aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* realtek: Add port to smi-bus address mappingBirger Koblitz2021-10-091-32/+69
| | | | | | | | All RTL SoCs addresss PHYs via their port number, which is mapped to an SMI address. Add support for configuring this mapping via the .dts on all SoCs apart from the 839x, where the mapping to the 64 ports is fixed. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Increase maximum RX ring buffer lengthBirger Koblitz2021-10-091-4/+5
| | | | | | | Increase the maximum ring buffer length in order to improve performance on RTL839x devices. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Improve TX CPU-Tag usageBirger Koblitz2021-10-091-20/+29
| | | | | | | | | On RTL83xx enable learning of the MAC source address of the CPU port from outgoing packets. Add documentation on bit fields. On RTL93xx enable port-mask usage and the use of internal priority, these SoCs automatically learn the MAC. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Remove storm control and attack warningsBirger Koblitz2021-10-091-25/+0
| | | | | | | | Remove the storm control and attack warnings from the IRQ handler of the Ethernet driver. There was no consequence to the detection and the kernel can also handle at least the attacks itself. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* realtek: Correct TX ring size in ethernet driverBirger Koblitz2021-10-091-2/+1
| | | | | | | This enlarges the size of the TX ring buffer, which prevents warnings when the buffer runs out of space. Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
* config: pack toolchain per default on buildbotsPaul Spooren2021-10-081-0/+1
| | | | | | | The toolchain can be used for accelerated CI builds. This commit enabled the packing of it by default on buildbots. Signed-off-by: Paul Spooren <mail@aparcar.org>
* kernel: export switch_generic_set_link() symbolRafał Miłecki2021-10-071-0/+1
| | | | | | | | | | | | This fixes: ERROR: "switch_generic_set_link" [drivers/net/phy/b53/b53_common.ko] undefined! At some point all packages for swconfig drivers were dropped and targets were meant to have them built into kernels. It seems b53 (re-)gained its kmod-switch-bcm53xx however and b53 needs to be built as module. Fixes: b2cfed48f626 ("Revert "swconfig: fix Broadcom b53 support"") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: 5.10: dsa: don't set skb->offload_fwd_mark when not offloading bridgeMatthew Hagan2021-10-071-0/+138
| | | | | | | | | | | Add Vladimir Oltean's "net: dsa: don't set skb->offload_fwd_mark when not offloading the bridge" This covers cases where packets received by an upstream switch must be forwarded back on the same port, which skb->offload_fwd_mark normally prevents. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* Revert "swconfig: fix Broadcom b53 support"Rafał Miłecki2021-10-072-33/+0
| | | | | | | | | | | | | | | | | | | | This reverts commit 8f9cd1af0f9c325a902dbd0e79e12015372e6bb0. That commit was meant to add a single EXPORT_SYMBOL_GPL() but it actually also added few .of_match_table-s. One commit should handle one thing and should not introduce unrelated changes. Regarding actual changes: 1. EXPORT_SYMBOL_GPL is not required as we don't build swconfig drivers as modules. 2. PHY drivers must not have .of_match_table. That is allowed for MDIO drivers. This could work for some time (although is didn't for me on bcm53xx) but does not with kernel 5.10. It causes a soft lockup and upstream developers confirmed it's an unsupported design. Link: https://lore.kernel.org/netdev/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com/t/#mf80e472f35ee23f7a75cbf5b1e101a17ab3a64a3 Cc: Tobias Schramm <tobleminer@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport bgmac upstream commits from 5.15 / for 5.16Rafał Miłecki2021-10-075-2/+177
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mpc85xx: switch to Kernel 5.10Adrian Schmutzler2021-10-052-2/+2
| | | | | | | | This has testing support for 7 months. Time to switch. TL-WDR4900 is disabled due to kernel size limitation. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: 5.10: add missing symbolsPawel Dembicki2021-10-054-5/+4
