aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix pci/pcie related dtc warningsMathias Kresin2018-08-0466-684/+575
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the ranges property to the PCI bridges where missing. Add the unit address to PCI bridge where missing. Rework the complete rt3883 pci node. Drop the PCI unit nodes from the dtsi. They are not used by any dts file and should be rather in the dts than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the pci interrupt controller out of the pci node. It doesn't share the same reg and therefore should be an independent/SoC child node. Move the pci related rt3883 pinctrl setting to the dtsi instead of defining the very same for each rt3883 board. If the device_type property is used for PCI units, the unit is treated as pci bridge which it isn't. Drop it for PCI units. Reference pci-bridges or the pci node defined in the dtsi instead of recreating the whole node hierarchy. It allows to change the referenced node in the dtsi without the need to touch all dts. Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips are the first device on the bus. The unit address has to be the bus address instead of the PCI vendor/device id. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use ralink,nr-gpio instead of ralink,num-gpiosMathias Kresin2018-08-0410-27/+27
| | | | | | | | | | | Since commit c1e7738988f5 ("checks: add gpio binding properties check") dtc treats any *-gpios and *-gpio property as phandle at least during checks. The only whitelisted property is nr-gpio. Use ralink,nr-gpio in favour of ralink,num-gpios to get rid of false positive warnings. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix cpu interrupt controller dtc warningsMathias Kresin2018-08-048-8/+8
| | | | | | | The cpu interrupt controller doesn't have a reg property, hence we can't use a unit address in the node name. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix cpu related dtc warningsMathias Kresin2018-08-049-2/+34
| | | | | | We need a reg property if we are using a unit address. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: convert gpio-export to platform driverRené van Dorst2018-08-043-21/+12
| | | | | | | | | | | | Without this patch you will get an error "gpio-export probe deferral not supported" when you try to export i2c expander gpio pins. gpio-export is probed long before i2c-bus and i2c expander are created and it doesn't retry it so none pins are exported. Signed-off-by: René van Dorst <opensource@vdorst.com> apply the change to all instances of the gpio exports patch Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: really fix TP-Link Archer C7 v2 MAC addressMathias Kresin2018-08-042-2/+1
| | | | | | | | | | | | | | | | | | | | Revert 290c54473ead ("ath79: fix TP-Link Archer C7 v2 wlan1 MAC address") which obviously aims to have a distinct MAC address per interface. Unfortunally it doesn't match what is used by the stock firmware and we shouldn'z use MAC Adresses not reserverd for/assigned to a particular board. The correct MAC adress increments for this board are: wlan0 (5GHz) : -1 wlan1 (2.4GHz) : 0 eth1 (LAN) : 0 eth0 (WAN) : 1 Fixes: FS#408 Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.14 to 4.14.60Koen Vandeputte2018-08-0325-186/+121
| | | | | | | | | | | | Refreshed all patches Removed upstreamed patches: - 500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.117Koen Vandeputte2018-08-039-12/+12
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* sdk: include arch/arm/ Linux includes along with arch/arm64/ onesJo-Philipp Wich2018-08-031-1/+7
| | | | | | | | | | | The Linux headers on arm64 architectures contain references to common arch/arm/ headers which were not bundled by the SDK so far. Check if we're packing the SDK for an arm64 target and if we do, also include arch/arm headers as well. Fixes FS#1725. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* brcm63xx: switch to 4.14Jonas Gorski2018-08-021-1/+1
| | | | | | | Kernel 4.14 support has been present for quite some time, so let's give it wider testing. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: drop b43 from devices with unsupported wifiJonas Gorski2018-08-021-2/+2
| | | | | | | | The internal wifi isn't supported, so drop b43 from devices that only have it. Fixes FS#1698 Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: copy SR102 support patch to 4.14 as wellJonas Gorski2018-08-021-0/+68
