aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* apm821xx: align gpio-keys node names with dt-schemaChristian Lamparter2022-06-195-8/+8
| | | | | | | | | | | | As per the series: <https://www.spinics.net/lists/devicetree/msg508906.html> "Enforce specific naming pattern for children (keys) to narrow the pattern thus do not match other properties. This will require all children to be properly prefixed or suffixed (button, event, switch or key)." Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* lantiq: dts: Add the reset line for the PCI controllerMartin Blumenstingl2022-06-193-0/+6
| | | | | | | The PCI controller has it's reset line wired up to bit 13 of RCU. Describe this in our .dtsi files. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* ath79: add support for Netgear PGZNG1Chris Blake2022-06-195-0/+378
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear PGZNG1, also known as the ADT Pulse Gateway. Hardware: CPU: Atheros AR9344 Memory: 256MB Storage: 256MB NAND Hynix H27U2G8F2CTR-BC USB: 1x USB 2.0 Ethernet: 2x 100Mb/s WiFi: Atheros AR9340 2.4GHz 2T2R Leds: 8 LEDs Button: 1x Reset Button UART: Header marked JPE1. Pinout is VCC, TX, RX, GND. The marked pin, closest to the JPE1 marking, is VCC. Note VCC isn't required to be connected for UART to work. Enable Stock Firmware Shell Access: 1. Interrupt u-boot and run the following commands setenv console_mode 1 saveenv reset This will enable a UART shell in the firmware. You can then login using the root password of `icontrol`. If that doesn't work, the device is running a firmware based on OpenWRT where you can drop into failsafe to mount the FS and then modify /etc/passwd. Installation Instructions: 1. Interupt u-boot and run the following commands setenv active_image 0 setenv stock_bootcmd nboot 0x81000000 0 \${kernel_offset} setenv openwrt_bootcmd nboot 0x82000000 0 \${kernel_offset} setenv bootcmd run openwrt_bootcmd saveenv 2. boot initramfs image via TFTP u-boot tftpboot 0x82000000 openwrt-ath79-nand-netgear_pgzng1-initramfs-kernel.bin; bootm 0x82000000 3. Once booted, use LuCI sysupgrade to flash openwrt-ath79-nand-netgear_pgzng1-squashfs-sysupgrade.bin MAC Table: WAN (eth0): xx:xa - caldata 0x0 LAN (eth1): xx:xb - caldata 0x6 WLAN (phy0): xx:xc - burned into ath9k caldata Not Working: Z-Wave RS422 Signed-off-by: Chris Blake <chrisrblake93@gmail.com> (added more hw-info, fixed file permissions) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: add upstream patches for pca955x led driverChris Blake2022-06-195-0/+582
| | | | | | | | These patches are to support the pca955x led with OpenWRT correctly via device tree on linux 5.10. Without these, the new LED function/color/reg features can not be used. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* mpc85xx: p2020: add RTC ds1307 to kernelJosef Schlehofer2022-06-191-0/+1
| | | | | | | | | | | | | | If the RTC module is compiled as a module, the hctosys fails to initialize because ds1307 is loaded later. Fixes: [ 2.004145] hctosys: unable to open rtc device (rtc0) [ 11.957997] rtc-ds1307 0-006f: registered as rtc0 This is similar to commit 5481ce9a1157a43d8b2c963e03fb243e70974361, which was done for imx6 target. Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* ipq40xx: add support for Meraki MR74Matthew Hagan2022-06-1911-409/+452
| | | | | | | | | | | | The Meraki MR74 is part of the "Insect" series. This device is essentially an outdoor variant of the MR33 with identical hardware, but requiring a config@3 DTS option to be set to allow booting with the stock u-boot. The install procedure is replicated from the MR33, with the exception being that the MR74 sysupgrade image must be used. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* apm821xx: MBL: make mtd chip workChristian Lamparter2022-06-193-2/+7
| | | | | | | | | | | | | | | | The MBL has a 512KiB Microchip SST39VF040 chip for uboot and not much else. Thanks to Ewald who figured out that the "jedec-probe" vs. "jedec-flash" was the wrong binding. With this information and the jedec-probe support enabled => the chip works. | physmap-flash 4fff80000.nor_flash: physmap platform flash device: [mem 0x4fff80000-0x4ffffffff] | Found: SST 39LF040 | 4fff80000.nor_flash: Found 1 x8 devices at 0x0 in 8-bit bank Suggested-by: Ewald Comhaire <e.comhaire@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: enable NAND support for all subtargetsJosef Schlehofer2022-06-193-3/+1
| | | | | | | | | | | | | | In subtarget p2020, there wasn't enabled nand support, and because of that there weren't available tools from mtd-utils package, which has utilities for NAND flash memory even though reference board, which is the only currently supported device in p2020 subtarget has NAND [1]. All subtargets in mpc85xx has already enabled nand support, let's do it globally. [1] https://www.nxp.com/design/qoriq-developer-resources/p2020-reference-design-board:P2020RDB Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* kernel: Backport mv88e6xxx patch to keep pvid at 0 if VLAN-unaware and ↵Marek Behún2022-06-191-18/+0
