aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* mediatek: mt7623: include regular AHCI PCI driverDaniel Golle2022-01-251-1/+1
| | | | | | | | | The legacy image for the UniElec U7623-02 until now included kmod-ata-ahci-mtk. The MT7623 chip doesn't have that IP and that board uses a PCIe-connected AHCI controller for the SATA port and mSATA-pins of the mPCIe socket. Hence include kmod-ata-ahci instead. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: drop 5.4 kernelRobert Marko2022-01-2448-7415/+0
| | | | | | | Since 5.10 is now default, no point in keeping 5.4 around. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* mediatek: store random MAC address in U-Boot env on first bootDaniel Golle2022-01-231-0/+14
| | | | | | | For devboards without a MAC address assigned from factory, store the random MAC in U-Boot env on first boot to make it persistent. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uboot-envtools: add configuration for UniElec U7623 boardDaniel Golle2022-01-231-5/+5
| | | | | | | Add U-Boot env settings to allow accessing the environment using fw_printenv and fw_setenv tools on the UniElec U7623 board. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7623: rework images for U7623-02 boardDaniel Golle2022-01-2313-313/+95
| | | | | | | | | | | | | | | | | | | | | | Users of older OpenWrt versions need sysupgrade using the *emmc.img.gz file once which will upgrade U-Boot and switch to the new image layout. Users of the vendor firmware need to first flash the legacy image to then sunsequently carry out a full-flash upgrade. Alternatively the board can also be flashed using MediaTek's proprietary SP Flash Tool. Configuration as well as persistent MAC address will be lost once at this point and you will have to redo (or restore) all configuration manually. To restore the previous persistent MAC address users may set it manually using fw_setenv ethaddr 00:11:22:33:44:55 For future upgrades once running OpenWrt past this commit, the usual *sysupgrade.itb file can be used. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add common DTS aliases for UniElec U7623 boardDaniel Golle2022-01-231-2/+8
| | | | | | | | * Use serial0 instead of serial2 for the only serial port * Add LED aliases * Add ethernet0 alias to inherit ethaddr from U-Boot env Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uml: make use of 'rootfs-part' featureDaniel Golle2022-01-231-1/+1
| | | | | | | Use 'rootfs-part' feature instead of referencing the TARGET_uml in Config-images.in. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* sunxi: make use of 'rootfs-part' featureDaniel Golle2022-01-231-1/+1
| | | | | | | Use 'rootfs-part' feature instead of referencing the TARGET_sunxi in Config-images.in. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* omap: make use of 'rootfs-part' featureDaniel Golle2022-01-231-1/+1
| | | | | | | Use 'rootfs-part' feature instead of referencing the TARGET_omap in Config-images.in. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: use CONFIG_TARGET_ROOTFS_PARTSIZEDaniel Golle2022-01-233-5/+5
| | | | | | | Enable 'rootfs-part' feature to make the size of the partition of the production image configurable instead of hard-coding it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: add support for GL.iNet GL-XE300Victorien Molle2022-01-222-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GL.iNet GL-XE300 is a 4G LTE Wireless router, based on QCA9531 SoC. Specifications: - SoC: QCA9531 (650MHz) - RAM: DDR2 128M - Flash: SPI NOR 16M + SPI NAND 128M - WiFi: 2.4GHz with 2 antennas - Ethernet: - 1x LAN (10/100M) - 1x WAN (10/100M) - LTE: - USB: 1x USB 2.0 port - UART: - 3.3V, TX, RX, GND / 115200 8N1 MAC addresses as verified by OEM firmware: use address source LAN *:c5 art 0x0 (label) WAN *:c6 label + 1 WLAN *:c7 art 0x1002 Installation via U-Boot rescue: 1. Press and hold reset and power buttons simultaneously 2. Wait for the LAN led to blink 5 times 3. Release reset and power buttons 4. The rescue page is accessible via http://192.168.1.1 5. Select the OpenWrt factory image and start upgrade 6. Wait for the router to flash new firmware and reboot Revert to stock firmware: i. Download the stock firmware from GL.Inet website ii. Use the same method explained above to flash the stock firmware Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr> [update commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: correct vendor name for COMFAST/JoowinRodrigo Araujo2022-01-227-44/+50