| | | | | | | | | | | | Three missing symbols were found during mpc85xx/p2020 compilation. While at it, CONFIG_FSL_ENETC_MDIO is moved to generic config for consistency. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [move CONFIG_FSL_ENETC_MDIO, remove redundant definitions, adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm27xx: remove obsolete kernel 5.4Adrian Schmutzler2021-10-051051-266922/+0
| | | | | | | With the upgrade to kernel 5.10 per default the old version is no longer required to be in tree. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm27xx: add RPI_AXIPERF symbolStijn Tintel2021-10-058-0/+8
| | | | | | | | When KERNEL_PERF_EVENTS is enabled in OpenWrt, or PERF_EVENTS in the kernel config, the RPI_AXIPERF is exposed. Add it to the subtarget kernel configs to avoid build failures. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* bcm27xx: add SND_SOC_AD193X_{I2C,SPI} symbolsStijn Tintel2021-10-059-2/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When building an image for the bcm27xx target, some combinations of config options will fail to build due the SND_SOC_AD193X_I2C and SND_SOC_AD193X_SPI kernel config symbols being missing. The problem only occurs on bcm27xx as the target contains a patch that modifies the Kconfig file containing the symbols; in the vanilla kernel, there is no string after the tristate keyword so the symbol is not exposed. The _I2C symbol depends on I2C, which is enabled in the kernel configs of all bcm27xx subtargets. The _SPI symbol depends on SPI_MASTER, which is exposed by either kmod-mmc-spi, kmod-spi-bitbang, kmod-spi-dev, kmod-spi-bcm2835 or kmod-spi-bcm2835-aux. Both symbols are defined in the sound/soc/codecs directory, which is only included when SND_SOC is enabled, so this problem doesn't occur when kmod-sound-soc-core is not enabled. As the kmod-sound-soc-bcm2835-i2s package disables the SND_SOC_AD193X_SPI symbol, it also doesn't occur when kmod-sound-soc-bcm2835-i2s is enabled. As there are several possible config combinations that do exhibit this problem, it is best to solve it by adding the missing symbols to the subtarget kernel configs. By doing this we can remove them from the kmod-sound-soc-bcm2835-i2s package. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: fix USW-Flex reversed switch-port orderDavid Bauer2021-10-041-4/+4
| | | | | | | Switch port order was reversed due to reading the internal labling (which mismatches the one on the case). Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: Deactivate some ARM64 errata workaroundsHauke Mehrtens2021-10-0317-61/+10
| | | | | | | | | | | This deactivates the following workarounds for erratas in ARM64 CPUS: CONFIG_ARM64_ERRATUM_1165522: Cortex-A76 cores (r0p0, r1p0, r2p0) CONFIG_ARM64_ERRATUM_1286807: Cortex-A76 cores (r0p0 to r3p0) CONFIG_ARM64_ERRATUM_1418040: Cortex-A76/Neoverse-N1 cores (r0p0 to r3p1) CONFIG_CAVIUM_TX2_ERRATUM_219: Cavium ThunderX2 CONFIG_FUJITSU_ERRATUM_010001: Fujitsu-A64FX Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: Refresh kernel 5.10 configurationHauke Mehrtens2021-10-033-115/+18
| | | | | | | | The cortex53 subtarget was missing multiple config options and the other targets just defined some options which are not needed. Fixes: 83672f506d95 ("sunxi: add testing Linux 5.10") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: Activate CONFIG_SATA_PMPHauke Mehrtens2021-10-031-0/+2
| | | | | | | | The kernel 5.4 configuration activated SATA Port Multiplier support, add it to kernel 5.10 too. Fixes: 83672f506d95 ("sunxi: add testing Linux 5.10") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kirkwood: refresh kernel configSungbo Eo2021-10-031-3/+7
| | | | | | | Refresh config with make kernel_oldconfig. Tested-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: solidify SATA_PMP configSungbo Eo2021-10-032-0/+24
| | | | | | | | | | | | | | | | | | | SATA_PMP option is no longer exposed when no SATA host driver is enabled since upstream linux commit bd322af15ce9 ("ata: make SATA_PMP option selectable only if any SATA host driver is enabled"). Commit 1bb3f593ee73 ("kirkwood: update config for kernel 5.10") manually added CONFIG_SATA_PMP=y to config file, but the config will disappear for every kernel_oldconfig refresh. To prevent this, a small hack is added, which selects SATA_HOST automatically when SATA_PMP is enabled. This patch can be dropped if SATA_MV is ever re-added into kernel config file. Tested-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Sungbo Eo <mans0n@gorani.run> [Move patch to generic/hack-5.10] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: add recipe for common setup with loader-okli-compileAdrian Schmutzler2021-10-023-25/+13