| | | | | | | It seems to have been missed when the patch was accepted. Fixes: d59126040701 ("brcm63xx: initial support for Sky SR102 router") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: drop bogus SPROM section from SR102Jonas Gorski2018-08-021-10/+3
| | | | | | | | The integrated SoC wifi will likely never be supported, and if, it will go through DT with the sprom contents there. Fixes: d59126040701 ("brcm63xx: initial support for Sky SR102 router") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar71xx: add support for TP-LINK CPE510 V2.0Andrew Cameron2018-08-022-2/+22
| | | | | | | | Adds Support for the TP-LINK CPE510 V2.0 by TP-Link. The hardware is almost the same as the CPE510 V1.0 Follow the same processes as for the CPE510 V1.0 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* Revert "ar71xx: ag71xx: Prevent kernel oops for board def"Jo-Philipp Wich2018-08-011-15/+1
| | | | | | | | | | | This reverts commit 7a3e133751870a3431e2430386a77a002eb24117. This change reportedly breaks connectivity on some ar71xx devices, so revert it for now. Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087 Reported-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* Revert "ar71xx: ag71xx: Add connect message: fixed phy"Jo-Philipp Wich2018-08-011-7/+0
| | | | | | | | | | | This reverts commit 0b9f4e880807e3cfd22d12b929202e1edcdc577c. This change reportedly breaks connectivity on some ar71xx devices, so revert it for now. Ref: https://github.com/openwrt/openwrt/pull/1217#issuecomment-409708087 Reported-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* Revert "ar71xx: ag71xx_phy: Fix compilation for debug messages"Jo-Philipp Wich2018-08-011-4/+2
| | | | | | | | This reverts commit 2655fbe8efb2a596aa8db92cffa817e3bf0c64ea. The patch introduces syntax errors, revert it for now. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: cr3000: cleanup board definitionDaniel F. Dickinson2018-08-011-16/+23
| | | | | | | | | | | | | 1) Add comments so it's clear why we did things; this may prevent someone (e.g. me) from sinking time into fixing things that aren't broken and/or were done for reason. 2) Drop mdio 0 probe/register; we don't use ag1xx mdio bus 0. 3) Cosmetic reording of some code (tested) that makes the defintion more clear. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cr3000: Use correct company nameDaniel F. Dickinson2018-08-013-3/+3
| | | | | | It's 'PowerCloud Systems' not 'PowerCloud'. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ar71xx: cr3000: Drop support for defunct cloudDaniel F. Dickinson2018-08-011-11/+2
| | | | | | | | | The CR3000 stock firmware is now irrelevant as it required a now defunct cloud service. Therefore only build images that use the entire flash (overwriting stock firwmare-specific partitions that no longer matter), previously called 'nocloud' images. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ath79: Forward port support for CR3000Daniel F. Dickinson2018-08-014-3/+194
| | | | | | | | | | | | | | | | | | | | | | | | The PowerCloud Systems CR3000 was a cloud-managed CPE for a now defunct NaaS offering. It was previously supported under the ar71xx branch and this forward ports that support with some notable differences: 1) Since reverting to stock firmware is now irrelevant there is is only a single openwrt image generated which uses the entire flash rather than preserving PowerCloud-specific partitions that are unneeded to openwrt-- those partitions will be erased and used by the openwrt image. 2) Rather than use a non-standard probe order for the ethernet devices, this image uses a set of 'ip link set ethX name ethY' commands very early in preinit (before the network is used at all), in order to have the the switch and Wan use the same ethernet names as in previous images. 3) /etc/config/wireless will need to be regenerated as the path to the wireless device has changed due to differences in ath79 DT for ar93x compared to ar71xx images. 4) eth0 is wan and eth1 is lan (switch) Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* kernel: bump 4.9 to 4.9.116Koen Vandeputte2018-08-0151-605/+334
