aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* kernel: update FIT partition parser to new property nameDaniel Golle2022-04-201-1/+1
| | | | | | | | The commit "uboot-mediatek: replace patch with accepted commit" changed the name of the boot configuration property from 'bootconf' to 'u-boot,bootconf'. Reflect this change in the FIT partition parser. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: x86: remove an upstreamed patchRui Salvaterra2022-04-202-100/+0
| | | | | | | | | 012-pcengines-apu2-detect-apuv4-board.patch is upstream since Linux 5.5 [1]. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.5&id=3d00da1de3ea36ba44f4a7ba76c8c8b16f98204b Acked-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: add missing config symbolsFelix Fietkau2022-04-202-0/+4
| | | | | | | | MPLS feature symbols are normally only set when kmod-mpls is enabled, but the CONFIG_MPLS symbol they depend on could also have been selected by openvswitch instead Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: mt7622: remove '0x' prefix from pstore address in dtsDaniel Golle2022-04-192-2/+2
| | | | | | | | | | | | | | Adresses of device tree nodes are typically noted without the '0x' prefix. While having the '0x' prefix doesn't hurt when using Linux, more recent versions of U-Boot will add a duplicate ramoops node as a simple string compare is used to check if the node is already present. Remove the '0x' prefix to avoid the kernel warning resulting from U-Boot adding a dupplicate pstore/ramoops node. See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: remove crypto-hw-mtk packageEneas U de Queiroz2022-04-191-23/+0
| | | | | | | The MediaTek's Crypto Engine module is only available for mt7623, in which case it is built into the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* ath79: add support for MikroTik RouterBOARD wAP-2nD (wAP)David Musil2022-04-185-1/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik RouterBOARD wAP-2nd (sold as wAP) is a small 2.4 GHz 802.11b/g/n PoE-capable AP. Specifications: - SoC: Qualcomm Atheros QCA9533 - Flash: 16 MB (SPI) - RAM: 64 MB - Ethernet: 1x 10/100 Mbps (PoE in) - WiFi: AR9531 2T2R 2.4 GHz (SoC) - 3x green LEDs (1x lan, 1x wlan, 1x user) See https://mikrotik.com/product/RBwAP2nD for more info. Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Note: following 781d4bfb397cdd12ee0151eb66c577f470e3377d The network setup avoids using the integrated switch and connects the single Ethernet port directly. This way, link speed (10/100 Mbps) is properly reported by eth0. Signed-off-by: David Musil <0x444d@protonmail.com>
* ramips: add support for OrayBox X3ARay Wang2022-04-175-0/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621. Specification: * SoC: MT7621 * RAM: DDR3 128 MiB * Flash: 16 MiB NOR (XM25Q128) * Wi-Fi: (single chip hosting both 2.4G and 5G) * 2.4GHz: MT7615 * 5GHz: MT7615 * Ethernet: 3x 1000Mbps * Switch: MT7530 * LED: * Ethernet LEDs: On the back of the router, hardware-controlled. * Status LEDs: One "pixel-like" RGB LED in the front of the router, which is actually made up of 3 individual LEDs (with dedicated GPIO pins) with the color of Red, Green, and Blue. The OEM firmware only lights up one color at a time to indicate status, but that's very boring, and the colors actually look great when combined, so I've improvised a little and made them indicate netdev activities. My test results: GPIO 13/14/15 000 white (actually more like bright green or cyan because the brightness of the green LED is higher than red and blue) 001 bright purple 010 bright green 011 red 100 bright cyan 101 blue 110 green 111 off Flash Layout: 0x0000000-0x0030000 : "u-boot" 0x0030000-0x0040000 : "u-boot-env" 0x0040000-0x0050000 : "factory" 0x0050000-0x0f50000 : "firmware" /*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/ 0x0fe0000-0x0ff0000 : "bdinfo" 0x0ff0000-0x1000000 : "reserve" MAC address: MAC Source Description Fix A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A Stock dmesg: https://pastebin.com/2t2jwLdf Stock Dumps: https://pastebin.com/LDLxSWX3 Installation via SSH (does not void your warranty): 1. -----UNLOCK SSH----- 1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in your browser. Password is 'admin'. 1.2 Click the "备份且导出" (backup and export) button, and download the config file. 1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'. 1.4 Edit the file './system'. Change the '0' into '1' under "config sys 'ssh'". 