aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ath79: support Ruckus ZoneFlex 7351Lech Perczak2023-03-224-0/+375
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ruckus ZoneFlex 7351 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise access point. Hardware highligts: - CPU: Atheros AR7161 SoC at 680 MHz - RAM: 64MB DDR - Flash: 16MB SPI-NOR - Wi-Fi 2.4GHz: AR9280 PCI 2x2 MIMO radio with external beamforming - Wi-Fi 5GHz: AR9280 PCI 2x2 MIMO radio with external beamforming - Ethernet: single Gigabit Ethernet port through Marvell 88E1116R gigabit PHY - Standalone 12V/1A power input - USB: optional single USB 2.0 host port on the 7351-U variant. Serial console: 115200-8-N-1 on internal H1 header. Pinout: H1 ---------- |1|x3|4|5| ---------- Pin 1 is near the "H1" marking. 1 - RX x - no pin 3 - VCC (3.3V) 4 - GND 5 - TX Installation: - Using serial console - requires some disassembly, 3.3V USB-Serial adapter, TFTP server, and removing a single T10 screw. 0. Connect serial console to H1 header. Ensure the serial converter does not back-power the board, otherwise it will fail to boot. 1. Power-on the board. Then quickly connect serial converter to PC and hit Ctrl+C in the terminal to break boot sequence. If you're lucky, you'll enter U-boot shell. Then skip to point 3. Connection parameters are 115200-8-N-1. 2. Allow the board to boot. Press the reset button, so the board reboots into U-boot again and go back to point 1. 3. Set the "bootcmd" variable to disable the dual-boot feature of the system and ensure that uImage is loaded. This is critical step, and needs to be done only on initial installation. > setenv bootcmd "bootm 0xbf040000" > saveenv 4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed: > setenv serverip 192.168.1.2 > setenv ipaddr 192.168.1.1 > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7351-initramfs-kernel.bin > bootm 0x81000000 5. Optional, but highly recommended: back up contents of "firmware" partition: $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7351_fw_backup.bin 6. Copy over sysupgrade image, and perform actual installation. OpenWrt shall boot from flash afterwards: $ ssh root@192.168.1.1 # sysupgrade -n openwrt-ath79-generic-ruckus_zf7351-squashfs-sysupgrade.bin After unit boots, it should be available at the usual 192.168.1.1/24. Return to factory firmware: 1. Copy over the backup to /tmp, for example using scp 2. Unset the "bootcmd" variable: fw_setenv bootcmd "" 3. Use sysupgrade with force to restore the backup: sysupgrade -F ruckus_zf7351_backup.bin 4. System will reboot. Quirks and known issues: - Flash layout is changed from the factory, to use both firmware image partitions for storage using mtd-concat, and uImage format is used to actually boot the system, which rules out the dual-boot capability. - Both radio has its own EEPROM on board, not connected to CPU. - The stock firmware has dual-boot capability, which is not supported in OpenWrt by choice. It is controlled by data in the top 64kB of RAM which is unmapped, to avoid the interference in the boot process and accidental switch to the inactive image, although boot script presence in form of "bootcmd" variable should prevent this entirely. - On some versions of stock firmware, it is possible to obtain root shell, however not much is available in terms of debugging facitilies. 1. Login to the rkscli 2. Execute hidden command "Ruckus" 3. Copy and paste ";/bin/sh;" including quotes. This is required only once, the payload will be stored in writable filesystem. 4. Execute hidden command "!v54!". Press Enter leaving empty reply for "What's your chow?" prompt. 5. Busybox shell shall open. Source: https://alephsecurity.com/vulns/aleph-2019014 - There is second method to achieve root shell, using command injection in the web interface: 1. Login to web administration interface 2. Go to Administration > Diagnostics 3. Enter |telnetd${IFS}-p${IFS}204${IFS}-l${IFS}/bin/sh into "ping" field 4. Press "Run test" 5. Telnet to the device IP at port 204 6. Busybox shell shall open. Source: https://github.com/chk-jxcn/ruckusremoteshell Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ramips: mt7621: enable lzma-loader for AFOUNDRY EW1200Tony Butler2023-03-221-0/+1
