aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: add support for Cisco Meraki MR42/MR52Matthew Hagan2021-11-289-1/+755
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MR42 and MR52 are two similar IPQ806x based devices from the Cisco Meraki "Cryptid" series. MR42 main features: - IPQ8068 1.4GHz - 512MB RAM - 128MB NAND - 2x QCA9992 (2.4 & 5GHz) - 1x QCA9889 (2.4 & 5GHz) - 1x AR8033 PHY - PoE/AC power MR52 main features: - IPQ8068 1.4GHz - 512MB RAM - 128MB NAND - 2x QCA9994 (2.4 & 5GHz) - 1x QCA9889 (2.4 & 5GHz) - 2x AR8033 PHYs - PoE/AC power (MR42 Only) Installation via diagnostic mode: If you can successfully complete step 1 then you can continue to install via this method without having to open the device. Otherwise please use the standard UART method. Please note that when booting via TFTP, some Ethernet devices, in particular those on laptops, will not connect in time, resulting in TFTP boot not succeeding. In this instance it is advised to connect via a switch. 1. Hold down reset at power on and keep holding, after around 10 seconds if the orange LED changes behaviour to begin flashing, proceed to release reset, then press reset two times. Ensure that the LED has turned blue. Note that flashing will occur on some devices, but it will not be possible to change the LED colour using the reset button. In this case it will still be possible to continue with this install method. 2. Set your IP to 192.168.1.250. Set up a TFTP server serving mr42_u-boot.mbn and openwrt-ipq806x-generic-meraki_mr42-initramfs-fit-uImage.itb, obtained from [1]. 3. Use telnet and connect to 192.168.1.1. Run the following commands to install u-boot. Note that all these commands are critical, an error will likely render the device unusable. Option 3.1: If you are sure you have set up the TFTP server correctly you can run this script on the device. This will download and flash the u-boot image immediately: `/etc/update_uboot.sh 192.168.1.250 mr42_u-boot.mbn` Once completed successfully, power off the device. Option 3.2: If you are unsure the TFTP server is correctly set up you can obtain the image and flash manually: 3.2.1. `cd /tmp` 3.2.2. `tftp-hpa 192.168.1.250 -m binary -c get mr42_u-boot.mbn` 3.2.3. Confirm file has downloaded correctly by comparing the md5sum: `md5sum mr42_u-boot.mbn` 3.2.4. The following are the required commands to write the image. `echo 1 > /sys/devices/platform/msm_nand/boot_layout mtd erase /dev/mtd1 nandwrite -pam /dev/mtd1 mr42_u-boot.mbn echo 0 > /sys/devices/platform/msm_nand/boot_layout` Important: You must observe the output of the `nandwrite` command. Look for the following to verify writing is occurring: `Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000` If you do not see this then do not power off the device. Check your previous commands and that mr42_u-boot.mbn was downloaded correctly. Once you are sure the image has been written you can proceed to power off the device. 4. Hold the reset button and power on the device. This will immediately begin downloading the appropriate initramfs image and boot into it. Note: If the device does not download the initramfs, this is likely due to the interface not being brought up in time. Changing Ethernet source to a router or switch will likely resolve this. You can also try manually setting the link speed to 10Mb/s Half-Duplex. 5. Once a solid white LED is displayed on the device, continue to the UART installation method, step 6. Standard installation via UART - MR42 & MR52 1. Disassemble the device and connect a UART header. The header pinout is as follows: 1 - 3.3v 2 - TXD 3 - RXD 4 - GND Important: You should only connect TXD, RXD and GND. Connecting 3.3v may damage the device. 2. Set your IP to 192.168.1.250. Set up a TFTP server serving openwrt-ipq806x-generic-meraki_(mr42|mr52)-initramfs-fit-uImage.itb. Separately obtain the respective sysupgrade image. 