| | | | | | | | | | | | | | | | | | | | | | | | | Refreshed all patches Remove upstreamed patches. - 103-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch - 403-mtd_fix_cfi_cmdset_0002_status_check.patch - 001-4.11-01-mtd-m25p80-consider-max-message-size-in-m25p80_read.patch - 001-4.15-08-bcm63xx_enet-correct-clock-usage.patch - 001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch - 900-gen_stats-fix-netlink-stats-padding.patch Introduce a new backported patch to address ext4 breakage, introduced in 4.9.112 - backport-4.9/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch This patch has been slightly altered to compensate for a new helper function introduced in later kernels. Also add ARM64_SSBD symbol to ARM64 targets still running kernel 4.9 Compile-tested on: ar71xx, bcm2710 Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* sdk: bundle usbip userspace sourcesJo-Philipp Wich2018-08-011-0/+4
| | | | | | | | Bundle the usbip utility sources shipped with the Linux kernel tree in order to allow the usbip packages from the package feed to build within the OpenWrt SDK. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* kernel: add missing ARM64_SSBD symbolStijn Tintel2018-07-316-0/+6
| | | | | | | | | In 4.14.57, a new symbol for Spectre v4 mitigation was introduced for ARM64. Add this symbol to all ARM64 targets using kernel 4.14. This mitigates CVE-2018-3639 on ARM64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: remove duplicate #define's in at803x Ethernet PHY driverDaniel Golle2018-07-312-20/+14
| | | | | | | | | | | AT803X_REG_CHIP_CONFIG and AT803X_BT_BX_REG_SEL have been defined upstream by commit f62265b53ef3 ("at803x: double check SGMII side autoneg") An existing local patch then added those exact same defines again which isn't necessary, so remove them. Fixes: f791fb4af450 ("kernel: add linux 4.9 support") Fixes: b3f95490b9be ("kernel: generic: Add kernel 4.14 support") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: re-add patch for AT8032 Ethernet PHYDaniel Golle2018-07-314-11/+81
| | | | | | | | | | The patch was wrongly removed by a kernel version bump to 4.9.105 in the believe that it was merged upstream thow it wasn't. This lead to unrecoverable link losses on devices which use those PHYs such as many ubnt single-port CPEs. Fixes: 7dca1bae82 (kernel: bump to 4.9.105) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: add pending e1000e fixesStijn Tintel2018-07-314-0/+331
| | | | | | | | | | | | | | | The previous round of fixes for the 82574 chip cause an issue with emulated e1000e devices in VMware ESXi 6.5. It also contains changes that are not strictly necessary. These patches fix the issues introduced in the previous series, revert the unnecessary changes to avoid unforeseen fallout, and avoid a case where interrupts can be missed. The final two patches of this series are already in the kernel, so no need to include them here. Patchwork: https://patchwork.ozlabs.org/cover/881776/ Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.14 to 4.14.59Stijn Tintel2018-07-3158-827/+176
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Drop patch that was superseded upstream: ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch Drop upstreamed patches: - apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch - apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch - ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch - brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch - brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch - generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch - generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch - generic/pending/900-gen_stats-fix-netlink-stats-padding.patch In 4.14.55, a patch was introduced that breaks ext4 images in some cases. The newly introduced patch backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch addresses this breakage. Fixes the following CVEs: - CVE-2018-10876 - CVE-2018-10877 - CVE-2018-10879 - CVE-2018-10880 - CVE-2018-10881 - CVE-2018-10882 - CVE-2018-10883 Compile-tested: ath79, octeon, x86/64 Runtime-tested: ath79, octeon, x86/64 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: switch compatible property for RedBoot DT bindingMatt Merhar2018-07-303-3/+3
| | | | | | | | | | | | | | | This changes the DT binding's compatible property to "ecoscentric,redboot-fis-partitions", removing the existing reference to Red Hat. Per the documentation hosted at eCosCentric's website, eCosCentric is RedBoot's sole commercial maintainer since 2002, and the project has been under the stewardship of the Free Software Foundation since 2008. This also updates the property in the Inventel Livebox 1 .dts, the binding's only current user. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* brcm2708: fix w1 patchJohn Crispin2018-07-301-34/+23
