aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* kernel: bump 5.15 to 5.15.114John Audia2023-06-031-1/+1
| | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 223004b4d6e5d17c0ae99e15d0f4c591676b4f44)
* kernel: Set CONFIG_FRAME_WARN depending on targetHauke Mehrtens2023-06-025-5/+0
| | | | | | | | | This set the CONFIG_FRAME_WARN option depending on some target settings. It will use the default from the upstream kernel and not the hard coded value of 1024 now. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 16a20512d852f6ecebf8c57cd7fa2572a06a9d0b)
* ipq40xx: e2600ac-c1 remove KERNEL_SIZE张 鹏2023-05-311-2/+0
| | | | | | | | | | Currently, e2600ac-c1 cannot be built as the kernel is larger than the defined KERNEL_SIZE, however, there is no bootloader limit for the kernel size so remove KERNEL_SIZE completely. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ improve commit title, fix merge conflict ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit b764268acb7ed410d1d81e783f1b0ce407efda82)
* ipq40xx: add e2600ac c2 to dsa张 鹏2023-05-313-2/+44
| | | | | | | | | Convert E2600ac c2 to DSA and enable it. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ rename port to more generic name ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit 0dca52cf595cedcabec5d384ddc83f1954cca46d)
* ipq40xx: add e2600ac c1 to dsa张 鹏2023-05-313-2/+36
| | | | | | | | | Convert E2600ac c1 to DSA and enable it. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ rename port to more generic name ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit 7f2ecab0f4623e9b437b1a6656275695ac063fe4)
* airoha: spi-en7523: Fix compile warningHauke Mehrtens2023-05-311-1/+3
| | | | | | | | The set_spi_clock_speed() function is not used, this causes a compile warning which results in a build error with -WError. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 2d5f3b3c4ce4c6221299f2362b3029783048f649)
* x86: disable CONFIG_X86_PLATFORM_DRIVERS_HPJohn Audia2023-05-291-0/+1
| | | | | | | New config option defaulted to N for this bump. Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 3664c57e34454ce50ac7ab6de9e3983a86cde052)
* ramips: correct page read return value of the mt7621 nand driverShiji Yang2023-05-291-5/+9
| | | | | | | | | | | | | | read_page() need to return maximum number of bitflips instead of the accumulated number. Change takes from upstream mt7621 u-boot [1]. * @read_page: function to read a page according to the ECC generator * requirements; returns maximum number of bitflips * corrected in any single ECC step, -EIO hw error [1] https://lore.kernel.org/all/cover.1653015383.git.weijie.gao@mediatek.com/ Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit 2fbb91d73ffecc7d033e5bb0b550d664ef9e0f91)
* base-files: x86 fix 01_leds Syntax errorStan Grishin2023-05-291-1/+1
| | | | | | | | | | | | Cezary Jackiewicz reported: | Syntax error in line /etc/board.d/01_leds#L22 - missing "\" Fixes: c191c2d46f00 ("x86: base-files add support for Sophos 135r3/135r3w") Reported-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Stan Grishin <stangri@melmac.ca> (buffed up commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 4b8b2f4f978d6df586dd7ce4dcc3e1286b93bd48)
* layerscape: kernel: enable MC userspace supportPawel Dembicki2023-05-291-1/+1
| | | | | | | | | | | | | | | | | | | | | Management Complex (MC) userspace support is required for userspace helpers working with DPAA2 objects exported by the Management Complex BUS. Without it, there is the error: ``` root@OpenWrt:/# ls-addni dpmac.1 error: Did not find a device file Restool wrapper scripts only support the latest major MC version that currently is MC10.x. Use with caution. error: Did not find a device file ``` This patch fixes it. Suggested-by: Alexandra Alth <alexandra@alth.de> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (cherry picked from commit d04d6a82da70f6b691409972ffd4503f339105b7)
* mediatek: sync MT7988 USXGMII with SDK driverDaniel Golle2023-05-293-596/+792
| | | | | | | | | | The USXGMII driver in SDK was heavily refactored, some bugs have been fixed and it has switched to use phylink_pcs. Follow up with changes in SDK driver and sync our on-top-of-mainline driver with the SDK driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit ba58245e83714de5f47b4b0fc0369930c3661cab)