| | | | | | | | | Fixes boot loader LZMA decompression issues (LZMA ERROR 1) As reported in issue #12208 Reported-by: Raúl M. <raul.m@sparkedhost.com> Tested-by: Raúl M. <raul.m@sparkedhost.com> Signed-off-by: Tony Butler <spudz76@gmail.com>
* bmips: add support for Sercomm H-500sÁlvaro Fernández Rojas2023-03-228-1/+502
| | | | | | | | | | | | | Sercomm H-500s is a BCM63268 with 128M, internal and external (Quantenna) wifi and external BCM53134S switch. This device is already supported in bcm63xx target, so more information can be found in https://openwrt.org/toh/sercomm/h500-s. It's a perfect example of a device with internal and external switch coexistance since most devices only have ports on one of the switches but not both of them. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: drop unneded cpu labels from external switchesÁlvaro Fernández Rojas2023-03-222-2/+0
| | | | | | | | | These labels aren't needed and were accidentally added when adding external switches support for bmips. Fixes: 80a3ecc89489 ("bmips: add Huawei HG253s v2 support") Fixes: 61f3c3b1eebd ("bmips: dgnd3700v2: enable external BCM53125 switch") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: add pending patches for bcm63268-timer-clocksÁlvaro Fernández Rojas2023-03-227-165/+435
| | | | | | | | | bcm63268-timer-clocks have been sent upstream with a positive review, so let's add them to pending v5.15. Also add devm_clk_hw_register_gate() patch from v5.17 to backports since it's needed for upstream bcm63268-timer-clocks patches. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dts: nand: add missing address/size cellsÁlvaro Fernández Rojas2023-03-212-0/+6
| | | | | | | | | | | Fixes the following warnings for Netgear DGND3700v2 and Comtrend VR-3032u: [ 1.059540] 7 fixed-partitions partitions found on MTD device brcmnand.0 [ 1.066570] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions [ 1.073766] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions [ 1.081927] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions [ 1.089128] OF: Bad cell count for /ubus/nand@10000200/nandcs@0/partitions Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: add Huawei HG253s v2 supportÁlvaro Fernández Rojas2023-03-214-0/+264
| | | | | | | | | | | | | Huawei HG253s v2 is a BCM6362 with 128M RAM, internal wifi and external BCM53124S switch. This device is already supported in bcm63xx target, so more information can be found in https://openwrt.org/toh/huawei/hg253s_v2. It's a perfect example of a device with internal and external switch coexistance since most devices only have ports on one of the switches but not both of them. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dgnd3700v2: enable external BCM53125 switchÁlvaro Fernández Rojas2023-03-212-2/+56
| | | | | | | The Netgear DGND3700v2 has an external BCM53125 switch which can now be enabled as a DSA disjoint switch tree setup. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: disable B53 MMAP phy read/write opsÁlvaro Fernández Rojas2023-03-212-1/+47
| | | | | | | | | | Without this change, internal and external B53 switches couldn't coexist as reported in https://github.com/openwrt/openwrt/issues/10313. In order to fix this we need to force the B53 MMAP DSA switch driver to use bcm6368-mdio-mux for accessing the PHY registers instead of its own phy_read() and phy_write() functions. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: update pending b53 mmap patchesÁlvaro Fernández Rojas2023-03-214-206/+244
| | | | | | | | Update B53 MMAP pending patches to the latest version sent upstream. Fixes regression in bmips BCM63268 switches. Fixes: fff07085fb5a ("kernel: add pending bmips patches") Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ipq40xx: add support for Wallystech DR40x9Robert Marko2023-03-215-1/+441