| | | | | | | These instructions are repeated for a few devices now, let's move them to shared definition so we do not repeat ourselves too often. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* realtek: ensure output drivers are enabled in RTL8231Paul Fertser2021-10-022-10/+14
| | | | | | | | | | | | | The bootloader can leave the GPIO expander in a state which doesn't have output drivers enabled so GPIOs will properly work for input but output operations will have no effect. To avoid disrupting the boot in case the bootloader left direction and data registers in an inconsistent state (e.g. pulling SoC's reset to 0) reconfigure everything as input. Reviewed-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Paul Fertser <fercerpav@gmail.com>
* mvebu: remove obsolete Kernel 5.4Paul Spooren2021-10-0273-8546/+0
| | | | | | | With the upgrade to Kernel 5.10 per default the old version is no longer required to be in tree. Signed-off-by: Paul Spooren <mail@aparcar.org>
* ipq806x: remove obsolete Kernel 5.4Paul Spooren2021-10-0246-8294/+0
| | | | | | | With the upgrade to Kernel 5.10 per default the old version is no longer required to be in tree. Signed-off-by: Paul Spooren <mail@aparcar.org>
* gemini: remove obsolete Kernel 5.4Paul Spooren2021-10-025-847/+0
| | | | | | | With the upgrade to Kernel 5.10 per default the old version is no longer required to be in tree. Signed-off-by: Paul Spooren <mail@aparcar.org>
* malta: remove obsolete Kernel 5.4Paul Spooren2021-10-021-335/+0
| | | | | | | With the upgrade to Kernel 5.10 per default the old version is no longer required to be in tree. Signed-off-by: Paul Spooren <mail@aparcar.org>
* armvirt: remove obsolete Kernel 5.4Paul Spooren2021-10-023-385/+0
| | | | | | | With the upgrade to Kernel 5.10 per default the old version is no longer required to be in tree. Signed-off-by: Paul Spooren <mail@aparcar.org>
* x86: remove obsolete Kernel 5.4Paul Spooren2021-10-0210-2009/+0
| | | | | | | With the upgrade to Kernel 5.10 per default the old version is no longer required to be in tree. Signed-off-by: Paul Spooren <mail@aparcar.org>
* kernel: bump 5.4 to 5.4.150Hauke Mehrtens2021-10-0255-152/+118
| | | | | | | | | | | | | | | | Manually rebased: generic/pending-5.4/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch mvebu/patches-5.4/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch Removed upstreamed: layerscape/patches-5.4/819-uart-0004-MLK-18137-fsl_lpuart-Fix-loopback-mode.patch All others updated automatically. Compile-tested on: lantiq/xrx200, armvirt/64 Runtime-tested on: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: add Globalscale MOCHAbinRobert Marko2021-10-025-0/+469
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Globalscale MOCHAbin is a Armada 7040 based development board. Specifications: * Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz * 2 / 4 / 8 GB of DDR4 DRAM * 16 GB eMMC * 4MB SPI-NOR (Bootloader) * 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only) * 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only) * 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C) * 1x SATA 7+15 socket (SATA3) * 1x 16-pin (2×8) MikroBus Connector * 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots) * 2x USB3.0 Type-A ports via SMSC USB5434B hub * Cortex 2x5 JTAG * microUSB port for UART (PL2303GL/PL2303SA onboard) * 1x 10G SFP+ * 1x 1G SFP (Connected to 88E1512 PHY) * 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY) * 4x 1G RJ45 ports via Topaz 88E6141 switch * RTC with battery holder (SoC provided, requires CR2032 battery) * 1x 12V DC IN * 1x Power switch * 1x 12V fan header (3-pin, power only) * 1x mini-PCIe LED header (2x0.1" pins) * 1x M.2-2280 LED header (2x0.1" pins) * 6x Bootstrap jumpers * 1x Power LED (Green) * 3x Tri-color RGB LEDs (Controllable) * 1x Microchip ATECC608B secure element Note that 1G SFP and 1G WAN cannot be used at the same time as they are in parallel connected to the same PHY. Installation: Copy dtb from build_dir to bin/ and run tftpserver there: $ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/ $ in.tftpd -L -s bin/targets/mvebu/cortexa72/ Connect to the device UART via microUSB port and power on the device. Power on the device and hit any key to stop the autoboot. Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g: $ setenv serverip 192.168.1.10 # Host $ setenv ipaddr 192.168.1.15 # Device Set the ethernet device (Example for the 1G WAN): $ setenv ethact mvpp2-2 Ping server to confirm network is working: $ ping $serverip Using mvpp2-2 device host 192.168.1.15 is alive Tftpboot the firmware: $ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin $ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb Boot the image: $ booti $kernel_addr_r - $fdt_addr_r Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz to /tmp dir on the device. Gunzip and dd the image: $ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz $ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync Reboot the device. Hit any key to stop the autoboot. Reset U-boot env and set the bootcmd: $ env default -a $ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}' Optionally I would advise to edit the console env variable to remove earlycon as that causes the kernel to never use the driver for the serial console. Earlycon should be used only for debugging before the kernel can configure the console and will otherwise cause various issues with the console. $ setenv console 'console=ttyS0,115200' Save and reset $ saveenv $ reset OpenWrt should boot from eMMC now. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* lantiq: kernel: xway-nand: Move ECC engine setting to new DT bindingDaniel Kestrel2021-10-0213-7/+50
| | | | | | | | | | | | | | | | When trying to add support for another device with Micron NAND chips, it was discovered that the default setting in the kernel source does not work with Micron Chips, since the device trees setting is overwritten and hard coded by the kernel xway_nand driver. This was the original reason for this PR. A kernel patch sets the default ECC mode to soft without overwriting the device tree settings and the device tree for devices using it are updated with new parameters because the old ones are deprecated by torvalds/linux@533af69. A patch for kernel 5.4 is provided to support the new settings because kernel 5.4 does not support it. Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
* lantiq: kernel: xway-nand: Fix setting on-die ECC engines in dtsHauke Mehrtens2021-10-022-2/+70
| | | | | | | This backports a fix proposed for upstream kernel to fix overwriting the NAND ECC engine in device tree. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: mt7623: bpi-r2: add LED aliasesDaniel Golle2021-10-011-0/+29
| | | | | | Add aliases for LEDs in device tree of the BPi-R2. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: remove files and patches for Linux 5.4Daniel Golle2021-10-01183-111722/+0
| | | | | | | All subtargets only provide files and patches for Linux 5.10 by now so there is little use for the old Linux 5.4 stuff. Remove it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* armvirt: switch to Kernel 5.10Paul Spooren2021-10-011-2/+1
| | | | | | | | | | | | Armvirt is a development and testing platform and should therefore use the latest OpenWrt Kernel by default. Tested via qemu. Acked-by: Rosen Penev <rosenp@gmail.com> Acked-by: Yousong Zhou <yszhou4tech@gmail.com> Signed-off-by: Paul Spooren <mail@aparcar.org>
* malta: switch to Kernel 5.10Paul Spooren2021-10-011-2/+1
| | | | | | | | | | Malta is a development and testing platform and should therefore use the latest OpenWrt Kernel by default. Acked-by: Rosen Penev <rosenp@gmail.com> Acked-by: Yousong Zhou <yszhou4tech@gmail.com> Signed-off-by: Paul Spooren <mail@aparcar.org>
* mediatek: add FEATURES and order them alphabeticallyDaniel Golle2021-09-302-2/+2
| | | | | | | | Add common features 'gpio', 'nand', 'pci', 'pcie', 'squashfs' and 'usb' for all mediatek targets, add 'display' and 'usbgadget' for MT7623. Sort features alphabetically while at it. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: provide power on mPCIe in SATA modeDaniel Golle2021-09-301-17/+2