* mediatek: follow-up with renamed Build/bl2 and Build/bl31-ubootDaniel Golle2023-05-291-6/+6
| | | | | | | | | | Use renamed build step names for all boards which were not handled by commit c620409d58 ("mediatek: filogic: add uboot build for mt7981") and now breaking the build. Fixes: c620409d58 ("mediatek: filogic: add uboot build for mt7981") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 037ce27244b52fe4c0e2bd15f4a16973c64df93f)
* mediatek: filogic: add Qihoo 360T7 supportChukun Pan2023-05-295-0/+267
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: ESMT F50L1G41LB 128MB RAM: MT5CC128M16JR-EK 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, WPS Power: DC 12V 1A Flash instructions: 1. Attach UART, boot the stock firmware until the message about failsafe mode appears. 2. Enter failsafe mode by pressing "f" and "Enter" 3. Type "mount_root", then run "fw_setenv bootmenu_delay 3" 4. Back up all mtd partitions before flashing. 5. Reboot, U-Boot now presents a menu. 6. Connect to your PC via the Gigabit port of the router, set a static ip on the ethernet interface of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 7. Select "Upgrade ATF BL2", then use this file: openwrt-mediatek-filogic-qihoo_360t7-preloader.bin 8. Select "Upgrade ATF FIP", then use this file: openwrt-mediatek-filogic-qihoo_360t7-bl31-uboot.fip 9. Download the initramfs image, and type "reset", waiting for tftp recovery to complete. a. After openwrt boots up, perform sysupgrade. Note: 1. Since NMBM is disabled, we must back up all partitions. 2. Flash instructions is based on commit 28df7f7. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (cherry picked from commit dc2d4d73939c3d86a8e9d968c5c3462f92771bc6) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: filogic: add uboot build for mt7981Chukun Pan2023-05-291-16/+24
| | | | | | | | Rename previous uboot build to mt7986-*. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (cherry picked from commit c620409d58a29d49ceccf838e90e030610c06611) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7981: add reserved memory to support pstoreAlexander Couzens2023-05-291-0/+7
| | | | | | | | | | Add reserved memory for pstore/ramoops to device tree used by Linux as well as U-Boot. Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 3eb354f999a3687f9ae547899b0f5ec2b10185ab) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: cleanly backport and add fix for I2C driverDaniel Golle2023-05-2918-81/+1684
| | | | | | | | | | Pick accepted patches from upstream Linux tree instead of having to maintain our slightly different downstream patches. Import pending patch fixing I2C on MT7981 by making sure all clocks are enabled before accessing I2C registers. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 213b7282760506ffab9151a20347d65ea70ed916)
* ramips: mark patches accepted upstreamNick Hainke2023-05-299-0/+0
| | | | | | | | Add kernel tags to the patches that got accepted upstream. Signed-off-by: Nick Hainke <vincent@systemli.org> (cherry picked from commit 2388b119de9279d7adaa525c7ba502fcae1fe187) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: fix, clean and unify SD card image generationDaniel Golle2023-05-293-9/+13
| | | | | | | | Make sure sub-images on the SD card are size-checked, allow generating SD card without squashfs and/or initramfs. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 43d27b02522c100b0c625d4b22f4bb6ad83c166f)
* kernel: bump 5.15 to 5.15.113John Audia2023-05-2915-39/+39
| | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit c815ecdebd77c3484f2cd0ef21e4c69d274ef33a)
* generic: filter out CONFIG_PAHOLE_HAS_SPLIT_BTFRobert Marko2023-05-251-0/+1
| | | | | | | | | CONFIG_PAHOLE_HAS_SPLIT_BTF should be runtime detected as it depends on pahole being available on the host, so filter it out of configs. Signed-off-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit 3591353f5143fc46e31f921484177a9d6f1089a2) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add basic mt7988 device tree supportSam Shih2023-05-247-0/+1320