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Wallys DR40x9 series boards. They come in IPQ4019 and IPQ4029 versions. IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures. Specifications are: * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz * RAM: 512 MB * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND * USB 3.0 TypeA port for users * MiniPCI-E with PCI-E 2.0 link * MiniPCI-E for LTE modems with only USB2.0 link * 2 SIM card slots that are selected via GPIO11 * MicroSD card slot * Ethernet: 2x GBe with 24~48V passive POE * SFP port (Does not work, I2C and GPIO's not connected on hardware) * DC Jack * UART header * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac * 4x MMCX connectors for WLAN * Reset button * 8x LED-s Installation instructions: Connect to UART, pins are like this: -> 3.3V | TX | RX | GND Settings are 115200 8n1 Boot initramfs from TFTP: tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb bootm Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name> The board file binary was provided from Wallystech on March 14th 2023 including full permission to use and distribute. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* kernel: add missing symbols in 5.15Koen Vandeputte2023-03-211-0/+6
| | | | | | Found these while playing around with video support Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* kernel: backport eth_addr_add()Rafał Miłecki2023-03-214-4/+86
| | | | | | It's required by upcoming NVMEM layout drivers. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: fix Archer AX23 WiFi MAC address conflictDavid Bauer2023-03-211-4/+1
| | | | | | | | | | The original claim about conflicting MAC addresses is wrong. mac80211 does increment the first octet and sets the LA bit. This means our "workaround" actually leads to the issue while incrementing the last octet is safe. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: cudy wr1300v2 reduce SPI freq to 40000000Óscar García Amor2023-03-201-2/+1
| | | | | | | | | Cases have been reported in which certain devices do not boot correctly or have errors. After various tests by users who have such errors it has been concluded that the SPI frequency should be reduced to 40Mhz, at this speed it appears that all devices work correctly. Signed-off-by: Óscar García Amor <ogarcia@connectical.com>
* kernel: bump 5.10 to 5.10.175John Audia2023-03-2036-210/+134
| | | | | | | | | | | | | | Manually rebased: backport-5.10/611-v5.12-net-ethernet-mediatek-support-setting-MTU.patch Removed upstreamed: bcm47xx/patches-5.10/170-bgmac-fix-initial-chip-reset-to-support-BCM5358.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.175&id=cbf11ff3708ff163387da924f80a47ce7c721e9b Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.173John Audia2023-03-2035-88/+79
| | | | | | | | | Manually rebased: ramips/patches-5.10/810-uvc-add-iPassion-iP2970-support.patch All other patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: tcindex classifier has been retiredJohn Audia2023-03-201-1/+0
| | | | | | https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/net/sched?h=v5.10.173&id=18c3fa7a7fdbb4d21dafc8a7710ae2c1680930f6 Signed-off-by: John Audia <therealgraysky@proton.me>
* x86: fix deprecated CONFIG_MICROCODE_OLD_INTERACEJohn Audia2023-03-201-1/+1
| | | | | | | | | | | We use late loading[1] so need to set this option despite upstream adding a kernel taint when this option is set. See discussion in PR#12149 for more details. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/x86/Kconfig?id=v5.10.173&id2=v5.10.172 1. https://github.com/openwrt/openwrt/blob/master/target/linux/x86/base-files/lib/preinit/02_load_x86_ucode Signed-off-by: John Audia <therealgraysky@proton.me>
* mpc85xx: poll PHY statusDavid Bauer2023-03-202-4/+4
| | | | | | | | | | Disable interrupts for the eth-PHYs, as the interrupts are either not firing or lost within the stack. Switch to polling the PHY status in the meantime until a proper fix is implemented. Ref: https://github.com/openwrt/openwrt/issues/12192 Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: use bootwrapper for ws-ap3825iDavid Bauer2023-03-204-2/+81