| | | | | | | | | | | | | | | remove hack Keeping the pvid at 0 when VLAN-unaware makes it possible to drop the hack introduced in commit 920eaab1d817 ("kernel: DSA roaming fix for Marvell mv88e6xxx"). Dropping the hack makes it possible to use VLAN interfaces with VID 1 on DSA ports without problems with FDB. Signed-off-by: Marek Behún <kabel@kernel.org> (cherry picked from commit 9caa6f0aa742253901c72f43eebecd2c8da5f127) Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [drop kernel patch hack from Linux version 5.15, drop paragraph about backport patch, which is not necessary as it is included in kernel 5.15]
* bcm53xx: remove 07_set_preinit_iface_bcm53xxChristian Lamparter2022-06-191-14/+0
| | | | | | | | with the switch to DSA setup, the switch gets correctly programmed via the device-tree now. This hack is no longer necessary. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: move Toshiba-TC58NVG0S3H patch to ipq40xx reduxChristian Lamparter2022-06-192-12/+6
| | | | | | | | | | | | | | | | | | Linux' upstream MTD-Maintainer Miquèl Raynal noted: |Reverting seems the safest option here, not knowing how many devices |have these damaged/counterfeit chips. If it is just a couple and only on |Fritzboxes, as suggested in the Github issue this patch could be |carried through OpenWrt and that would seem more future proof IMHO. This patch follows up with the first patch. It actually moves the patches out of target/linux/generic/pending into the ipq40xx's patch heap and adds a little note what happend. For more information, discussions or reports about bad TC58NVG0S3Hs, please visit the OpenWrt's Github Issue #9962: <https://github.com/openwrt/openwrt/issues/9962> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* realtek: add support for power LED on Netgear GS108Tv3Pascal Ernster2022-06-191-0/+27
| | | | | | | | | | | | | | | | | | | | | The Netgear GS108Tv3 is already supported by OpenWrt, but is missing LED support. After OpenWrt installation, all LEDs are off which makes the installation quite confusing. This enables support for the green/amber power LED to give feedback about the current status. This is basically just a verbatim copy of commit c4927747d25a ("realtek: add support for power LED on Netgear GS308Tv1"). Please note that both LEDs are wired up in an anti-parallel fashion, which means that only one of both LEDs/colors can be switched on at the same time. If both LEDs/colors are switched on simultanously, the LED goes dark. Tested-by: Pascal Ernster <git@hardfalcon.net> Signed-off-by: Pascal Ernster <git@hardfalcon.net> [add title to commit reference] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: add support for D-Link DGS-1210-20Markus Stockhausen2022-06-192-0/+110
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash * 16 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - External PHY with 8 ports (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [o]ooo|J6 | ||`------ GND | |`------- RX | `-------- TX `---------- Vcc (3V3) Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl838x-d-link_dgs-1210-20-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de> [correct initramfs image name] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* rockchip: add kernel 5.15 as testingJuergen Wurzer2022-06-186-1/+763
| | | | | | | | Add kernel 5.15 as testing kernel for the rockchip-armv8 target. Signed-off-by: Juergen Wurzer <wurzer.juergen@gmail.com> [squash commits, update commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix RT-AC57U button levelDavid Bauer2022-06-181-1/+1
| | | | | | | Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the WPS cutton to fix button behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: TP-Link EAP225 v3: use pre-calibration nvmem-cellSander Vanheule2022-06-181-3/+3
| | | | | | | | | ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Rename the nvmem cell node and label to match the updated cell name. Fixes: eca0d7301198 ("ath79: TP-Link EAP225 v3: convert ath10k to nvmem-cells") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Wall v2: use pre-calibration nvmem-cellSander Vanheule2022-06-181-3/+3
| | | | | | | | | ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Rename the nvmem cell node and label to match the updated cell name. Fixes: 48625a04453b ("ath79: TP-Link EAP225-Wall v1: convert radios to nvmem-cells") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Outdoor v1: use pre-calibration nvmem-cellNick Hainke2022-06-181-3/+3