3. Run the following commands, preferably from a Linux host. The mentioned files, including ubootwrite.py and u-boot images, can be obtained from [1]. `python ubootwrite.py --write=(mr42|mr52)_u-boot.bin` The default for "--serial" option is /dev/ttyUSB0. 4. Power on the device. The ubootwrite script will upload the image to the device and launch it. The second stage u-boot will in turn load the initramfs image by TFTP, provided the TFTP server is running correctly. This process will take about 13 minutes. Once a solid white LED is displayed, the image has successfully finished loading. Note: If the image does not load via TFTP, try again with the Ethernet link to 10Mb/s Half-Duplex. 5. (MR42 only) Do not connect over the network. Instead connect over the UART using minicom or similar tool. To replace u-boot with the network enabled version, please run the following commands. Note that in the provided initramfs images, the u-boot.mbn file is located in /root: If you have not used the provided initramfs, you must ensure you are using an image with "boot_layout" ECC configuration enabled in the Kernel. This will be version 5.10 or higher. If you do not do this correctly the device will be bricked. `insmod mtd-rw i_want_a_brick=1 mtd erase /dev/mtd8 nandwrite -pam /dev/mtd8 /root/mr42_u-boot.mbn` After running nandwrite, ensure you observe the following output: `Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000` 6. (Optional) If you have no further use for the Meraki OS, you can remove all other UBI volumes on ubi0 (mtd11), including diagnostic1, part.old, storage and part.safe. You must not remove the ubi1 ART partition (mtd12). `for i in diagnostic1 part.old storage part.safe ; do ubirmvol /dev/ubi0 -N $i done` 7. Proceed to flash the sysupgrade image via luci, or else download or scp the image to /tmp and use the sysupgrade command. [1] The mentioned images and ubootwrite.py script can be found in this repo: https://github.com/clayface/openwrt-cryptid [2] The modified u-boot sources for the MR42 and MR52 are available: https://github.com/clayface/U-boot-MR52-20200629 Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq806x: add gsbi2_i2c labelMatthew Hagan2021-11-281-0/+9
| | | | | | gsbi2_i2c is used by the Meraki MR42 so we need to expose a label here. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq806x: backport GMAC_AHB_RESET deassert patchesMatthew Hagan2021-11-282-0/+139
| | | | | | | | | Add backports of the following patches: "net: stmmac: explicitly deassert GMAC_AHB_RESET" and "ARM: dts: qcom: add ahb reset to ipq806x-gmac" Required for Meraki MR42/MR52. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq806x: add GSBI nodes to ipq8064-dtsi-addidionsMatthew Hagan2021-11-283-51/+96
| | | | | | | | | Rather than having separate patches for each GSBI node added, this patch consolidates the existing GSBI1 patch into 083-ipq8064-dtsi-additions.patch. In addition, GSBI6 and GSBI7 I2C nodes, required for the MR42 and MR52 respectively, are added. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq40xx: add support for MikroTik hAP ac3Robert Marko2021-11-289-5/+392
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD (hAP ac³), a indoor dual band, dual-radio 802.11ac wireless AP with external omnidirectional antennae, USB port, five 10/100/1000 Mbps Ethernet ports and PoE passthrough. See https://mikrotik.com/product/hap_ac3 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4019 - RAM: 256 MB - Storage: 16 MB NOR + 128 MB NAND - Wireless: · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in, PoE passtrough on port 5 - 1x USB Type A port Installation: 1. Boot the initramfs image via TFTP 2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1" 3. Use ubiformat to remove MikroTik specific UBI volumes * Detach the UBI partition by running: "ubidetach -d 0" * Format the partition by running: "ubiformat /dev/mtdN -y" Replace mtdN with the correct mtd index from step 2. 3. Flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com> Tested-by: Mark Birss <markbirss@gmail.com> Tested-by: Michael Büchler <michael.buechler@posteo.net> Tested-by: Alex Tomkins <tomkins@darkzone.net>