| | | | | | | | | | | | | | | The boot-procedure for the Extreme WS-AP3825I is vfragile to put it mildly. It does not relocate the FDT properly. It currently exercises every step manually as well as coming with a pre-padded dtb. Use the PowerPC bootwrapper code for legacy platforms with a pre-filles DTS instead. We still need to ship a fit image to not break the fdt resize / relocate instructions on existing boards. This does not require adapting the U-Boot bootcommand. Ref: https://github.com/openwrt/openwrt/issues/12223 Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: filogic: move ilm, dlm and cpu_boot in dedicated nodesLorenzo Bianconi2023-03-207-0/+522
| | | | | | | | This fixes issues with legacy boot loaders that don't process reserved memory regions outside of system RAM Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: move mediatek flow offload refcount fix and fix a logic errorFelix Fietkau2023-03-201-4/+13
| | | | | | | Move it to pending, since it wasn't actually accepted upstream yet. Fixes potential issues when doing offload between multiple MACs. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* bmips: dts: fix switch compatible stringsÁlvaro Fernández Rojas2023-03-204-4/+4
| | | | | | Use the proper string for each SoC. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: add pending bmips patchesÁlvaro Fernández Rojas2023-03-2015-246/+1109
| | | | | | Add patches sent upstream for bmips and b53 and remove downstream ones. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ipq807x: add support for Netgear WAX218Alexandru Gagniuc2023-03-206-1/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall or ceiling mountable. It can be powered via PoE, or a 12 V adapter. The board has footprints for 2.54mm UART headers. They're difficult to solder because the GND is connected to a large copper plane. Only try soldering if you are very skilled. Otherwise, use pogo pins. Specifications: --------------- * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 366 MB of RAM available to OS, not sure of total amount * Storage: Macronix MX30UF2G18AC 256MB NAND * Ethernet: * 2.5G RJ45 port (QCA8081) with PoE input * WLAN: * 2.4GHz/5GHz with 8 antennas * LEDs: * Power (Amber) * LAN (Blue) * 2G WLAN (Blue) * 5G WLAN (Blue) * Buttons: * 1x Factory reset * Power: 12V DC Jack * UART: Two 4-pin unpopulated headers near the LEDs * "J2 UART" is the CPU UART, 3.3 V level Installation: ============= Web UI method ------------- Flashing OpenWRT using the vendor's Web UI is problematic on this device. The u-boot mechanism for communicating the active rootfs is antiquated and unreliable. Instead of setting the kernel commandline, it relies on patching the DTS partitions of the nand node. The way partitions are patched is incompatible with newer kernels. Newer kernels use the SMEM partition table, which puts "rootfs" on mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One reliable way to boot from mtd14 and avoid boot loops is to use an initramfs image. 1. In the factory web UI, navigate to System Manager -> Firmware. 2. In the "Local Firmware Upgrade" section, click Browse 3. Navigate and select the 'web-ui-factory.fit' image 4. Click "Upload" 5. On the following page, click on "Proceed" The flash proceeds at this point and the system will reboot automatically to OpenWRT. 6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline SSH method ---------- Enable SSH using the CLI or Web UI. The root account is locked out to ssh, and the admin account defaults to Netgear's CLI application. So we need to get creative: First, make sure the device boots from the second firmware partition: ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 1 Then reboot the device, and run the update: scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \ -o hostkeyalgorithms=ssh-rsa \ netgear_wax218-squashfs-nand-factory.ubi \ admin@<ipaddr>:/tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 0 Now reboot the device, and it should boot into a ready-to-use OpenWRT. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Francisco G Luna <frangonlun@gmail.com>
* mpc85xx: fix incorrect kernel targetDavid Bauer2023-03-201-1/+1