| | | | | | | | | | | | | | | | | | | | | | Fixes errors in the form of: ath10k_pci 0000:00:00.0: failed to fetch board data for bus=pci, vendor=168c,device=0056,subsystem-vendor=0000,subsystem-device =0000 from ath10k/QCA9888/hw2.0/board-2.bin ath10k_pci 0000:00:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0 ath10k_pci 0000:00:00.0: failed to fetch board file: -12 ath10k_pci 0000:00:00.0: could not probe fw (-12) As described already in 2d3321619b2b ("ath79: TP-Link EAP245 v3: use pre-calibration nvmem-cell"): Ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Further rename the nvmem cell node and label to match the updated cell name. Fixes: 23b904074500 ("ath79: TP-Link EAP225-Outdoor v1: convert ath10k to nvmem-cells") Suggested-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: UniFi 6 LR: disable RTCDaniel Golle2022-06-181-0/+6
| | | | | | | | There is not RTC battery connected to the SoC of the UniFi 6 LR board. Disable the RTC to prevent the system coming up with time set to 2000-01-01 00:00:00 after each reboot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: D-Link DAP-2xxx (QCA953x): convert ath9k caldata to nvmemSander Vanheule2022-06-181-2/+11
| | | | | | | | | | Convert the calibration data reference for the ath9k radio to an nvmem-cell, replacing the downstream mtd-cal-data property. Since the 'art' label is no longer used, it can be dropped. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2xxx (QCA953x): move art partition to DTSISander Vanheule2022-06-183-12/+6
| | | | | | | | | The art partition containing the radio calibration data is in the same location for all supported devices. Move the definition to the base file so the reference from the wmac node can reference the same file. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-3662 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-9/+16
| | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2695 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-3/+16
| | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2660 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-2/+15
| | | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Tested-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2680 A1: convert ath10k caldata to nvmemSander Vanheule2022-06-183-7/+20
| | | | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the pre-calibration data using nvmem-cells. MAC address assignment is moved to '10_fix_wifi_mac', so the device can then be removed from the caldata extraction script '11-ath10k-caldata'. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Tested-by: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2xxx (QCA955x): convert ath9k caldata to nvmemSander Vanheule2022-06-181-1/+10
| | | | | | | | Convert the calibration data reference for the ath9k radio to an nvmem-cell, replacing the downstream mtd-cal-data property. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: D-Link DAP-2xxx (QCA955x): move art partition to DTSISander Vanheule2022-06-185-24/+6
| | | | | | | | | The art partition containing the radio calibration data is in the same location for all supported devices. Move the definition to the base file so the reference from the wmac node can refer to the same file. Cc: Sebastian Schaper <openwrt@sebastianschaper.net> Signed-off-by: Sander Vanheule <sander@svanheule.net>
* kernel: backport upstream mtk_eth_soc patchesFelix Fietkau2022-06-1828-13/+3272
| | | | | | Includes MT7986 ethernet support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: move mtk flow offload patches to backport-5.15Felix Fietkau2022-06-1812-6/+6
| | | | | | They were accepted upstream Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: TP-Link EAP245 v3: use pre-calibration nvmem-cellSander Vanheule2022-06-181-1/+1
| | | | | | | | | | ath10k Wave-2 hardware requires an nvmem-cell called "pre-calibration" to load the device specific caldata, not "calibration". Update the nvmem-cell name to make the 5GHz radio work again. Fixes: d4b3b2394233 ("ath79: TP-Link EAP245 v3: convert radios to nvmem-cells") Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: add support for power LED on Netgear GS308Tv1Andreas Böhler2022-06-181-0/+27
| | | | | | | | | | The Netgear GS308Tv1 is already supported by OpenWrt, but is missing LED support. After OpenWrt installation, all LEDs are off which makes the installation quite confusing. This enables support for the green/amber power LED to give feedback about the current status. Signed-off-by: Andreas Böhler <dev@aboehler.at>
* bcm53xx: copy bgmac revert (performance fix) to 5.15Rafał Miłecki2022-06-171-0/+33
| | | | | Ref: 230c9da963aa ("bcm53xx: revert bgmac back to the old limited max frame size") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: move ethernet phy node for TP-Link EAP devicesSander Vanheule2022-06-165-7/+48
| | | | | | | | Move the ethernet phy definition from the eap2x5-1port include to the device-specific DTS files. This is to prepare for new devices that have a different ethernet phy, at another MDIO address. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Wall v1: convert radios to nvmem-cellsSander Vanheule2022-06-162-9/+24