| | | | | | | | This add basic device tree support for mediatek MT7988 SoC Signed-off-by: Sam Shih <sam.shih@mediatek.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit e3a681bab4b2c193704e76b8a6091e57f0fab14e)
* mediatek: backport cpufreq changes to support MT7988Daniel Golle2023-05-2422-0/+2178
| | | | | | | | Backport cpufreq changes from upstream so that the MediaTek MT7988 SoC can be supported. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit e4555d69a1c7c811188d8e257e77ac917d15f492)
* mediatek: filogic: add driver for Richtek RT5190A regulatorDaniel Golle2023-05-245-1/+746
| | | | | | | | | The Richtek RT5190A is used on the MT7988 reference board. Backport and enable the driver on the filogic subtarget, so we can support cpufreq on the MT7988 reference board. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit a3cf3e2c489d5b6f534d1b4d6f7b462f81c9c141)
* mediatek: add driver for built-in 2.5G Ethernet PHYDaniel Golle2023-05-244-0/+303
| | | | | | | | | Add driver for the built-in 2.5G Ethernet PHY found in the MT7988 SoC. To function the PHY also needs firmware files which have not yet been published via linux-firmware. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit ef2a831dabacfda6c36c79b8f963b5fdd9b2d080)
* mediatek: update pending SoC Ethernet PHY driverDaniel Golle2023-05-247-1399/+1301
| | | | | | | | Update driver for MediaTek's built-in Gigabit Ethernet PHYs which can be found in the MT7981 and MT7988 SoCs. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 987a0b2b3011a9e5ee3e4120b068fb2f113628a7)
* generic: mt7530: backport support for the MT7988 built-in switchDaniel Golle2023-05-2426-9/+2493
| | | | | | | | | | | | | | | | | Backport commits adding support for the MT7988 built-in switch to the mt7530 driver. This change results in the Kconfig symbol NET_DSA_MT7530 to be extended by NET_DSA_MT7530_MDIO (everything formally covered by NET_DSA_MT7530) and NET_DSA_MT7530_MMIO (a new driver for the MMIO-connected built-in switch of the MT7988 SoC). Select NET_DSA_MT7530_MDIO for all targets previously selecting NET_DSA_MT7530, with the exception of mediatek/filogic which also selects NET_DSA_MT7530_MMIO. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 958fdf36e35c814eb83faf2c39db4ca379c921b5)
* generic: add support for MediaTek NETSYS v3Daniel Golle2023-05-2411-6/+3220
| | | | | | | | In order to support Ethernet on the MT7988 SoC add support for NETSYS v3 as well as new paths and USXGMII SerDes to the mtk_eth_soc driver. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 6983a215d9d1966f95bc5b1c0045c200948b2079)
* mediatek: add mt7988 pinctrl driver supportSam Shih2023-05-244-0/+1309
| | | | | | | | This adds provisional pinctrl driver support for the MediaTek MT7988 SoC. Signed-off-by: Sam Shih <sam.shih@mediatek.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 9e6a7e808f2e9dd02733ccc41827940fb421091d)
* mediatek: add mt7988 clock drivers supportSam Shih2023-05-2411-0/+1668
| | | | | | | | This adds clock drivers for the MediaTek MT7988 SoC Signed-off-by: Sam Shih <sam.shih@mediatek.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit b33c1858767e5109913ac2195ec2b2b8ef0e726a)
* mediatek: mt7981: setup all clocks needed for eMMCDaniel Golle2023-05-241-4/+5
| | | | | | | | Setup all necessary clocks to get MMC to work on MT7981, similar to how it is done also on MT7986. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit a9989b30d01e534288928d7ef48df3eb9fe3150b)
* mediatek: mt7981: usb enable 3.0 by defaultChukun Pan2023-05-241-1/+0
| | | | | | | | | There is no reason to limit USB to 2.0 mode by default, delete this limit. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (cherry picked from commit b2beb4c68849c804a8b9441f776a6918d433fb1e) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: enable (ARM|ARM64)_MODULE_PLTS in generic configTony Ambardar2023-05-2410-11/+2