1.5 Save the file. 1.6 Upload the file by clicking the "导入且恢复" (import and recover) button. The router will automatically reboot. 2. -----FLASH THE OPENWRT FIRMWARE----- 2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/' folder to your router. It should be root@10.168.1.1 and the password is 'admin'. 2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'. 2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to backup the stock firmware. Since the OEM does not provide firmware download on their website, this is the only way to get it. 2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock firmware from '/tmp/' to your local drive. Then you'd better use a hex reading tool to have a rough look at it to make sure nothing is corrupt. Or u can just back up again and cross check the MD5. 2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash the firmware. 2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and reboot the router. Revert to stock firmware: 1. load stock firmware using mtd (make sure u have a backup). Signed-off-by: Ray Wang <raywang777@foxmail.com>
* realtek: add ZyXEL GS1900-24HP v1 supportMartin Kennedy2022-04-163-0/+135
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24HP v1 is a 24 port PoE switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24HP v1 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: * 1 PWR LED (green, not configurable) * 1 SYS LED (green, configurable) * 24 ethernet port link/activity LEDs (green, SoC controlled) * 24 ethernet port PoE status LEDs * 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: * 1 "RESET" button on front panel (soft reset) * 1 button ('SW1') behind right hex grate (hardwired power-off) * PoE: * Management MCU: ST Micro ST32F100 Microcontroller * 6 BCM59111 PSE chips * 170W power budget * Power: 120-240V AC C13 * UART: Internal populated 10-pin header ('J5') providing RS232; connected to SoC UART through a TI or SIPEX 3232C for voltage level shifting. * 'J5' RS232 Pinout (dot as pin 1): 2) SoC RXD 3) GND 10) SoC TXD Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on * Since the GS1900-24HP v1 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only be installed in the first partition anyway (hardcoded in the DTS). To ensure we are set to boot from the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24hp-v1-squashfs-sysupgrade.bin Signed-off-by: Martin Kennedy <hurricos@gmail.com> [Add info on PoE hardware to commit message] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ipq806x: RT4230W: utilize nvmem-cells for ath10k caldataChukun Pan2022-04-162-17/+66
| | | | | | | | | | | Converts extraction entries from 11-ath10k-caldata into nvmem-cells in the individual board's device-tree file. Same as commit 2047058 ("ipq806x: utilize nvmem-cells for pre-calibration data") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: Askey RT4230W REV6: enable onboard spi flashChukun Pan2022-04-161-0/+29
| | | | | | | | | | | There is a mr25h256 spi flash on this machine. From the mtd backup of the stock firmware, this spi flash is empty. [ 3.652745] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 3.653925] spi-nor spi0.0: mr25h256 (32 Kbytes) Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ath79: add support for Sophos AP100/AP55 familyAndrew Powers-Holmes2022-04-168-0/+281
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sophos AP100, AP100C, AP55, and AP55C are dual-band 802.11ac access points based on the Qualcomm QCA9558 SoC. They share PCB designs with several devices that already have partial or full support, most notably the Devolo DVL1750i/e. The AP100 and AP100C are hardware-identical to the AP55 and AP55C, however the 55 models' ART does not contain calibration data for their third chain despite it being present on the PCB. Specifications common to all models: - Qualcomm QCA9558 SoC @ 720 MHz (MIPS 74Kc Big-endian processor) - 128 MB RAM - 16 MB SPI flash - 1x 10/100/1000 Mbps Ethernet port, 802.3af PoE-in - Green and Red status LEDs sharing a single external light-pipe - Reset button on PCB[1] - Piezo beeper on PCB[2] - Serial UART header on PCB - Alternate power supply via 5.5x2.1mm DC jack @ 12 VDC Unique to AP100 and AP100C: - 3T3R 2.4GHz 802.11b/g/n via SoC WMAC - 3T3R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express) AP55 and AP55C: - 2T2R 2.4GHz 802.11b/g/n via SoC WMAC - 2T2R 5.8GHz 802.11a/n/ac via QCA9880 (PCI Express) AP100 and AP55: - External RJ45 serial console port[3] - USB 