* kernel: bump 5.4 to 5.4.162John Audia2021-11-2816-42/+43
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/mt7621* *I am hit with the binutils 2.37 bug so I had to revert 7f1edbd41295dff9f2127b169fbc086c0fb2c14e in order to downgrade to 2.35.1 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.4 to 5.4.161John Audia2021-11-2830-118/+64
| | | | | | | | | | | | | | | Removed upstreamed: ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch[1] Manually rebased: layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch All other patches automatically rebased. 1. Private email exchange with patch author, Hauke Mehrtens Signed-off-by: John Audia <graysky@archlinux.us>
* gemini: try fis-index-block with 128 KiB sectorsChristian Lamparter2021-11-281-0/+52
| | | | | | | | | | | | | Steven Maddox reported in the OpenWrt bugzilla, that his RaidSonic IB-NAS4220-B was no longer booting with the new OpenWrt 21.02 (uses linux 5.10's device-tree). However, it was working with the previous OpenWrt 19.07 series (uses 4.14). (This is still under investigation.) Bugzilla: https://bugs.openwrt.org/index.php?do=details&task_id=4137 Reported-by: Steven Maddox <s.maddox@lantizia.me.uk> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: utilize nvmem on Netgear EX61X0 v2 SeriesChristian Lamparter2021-11-282-10/+27
| | | | | | | | the Netgear EX6100v2 and EX6150v2 can utilize the nvmem for the pre-calibration and mac-address for both WIFI devices. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert TP-Link Archer C7v1/2 Wifis to nvmem-cellsChristian Lamparter2021-11-283-10/+38
| | | | | | | | | | | | | | | For v2, both ath9k (2.4GHz Wifi) and ath10k (5 GHz) driver now pull the (pre-)calibration data from the nvmem subsystem. v1 is slightly different as only the ath9k Wifi is supported. This allows us to move the userspace caldata extraction and mac-address patching for the 5GHZ ath10k supported wifi into the device-tree definition of the device. ath9k's nodes are also changed over to use nvmem-cells over OpenWrt's custom mtd-cal-data property. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: backport "fix oops when CONFIG_FSL_PMC=n"Christian Lamparter2021-11-281-0/+55
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Martin Kennedy reported: |Presently, I get this kernel panic on mpc85xx (Aerohive HiveAP 370) |on OpenWrt 'master' which occurs right as the second processor is |initialized: | |[ 0.478804] rcu: Hierarchical SRCU implementation. |[ 0.535569] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build |[ 0.627233] smp: Bringing up secondary CPUs ... |[ 0.681659] kernel tried to execute user page (0) - exploit attempt? (uid: 0) |[ 0.766618] BUG: Unable to handle kernel instruction fetch (NULL pointer?) |[ 0.848899] Faulting instruction address: 0x00000000 |[ 0.908273] Oops: Kernel access of bad area, sig: 11 [#1] |[ 0.972851] BE PAGE_SIZE=4K SMP NR_CPUS=2 P1020 RDB |[ 1.031179] Modules linked in: |[ 1.067640] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.80 #0 |[ 1.139507] NIP: 00000000 LR: c0021d2c CTR: 00000000 |[ 1.199921] REGS: c1051cf0 TRAP: 0400 Not tainted (5.10.80) |[...] |[ 1.758220] NIP [00000000] 0x0 |[ 1.794688] LR [c0021d2c] smp_85xx_kick_cpu+0xe8/0x568 |[ 1.856126] Call Trace: |[ 1.885295] [c1051da8] [c0021cb8] smp_85xx_kick_cpu+0x74/0x568 (unreliable) |[ 1.968633] [c1051de8] [c0011460] __cpu_up+0xc0/0x228 |[ 2.029038] [c1051e18] [c0031bbc] bringup_cpu+0x30/0x224 |[ 2.092572] [c1051e48] [c0031f3c] cpu_up.constprop.0+0x180/0x33c |[..] |[ 2.727952] ---[ end trace 9b796a4bafb6bc14 ]--- |[ 3.800879] Kernel panic - not syncing: Fatal exception |[ 3.862353] Rebooting in 1 seconds.. |[ 5.905097] System Halted, OK to turn off power | |I bisected this down to commit 3ae5da5adce9 ("kernel: bump 5.10 to 5.10.80"); |that is, I don't get the panic right before this commit, but I do after. He reported the issue upstream and Xiaoming Ni from huawei came up with the patch (that is on it's way to upstream). While the AP370 is not in Openwrt, this will likely affect other SMP P1020 devices OpenWrt ships with: like the AP330, Enterasys WS-AP3710i, etc. Reported-by: Martin Kennedy <hurricos@gmail.com> Tested-by: Martin Kennedy <hurricos@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: purge clk_ignore_unused bootargChristian Lamparter2021-11-272-2/+2