| | | | | | | | | | | | | Replace the mtd-cal-data phandle by an nvmem-cell reference to the art partition for the 2.4GHz ath9k radio. Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP245 v3: convert radios to nvmem-cellsSander Vanheule2022-06-162-8/+25
| | | | | | | | | | | | | Replace the mtd-cal-data phandle by an nvmem-cell reference from the art partition for the 2.4GHz ath9k radio. Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using an nvmem-cell. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225 v3: convert ath10k to nvmem-cellsSander Vanheule2022-06-162-1/+18
| | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225-Outdoor v1: convert ath10k to nvmem-cellsSander Vanheule2022-06-162-1/+18
| | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP225 v1: convert ath10k to nvmem-cellsSander Vanheule2022-06-162-7/+24
| | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: TP-Link EAP245 v1: convert ath10k to nvmem-cellsSander Vanheule2022-06-162-1/+18
| | | | | | | | | | Add the PCIe node for the ath10k radio to the devicetree, and refer to the art partition for the calibration data using nvmem-cells. Use mac-address-increment to ensure the MAC address is set correctly, and remove the device from the caldata extraction and patching script. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: convert 1-port TP-Link EAP ath9k to nvmem-cellsSander Vanheule2022-06-161-3/+10
| | | | | | | | | | | Replace the mtd-cal-data phandle with an nvmem-cell reference for the 2.4GHz ath9k radio. This affects the following devices: - TP-Link EAP225 v1 - TP-Link EAP225 v3 - TP-Link EAP225-Outdoor v1 - TP-Link EAP245 v1 Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: drop phy-mask propertySander Vanheule2022-06-1571-128/+0
| | | | | | | The phy-mask property is no longer supported by the ag71xx-mdio driver, so let's drop it. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ath79: ag71xx-mdio: remove phy-mask propertySander Vanheule2022-06-151-4/+0
| | | | | | | | | | | | | The phy-mask property is read by the ag71xx-mdio driver to set the mii_bus's phy_mask field. On OF platforms, the devicetree is expected to provide all present ethernet phy-s however, so the phy_mask field is later set to all-ones. Having a devicetree override is of no use then, so let's drop it. Cc: David Bauer <mail@david-bauer.net> Cc: John Crispin <john@phrozen.org> Signed-off-by: Sander Vanheule <sander@svanheule.net> Acked-by: David Bauer <mail@david-bauer.net>
* bcm53xx: revert bgmac back to the old limited max frame sizeRafał Miłecki2022-06-151-0/+33
| | | | | | | | | | | Bumping max frame size has significantly affected network performance. It was done by upstream commit that first appeared in the 5.7 release. This change bumps NAT masquarade speed from 196 Mb/s to 383 Mb/s for the BCM4708 SoC. Ref: f55f1dbaad33 ("bcm53xx: switch to the kernel 5.10") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* qoriq: use FIT uImage for Firebox M300 kernelStijn Tintel2022-06-141-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This requires U-Boot environment changes: setenv OpenWrt_kernel watchguard_firebox-m300-fit-uImage.itb setenv loadaddr 0x20000000 setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; mmc dev 0; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr' Trying to sysupgrade an image containing this change on an M300 already running OpenWrt will fail with the following error: Tue Jun 14 12:06:21 EEST 2022 upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n). Tue Jun 14 12:06:21 EEST 2022 upgrade: Kernel switched to FIT uImage. Update U-Boot environment. Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from bootdisk... Tue Jun 14 12:06:21 EEST 2022 upgrade: Extract boot sector from the image Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from image... Image check failed. This is to prevent rendering your device unbootable. Make the U-Boot environment changes as instruced above, and then flash the image using sysupgrade -F. The config can be kept, there is no need to use -n. After the new image booted successfully, you can increase the compat_version: uci set system.@system[0].compat_version='1.1' uci commit Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* qoriq: use KERNEL_SUFFIX in Build/sdcard-imgStijn Tintel2022-06-141-1/+1