2.0 Type A port, power controlled via GPIO 11 Flashing instructions: This firmware can be flashed either via a compatible Sophos SG or XG firewall appliance, which does not require disassembling the device, or via the U-Boot console available on the internal UART header. To flash via XG appliance: - Register on Sophos' website for a no-cost Home Use XG firewall license - Download and install the XG software on a compatible PC or virtual machine, complete initial appliance setup, and enable SSH console access - Connect the target AP device to the XG appliance's LAN interface - Approve the AP from the XG Web UI and wait until it shows as Active (this can take 3-5 minutes) - Connect to the XG appliance over SSH and access the Advanced Console (Menu option 5, then menu option 3) - Run `sudo awetool` and select the menu option to connect to an AP via SSH. When prompted to enable SSH on the target AP, select Yes. - Wait 2-3 minutes, then select the AP from the awetool menu again. This will connect you to a root shell on the target AP. - Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc - Run `mtd -r write /tmp/openwrt.bin astaro_image` - When complete, the access point will reboot to OpenWRT. To flash via U-Boot serial console: - Configure a TFTP server on your PC, and set IP address 192.168.99.8 with netmask 255.255.255.0 - Copy the firmware .bin to the TFTP server and rename to 'uImage_AP100C' - Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4] - Connect the AP ethernet to your PC's ethernet port - Connect a terminal to the UART at 115200 8/N/1 as usual - Power on the AP and press a key to cancel autoboot when prompted - Run the following commands at the U-Boot console: - `tftpboot` - `cp.b $fileaddr 0x9f070000 $filesize` - `boot` - The access point will boot to OpenWRT. MAC addresses as verified by OEM firmware: use address source LAN label config 0x201a (label) 2g label + 1 art 0x1002 (also found at config 0x2004) 5g label + 9 art 0x5006 Increments confirmed across three AP55C, two AP55, and one AP100C. These changes have been tested to function on both current master and 21.02.0 without any obvious issues. [1] Button is present but does not alter state of any GPIO on SoC [2] Buzzer and driver circuitry is present on PCB but is not connected to any GPIO. Shorting an unpopulated resistor next to the driver circuitry should connect the buzzer to GPIO 4, but this is unconfirmed. [3] This external RJ45 serial port is disabled in the OEM firmware, but works in OpenWRT without additional configuration, at least on my three test units. [4] On AP100/AP55 models the UART header is accessible after removing the device's top cover. On AP100C/AP55C models, the PCB must be removed for access; three screws secure it to the case. Pin 1 is marked on the silkscreen. Pins from 1-4 are 3.3V, GND, TX, RX Signed-off-by: Andrew Powers-Holmes <andrew@omnom.net>
* ath79: add support for MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac)Ryan Mounce2022-04-166-0/+254
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD 962UiGS-5HacT2HnT (hAP ac) Specifications: - SoC: QCA9558 - RAM: 128 MB - Flash: 16 MB SPI - 2.4GHz WLAN: 3x3:3 802.11n on SoC - 5GHz WLAN: 3x3:3 802.11ac on QCA9880 connected via PCIe - Switch: 5x 1000/100/10 on QCA8337 connected via RGMII - SFP cage: connected via SGMII (tested with genuine & generic GLC-T) - USB: 1x type A, GPIO power switch - PoE: Passive input on Ether1, GPIO switched passthrough to Ether5 - Reset button - "SFP" LED connected to SoC - Ethernet LEDs connected to QCA8337 switch - Green WLAN LED connected to QCA9880 Not working: - Red WLAN LED Installation: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* ramips: mt7621: make u_env partition r/w for Linksys EA7xxx devicesRussell Morris2022-04-161-1/+0
| | | | | | | | Make u_env partition read/write - currently cannot write to it, which blocks fw_setenv. This in turn breaks features like Advanced Reboot, which rely on setting the environment variable boot_part (1 or 2). Signed-off-by: Russell Morris <rmorris@rkmorris.us>
* ramips: add support for ASUS RT-AC1200-V2Tamas Balogh2022-04-165-131/+188