| | | | | | | | | these flags have been creeping in from the QSDK. All needed clocks should be accounted for, and if a device is broken due to this. It should be looked into. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: update 105-ipq40xx-fix-sleep-clock.patchChristian Lamparter2021-11-271-13/+10
| | | | | | Bjorn Anderson has suggestions which would help to upstream the patch. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* lantiq: set maximum kernel size for P2812HNUF3Mathias Kresin2021-11-271-0/+2
| | | | | | | | | | | The board has a fixed size kernel partition but do not limit the kernel size during image building. Disable image building for both boards as well, since the kernel of the last release as well as master are to big to fit into the 2 MByte kernel partition. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop kernel 5.4 supportAleksander Jan Bajkowski2021-11-2734-11702/+0
| | | | | | | | The current state of the kernel 5.4 support is in the openwrt-21.02 branch. No need to keep a not default used kernel in this branch. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [VRX268/ bthub5]
* lantiq: switch to kernel 5.10Aleksander Jan Bajkowski2021-11-271-1/+1
| | | | | | | Use kernel 5.10 by default. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [VRX268/ bthub5]
* lantiq: ar7: use okli loader for FRITZ!BoxMathias Kresin2021-11-274-3/+46
| | | | | | | | | | With Kernel 5.10 the ar7 FRITZ!Box are not booting the initramfs nor the sysupgrade image any more. Presumably due to the grown kernel. Use the okli preloader to workaround the bootloader issue. No solution so far for the initramfs. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: bring back okli loaderMathias Kresin2021-11-2719-0/+2004
| | | | | | | | | | | | | Removed due to being unused with 1f7a03a70603, but now required for the ar7 FRITZ!Box. Could be used for the ARV7519RW22 as well, for which the image generation was disabled due to a stock u-boot issue with kernel bigger than 2 MByte. The code is combination of the ath79 and ramips okli loader. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 5.10 to 5.10.82John Audia2021-11-2719-94/+38
| | | | | | | | | | | | | | | | Removed upstreamed: bcm53xx/patches-5.10/033-v5.16-0014-ARM-dts-NSP-Fix-mpcore-mmc-node-names.patch Manually rebased: ipq806x/patches-5.10/086-ipq8064-fix-duplicate-node.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.81John Audia2021-11-278-12/+12
| | | | | | | | | | | | | Manually rebased: octeontx/patches-5.10/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* llvm-bpf: fix rebuild check for generating tarballFelix Fietkau2021-11-261-1/+1
| | | | | | Check the version file, as it will be regenerated on rebuild Signed-off-by: Felix Fietkau <nbd@nbd.name>
* llvm-bpf: use SOURCE_DATE_EPOCH for generated tarballFelix Fietkau2021-11-261-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* realtek: Remove _machine_restart and _machine_haltSander Vanheule2021-11-241-85/+0