| | | | | | | | | | | | | | | | | | | | | This allows loading modules with large memory requirements, recently needed while testing on armvirt/32. Past forum discussions [1] and bug reports [2] also raised this and the ipq806x target already set it in response [3]. Given this increases kernel image size by only ~1KB, is generally useful on multi-platform kernels, and enabled by default on upstream arm32 Linux, add it to the generic config. The setting has similar utility on arm64, is a requirement for KASLR, and already enabled on most OpenWrt aarch64 targets, so pull this into the top-level generic config. [1]: https://forum.openwrt.org/t/vmap-allocation-for-size-442368-failed-use-vmalloc-size-to-increase-size/34545/7 [2]: https://github.com/openwrt/openwrt/issues/8282 [3]: f81e148eb6 ("ipq806x: update 4.19 kernel config"). Signed-off-by: Tony Ambardar <itugrok@yahoo.com> (cherry picked from commit c2d194a34eb1a62a610f0437287db6c3eca64d5a) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: build SD card without all filesystemsDaniel Golle2023-05-241-0/+8
| | | | | | | | | Allow building SD card images without having both initramfs and squashfs present on the card, just like it has already been done for the mt7622 and filogic subtargets. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit d6fef27f2dd4a852ed7846e4aa5f06dcd8df91b6)
* mediatek: add support for Zyxel EX5601-T0 routerPietro Ameruoso2023-05-243-0/+587
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zyxel EX5601-T0 specifics -------------- The operator specific firmware running on the Zyxel branded EX5601-T0 includes U-Boot modifications affecting the OpenWrt installation. Partition Table | dev | size | erasesize | name | | ---- | -------- | --------- | ------------- | | mtd0 | 20000000 | 00040000 | "spi0.1" | | mtd1 | 00100000 | 00040000 | "BL2" | | mtd2 | 00080000 | 00040000 | "u-boot-env" | | mtd3 | 00200000 | 00040000 | "Factory" | | mtd4 | 001c0000 | 00040000 | "FIP" | | mtd5 | 00040000 | 00040000 | "zloader" | | mtd6 | 04000000 | 00040000 | "ubi" | | mtd7 | 04000000 | 00040000 | "ubi2" | | mtd8 | 15a80000 | 00040000 | "zyubi" | The router boots BL2 which than loads FIP (u-boot). U-boot has hardcoded a command to always launch Zloader "mtd read zloader 0x46000000" and than "bootm". Bootargs are deactivated. Zloader is the zyxel booloader which allow to dual-boot ubi or ubi2, by default access to zloader is blocked. Too zloader checks that the firmware contains a particolar file called zyfwinfo. Additional details regarding Zloader can be found here: https://hack-gpon.github.io/zyxel/ https://forum.openwrt.org/t/adding-openwrt-support-for-zyxel-ex5601-t0/155914 Hardware -------- SOC: MediaTek MT7986a CPU: 4 core cortex-a53 (2000MHz) RAM: 1GB DDR4 FLASH: 512MB SPI-NAND (Micron xxx) WIFI: Wifi6 Mediatek MT7976 802.11ax 5 GHz 4x4 + 2.4GHZ 4x4 ETH: MediaTek MT7531 Switch + SoC 3 x builtin 1G phy (lan1, lan2, lan3) 1 x MaxLinear GPY211B 2.5 N-Base-T phy5 (lan4) 1 x MaxLinear GPY211B 2.5Gbit xor SFP/N-Base-T phy6 (wan) USB: 1 x USB 3.2 Enhanced SuperSpeed port UART: 3V3 115200 8N1 (Pinout: GND KEY RX TX VCC) VOIP: 2 FXS ports for analog phones MAC Address Table ----------------- eth0/lan Factory 0x002a eth1/wan Factory 0x0024 wifi 2.4Ghz Factory 0x0004 wifi 5Ghz Factory 0x0004 + 1 Serial console (UART) --------------------- +-------+-------+-------+-------+-------+ | +3.3V | RX | TX | KEY | GND | +---+---+-------+-------+-------+-------+ | +--- Don't connect Installation ------------ Keep in mind that openwrt can only run on the UBI partition, the openwrt firmware is not able to understand the zloader bootargs. The procedure allows restoring the UBI partition with the Zyxel firmware and retains all the OEM functionalities. 1. Unlock Zloader (this will allow to swap manually between partitions UBI and UBI2): - Attach a usb-ttl adapter to your computer and boot the router. - While the router is booting at some point you will read the following: `Please press Enter to activate this console.