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specifications: SoC: MT7628DAN MIPS_24KEc@580MHz 2.4G-n 2x2 WiFi: MT7613BEN 5G-ac 160MHz 2x2 Switch: 4x100M built-in SoC Flash: 16MB W25Q128JVSQ SPI-NOR DRAM: 64MB built-in SoC MAC addresses as verified by OEM firmware: use address source Lan/Wan/2G *:60 factory 0x4 (label) 5G *:64 factory 0x8000 Serial console: 57600,8n1 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot TFTP Recovery method: set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing after flashing OpenWrt, there will be first no 5GHz Wifi available probably, wait until blinking finishes and do a reboot Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* kernel: bump 5.15 to 5.15.34Rui Salvaterra2022-04-1614-88/+16
| | | | | | | | | Deleted (upstreamed): generic/pending-5.15/850-0003-PCI-aardvark-Fix-support-for-MSI-interrupts.patch [1] [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.34&id=60eabd66d17fa2cbc31f670b2f201f0bc54090a2 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.111John Audia2022-04-1623-177/+40
| | | | | | | | | | | | | | Removed upstreamed: pending-5.10/850-0003-PCI-aardvark-Fix-support-for-MSI-interrupts.patch apm821xx/patches-5.10/150-ata-sata_dwc_460ex-Fix-crash-due-to-OOB-write.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* ramips: add support for BOLT! ArionAbdul Aziz Amar2022-04-163-0/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is from now-defunct BOLT! ISP in Indonesia. The original firmware is based on mediatek SDK running linux 2.6 or 3.x in later revision. Specifications: - SoC: MediaTek MT7621 - Flash: 32 MiB NOR SPI - RAM: 128 MiB DDR3 - Ethernet: 2x 10/100/1000 Mbps (switched, LAN + WAN) - WIFI0: MT7603E 2.4GHz 802.11b/g/n - WIFI1: MT7612E 5GHz 802.11ac - Antennas: 2x internal, non-detachable - LEDs: Programmable LEDs: 5 blue LEDs (wlan, tel, sig1-3) and 2 red LEDs (wlan and sig1) Non-programmable "Power" LED - Buttons: Reset and WPS Instalation: Install from TFTP Set your PC IP to 10.10.10.3 and gateway to 10.10.10.123 Press "1" when turning on the router, and type the initramfs file name You also need to solder pin header or cable to J4 or neighboring test points (T19-T21) Pinouts from top to bottom: GND, TX, RX, VCC (3.3v) Baudrate: 57600n8 There's also an additional gigabit transformer and RTL8211FD managed by the LTE module on the backside of the PCB. Signed-off-by: Abdul Aziz Amar <abdulaziz.amar@gmail.com>
* ramips: add support for Wavlink WL-WN531A3Davide Fioravanti2022-04-163-1/+162
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Wavlink WL-WN531A3 is an AC1200 router with 5 fast ethernet ports and one USB 2.0 port. It's also known as Wavlink QUANTUM D4. Hardware -------- SoC: Mediatek MT7628AN RAM: 64MB FLASH: 8MB NOR (GigaDevice GD25Q64CSIG3) ETH: - 5x 10/100 Mbps Ethernet (4x LAN + 1x WAN) WIFI: - 2.4GHz: 1x (integrated in SOC) (2x2:2) - 5GHz: 1x MT7612E (2x2:2) - 4 external antennas BTN: - 1x Reset button - 1x WPS button - 1x Turbo button - 1x Touchlink button - 1x ON/OFF switch LEDS: - 1x Red led (system status) - 1x Blue led (system status) - 7x Blue leds (wifi led + 5 ethernet ports + power) USB: - 1x USB 2.0 port UART: - 57600-8-N-1 J1 O VCC +3,3V (near lan ports) o RX o TX o GND Everything works correctly. Currently there is no firmware update available. Because of this, in order to restore the OEM firmware, you must firstly dump the OEM firmware from your router before you flash the OpenWrt image. Backup the OEM Firmware ----------------------- The following steps are to be intended for users having little to none experience in linux. Obviously there are many ways to backup the OEM firmware, but probably this is the easiest way for this router. Procedure tested on M31A3.V4300.200420 firmware version. 1) Go to http://192.168.10.1/webcmd.shtml 2) Type the following line in the "Command" input box and then press enter: mkdir /etc_ro/lighttpd/www/dev; cp /dev/mtd0ro /etc_ro/lighttpd/www/dev/mtd0ro; ls -la /etc_ro/lighttpd/www/dev/mtd0ro 3) After few seconds in the textarea should appear this output: -rw-r--r-- 1 0 0 8388608 /etc_ro/lighttpd/www/dev/mtd0ro If your output doesn't match mine, stop reading and ask for help in the forum. 4) Open in another tab http://192.168.10.1/dev/mtd0ro to download the content of the whole NOR. If the file size is 0 byte, stop reading and ask for help in the forum. 5) Come back to the http://192.168.10.1/webcmd.shtml webpage and type: rm /etc_ro/lighttpd/www/dev/mtd0ro; for i in 1 2 3 4 ; do cp /dev/mtd${i}ro /etc_ro/lighttpd/www/dev/mtd${i}ro; done; ls -la /etc_ro/lighttpd/www/dev/ 6) After few seconds, in the textarea should appear this output: -rw-r--r-- 1 0 0 196608 mtd1ro -rw-r--r-- 1 0 0 65536 mtd2ro -rw-r--r-- 1 0 0 65536 mtd3ro -rw-r--r-- 1 0 0 8060928 mtd4ro drwxr-xr-x 7 0 0 0 .. drwxr-xr-x 2 0 0 0 . If your output doesn't match mine, stop reading and ask for help in the forum. 