| | | | | | | | | | | | | | | | When Joowin WR758AC V1 and V2 devices were added, they should have been added with the primary manufacturer name which is COMFAST, since Joowin is just an alternate vendor name on some coutries or stores. Fix this by changing the the vendor name on the respective files and set Joowin as ALT0 variants while ensuring compatibility for early users. Also adjust the model names to better follow the naming rules. As a side effect, fix mt76x8 network script which was left incorrectly unsorted on the case block conditions. Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2") Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
* ramips: read Tenbay T-MB5EU address from single locationDavid Bauer2022-01-221-5/+2
| | | | | | | | | | | | | Currently the WAN MAC address is read from a different offset contrary to all other addresses. There's conflicting information whether offset 0x28 on the factory partition contains the valid WAN mac for all devices while 0x4 seems to be uniform. Read the WAN mac from this location and calculate it. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: update Tenbay T-MB5EU wireless MAC addressDavid Bauer2022-01-221-2/+1
| | | | | | | | | | | | | | The current MAC address assignment is still incorrect. Use the same MAC address as seen on the stock firmware for both wireless interfaces. The 5GHz MAC address OUI is +2 in the first EUI octet. We currently don't do this in OpenWrt. Ignore this offset for now. With the current assignment, recurring MAC addresses between radios is already taken care of. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq806x: Netgear D7800: Fix RAM and enable PCIe #2David Woodhouse2022-01-211-1/+15
| | | | | | | This board has 512MiB of RAM like the R7800, and the VDSL modem is attached to the second PCIe port. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* ath79: add support for reset key on MikroTik RB912UAG-2HPnDDenis Kalashnikov2022-01-197-8/+282
| | | | | | | | | | | | | | | | | | | | | | On MikroTik RB91x board series a reset key shares SoC gpio line #15 with NAND ALE and NAND IO7. So we need a custom gpio driver to manage this non-trivial connection schema. Also rb91x-nand needs to have an ability to disable a polling of the key while it works with NAND. While we've been integrating rb91x-key into a firmware, we've figured out that: * In the gpio-latch driver we need to add a "cansleep" suffix to several gpiolib calls, * When gpio-latch and rb91x-nand fail to get a gpio and an error is -EPROBE_DEFER, they shouldn't report about this, since this actually is not an error and occurs when the gpio-latch probe function is called before the rb91x-key probe. We fix these related things here too. Signed-off-by: Denis Kalashnikov <denis281089@gmail.com> Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* layerscape: switch to 5.10 KernelPaul Spooren2022-01-191-1/+1
| | | | | | | Tested by multiple users and since all targets need to be on Kernel 5.10 to be part of the next release, add changes. Signed-off-by: Paul Spooren <mail@aparcar.org>
* mvebu: cortexa9: Fix board.d/01_ledsKlaus Kudielka2022-01-181-1/+1
| | | | | | | Fix syntax error in the case statement Fixes: 9149ed4f05f8 ("mvebu: cortexa9: Add support for Ctera C200-V2") Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
* ipq40xx: rename RT-AC42U WLAN/LAN LEDsSungbo Eo2022-01-172-8/+10
| | | | | | | | | | Assign LED numbers properly by adding function-enumerator property in DTS. While at it, remove default trigger of LAN LEDs as it will be handled in 01_leds anyway. Fixes: 51b9aef553a8 ("ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: image: remove unused DTB_SIZE variableSungbo Eo2022-01-171-2/+0
| | | | | | It is not included in DEVICE_VARS anyways. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* treewide: drop use of whichAnsuel Smith2022-01-171-1/+1