` - As soon as you read that press enter, type root and than press enter again (just do it, don't care about the logs scrolling). - Most likely the router is still printing the boot log, leave it boot until it stops. - If everything went ok you should have full root access "root@EX5601-T0:/#". - Type the following command and press enter: "fw_setenv EngDebugFlag 0x1". - Reboot the router. - As soon as you read `Hit any key to stop autoboot:` press Enter. - If everything went ok you should have the following prompt: "ZHAL>". - You have successfully unlocked zloader access, this procedure must be done only once. 2. Check the current active partition: - Boot the router and repeat the steps above to gain root access. - Type the following command to check the current active image: "cat /proc/cmdline". - If `rootubi=ubi` it means that the active partition is `mtd6` - If `rootubi=ubi2` it means that the active partition is `mtd7` - As mentioned earlier we need to flash openwrt into ubi/mtd6 and never overwrite ubi2/mtd7 to be able to fully roll-back. - To activate and boot from mtd7 (ubi2) enter into ZHAL> command prompt and type the following commands: atbt 1 # unlock write atsw # swap boot partition atsr # reboot the router - After rebooting check again with "cat /proc/cmdline" that you are correctly booting from mtd7/ubi2 - If yes proceed with the installation guide. If not probably you don't have a firmware into ubi2 or you did something wrong. 3. Flashing: - Download the sysupgrade file for the router from openwrt, than we need to add the zyfwinfo file into the sysupgrade tar. Zloader only checks for the magic (which is a fixed value 'EXYZ') and the crc of the file itself (256bytes). I created a script to create a valid zyfwinfo file but you can use anything that does exactly the same: https://raw.githubusercontent.com/pameruoso/OpenWRT-Zyxel-EX5601-T0/main/gen_zyfwinfo.sh - Add the zyfwinfo file into the sysupgrade tar. - Enter via telnet or ssh into the router with admin credentials - Enter the following commands to disable the firmware and model checks "zycli fwidcheck off" and "zycli modelcheck off" - Open the router web interface and in the update firmware page select the "restore default settings option" - Select the sysupgrade file and click on upload. - The router will flash and reboot itself into openwrt from UBI 4. Restoring and going back to Zyxel firmware. - Use the ZHAL> command line to manually swap the boot parition to UBI2 with the following: atbt 1 # unlock write atsw # swap boot partition atsr # reboot the router - You will boot again the Zyxel firmware you have into UBI2 and you can flash the zyxel firmware to overwrite the UBI partition and openwrt. Working features ---------------- 3 gbit lan ports Wifi Zyxel partitioning for coexistance with Zloader and dual boot. WAN SFP port (only after exporting pins 57 and 10. gpiobase411) leds reset button serial interface usb port lan ethernet 2.5 gbit port (autosense) wan ethernet 2.5 gbit port (autosense) Not working ---------------- voip (missing drivers or proper zyxel platform software) Swapping the wan ethernet/sfp xor port ---------------- The way to swap the wan port between sfp and ethernet is the following: export the pins 57 and 10. Pin 57 is used to probe if an sfp is present. If pin 57 value is 0 it means that an sfp is present into the cage (cat /sys/class/gpio/gpio468/value). If pin 57 value is 1 it means that no sfp is inserted into the cage. In conclusion by default both 57 an 10 pins are by default 1, which means that the active port is the ethernet one. After inserting an SFP pin 57 will become 0 and you have to manually change the value of pin 10 to 0 too. This is totally scriptable of course. Leds description ------------ All the leds are working out of the box but the leds managed by the 2 maxlinear phy (phy 5 lan, phy6 wan). To activate the phy5 led (rj45 ethernet port led on the back of the router) you have to use mdio-tools. To activate the phy6 led (led on the front of the router for 2.5gbit link) you have to use mdio-tools. Example: Set lan5 led to fast blink on 2500/1000, slow blink on 10/100: mdio mdio-bus mmd 5:30 raw 0x0001 0x33FC Set wan 2.5gbit led to constant on when wan is 2.5gbit: mdio mdio-bus mmd 6:30 raw 0x0001 0x0080 Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it> (cherry picked from commit 1c05388ab04c934ec240e8362321908f91381a90) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add support for D-Link DIR-859 A3Shiji Yang2023-05-246-4/+87