7) Open the following links to download the partitions of the OEM FW: http://192.168.10.1/dev/mtd1ro http://192.168.10.1/dev/mtd2ro http://192.168.10.1/dev/mtd3ro http://192.168.10.1/dev/mtd4ro If one (or more) of these files are 0 byte, stop reading and ask for help in the forum. 8) Store these downloaded files in a safe place. 9) Reboot your router to remove any temporary file in ram. Installation ------------ Flash the initramfs image in the OEM firmware interface (http://192.168.10.1/update.shtml). When Openwrt boots, flash the sysupgrade image otherwise you won't be able to keep configuration between reboots. Restore OEM Firmware -------------------- Flash the "mtd4ro" file you previously backed-up directly from LUCI. Warning: Remember to not keep settings! Warning2: Remember to force the flash. Notes ----- 1) Router mac addresses: LAN XX:XX:XX:XX:XX:9B (factory @ 0x28) WAN XX:XX:XX:XX:XX:9C (factory @ 0x2e) WIFI 2G XX:XX:XX:XX:XX:9D (factory @ 0x04) WIFI 5G XX:XX:XX:XX:XX:9E (factory @ 0x8004) LABEL XX:XX:XX:XX:XX:9D 2) There is just one wifi led for both wifi interfaces. It currently shows only the 2.4 GHz wifi activity. Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* lantiq: fritz736x: Move GPIO resets to the inidvidual board.dts filesMartin Blumenstingl2022-04-164-32/+77
| | | | | | | | | | FRITZ!Box 7360 V2 and FRITZ!Box 7360 SL both use GPIOs 37 (for &phy0) and GPIO 44 (for &phy1) to control the PHY's reset lines. FRITZ!Box 7362 SL however uses GPIO 45 (for &phy0) and GPIO 44 (for &phy1). Move the GPIO reset definitions to each individual board .dts and while at it, fix the GPIOs for the FRITZ!Box 7362 SL. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* kernel: backport ZTE RNDIS bogus MAC address fixLech Perczak2022-04-166-0/+478
| | | | | | | | | | | This is required to support built-in modem of ZTE MF286R, in addition to other external modems, such as MF831, MF910, MF920, which refuse to reconfigure their remote MAC address, even if "locally administered" bit is set, leading to dropped traffic towards the host. Add a workaround for that issue already present in cdc_ether to rndis_host driver as well. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq806x: fix wrong CPU OPP for ipq8062Ansuel Smith2022-04-161-16/+16
| | | | | | | | | Fix wrong CPU OPP for ipq8062. Revision of the SoC added an extra 25mV for every pvs. Also fix the voltage min/max value that were wrong. Reviewed-by: Robert Marko robimarko@gmail.com Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: fix USB bug in 5.10 dtsi additionsRodrigo Balerdi2022-04-161-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The existing device tree has incorrect definitions for usb3_0 and usb3_1 and the blocks they depend upon: their addresses and interrupts are swapped. However, their clocks and resets are not. The result is that the USB blocks are non-functional if only one of them is enabled. This fix backports the definitions from mainline Linux 5.15 to OpenWrt's 5.10 dtsi additions. See the relevant mainline code here: https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148 This fix does not break existing ports. But some ports may have enabled both USB blocks even thought their board only implements one, because enabling a single USB block would not have worked before this fix. This means that revisiting all ports of ipq806x devices that implement a single USB port is advised. This work must be done by maintainers that can determine which USB block corresponds to the implemented port on their hardware. Note that this fix swaps the names of the hardware ports. This is unfortunate, but will happen anyway when switching to kernel 5.15. Thus, it is best to do this ASAP, before users get to depend on port names. It is strongly recommended that this fix is backported to 22.03 before its release. This will minimize the number of users affected by the port name swap. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
* ipq806x: remove non-working fixes for USB bug in 5.10 dtsi additionsRodrigo Balerdi2022-04-162-4/+0
| | | | | | These workarrounds are incomplete and non-functional, and thus not needed. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
* ath79: port HiWiFi HC6361 from ar71xxYousong Zhou2022-04-164-0/+173