| | | | | | | | | | | | | | Ubuntu started to flag which as deprecated and it seems which is not really standard and may vary across Distro. Drop the use of which and use the standard 'command -v' for this simple task. Which is still present in the prereq if some package/script still use which. A utility script called command_all.sh is implemented that will just mimic the output of which -a. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* omap: add support for the TRNG Hardware AcceleratorAlexey Smirnov2022-01-161-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to TI docs (Processor SDK Linux Getting Started Guide) the Random Number Generator hardware is found on OMAP16xx, OMAP2/3/4/5, AM33xx/AM43xx boards. It already defined in device tree files. Let's enable it. Some tests: root@RTS1_OI:~# rngtest -c 1000 </dev/hwrng rngtest 6.10 Copyright (c) 2004 by Henrique de Moraes Holschuh This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. rngtest: starting FIPS tests... rngtest: bits received from input: 20000032 rngtest: FIPS 140-2 successes: 999 rngtest: FIPS 140-2 failures: 1 rngtest: FIPS 140-2(2001-10-10) Monobit: 0 rngtest: FIPS 140-2(2001-10-10) Poker: 0 rngtest: FIPS 140-2(2001-10-10) Runs: 1 rngtest: FIPS 140-2(2001-10-10) Long run: 0 rngtest: FIPS 140-2(2001-10-10) Continuous run: 0 rngtest: input channel speed: (min=198.710; avg=1265.501; max=2976.417)Kibits/s rngtest: FIPS tests speed: (min=1.780; avg=37.085; max=39.736)Mibits/s rngtest: Program run time: 15961329 microseconds Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
* ltq-deu: add ltq-deu back to default packagesDaniel Kestrel2022-01-163-7/+9
| | | | | | | | | After enhancing ltq-deu, build it by default for the devices using it. Reverts: 964863b ("ltq-deu: Mark lantiq DEU broken") Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
* ath79: use lzma-loader for ZyXEL NBG6716Lech Perczak2022-01-161-3/+3
| | | | | | | | | | | | | | | | | Since gzip-compressed kernel image stopped fitting on 4MB kernel partition on the device, use lzma-loader wrapping LZMA-compressed kernel. This yields bootable device once again, and saves a very substantial amount of space, the kernel size decreasing from about 4.4MB to about 2.5MB for 5.10 kernel. This avoids changing of the flash layout for the device. While at that, reactivate the build for the device. Fixes: 5d8ea6d34f9 ("ath79: Deactivate ZyXEL NBG6716 by default") Cc: André Valentin <avalentin@marcant.net> Cc: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Alex Henrie <alexhenrie24@gmail.com> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ath79: Add support for OpenMesh OM2P v1Sven Eckelmann2022-01-166-0/+189
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros AR7240 rev 2 * 350/350/175 MHz (CPU/DDR/AHB) * 32 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + 18-24V passive POE (mode B) + used as WAN interface - eth1 + builtin switch port 4 + used as LAN interface * 12-24V 1A DC * external antenna The device itself requires the mtdparts from the uboot arguments to properly boot the flashed image and to support dual-boot (primary + recovery image). Unfortunately, the name of the mtd device in mtdparts is still using the legacy name "ar7240-nor0" which must be supplied using the Linux-specfic DT parameter linux,mtd-name to overwrite the generic name "spi0.0". Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Allow to set spi-nor mtd name via devicetreeSven Eckelmann2022-01-161-0/+54
| | | | | | | | | | | | | | | On ar71xx, it was possible to overwrite the name of the spi-nor mtd device identifier using the flash_platform_data which each mach-*.c could adjust for its devices. A similar feature was introduced for mtd-physmap in devicetree's. The property linux,mtd-name can be used to set the name and provide a stable identifier for mtdpart from the bootloader. But this feature is not yet available upstream for spi-nor devices which also might receive their partition layout from the bootloader. But the OpenWrt pistachio support for this property can simply be imported into ath79 to gain this support. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh OM5P-AC v2Sven Eckelmann2022-01-164-33/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/200 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 4x GPIO-LEDs (3x wifi, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8031 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas This device support is based on the partially working stub from commit 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon"). Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* lantiq: backport latest upstream patchesAleksander Jan Bajkowski2022-01-163-0/+266