| | | | | | | | | Use the KERNEL_SUFFIX variable in Build/sdcard-img, rather than using hardcoded "-kernel.bin", to allow overriding KERNEL_SUFFIX for a device. Fixes: 080a769b4da8 ("qoriq: new target") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: add support for MTS WG430223Mikhail Zhilkin2022-06-135-2/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan WG443223). Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 128 MiB Flash: 128 MiB (Winbond W29N01HV) Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2 Wireless 5 GHz (MT7615DN): a/n/ac, 2x2 Ethernet: 3xGbE (WAN, LAN1, LAN2) USB ports: No Button: 1 (Reset/WPS) LEDs: 2 (Red, Green) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2) OEM: Arcadyan WG430223 Installation ------------ 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration -> Miscellaneous -> Access control lists & enable telnet & enable "Remote control from any IP address" 3. Connect to the router using telnet (default admin:admin) 4. Place *factory.trx on any web server (192.168.1.2 in this example) 5. Connect to the router using telnet shell (no password required) 6. Save MAC adresses to U-Boot environment: uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \ awk '{print $5}') uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \ awk '{print $5}') uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \ awk '{print $5}') uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \ awk '{print $5}') 7. Ensure that MACs were saved correctly: uboot_env --get --name eth2macaddr uboot_env --get --name eth3macaddr uboot_env --get --name ra0macaddr uboot_env --get --name rax0macaddr 8. Download and write the OpenWrt images: cd /tmp wget http://192.168.1.2/factory.trx mtd_write erase /dev/mtd4 mtd_write write factory.trx /dev/mtd4 9. Set 1st boot partition and reboot: uboot_env --set --name bootpartition --value 0 Back to Stock ------------- 1. Run in the OpenWrt shell: fw_setenv bootpartition 1 reboot 2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. MAC addresses ------------- +-----------+-------------------+----------------+ | Interface | MAC | Source | +-----------+-------------------+----------------+ | label | A4:xx:xx:51:xx:F4 | No MACs was | | LAN | A4:xx:xx:51:xx:F6 | found on Flash | | WAN | A4:xx:xx:51:xx:F4 | [1] | | WLAN_2g | A4:xx:xx:51:xx:F5 | | | WLAN_5g | A6:xx:xx:21:xx:F5 | | +-----------+-------------------+----------------+ [1]: a. Label wasb't found neither in factory nor in other places. b. MAC addresses are stored in encrypted partition "glbcfg". Encryption key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack with saving of the MACs to u-boot-env during the installation was applied. c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in "Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM firmware also uses this MAC when initialazes ethernet driver. In OpenWrt we use it only as internal GMAC (eth0), all other MACs are unique. Therefore, there is no any barriers to the operation of several MTS WG430223 devices even within the same broadcast domain. Stock firmware image format --------------------------- The same as Beeline Smartbox Flash but with another trx magic +--------------+---------------+----------------------------------------+ | Offset | | Description | +==============+===============+========================================+ | 0x0 | 31 52 48 53 | TRX magic "1RHS" | +--------------+---------------+----------------------------------------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: create new dtsi for Arcadyan routersMikhail Zhilkin2022-06-132-186/+199
| | | | | | | | | | | | | | | | | | | This commit moves common properties for the boards below to a new dtsi: Beeline Smartbox Flash (Arcadyan WG443223) MTS WG430223 (Arcadyan WG430223) The boards are almost the same. Here is the differences: +------+----------+----------+ | | WG430223 | WG443223 | +------+----------+----------+ | RAM | 128 | 256 | +------+----------+----------+ | USB | - | 1x3.0 | +------+----------+----------+ | LEDS | RG | RGB | +------+----------+----------+ Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: allow custom trx magic for ArcadyanMikhail Zhilkin2022-06-131-3/+4
| | | | | | | | | | | | This commit: 1. Renames beeline-trx recipe in mt7621.mk to arcadyan-trx. The recipe is necessary for: - MTS WG430223 (Arcadyan WG430223) - Beeline Smartbox Flash (Arcadyan WG443223) 2. Allows specify custom trx magic which is different for the routers mentined above. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ramips: decrease SPI frequency for Phicomm K2PAviana Cruz2022-06-131-2/+1
| | | | | | | | | | Some K2P comes with the worse boards with GD25Q128 (may be A2), which only works with 50MHz frequency and less. Reduce spi frequency so that these routers can boot. remove m25p,fast-read because it isn't needed for 50MHz SPI. Signed-off-by: Aviana Cruz <gwencroft@proton.me> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: move ubnt-xm to tinyNick Hainke2022-06-1111-265/+281
| | | | | | | | | | | | | ath79 has was bumped to 5.10. With this, as with every kernel change, the kernel has become larger. However, although the kernel gets bigger, there are still enough flash resources. But the RAM reaches its capacity limits. The tiny image comes with fewer kernel flags enabled and fewer daemons. Improves: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Tested-by: Robert Foss <me@robertfoss.se> Signed-off-by: Nick Hainke <vincent@systemli.org>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-16 15:21:44 +0000