | | | | | Import patch from Linux 6.0. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: refresh patchesDaniel Golle2022-09-075-23/+14
| | | | | | | The introduction of the new Airoha target has left the tree in an unfresh state. Refresh patches to improve that situation. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: rework Huawei-compatible OEM SFP GE-TDaniel Golle2022-09-061-31/+49
| | | | | | | | | | | This patch was added in 09b086eecaa545cf7f30bc7e394a32751e25db65 ("kernel: add quirk for Huawei-compatible OEM SFP GE-T"). Add patch title, description and SoB to follow OpenWrt's developer guide for working patches to prepare it for being sent upstream. This patch should be discussed with Russell King and merged to Linux kernel. Co-authored-by: Josef Schlehofer <pepe.schlehofer@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: add support for HALNy HL-GSFP and other related fixesJosef Schlehofer2022-09-066-0/+605
| | | | | | | | | | | | It was reported on Turris forum [1] that HALNy HL-GSFP module does not work as it should with kernel 5.15. Russell King prepared this patch series, which fixes broken SFP module to work. Compile and run tested with Turris Omnia. [1] https://forum.turris.cz/t/hbl-turrisos-6-0-alpha2-halny-hl-gsfp-sfp-gpon-stick-problems/17547 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* mediatek: fix sysupgrade on MTK7986 rfba APDaniel Golle2022-09-061-0/+1
| | | | | | | | | A line in platform.sh was accidentally removed when adding support for the Bananapi BPi-R3. Re-add it to fix sysupgrade on the MTK7986 rfba AP. Fixes: a96382c1bb ("mediatek: add support for Bananapi BPi-R3") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: move 5.15 testing kernel to common MakefileNick Hainke2022-09-065-8/+1
| | | | | | | All subtargets are using now 5.15 as testing kernel. Move KERNEL_TESTING_PATCHVER:=5.15 to the common Makefile. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: tiny: add 5.15 support for tiny subtargetNick Hainke2022-09-061-0/+2
| | | | | | Tested on Ubiquiti Nanostation M5 XM with low_mem. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: add low_mem to tiny imageNick Hainke2022-09-061-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Devices with SMALL_FLASH enabled have "SQUASHFS_BLOCK_SIZE=1024" in their config. This significantly increases the cache memory required by squashfs [0]. This commit enables low_mem leading to a much better performance because the SQUASHFS_BLOCK_SIZE is reduced to 256. Example Nanostation M5 (XM): The image size increases by 128 KiB. However, the memory statisitcs look much better: Default tiny build: ------ MemTotal: 26020 kB MemFree: 5648 kB MemAvailable: 6112 kB Buffers: 0 kB Cached: 3044 kB low_mem enabled: ----- MemTotal: 26976 kB MemFree: 6748 kB MemAvailable: 11504 kB Buffers: 0 kB Cached: 7204 kB [0] - https://github.com/freifunk-gluon/gluon/commit/7e8af99cf504ca1dc389f282a0c94f4a911571be Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: add support for Extreme Networks WS-AP3915iDavid Bauer2022-09-065-0/+296
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- Qualcomm IPQ4029 WiSoC 2T2R 802.11 abgn 2T2R 802.11 nac Macronix MX25L25635E SPI-NOR (32M) 512M DDR3 RAM 1x Gigabit LAN 1x Cisco RJ-45 Console port Settings: 115200 8N1 Installation ------------ 1. Attach to the Console port. Power up the device and press the s key to interrupt autoboot. 2. The default username / password to the bootloader is admin / new2day 3. Update the bootcommand to allow loading OpenWrt. $ setenv ramboot_openwrt "setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x86000000 openwrt-3915.bin; bootm" $ setenv boot_openwrt "sf probe; sf read 0x88000000 0x280000 0xc00000; bootm 0x88000000" $ setenv bootcmd "run boot_openwrt" $ saveenv 4. Download the OpenWrt initramfs image. Serve it using a TFTP server as "openwrt-3915.bin" at 192.1681.66. 5. Download & boot the OpenWrt initramfs image on the access point. $ run ramboot_openwrt 6. Wait for OpenWrt to start. 7. Download and transfer the sysupgrade image to the device using e.g. SCP. 8. Install OpenWrt to the device using "sysupgrade" $ sysupgrade -n /path/to/openwrt.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: point to externally compiled dtbs in recipesTomasz Maciej Nowak2022-09-064-194/+11
| | | | | | | | | | | | | | | | Adjusting dts will cause a rebuild of whole kernel as the buildroot considers this a part of kernel source. It's a royal PITA when trying to prepare support for new device, since this takes a lot of time on slower systems. As it stands, buildroot itself, with own rule, also compiles dtbs and the results are $(KDIR)/image-$(DEVICE_DTS).dtb. With setting DEVICE_DTS_DIR to directory holding the device dts (similarly to some other targets), buildroot doesn't consider changed dts as part of kernel source and rebuilds only dtb. This really speeds up development. And since the kernel built dts are no longer used, drop the paches adding dtses to its build. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* kernel: fix mvneta Ethernet after generic phylink validateDaniel Golle2022-09-0510-35/+1222
| | | | | | | | Import patches from Linux v5.16 and v5.17 to get 2500Base-X SFP working again with mvneta driver after the generic phylink validate backport. Fixes: aab466f422 ("kernel: backport generic phylink validate") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: fix fallout after etron spinand backportFelix Fietkau2022-09-051-5/+5
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* airoha: Add new target platformDaniel Danzberger2022-09-0518-0/+1867
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Airoha is a new ARM platform based on Cortex-A53 which has recently been merged into linux-next. Due to BootROM limitations on this platform, the Cortex-A53 can't run in Aarch64 mode and code must be compiled for 32-Bit ARM. This support is based mostly on those linux-next commits backported for kernel 5.15. Patches: 1 - platform support = linux-next 2 - clock driver = linux-next 3 - gpio driver = linux-next 4 - linux,usable-memory-range dts support = linux-next 5 - mtd spinand driver 6 - spi driver 7 - pci driver (kconfig only, uses mediatek PCI) = linux-next Still missing: - Ethernet driver - Sysupgrade support A.t.m there exists one subtarget EN7523 with only one evaluation board. The initramfs can be run with the following commands from u-boot: - u-boot> setenv bootfile \ openwrt-airoha-airoha_en7523-evb-initramfs-kernel.bin u-boot> tftpboot u-boot> bootm 0x81800000 - Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
* realtek: replace fix for spurious GPIO interruptsSander Vanheule2022-09-042-30/+373
| | | | | | | | | | | | | 8 and 16 bit writes to the GPIO peripheral are apparently not supported, and only worked most of the time. This resulted in garbabe writes to the interrupt mask registers, causing spurious unhandled interrupts, which could lead to CPU lock-ups as these kept retriggering. Instead of clearing these spurious interrupt when they occur, the upstream patch will just make sure all register writes have the intended result, so these don't happen at all. Signed-off-by: Sander Vanheule <sander@svanheule.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-28 17:44:28 +0000