| | | | | | | | | | | | | | By dropping _machine_restart, users can provide more reliable or device-specific restart modes. _machine_halt was already removed in commit f4b687d1f053 ("realtek: use kernel defined halt"), but quietly reintroduced in commit 8faffa00cb6b ("realtek: add support for the RTL9300 timer"). Let's remove it again. Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Paul Fertser <fercerpav@gmail.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: Add and enable watchdog nodeSander Vanheule2021-11-243-1/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add and enable the Realtek Otto WDT peripheral found on these SoCs. Default all devices to use standard (cold) reboot and "soc" resets. Devices that require the PLL value fixup before restarting, should pick the "cpu" or "software" reset mode. These devices also need to provide a custom reboot mode, by adding the reboot argument to the kernel command line: WDT reset mode | kernel reboot mode ----------------+--------------------------------------- soc | reboot=cold (default if not specified) cpu | reboot=warm software | reboot=software Preferrably, these devices should use an alternative restart method like gpio-restart to provide reliable restarts. Note that watchdog restarts are not yet exposed, since the _machine_restart override is still present. Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Paul Fertser <fercerpav@gmail.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: Backport Realtek Otto WDT driverSander Vanheule2021-11-243-0/+486
| | | | | | | | | | | Add patch submitted upstream to linux-watchdog and replace the MIPS architecture symbols. Requires one extra patch for the DIV_ROUND_* macros, which have moved to a different header since 5.10. Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Paul Fertser <fercerpav@gmail.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: Add Lexra bus clockSander Vanheule2021-11-242-8/+13
| | | | | | | | | | | | | | | | | The CPU peripherals on RTL83xx/RTL930x are connected to the CPU via the Lexra bus. This bus can provide a clock signal to these peripherals, but no clock driver is currently available. Instead, use a fixed-clock to provide the clock frequency, and update the dependent peripherals. Lexra bus clock frequencies: - RTL838x: 200MHz - RTL839x: 200MHz - RTL930x: 175MHz Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Paul Fertser <fercerpav@gmail.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: Consolidate bootargsSander Vanheule2021-11-248-26/+2
| | | | | | | | | | All current devices use identical bootargs, so let's move that to the common devicetree includes. Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Paul Fertser <fercerpav@gmail.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: reset both ethernet NIC and queuesSander Vanheule2021-11-241-4/+7
| | | | | | | | | | | | | | | Recent versions of Realtek's SDK reset both the ethernet NIC and queues (SW_NIC_RST and SW_Q_RST bits) when initialising the hardware. Furthermore, when issuing a CPU reset on the Zyxel GS1900-8 (not supported by any current driver), the networking part of the SoC is not reset. This leads to unresponsive network after the restart. By resetting both the ethernet NIC and queues, networking always comes up reliably. Suggested-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* bcm53xx: fix platform clocks & USB 2.0 PHYRafał Miłecki2021-11-231-0/+62
| | | | | | | | This fixes WARNing, missing clocks and [ 10.422481] bcm_ns_usb2 1800c164.usb2-phy: Clock not defined Fixes: 5901917b936d ("bcm53xx: use more upsteam DT patches from 5.16 / 5.17") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: use new USB 2.0 PHY bindingRafał Miłecki2021-11-232-0/+183
| | | | | | | | | | | This fixes: [ 10.440495] bcm_ns_usb2 1800c000.usb2-phy: can't request region for resource [mem 0x1800c000-0x1800cfff] [ 10.450039] bcm_ns_usb2 1800c000.usb2-phy: Failed to map DMU regs [ 10.456183] bcm_ns_usb2: probe of 1800c000.usb2-phy failed with error -16 caused by conflict in allocating resources. Fixes: f55f1dbaad33 ("bcm53xx: switch to the kernel 5.10") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* Revert "ath79: add support for Mikrotik LHG 5"Hauke Mehrtens2021-11-236-177/+0
| | | | | | | | This reverts commit 48774decea9b42e97edd53ce33e574de7d85f3df. This commit does not contain a valid name in the Signed-off-by line. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm53xx: specify switch ports on TP-LINK devicesRafał Miłecki2021-11-221-0/+92