| | | | | | this is now part of generic Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: Limit usable channels for OpenMesh A62 PHYsSven Eckelmann2018-07-301-0/+2
| | | | | | | | | The OpenMesh A62 is a tri-band device (1x 2.4GHz, 2x 5GHz) with special filters in front of the RX+TX paths to the 5GHz PHYs. These filtered channel can in theory still be used by the hardware but the signal strength is reduced so much that it makes no sense. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ath79: fix irq assignment for pci-ar71xx driverMatt Merhar2018-07-301-3/+7
| | | | | | | | | | | | | | | | | | In the new DT-based pci-ar71xx driver, ar71xx_pci_irq_init() was being called before populating the PCI controller's device_node struct member. This led to no IRQ being assigned to connected PCI devices (e.g. ath9k cards) and caused them to be non-functional aside from simply being detected. The previous errors encountered in dmesg were: "irq: no irq domain found for /ahb/apb/pcie-controller@180c0000 !". /proc/interrupts listed an IRQ of 0 for the cards. While this has been only been tested on a yet-to-be-merged RouterStation Pro target, it should also fix the broken wifi people have reported for the ath79 WNDR3800 target. Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
* ar71xx: define switch for rb-952ui-5ac2ndThibaut VARÈNE2018-07-301-2/+2
| | | | | | | QCA9533 built-in switch can be configured Tested-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ipq40xx: fix booting secondary CPU coresMantas Pucka2018-07-302-21/+35
| | | | | | | 95672e04 broke booting secondary cores by removing 'qcom,saw' property from L2 cache node. kpssv2_release_secondary() requires it. Signed-off-by: Mantas Pucka <mantas@8devices.com>
* ar71xx: fix TL-WR1043N v5 port mappingJohn Crispin2018-07-301-1/+4
| | | | | | fixes 5660c8fb20 ("ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.") Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: TL-WR1043N v5: fix mapping of LAN ports to labels on housing.Tim Thorpe2018-07-301-1/+1
| | | | | | Reversed the numbering of the LAN ports in Luci so as to match the port numbers on the housing. Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
* ar71xx: TL-WR1043N v4/v5: add orange WAN LED supportTim Thorpe2018-07-301-3/+14
| | | | | | | | | | | Add missing definitions for the orange WAN LED on the TL-WR1043N(D) v4 and v5. Change the name of a MAC address offset constant to make it consistent with the format of the existing constants. Signed-off-by: Tim Thorpe <tim@tfthorpe.net>
* ath79: add support for tl-wr841n-v9Lucian Cristian2018-07-305-1/+175
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ramips: add support for ELECOM WRC-2533GSTINAGAKI Hiroshi2018-07-304-0/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-2533GST is a 2.4/5 GHz band 11ac rotuer, based on MediaTek MT7621A. Specification: - MT7621A (2-Core, 4-Threads) - 128 MB of RAM (DDR3) - 16 MB of Flash (SPI) - 4T4R 2.4/5 GHz wifi - MediaTek MT7615 - 5x 10/100/1000 Mbps Ethernet - 4x LEDs, 6 keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 57600 bps Flash instruction using factory image: 1. Connect the computer to the LAN port of WRC-2533GST 2. Connect power cable to WRC-2533GST and turn on it 3. Access to "https://192.168.2.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click apply ("適用") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* imagebuilder: add function to show manifestPaul Spooren2018-07-301-2/+27
| | | | | | | | | | | | | | | | | | | | | | | | | Tested with 18.06.0-rc2/ar71xx/generic/tl-wdr4300-v1, image & list This PR is based on the work of @fewckert[1] with slight improvements. Add function `manifest` to show the manifest of the produced image, before actually building it. The manifest contains an orderd list of package name and version. This is usefull to check package dependencies but also determine a unique and reproducible image name before building the package. The sysupgrade server[2] builds images on request with individual package selection. To distignish between created images which contain differnt packages, the EXTRA_IMAGE_NAME is set to a shortend hash of the manifest's content. So far the image was renamed afterwards as the manifests content was unknown, however this corrupts the signed sha256sums. This patch allows a clean solution as to dtermine the manifest in advance and set the EXTRA_IMAGE_NAME accordingly. [1]: https://github.com/lede-project/source/pull/1591 [2]: https://github.com/aparcar/attendedsysupgrade-server Signed-off-by: Paul Spooren <mail@aparcar.org>