| | | | | | | | | User reported that R64 doesn't provide power to the mPCIe slot in case the PCIe port is disabled as it is when selecting the SATA configuration. As users may still want to use USB-connected mPCIe modules in CN8 slot. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.10 to 5.10.70Rui Salvaterra2021-09-307-52/+11
| | | | | | | Deleted (upstreamed): bcm53xx/patches-5.10/181-Revert-USB-bcma-Add-a-check-for-devm_gpiod_get.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.69Rui Salvaterra2021-09-304-24/+1
| | | | | | Patches automatically refreshed. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.68Rui Salvaterra2021-09-3021-534/+25
| | | | | | | | | | | | | Deleted (upstreamed): generic/backport-5.10/610-v5.13-02-netfilter-Fix-fall-through-warnings-for-Clang.patch generic/backport-5.10/792-v5.15-0001-net-dsa-b53-Fix-calculating-number-of-switch-ports.patch generic/backport-5.10/792-v5.15-0002-net-dsa-b53-Set-correct-number-of-ports-in-the-DSA-s.patch generic/backport-5.10/792-v5.15-0003-net-dsa-b53-Fix-IMP-port-setup-on-BCM5301x.patch generic/backport-5.10/840-0001-PCI-of-Don-t-fail-devm_pci_alloc_host_bridge-on-miss.patch generic/backport-5.10/840-0002-PCI-iproc-Fix-BCMA-probe-resource-handling.patch generic/pending-5.10/498-mtd-mtdconcat-select-readwrite-function.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.67Rui Salvaterra2021-09-3017-69/+27
| | | | | | | Deleted (upstreamed): bcm27xx/patches-5.10/950-0312-vc4_hdmi-Set-HD_CTL_WHOLSMP-and-HD_CTL_CHALIGN_SET.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.65Rui Salvaterra2021-09-3020-64/+72
| | | | | | | | | Manually refreshed: generic/pending-5.10/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch bcm27xx/patches-5.10/950-0053-firmware-bcm2835-Support-ARCH_BCM270x.patch bcm27xx/patches-5.10/950-0087-firmware-raspberrypi-Add-backward-compatible-get_thr.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ramips: add support for Netgear R7450Dale Hui2021-09-264-1/+30
| | | | | | | | | | | | | | | | | | | | | | | | | Netgear R7450 is a clone of Netgear R6700v2 Specifications ============== SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Flash Instructions ================== Login to netgear webinterface and flash factory.img Signed-off-by: Dale Hui <strokes-races0b@icloud.com> [fix model/compatible in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear R6900v2Dale Hui2021-09-264-0/+30
| | | | | | | | | | | | | | | | | | | | | | | Netgear R6900v2 is a clone of Netgear R6700v2 Specifications ============== SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Flash Instructions ================== Login to netgear webinterface and flash factory.img Signed-off-by: Dale Hui <strokes-races0b@icloud.com>
* ramips: add Nighthawk AC2100 as name for Netgear R6700v2Dale Hui2021-09-261-0/+3
| | | | | | | | Netgear Nighthawk AC2100 is another name of the Netgear R6700v2. Signed-off-by: Dale Hui <strokes-races0b@icloud.com> [adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: make Netgear R7200 a separate device from R6700v2Dale Hui2021-09-264-4/+30
| | | | | | | | | With the various variants of Netgear R**** devices, make it more obvious which image should be used for the R7200. Signed-off-by: Dale Hui <strokes-races0b@icloud.com> [provide proper commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* realtek: add Kernel 5.10 as testing versionINAGAKI Hiroshi2021-09-261-0/+1
| | | | | | | This patch adds "KERNEL_TESTING_PATCHVER:=5.10" to the Makefile in realtek target to allow using Kernel 5.10 for testing. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* realtek: enable uart1 on the devices with PoE support in 5.10INAGAKI Hiroshi2021-09-267-0/+28
| | | | | | | | | | | | | | | | On the devices with PoE support, the secondary UART (uart1) on the SoC is used to communicate between the SoC and controller. Enable the secondary UART on the following devices: - D-Link DGS-1210-10P - Netgear GS110TPP v1 - Netgear GS310TP v1 - ZyXEL GS1900-8HP v1/v2 - ZyXEL GS1900-10HP - ZyXEL GS1900-24HP v2 Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 13:20:51 +0000