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* tools/llvm-bpf: move tarball packing to target/llvm-bpfFelix Fietkau2021-11-222-2/+36
| | | | | | | This ensures that the tarball is regenerated after make clean or after switching to a different target Signed-off-by: Felix Fietkau <nbd@nbd.name>
* sunxi: build kernel with sun6i-rtc driverDaniel Golle2021-11-212-0/+2
| | | | | | | | | | | | | | | | | sun6i-rtc cannot be built as a module and the hardware is only present in some of the sunxi SoCs, see driver source: { .compatible = "allwinner,sun6i-a31-rtc" }, { .compatible = "allwinner,sun8i-a23-rtc" }, { .compatible = "allwinner,sun8i-h3-rtc" }, { .compatible = "allwinner,sun8i-r40-rtc" }, { .compatible = "allwinner,sun8i-v3-rtc" }, { .compatible = "allwinner,sun50i-h5-rtc" }, { .compatible = "allwinner,sun50i-h6-rtc" }, Set CONFIG_RTC_DRV_SUN6I=y in kernel config file for cortexa7 and cortexa53 subtargets which covers all of the above. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Revert "sunxi: add rtc-sun6i driver package"Daniel Golle2021-11-211-18/+0
| | | | | | | sun6i-rtc is a builtin_platform_driver and cannot be built as a module. Hence this reverts commit e178d9a5494747a9b6ea34f2fc9e798b4b1ecc16. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: fix ralink_i2s_debugfs_remove declarationEneas U de Queiroz2021-11-202-2/+2
| | | | | | | Correct ralink_i2s_debugfs_remove declaration in ralink patches when CONFIG_DEBUG_FS is not selected. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
* ramips: use lzma-loader on D-Link DIR-615 H1Mirko Parthey2021-11-201-0/+1
| | | | | | | Fixes the boot loader LZMA decompression issue: LZMA ERROR 1 - must RESET board to recover Signed-off-by: Mirko Parthey <mirko.parthey@web.de>
* ramips: add support for Wavlink WL-WN576A2Thomas Aldrian2021-11-204-2/+201
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles repeater / router. It is also sold under the name SilverCrest SWV 733 B1. Device specs: - CPU: MediaTek MT7628AN - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 1x 10/100 Mbps - 2.4 GHz: b/g/n SoC - 5 GHz: a/n/ac MT7610EN - Buttons: WPS, reset, sliding switch (ap/repeater) - LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS Flashing: U-Boot launches a TFTP client if WPS button is held during boot. - Server IP: 192.168.10.100 - Firmware file name: firmware.bin Device will reboot automatically. First boot takes about 90s. Coelner (waenger@gmail.com) is the original author, but I have made some fixes. He does not wish to sign off using his real name. Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
* ath79: merge D-Link DAP-2695 with dtsiSebastian Schaper2021-11-202-81/+25
| | | | | | | | | | | | Further devices from the series have been added in the meantime, introducing `qca955x_dlink_dap-2xxx.dtsi`. Thus, merge support for DAP-2695 with the existing dtsi. This implies factory images can now be flashed via the regular OEM Web UI, as well as the bootloader recovery. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: move cal-data extraction to dts for DAP-2695Sebastian Schaper2021-11-203-5/+2
| | | | | | | | | | This device can be merged with the existing dtsi, which declares the location of ath9k cal-data via devicetree, correcting the 2.4G mac address in `10_fix_wifi_mac` rather than `10-ath9k-eeprom`. To make these changes more visible, apply before merging with dtsi. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* ath79: increase SPI frequency for D-Link DAP-2695Sebastian Schaper2021-11-201-1/+1
| | | | | | | | | This device can be merged with the existing dtsi, which will increase spi-max-frequency to 50 MHz. To make this change more visible, increase to 50 MHz before merging. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
* omap: switch to kernel 5.10Andre Heider2021-11-201-1/+1