* x86: add support to set GRUB menu entry titleKjel Delaey2018-07-303-3/+6
| | | | | | | | $ make menuconfig Target Images -> Title for the menu entry in GRUB Signed-off-by: Kjel Delaey <kjel_delaey@hotmail.com>
* kirkwood: add support for Iomega Storcenter ix2-200Ademar Arvati Filho2018-07-307-5/+97
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1000Mhz - Flash-Chip: Hynix NAND - Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16 - RAM: 256MB - LAN: 1x 1000 Mbps Ethernet - WiFi: none - 3x USB 2.0 - UART: for serial console Installation instructions - easy steps: 1. download factory.bin and copy into tftp server 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.13 tftpboot 0x00800000 factory.bin nand erase 0x100000 $(filesize) nand write 0x00800000 0x100000 $(filesize) run bootcmd ``` 3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Installation steps nand bad blocks proof: 1. download initramfs-uImage and copy into usb ext2 partition ``` mkfs.ext2 -L ext2 /dev/sdh1 mount -t ext2 /dev/sdh1 /mnt cp initramfs-uImage /mnt/initramfs.bin umount /mnt ``` 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000 ``` 3. log into openwrt and sysupgrade to install into flash ``` sysupgrade -n /tmp/sysupgrade.bin ``` 4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
* samsung/s5pv210: New targetJianhui Zhao2018-07-309-0/+1148
| | | | Signed-off-by: Jianhui Zhao <jianhuizhao329@gmail.com>
* ar71xx: add support for TP-Link Archer C59 v2Keith Maika2018-07-3012-5/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C59v2 is a dual-band AC1350 router based on Qualcomm/Atheros QCA9561+QCA9886 chips. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - USB 2.0 port - UART header on PCB Flash instruction: - via web UI: 1. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin 2. Login to router and open the Advanced tab 3. Navigate to System Tools -> Firmware Upgrade 4. Upload firmware using the Manual Upgrade form - via TFTP: 1. Set PC to fixed ip address 192.168.0.66 2. Download openwrt-ar71xx-generic-archer-c59-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Keith Maika <keithm@aoeex.com>
* kernel: add missing include to redboot.cRafał Miłecki2018-07-302-2/+10
| | | | | | | | This fixes: drivers/mtd/redboot.c:299:34: error: array type has incomplete element type 'struct of_device_id' Fixes: 5e8b4be53177 ("kernel: add DT binding support to the mtd redboot parser") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* brcm63xx: update DT RedBoot binding for the Inventel Livebox 1Rafał Miłecki2018-07-301-1/+3
| | | | | | | | linux,part-probe should be avoided as its only supported with OpenWrt downstream patch that is going to be dropped eventually. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm47xx: rework model detectionJo-Philipp Wich2018-07-302-18/+25
| | | | | | | | | | | | | | | | | | | | | | | | | On brcm47xx boards, the model ID is the combination of the "boardtype" nvram variable and an optional supplemental "boardnum" variable while the human readable model name is usually exposed in the "machine" field of the /proc/cpuinfo file. Move the extraction of the board nvram variables and model name string into the 01_sysinfo file and rework the 01_detect board configuration script to solely use the prepared sysinfo values without performing own detection logic. As a consequence, we can drop the ucidef_set_board_id() and ucidef_set_model_name() invocations in favor to the generic behaviour which copies the /tmp/sysinfo/{board_name,model} values into the board.json "id" and "name" fields respectively. Since "01_detect" only contains network configuration logic after this change, move it to "01_network" and rename the contained "detect_by_xxx" functions to "configure_by_xxx" instead, to avoid potential confusion. Fixes FS#1576 Acked-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* omap: disable ubifsLucian Cristian2018-07-301-1/+1
| | | | | | ubifs image are not working, until there is a fix, disable them Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* omap: add support for f2fs/ext4 overlay creationLucian Cristian2018-07-303-0/+12
| | | | | | add kernel support and include the tools for creating an overlay partition (f2fs or ext4) Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* omap: add sysupgrade supportLucian Cristian2018-07-302-0/+109
| | | | | | add sysupgrade missing script files Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-14 18:59:30 +0000