| | | | | | | | | | | | This patch includes a series of performance improvements. All patches were accepted and should land in 5.17. NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500): Down Up Before 539 Mbps 599 Mbps After 624 Mbps 695 Mbps Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* lantiq: xrx200: enable use of baby jumbo framesThomas Nixon2022-01-166-12/+484
| | | | | | | | | | | | | | | | | | xrx200 max MTU is reduced so that it works correctly when set to the max, and the max MTU of the switch is increased to match. In 5.10, the switch driver now enables non-standard MTUs on a per-port basis, with the overall frame size set based on the cpu port. When the MTU is not used, this should have no effect. The maximum packet size is limited as large packets cause the switch to lock up. 0702-net-lantiq-add-support-for-jumbo-frames.patch comes from net-next commit 998ac358019e491217e752bc6dcbb3afb2a6fa3e. In 5.4, all switch ports are configured to accept the max MTU, as 5.4 does not have port_max_mtu/port_change_mtu callbacks. Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* kernel: bump 5.10 to 5.10.92Rui Salvaterra2022-01-1652-413/+183
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.91Rui Salvaterra2022-01-163-9/+9
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.4 to 5.4.172John Audia2022-01-161-1/+1
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/mt7621 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.4 to 5.4.171John Audia2022-01-161-7/+7
| | | | | | All patches automatically rebased. Signed-off-by: John Audia <graysky@archlinux.us>
* ipq40xx: AP-365: fix non-existent node or label "macaddr_mfginfo_1d"Christian Lamparter2022-01-161-0/+7
| | | | | | | | | | | | | | | | | | | Chen Minqiang reported on github: | DTC arch/arm/boot/dts/qcom-ipq4029-ap-365.dtb |qcom-ipq4019.dtsi:520.23-560.5: ERROR (phandle_references): /soc/wifi@a000000: |Reference to non-existent node or label "macaddr_mfginfo_1d" | | also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:243.8-248.3 |qcom-ipq4019.dtsi:562.23-602.5: ERROR (phandle_references): /soc/wifi@a800000: |Reference to non-existent node or label "macaddr_mfginfo_1d" | | also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:250.8-256.3 |ERROR: Input tree has errors, aborting (use -f to force output) |scripts/Makefile.lib:326: recipe for target 'qcom-ipq4029-ap-365.dtb' failed Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") Reported-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* lantiq: increase fritz-cal-extract output limitDavid Bauer2022-01-151-2/+2
| | | | | | | | | | | It was reported the caldata on the FritzBox 7430 is not only stored at different offsets, but is also larger than the current output size limit. Increase the output file size limit (after deflate) by 1024 bytes. Ref: FS#3604 ("ath9k firmware is 0 bytes on Fritzbox 7430") Signed-off-by: David Bauer <mail@david-bauer.net>
* build: move Build/copy-file to image-commands.mkChristian Lamparter2022-01-152-8/+0
| | | | | | This is makro is present in more than one place. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: patch Asus RP-AC66 clean up and fix for sysupgrade imageTamas Balogh2022-01-154-8/+6
| | | | | | | | - clean up leftovers regarding MAC configure in dts - fix alphabetical order in caldata - IMAGE_SIZE for sysupgrade image Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* mvebu: Move cortexa9 specific config options from global configMarek Behún2022-01-152-2/+4
| | | | | | | | | | | Move config options CONFIG_PHY_MVEBU_A38X_COMPHY CONFIG_RTC_DRV_MV to cortexa9/config-5.10. These are not needed for arm64 targets. Signed-off-by: Marek Behún <kabel@kernel.org>
* mvebu: cortexa9: Add support for Ctera C200-V2Pawel Dembicki2022-01-157-1/+527