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The device was added for ar71xx target and dropped during the ath79 transition, mainly because of the ascii mac address stored in bdinfo partition Device page, http://wiki.openwrt.org/toh/hiwifi/hc6361 The vendor u-boot image accepts sysupgrade.bin image with specific requirements, including having squashfs signature "hsqs" at file offset 0x140000. This is not possible now that OpenWrt kernel image is at least 2MB with the signature at offset 0x240000. Installation of current build of OpenWrt now requires a bootstrap step of installing an earlier version first. - If the vendor u-boot accepts sysupgrade image, hc6361 image of LEDE release should work - If the vendor u-boot accepts only verified flashsmt image, install the one in the above device page. The image is based on Barrier Breaker SHA256SUM of the flashsmt image 81b193b95ea5f8e5c30cd62fa9facf275f39233be4fdeed7038f3deed2736156 After the bootstrap step, current build of OpenWrt can be installed there fine. Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ath79: add nvmem cell mac-address-ascii supportYousong Zhou2022-04-162-0/+206
| | | | | | | This is needed for devices with mac address stored in ascii format, e.g. HiWiFi HC6361 to be ported in the following patch. Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ath79: cleanup mikrotik routerboot partitionsThibaut VARÈNE2022-04-157-12/+6
| | | | | | | | | For some reason useless labels and aliases have been propagated through copy-paste. Before the issue spreads any further, this patch cleans up all relevant DTS files to the canonical form, bringing ath79 in line with other mikrotik platforms (ramips and ipq40xx). Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79: add support for Yuncore A930Thibaut VARÈNE2022-04-152-0/+128
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR - 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN) - 2T2R 802.11b/g/n 2.4GHz Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Clemens Hopfer <openwrt@wireloss.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79: add support for Yuncore XD3200Thibaut VARÈNE2022-04-155-2/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* gemini: Bump kernel to v5.15Linus Walleij2022-04-141-1/+1
| | | | | | | It's working well on all tested targets, so let's move Gemini forward to v5.15. imx is already bumped so why not. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gemini: Create patches and config for kernel v5.15Linus Walleij2022-04-143-0/+588
| | | | | | | | | This creates a v5.15 baseline for the Gemini platform. The main new attraction is the new crypto driver from Corentin Labbe that we activate in the new config. Config was refreshed. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* generic: backport 5.16 RTL8366RB improvementsLinus Walleij2022-04-148-0/+920
| | | | | | | The prerequisite DSA changes for the nice RTL8366RB improvements are already backported so bring back these changes as well. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* mediatek: 5.15: re-enable arch timer on MT7623 as wellDaniel Golle2022-04-141-0/+1
| | | | | | Re-enable arch timer also on MT7623, yet another time. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: 5.15: enable arm arch timer for mt7629Chuanhong Guo2022-04-142-0/+12
| | | | | | otherwise the system delay is completely broken. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* kernel: 5.15: add support for ESMT F50x1G41LBChuanhong Guo2022-04-141-0/+143
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* malta: add config-5.15Daniel Golle2022-04-131-0/+263
| | | | | | | | Adding the kernel configuration has accidentally been omitted when enabling testing kernel 5.15. Add it now. Fixes: 09f6200198 ("malta: enable testing kernel 5.15") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: nand: add 5.15 support for nand subtargetKoen Vandeputte2022-04-131-0/+2
| | | | | | Tested on GL.iNet E750 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: add missing symbols for 5.15Koen Vandeputte2022-04-131-0/+7
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mediatek/mt7622: enable accelerated crypto driversEneas U de Queiroz2022-04-112-0/+20
| | | | | | | | | Use ARMv8 Crypto Extensions for AES, ghash and sha256. This results in a 16 times speed gain in speed for aes-128-ctr, 17x in aes-128-gcm, and 9 times in sha256. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* imagebuilder: export SOURCE_DATE_EPOCH to environmentDaniel Golle2022-04-101-0/+1