| | | | | | | | | | | | | | | The wrapper-image for the WL-WDR4900 was used as a build-target for the kernel. This workd fine as long as only a single wrapper is used with the OpenWrt build-system. If additional wrappers are used, the build becomes racy in the wrapper-stage. The wrapper images actually do not represent a target. They are built based on the kernel configuration. Only copy the resulting images to avoid race-conditions as explained. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: remove Watchguard T10 MAC overrideDavid Bauer2023-03-201-5/+0
| | | | | | | | As the mac-address readout never worked, the mac-address fillout by the bootloader is sufficient. Remove the readout for the Watchguard T10 then. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: fix missing system importDavid Bauer2023-03-201-0/+1
| | | | | | | The mac-address accessor functions were not included in the sourced script. Fix this by importing the correct script path. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: Add CONFIG_KERNEL_HARDLOCKUP_DETECTORHauke Mehrtens2023-03-191-0/+1
| | | | | | | Make it possible to change the kernel configuration option CONFIG_HARDLOCKUP_DETECTOR from OpenWrt. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* kernel: Deactivate options shown with CONFIG_KERNEL_KCOV=yHauke Mehrtens2023-03-191-0/+1
| | | | | | | This sets the CONFIG_KCOV_IRQ_AREA_SIZE kernel configuration option to its default value. This is shown when I set CONFIG_KERNEL_KCOV=y in the OpenWrt configuration on x86/64. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* kernel: Deactivate options shown with CONFIG_KERNEL_KASAN=yHauke Mehrtens2023-03-191-0/+2
| | | | | | | | | This deactivates some kernel configuration options I see when CONFIG_KERNEL_KASAN=y is set in the OpenWrt configuration on x86/64. Set CONFIG_STACK_HASH_ORDER to its default value. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* kernel: Set some options to default shown with CONFIG_KERNEL_UBSAN=yHauke Mehrtens2023-03-191-0/+5
| | | | | | | | This sets some kernel configuration options to their default values. I saw these as warnings when I set CONFIG_KERNEL_UBSAN=y is set in the OpenWrt configuration on x86/64. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* kernel: Deactivate options shown with CONFIG_KERNEL_DYNAMIC_FTRACE=yHauke Mehrtens2023-03-191-0/+1
| | | | | | | This deactivates some kernel configuration options I see when CONFIG_KERNEL_DYNAMIC_FTRACE=y is set in the OpenWrt configuration on x86/64. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* kernel: Deactivate options shown with CONFIG_KERNEL_HIST_TRIGGERS=yHauke Mehrtens2023-03-191-0/+2
| | | | | | | This deactivates some kernel configuration options I see when CONFIG_KERNEL_HIST_TRIGGERS=y is set in the OpenWrt configuration on x86/64. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* kernel: Deactivate options shown with CONFIG_KERNEL_DEBUG_VIRTUAL=yHauke Mehrtens2023-03-191-0/+1
| | | | | | | This deactivates some kernel configuration options I see when CONFIG_KERNEL_DEBUG_VIRTUAL=y is set in the OpenWrt configuration on x86/64. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* kernel: Deactivate options shown with CONFIG_KERNEL_DEBUG_VM=yHauke Mehrtens2023-03-191-0/+3
| | | | | | | This deactivates some kernel configuratoion options I see when CONFIG_KERNEL_DEBUG_VM=y is set in the OpenWrt configuration on x86/64. Signed-off-by: Hauke Mehrtens <hmehrtens@maxlinear.com>
* ipq806x: add support for Nokia Airscale AC400iKristjan Krušič2023-03-196-0/+350
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Qualcomm IPQ8065 RAM: 512 MB DDR3 Flash: 256 MB NAND (Macronix MX30UF2G18AC) (split into 2x128MB) 4 MB SPI-NOR (Macronix MX25U3235F) WLAN: Qualcomm Atheros QCA9984 - 2.4Ghz Qualcomm Atheros QCA9984 - 5Ghz ETH: eth0 - POE (100Mbps in U-Boot, 1000Mbps in OpenWrt) eth1 - (1000Mbps in both) Auto-negotiation broken on both. USB: USB 2.0 LED: 5G, 2.4G, ETH1, ETH2, CTRL, PWR (All support green and red) BTN: Reset Other: SD card slot (non-functional) Serial: 115200bps, near the Ethernet transformers, labeled 9X. Connections from the arrow to the 9X text: [NC] - [TXD] - [GND] - [RXD] - [NC] Installation ------------ 0. Connect to the device Plug your computer into LAN2 (1000Mbps connection required). If you use the LAN1/POE port, set your computer to force a 100Mbps link. Connect to the device via TTL (Serial) 115200n8. Locate the header (or solder pads) labeled 9X, near the Ethernet jacks/transformers. There should be an arrow on the other side of the header marking. The connections should go like this: (from the arrow to the 9X text): NC - TXD - GND - RXD - NC 1. Prepare for installation While the AP is powering up, interrupt the startup process. MAKE SURE TO CHECK YOUR CURRENT PARTITION! If you see: "Current Partition is : partB" or "Need to switch partition from partA to partB", you have to force the device into partA mode, before continuing. This can be done by changing the PKRstCnt to 5 and resetting the device. setenv PKRstCnt 5 saveenv reset After you interrupt the startup process again, you should see: Need to switch partition from partB to partA You can now continue to the next step. If you see: "Current Partition is : partA", you can continue to the next step. 2. Prevent partition switching. To prevent the device from switching partitions, we are going to modify the startup command. set bootcmd "setenv PKRstCnt 0; saveenv; bootipq" setenv 3. First boot Now, we have to boot the OpenWrt intifs. The easiest way to do this is by using Tiny PXE. You can also use the normal U-Boot tftp method. Run "bootp" this will get an IP from the DHCP server and possibly the firmware image. If it doesn't download the firmware image, run "tftpboot". Now run "bootm" to run the image. You might see: "ERROR: new format image overwritten - must RESET the board to recover" this means that the image you are trying to load is too big. Use a smaller image for the initial boot. 4. Install OpenWrt from initfs Once you are booted into OpenWrt, transfer the OpenWrt upgrade image and use sysupgrade to install OpenWrt to the device. Signed-off-by: Kristjan Krušič <kristjan.krusic@krusic22.com>
* lantiq: xway: add phy reset pin to AVM Fritz!Box 7320Aleksander Jan Bajkowski2023-03-191-0/+17
| | | | | | | | | | This commit adds the PHY reset gpio for the LAN1 port to the dts. According to the GPL sources, gpios 34 and 36 are used on the AVM FritzBox 7320 and 7330. The second port is unsupported. The gpio assignment has been verified on the FritzBox 7330. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* ipq40xx: mf18a: rename wifi0 calibration variant to ZTE-MF18AChristian Marangi2023-03-181-1/+1
| | | | | | | Rename wifi0 calibration variant to ZTE-MF18A to allign to BDF changes for ZTE MF18A. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: rutx10: Add missing variant to ath10k wifiChristian Marangi2023-03-181-0/+10
| | | | | | | Add missing variant to ath10k wifi to allign to BDF changes for Teltonika RUTX10. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: mf18a: Add missing variant to PCI ath10k cardChristian Marangi2023-03-181-0/+1
| | | | | | | Add missing variant to PCI ath10k card to allign to BDF changes for ZTE MF18A. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* kernel: bump 5.15 to 5.15.100John Audia2023-03-18148-964/+391
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Manually rebased: bcm27xx/patches-5.15/950-0421-Support-RPi-DPI-interface-in-mode6-for-18-bit-color.patch bcm27xx/patches-5.15/950-0706-media-i2c-imx219-Scale-the-pixel-clock-rate-for-the-.patch ramips/patches-5.15/810-uvc-add-iPassion-iP2970-support.patch Removed upstreamed: bcm27xx/patches-5.15/950-0707-drm-vc4-For-DPI-MEDIA_BUS_FMT_RGB565_1X16-is-mode-1-.patch[1] bcm27xx/patches-5.15/950-0596-drm-vc4-dpi-Add-option-for-inverting-pixel-clock-and.patch[2] ipq807x/0006-v5.16-arm64-dts-qcom-Fix-IPQ8074-PCIe-PHY-nodes.patch [3] ipq807x/0034-v6.1-arm64-dts-qcom-ipq8074-fix-PCIe-PHY-serdes-size.patch [4] ipq807x/0103-arm64-dts-qcom-ipq8074-fix-Gen2-PCIe-QMP-PHY.patch [5] ipq807x/0104-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-QMP-PHY.patch [6] ipq807x/0105-arm64-dts-qcom-ipq8074-correct-Gen2-PCIe-ranges.patch [7] ipq807x/0108-arm64-dts-qcom-ipq8074-fix-Gen3-PCIe-node.patch [8] ipq807x/0109-arm64-dts-qcom-ipq8074-correct-PCIe-QMP-PHY-output-c.patch [9] ipq807x/0132-arm64-dts-qcom-ipq8074-correct-USB3-QMP-PHY-s-clock-.patch [10] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.99&id=d2991e6b30020e286f2dd9d3b4f43548c547caa6 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/gpu/drm/vc4/vc4_dpi.c?h=v5.15.100&id=8e04aaffb6de5f1ae61de7b671c1531172ccf429 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=a55a645aa303a3f7ec37db69822d5420657626da 4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=d9df682bcea57fa25f37bbf17eae56fa05662635 5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=7e6eeb5fb3aa9e5feffdb6e137dcc06f5f6410e1 6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=e88204931d9a60634cd50bbc679f045439c4b91d 7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=1563af0f28afd3b6d64ac79a2aecced3969c90bf 8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=feb8c71f015d416f1afe90e1f62cf51e47376c67 9. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=69c7a270357a7d50ffd3471b14c60250041200e3 10. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/arch/arm64/boot/dts/qcom/ipq8074.dtsi?h=v5.15.99&id=dd3d021ae5471d98adf81f1e897431c8657d0a18 Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3 Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me> Tested-by: Robert Marko <robimarko@gmail.com> #ipq807x/Dynalink WRX36 Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, ath79/tl-wdr3600, ipq806x/g10, ipq806x/nbg6817
* kernel: tcindex classifier has been retiredJohn Audia2023-03-181-1/+0
| | | | | | https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/net/sched?h=v5.15.100&id=7c183dc0af472dec33d2c0786a5e356baa8cad19 Signed-off-by: John Audia <therealgraysky@proton.me>
* x86: set deprecated CONFIG_MICROCODE_OLD_INTERACEJohn Audia2023-03-181-1/+1
| | | | | | | | | | | We use late loading[1] so need to set this option despite upstream adding a kernel taint when this option is set. See discussion in PR#12149 for more details. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/diff/arch/x86/Kconfig?id=v5.15.100&id2=v5.15.98 1. https://github.com/openwrt/openwrt/blob/master/target/linux/x86/base-files/lib/preinit/02_load_x86_ucode Signed-off-by: John Audia <therealgraysky@proton.me>
* uencrypt: add support for mbedtlsEneas U de Queiroz2023-03-172-3/+3
| | | | | | | | | | | | | | This commit includes some additional changes: - better handling of iv and keys in openssl/wolfssl variants - fix compiler warnings and whitespace - build all 3 variants as separate packages - adjust the new package name in targets' DEVICE_PACKAGES - remove PKG_FLAGS:=nonshared [Beeline SmartBox Flash - OK] Tested-by: Mikhail Zhilkin <csharper2005@gmail.com> [after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size] Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* kernel: update v6.3 of patchesRafał Miłecki2023-03-1712-108/+164
| | | | | | | 1. Use final (accepted) patches 2. Add two more required for v6.4 nvmem stuff Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq40xx: update Crisis Innovation Lab MeshPoint.One BDFMantas Pucka2023-03-171-1/+1
| | | | | | | | | | Make sure it uses updated Jalapeno BDF inherited from Device/8dev_jalapeno-common Fixes: 146eb4925c7f ("ipq40xx: add support for Crisis Innovation Lab MeshPoint.One") Signed-off-by: Mantas Pucka <mantas@8devices.com> [ fix Fixes tag to correct format and fix commit title ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: set specific BDF file for 8devices Habanero/JalapenoMantas Pucka2023-03-171-0/+2
| | | | | | | | | Set specific BDF file for 8devices Habanero/Jalapeno in ipq40xx generic.mk Signed-off-by: Mantas Pucka <mantas@8devices.com> [ split ipq40xx changes in separate commit ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* layerscape: switch to Kernel 5.15 by defaultPaul Spooren2023-03-171-2/+3
| | | | | | | Getting ready for the next release. Tested-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Paul Spooren <mail@aparcar.org>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-15 17:12:05 +0000