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 2-Bay NAS - maximum two 3.5" Harddisks Hardware: - SoC: Marvell 88F6707-A1 ARMv7 Processor 1,2GHz (ARMADA 370 SoC) - Ram: 1GB (2x Nanya NT5CC512M8DN-D1) - NAND Flash: 256MB (ESMT F59L2G81A-25T) - Lan: 1x GBE (Marvell 88E1318-NNB2) - Storage: 2x SATA HDD 3.5" Slot - USB: 2x USB 3.0 port (Renesas uPD720202) - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND) - LEDs: 13x GPIO controlled - Buttons: 2x GPIO controlled Known issues: - Buzzer is unused due lack of proper driver - USB1/2 usbport ledtrigger won't work (through DT) - Renesas uPD720202 requires firmware file. It's possible to find non-free binary. Please look for 'UPDATE.mem' file and put in into '/lib/firmware/renesas_usb_fw.mem' file. Installation: - Apply factory initramfs image via stock web-gui. - Do sysupgrade to make installation complete. Back to stock: - OpenWrt rootfs partition use unused space after stock firmware. - Full revert is possible. - Login via ssh and run: ## ctera_c200-v2_back_to_factory start ## . /lib/functions.sh part=$(find_mtd_part "active_bank") active_bank=$(strings "$part" | grep bank) if [ "$active_bank" = "bank1" ]; then echo "bank2" > /tmp/change_bank else echo "bank1" > /tmp/change_bank fi mtd write /tmp/change_bank active_bank reboot ## ctera_c200-v2_back_to_factory end ## Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (put back-to-stock script into commit message, removed dup. SUBPAGESIZE var, added 01_leds for non-working dt-usb-port trigger) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mvebu: enable watchdog for Armada 37XXJosef Schlehofer2022-01-151-0/+1
| | | | | | | | | | | | | | This option includes support for watchdog timer on Marvell Armada 37xx SoCs. [1] It is useful e.g. for Turris MOX, Marvell ESPRESSObin Enable armada-37xx-watchdog driver as built in for mvebu cortex-a53, so that kernel can start serving as soon as the driver is probed, until userspace takes over it. [1] https://cateee.net/lkddb/web-lkddb/ARMADA_37XX_WATCHDOG.html Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (improved commit message, 2nd paragraph) Signed-off-by: Marek Behún <kabel@kernel.org>
* mvebu: cortexa53: Enable Armada 37xx rWTM driverMarek Behún2022-01-151-0/+4
| | | | | | | | | | | | | | | | | Enabling Armada 37xx rWTM driver. This gives the kernel access to random number generator, if provided by the rWTM firmware. Note that the driver is called turris-mox-rwtm because it was initially written for Turris MOX, but will also work on other Armada 37xx platforms, if they use rWTM firmware from CZ.NIC [1]. It makes sense to have this driver built-in, so that kernel has access to random number generator without needing to load any drivers. [1] https://gitlab.nic.cz/turris/mox-boot-builder Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Andre Heider <a.heider@gmail.com>
* kernel: 5.10: Backport pending Armada 3720 comphy patchesMarek Behún2022-01-156-0/+2114
| | | | | | | | | | | | | | Backport 5 pending patches [1] for Armada 3720 comphy driver and one patch for device tree, applied to mvebu-dt64, but pending to appear in Linus' tree [2]. These patches makes the driver work correctly even with older, buggy versions of TF-A firmware. [1] http://lists.infradead.org/pipermail/linux-phy/2022-January/002598.html [2] http://lists.infradead.org/pipermail/linux-phy/2021-December/002279.html Signed-off-by: Marek Behún <kabel@kernel.org>
* kernel: 5.10: Backport Armada 3720 comphy patches from 5.15Marek Behún2022-01-152-0/+117
| | | | | | | | | Backport 2 patches for Armada 3720 comphy from 5.15 kernel. These are needed for clear application of pending patches that fix this driver. Signed-off-by: Marek Behún <kabel@kernel.org>
* kernel: 5.10: Backport pending pci-aardvark changes fixing MSI supportMarek Behún2022-01-1523-0/+1725
| | | | | | | | | | | | | Backport Aardvark PCIe controller driver changes that fix MSI support, that were recently sent to the linux-pci mailing list [1]. These changes fix MSI and MSI-X support for this PCIe controller, which, among other things, make it possible to use NVMe drives with this PCIe controllers. [1] https://lore.kernel.org/linux-pci/20220110015018.26359-1-kabel@kernel.org/ Signed-off-by: Marek Behún <kabel@kernel.org>
* kernel: 5.10: Backport pci-aardvark driver changes from 5.17Marek Behún2022-01-1511-0/+545