| | | | | | | | Export SOURCE_DATE_EPOCH to environment so filesystem and image creation tools will make use of it. Fixes reproducibility of images generated with the ImageBuilder. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.10 to 5.10.110John Audia2022-04-0960-227/+109
| | | | | | | | | | | | | | | | Removed upstreamed: generic/backport-5.10/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch generic/pending-5.10/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch ipq40xx/patches-5.10/105-ipq40xx-fix-sleep-clock.patch All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Compile-/run-tested: ath79/generic (Archer C7 v2). Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.15 to 5.15.33Rui Salvaterra2022-04-0956-342/+122
| | | | | | | | | | | | | | | | | | | | | | Deleted (upstreamed): generic/backport-5.15/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch [1] generic/backport-5.15/730-v5.16-hv-utils-add-PTP_1588_CLOCK-to-Kconfig-to-fix-build.patch [2] generic/pending-5.15/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch [3] generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch [4] Manually rebased: generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch ramips/patches-5.15/710-at803x.patch [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d29cda15cab086d82d692de016f7249545d4b6b4 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d5aad7d63b1b5c1f3c4b69e12c05e7c7d196fae8 [3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=ed750e22e44366e264bcdf7b1cf0713f08f7980a [4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=0fe94b84c43cfea867e1721606185e8686d7d32f Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com> [Refresh patches again] [Remove generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.15 to 5.15.32Rui Salvaterra2022-04-0923-95/+96
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: move some symbols to generic configAleksander Jan Bajkowski2022-04-0913-70/+29
| | | | | | | | | | | | | | | | | | | This commit add some enabled symbols to generic config. LTO is only supported by clang compiler and therefore should be disabled in the generic config instead of duplicating this symbol in each target. CONFIG_LTO_NONE do this job. The second group of symbols is enabled by the options available in the generic config and is therefore added here: * CONFIG_AF_UNIX_OOB is selected by CONFIG_NET && CONFIG_UNIX, * CONFIG_BINARY_PRINTF is selected by CONFIG_BPF_SYSCALL, * CONFIG_NET_SOCK_MSG is selected by CONFIG_BPF_SYSCALL && CONFIG_NET. The other symbols are disabled and should be in the generic config. This commit also removes these symbols from subtargets. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* generic: 5.15: fix aardvak pci pending patchAnsuel Smith2022-04-094-19/+14
| | | | | | | | Fix aardvak pci controller pending patch. Use generic_handle_domain_irq and fix rebase error. Fixes: 483503603cb2 ("generic: 5.15: rework pending patch") Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* armvirt: add 5.15 as testing kernelAleksander Jan Bajkowski2022-04-091-0/+1
| | | | | | Add 5.15 as testing kernel. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* armvirt: move common symbols from subtarget to target configAleksander Jan Bajkowski2022-04-093-12/+6
| | | | | | | These new symbols are common for all subtargets and can be moved into target config. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* armvirt: refresh 5.15 configAleksander Jan Bajkowski2022-04-093-14/+22
| | | | | | | | This was done by executing these commands: $ make kernel_oldconfig CONFIG_TARGET=subtarget $ make kernel_oldconfig CONFIG_TARGET=subtarget_platform Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* armvirt: copy config files from 5.10Aleksander Jan Bajkowski2022-04-093-0/+379
| | | | | | Copy config files from 5.10. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* armvirt: refresh 5.10 configAleksander Jan Bajkowski2022-04-092-1/+2
| | | | | | | | This was done by executing these commands: $ make kernel_oldconfig CONFIG_TARGET=subtarget $ make kernel_oldconfig CONFIG_TARGET=subtarget_platform Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* ipq40xx: add RT-AC2200 alternative name to RT-AC42U/RT-ACRH17Ray Wang2022-04-091-0/+2
| | | | | | RT-AC2200 is the same device with a different name. The OEM firmwares have the same MD5. Signed-off-by: Ray Wang <raywang777@foxmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-15 13:00:41 +0000