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: QCA9563 775 MHz + QCA9880 Switch: QCA8337N-AL3C RAM: Winbond W9751G6KB-25 64 MiB Flash: Winbond W25Q128FVSG 16 MiB WLAN: Wi-Fi4 2.4 GHz 3*3 + 5 GHz 3*3 LAN: LAN ports *4 WAN: WAN port *1 Buttons: reset *1 + wps *1 LEDs: ethernet *5, power, wlan, wps MAC Address: use address source1 source2 label 40:9b:xx:xx:xx:3c lan && wlan u-boot,env@ethaddr lan 40:9b:xx:xx:xx:3c devdata@0x3f $label wan 40:9b:xx:xx:xx:3f devdata@0x8f $label + 3 wlan2g 40:9b:xx:xx:xx:3c devdata@0x5b $label wlan5g 40:9b:xx:xx:xx:3e devdata@0x76 $label + 2 Install via Web UI: Apply factory image in the stock firmware's Web UI. Install via Emergency Room Mode: DIR-859 A1 will enter recovery mode when the system fails to boot or press reset button for about 10 seconds. First, set computer IP to 192.168.0.5 and Gateway to 192.168.0.1. Then we can open http://192.168.0.1 in the web browser to upload OpenWrt factory image or stock firmware. Some modern browsers may need to turn on compatibility mode. Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit 0ffbef9317a1dc049ad259c1ec1530355efc0552) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: improve support for D-Link DIR-8x9 A1 seriesShiji Yang2023-05-244-10/+9
| | | | | | | | | | | | | | | | 1. Remove unnecessary new lines in the dts. 2. Remove duplicate included file "gpio.h" in the device dts. 3. Add missing button labels "reset" and "wps". 4. Unify the format of the reg properties. 5. Add u-boot environment support. 6. Reduce spi clock frequency since the max value suggested by the chip datasheet is only 25 MHz. 7. Add seama header fixup for DIR-859 A1. Without this header fixup, u-boot checksum for kernel will fail after the first boot. Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit e5d8739aa846db621b6368ba83db17c353a35dea) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: enable NVMEM u-boot-env driver on generic subtargetINAGAKI Hiroshi2023-05-241-0/+2
| | | | | | | | | This patch enables NVMEM u-boot-env driver (COFNIG_NVMEM_U_BOOT_ENV) on generic subtarget to use from devices, for MAC address and etc. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (cherry picked from commit e8f7957450e2dcbeb90492c711a973d2cf0ebbfc) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uml: fix build error due to frame size > 1024Christian Lamparter2023-05-241-10/+14
| | | | | | | | | | | | | | | | | | | | | the UML build fails during the kernel build: | arch/um/drivers/net_kern.c: In function 'compute_hash': | arch/um/drivers/net_kern.c:322:1: error: the frame size of 1072 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] | 322 | } | | ^ |cc1: all warnings being treated as errors The compute_hash() function is added by our patch: 102-pseudo-random-mac.patch Instead of allocating a 1024 byte buffer on the stack for the SHA1 digest input, let's allocate the data on the heap. We should be able to do that since crypto_alloc_ahash and ahash_request_alloc also need to allocate structures on the heap. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit aed2569d3780cab1a1a2d75c9f9e3fe413a9844d) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* treewide: Disable building 8M RAM devicesFelix Baumann2023-05-211-0/+1
| | | | | | | | Following deprecation notice[1] in 21.02, disable target with 8M of RAM [1] https://openwrt.org/supported_devices/864_warning Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* treewide: Disable building 32M RAM devicesFelix Baumann2023-05-2116-0/+124
| | | | | | | | Following deprecation notice[1] in 21.02, disable targets with 32M of RAM [1] https://openwrt.org/supported_devices/864_warning Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* treewide: Disable building 16M RAM devicesFelix Baumann2023-05-212-0/+29
| | | | | | | | Following deprecation notice[1] in 21.02, disable targets with 16M of RAM [1] https://openwrt.org/supported_devices/864_warning Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: mt7621: fix Xiaomi Router 3G/Pro LEDsDENG Qingfang2023-05-202-20/+53
| | | | | | | | | | The PHY name has been changed to "mt7530-0" since IRQ support was added to MT7530 driver. Fixes: f9cfe7af1f1f ("kernel: backport MT7530 IRQ support") Signed-off-by: DENG Qingfang <dqfext@gmail.com> (node names, added color, function+function-enumerator properties) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: base-files add support for Sophos 135r3/135r3wStan Grishin2023-05-202-0/+11