| | | | | | | | | | | | | | Backport Aardvark PCIe controller driver changes that will appear in 5.17 kernel. They are currently accessible on LKML [1], in linux-next repository [2], or in Bjorn Helgaas' repository [3]. These changes mainly enhance driver removal method. [1] https://lore.kernel.org/linux-pci/20211130172913.9727-1-kabel@kernel.org/ [2] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/log/drivers/pci?h=next-20220107 [3] https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/log/?h=next Signed-off-by: Marek Behún <kabel@kernel.org>
* mvebu: kernel: enable CONFIG_BLK_DEV_NVMEJosef Schlehofer2022-01-151-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_BLK_DEV_NVME [1]: - This is a kernel driver for SSD connected to PCI or PCIe bus [1]. By default, it is enabled for targets "ipq807x", "rockchip/armv8" and "x86/64". With miniPCIe adapter, there is a possibility to connect NVMe disk to Turris Omnia (cortex-a9), Turris MOX (cortex-a53). It allows to boot system from NVMe disk, because of that it can not be kmod package as you can not access the disk to be able to boot from it. CONFIG_NVME_CORE [2]: - This is selected by CONFIG_BLK_DEV_NVME It does not need to be explicitly enabled, but it is done for "ipq807", "x64_64" and rockchip/armv8", which has also enabled the previous config option as well. Kernel increase: ~28k KiB on mamba kernel Reference: [1] https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html [2] https://cateee.net/lkddb/web-lkddb/NVME_CORE.html Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* ipq40xx: utilize nvmem-cells for macs & (pre-)calibration dataChristian Lamparter2022-01-1531-131/+487
| | | | | | | | | | | | | | | moves extraction entries out of 11-ath10k-caldata and into the individual board's device-tree. Some notes: - mmc could work as well (not tested) - devices that pass the partitions via mtdparts bootargs are kept as is - gl-b2200 has a weird pcie wifi device (vendor claims 9886 wave 2. But firmware-extraction was for a wave 1 device?!) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add RT-ACRH13 alternative name to RT-AC58UChristian Lamparter2022-01-151-0/+2
| | | | | | RT-ACRH13 is another name this device was sold as (US?). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS RT-ACRH17/RT-AC42UJoshua Roys2022-01-1511-22/+363
| | | | | | | | | | | | | | | | | | | | | SOC: IPQ4019 CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d DRAM: 256 MB NAND: 128 MiB Macronix MX30LF1G18AC ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN) USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4 INPUT: 1x WPS, 1x Reset LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed with an intermediary initramfs image, the jffs2 ubi volume deleted, and then finally a sysupgrade with the final image performed. Signed-off-by: Joshua Roys <roysjosh@gmail.com> (added ALT0) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: fix reboot for remaining 32 MB boardsMichael Pratt2022-01-1522-7/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following devices have a Winbond W25Q256FV flash chip, which does not have the RESET pin enabled by default, and otherwise would require setting a bit in a status register. Before moving to Linux 5.4, we had the patch: 0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch which kept specific flash chips with explicit 3-byte and 4-byte address modes to stay in 3-byte address mode while idle (after an erase or write) by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch. this was obsoleted by the patch: 481-mtd-spi-nor-rework-broken-flash-reset-support.patch which uses the newer upstream flag SNOR_F_BROKEN_RESET for devices with a flash chip that cannot be hardware reset with RESET pin and therefore must be left in 3-byte address mode when idle. The new patch requires that the DTS of affected devices have the property "broken-flash-reset", which was not yet added for most of them. This commit adds the property for remaining affected devices in ramips target, specifically because of the flash chip model. However, it is possible that there are other devices where the flash chip uses an explicit 4-byte address mode and the RESET pin is not connected to the SOC on the board, and those DTS would also need this property. Ref: 22d982ea0033 ("ramips: add support for switching between 3-byte and 4-byte addressing") Ref: dfa521f12953 ("generic: spi-nor: rework broken-flash-reset") Signed-off-by: Michael Pratt <mcpratt@pm.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-26 16:17:19 +0000