| | | | Signed-off-by: Andre Heider <a.heider@gmail.com>
* omap: update kernel 5.10 configAndre Heider2021-11-201-88/+29
| | | | | | | | | | | | | | | | | | | Manually set toggles are: MMC_SDHCI_OMAP=y TI_PRUSS_INTC=y DRM_TI_TPD12S015=y (successor to DRM_OMAP_ENCODER_TPD12S015 [0] [1]) DRM_DISPLAY_CONNECTOR=y (for DRM_TI_TPD12S015 [1]) DRM_SIMPLE_BRIDGE=y (for DRM_TI_TPD12S015 [1]) Manually unset toggles are: SND_MIXER_OSS=y (disabled by generic config) The rest was automatically modified by the kernel_oldconfig make target. [0] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=cff5e6f7e83f6271ed75972e9a2920e2c7f62d6c [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e7e67d9a2f1dd2f938adcc219b3769f5cc3f0df7 Signed-off-by: Andre Heider <a.heider@gmail.com>
* omap: copy kernel 5.4 config for 5.10Andre Heider2021-11-201-0/+740
| | | | Signed-off-by: Andre Heider <a.heider@gmail.com>
* ath79: add support for Mikrotik LHG 5Jakob (Jack/XDjackieXD)2021-11-206-0/+177
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi integrated antenna built around the Atheros AR9344 SoC. It is very similar to the SXT Lite5 series which this patch is based upon. Specifications: - SoC: Atheros AR9344 - RAM: 64 MB - Storage: 16 MB SPI NOR - Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2 - Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port, 8-32 Vdc PoE in - 8 user-controllable LEDs: - 1x power (blue) - 1x user (white) - 1x ethernet (green) - 5x rssi (green) See https://mikrotik.com/product/RBLHG-5nD for more details. Notes: The device was already supported in the ar71xx target. Flashing: TFTP boot initramfs image and then perform a sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Signed-off-by: Jakob (Jack/XDjackieXD) <jakob@chaosfield.at>
* sunxi: add rtc-sun6i driver packageZhao Yu2021-11-201-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | AP6212 wifi need wifi_pwrseq, but from OrangePi Lite 2 dts : wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; clocks = <&rtc 1>; clock-names = "ext_clock"; reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */ post-power-on-delay-ms = <200>; }; this pwrseq need rtc clock, or kernel won't find this device. but now rtc-sunxi.c only support A10/A20. Orangepi Lite 2 use H6 ,from rtc-sun6i.c show compatible is { .compatible = "allwinner,sun6i-a31-rtc" }, { .compatible = "allwinner,sun8i-a23-rtc" }, { .compatible = "allwinner,sun8i-h3-rtc" }, { .compatible = "allwinner,sun8i-r40-rtc" }, { .compatible = "allwinner,sun8i-v3-rtc" }, { .compatible = "allwinner,sun50i-h5-rtc" }, { .compatible = "allwinner,sun50i-h6-rtc" }, So it need this to let kernel find this mmc wifi device. As suggested by hauke, let it build as package. Signed-off-by: Zhao Yu <574249312@qq.com>
* ath79: mikrotik: enable USB module on RouterBoard wAPR-2nDRoger Pueyo Centelles2021-11-202-1/+9
| | | | | | | | | | | The MikroTik RouterBOARD wAPR-2nD (wAP R) router features a miniPCI-e slot with USB lines connected, which are used by some USB cards with miniPCI-e form factor, like the R11e-LR8. Enabling USB support is required for such cards to work. Tested on a MikroTik wAP LR8 kit (RB wAPR-2nD + R11e-LR8). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* octeon: add USB3 support (for Ubiquiti EdgeRouter 6P)Laurent DEBOMY2021-11-202-0/+4
| | | | | | Fixes: FS#4086 Signed-off-by: Laurent DEBOMY <laurent.debomy@canal-belletrud.fr>
* mvebu: backport mvneta basic MQPrio patchKabuli Chana2021-11-201-0/+109
| | | | | | | Implement a basic MQPrio support, inserting rules in RX that translate the TC to prio mapping into vlan prio to queues. Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
* kernel: bump 5.4 to 5.4.159John Audia2021-11-203-6/+6
| | | | | | | | | Manually rebased: generic-backport/850-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch All other patches automatically rebased. Signed-off-by: John Audia <graysky@archlinux.us>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-25 20:58:33 +0000