| | | | | | | | | | | | | | The Sophos SG/XG-135 revision 3 has odd numbering of eth ports where the WAN port (as marked on the case) is: `eth6` and `eth0`, `eth1`, `eth2`, `eth3`, `eth5`, `eth7`, `eth8` are LAN ports. Port `eth4` seems to be the SFP port. Also add the missing LED definition for supported Sophos devices. Original discussion at: https://forum.openwrt.org/t/openwrt-on-revision-3-of-sophos-desktop-appliances/152912 Signed-off-by: Stan Grishin <stangri@melmac.ca>
* kirkwood: add support for Iomega Storcenter ix4-200dSander van Deijck2023-05-203-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Iomega Storcenter ix4-200d is a four-bay SATA NAS powered by a Marvell Kirkwood SoC clocked at 1.2GHz. It has 512MB of RAM and 32MB of flash memory, 3x USB 2.0 and 2x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1200Mhz - Flash size: 32 MiB - RAM: 512MB - LAN: 2x 1Gbit/s - 3x USB 2.0 Notes: - The blue drive LED is triggered by HDD activity, it can not be controlled via GPIO. - The LCD screen requires proprietary code and does not function at this time. - Due to a kernel-related issue with the Marvell 88SE6121 SATA controller, currently only trays numbered #3 and #4 work, #1 and #2 do not. [1] Serial pinout: CN4 -------------- | 10 8 6 4 2 | | 9 7 5 3 1 | -------------- PIN 1 Mark (fat line) 1 = RXD 4 = TXD 6 = GND 9 = 3.3V (not necessary to connect) Installation instructions: 1. download initramfs-uImage and copy into tftp server 2. connect the tftp server to network port #1 3. access uboot environment with serial cable and run setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.2 tftpboot 0x00800000 [initramfs-uImage filename] bootm 0x00800000 4. connect to LAN on network port #2, log into openwrt and sysupgrade to install into flash [1] https://bugzilla.kernel.org/show_bug.cgi?id=216094 Signed-off-by: Sander van Deijck <sander@vandeijck.com> (aligned FROM from signed-off. LED+key rename, whitespace removal) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: remove obsolete kernel version switchesAleksander Jan Bajkowski2023-05-2012-154/+0
| | | | | | | This removes unneeded kernel version switches from the targets after kernel 5.10 has been dropped. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* kernel: net: add support for kernel tlsTiago Gaspar2023-05-201-0/+2
| | | | | | | | | | Add ktls (Kernel TLS) kmods to enable TLS support in kernel (allowing TLS offload when the network card supports it) Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com> (added disabled symbols) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: convert EZVIZ CS-W3-WD1200G-EUP to DSAChristian Lamparter2023-05-203-2/+38
| | | | | | Convert the repeater to DSA. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: fix 5GHz on QCA9886 variant of ZTE MF286Lech Perczak2023-05-202-4/+4
| | | | | | | | | | | Recently, a strange variant of ZTE MF286 was discovered, having QCA9886 radio instead of QCA9882 - like MF286A, but having MF286 flash layout and rest of hardware. To support both variants in one image, bind calibration data at offset 0x5000 both as "calibration" and "pre-calibration" nvmem-cells, so ath10k can load caldata for both at runtime. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: Add support for D-Link DIR-869-A1Jan Forman2023-05-204-1/+51
| | | | | | | | | | | | | | | | | | | | Specifications The D-Link EXO AC1750 (DIR-869) router released in 2016. It is powered by Qualcomm Atheros QCA9563 @ 750 MHz chipset, 64 MB RAM and 16 MB flash. 10/100/1000 Gigabit Ethernet WAN port Four 10/100/1000 Gigabit Ethernet LAN ports Power Button, Reset Button, WPS Button, Mode Switch Flashing 1. Upload factory.bin via D-link web interface (Management/Upgrade). Revert to stock Upload original firmware via OpenWrt sysupgrade interface. Debricking D-Link Recovery GUI (192.168.0.1) Signed-off-by: Jan Forman <forman.jan96@gmail.com>
* ath79: Convert calibration data to nvmemJan Forman2023-05-203-7/+35
| | | | | | | | | For D-link DIR-859 and DIR-869 Replace the mtd-cal-data by an nvmem-cell. Add the PCIe node for the ath10k radio to the devicetree. Thanks to DragonBlue for this patch Signed-off-by: Jan Forman <jforman@tuta.io>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-13 12:22:12 +0000