aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Yuncore XD3200Thibaut VARÈNE2022-04-165-2/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry-picked from commit c91df224f54fdd44c9c0487a8c91876f5d273164)
* ramips: fix reboot for remaining 32 MB boardsMichael Pratt2022-04-0818-4/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following devices have a Winbond W25Q256FV flash chip, which does not have the RESET pin enabled by default, and otherwise would require setting a bit in a status register. Before moving to Linux 5.4, we had the patch: 0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch which kept specific flash chips with explicit 3-byte and 4-byte address modes to stay in 3-byte address mode while idle (after an erase or write) by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch. this was obsoleted by the patch: 481-mtd-spi-nor-rework-broken-flash-reset-support.patch which uses the newer upstream flag SNOR_F_BROKEN_RESET for devices with a flash chip that cannot be hardware reset with RESET pin and therefore must be left in 3-byte address mode when idle. The new patch requires that the DTS of affected devices have the property "broken-flash-reset", which was not yet added for most of them. This commit adds the property for remaining affected devices in ramips target, specifically because of the flash chip model. However, it is possible that there are other devices where the flash chip uses an explicit 4-byte address mode and the RESET pin is not connected to the SOC on the board, and those DTS would also need this property. Ref: 22d982ea0033 ("ramips: add support for switching between 3-byte and 4-byte addressing") Ref: dfa521f12953 ("generic: spi-nor: rework broken-flash-reset") Signed-off-by: Michael Pratt <mcpratt@pm.me> [pepe2k@gmail.com: backported to 21.02] Fixes: #9655, #9636, #9547 Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> (backported from commit 74516f4357d281f093f0daac01c4c5c239acc443)
* kernel: bump 5.4 to 5.4.188Hauke Mehrtens2022-04-0714-52/+47
| | | | | | | | | | | | | | Added the new configuration options: CONFIG_HARDEN_BRANCH_HISTORY=y CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY=y Manually adapted: target/linux/generic/hack-5.4/220-gc_sections.patch Compile-tested: lantiq/xrx200, armvirt/64 Run-tested: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* imagebuilder: fix broken image generation with external targetsPetr Štetiar2022-04-051-1/+1
| | | | | | | | | | | | When using external targets there is a symlink being created for the target under target/linux which then becomes dangling under Image Builder. Fix it by dereferencing the possible symlink. Tested on IB with external target, ipq40xx and mvebu. Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 621f39d1f438bf95dbae667c575926fa16a6d797) (cherry picked from commit ec9af870f3278f75549836b469baefa260e2ed41)
* ath79: migrate Archer C5 5GHz radio device pathsJan-Niklas Burfeind2022-03-311-0/+1
| | | | | | | | | | | | When upgrading a TP-Link Archer C5 v1 from ar71xx to ath79, the 5ghz radio stops working because the device path changed. Same has been done for the Archer C7 before: commit e19506f20618 ("ath79: migrate Archer C7 5GHz radio device paths") Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> (cherry picked from commit c6eb63d48f942f1e54737ed182776cf9a08de542)
* ath79: fix label MAC address for Ubiquiti UniFi AP Outdoor+Matthias Schiffer2022-03-303-2/+4
| | | | | | | | | | The label has the MAC address of eth0, not the WLAN PHY address. We can merge the definition back into ar7241_ubnt_unifi.dtsi, as both DTS derived from it use the same interface for their label MAC addresses after all. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit aee9ccf5c1b536189ebee8c232273657334da843)
* apm821xx: fix crash/panic related to SATA/SSD choiceChristian Lamparter2022-03-261-0/+65
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ticerex on the OpenWrt Forum reported a gnarly crash when he was using Samsung 840 and 850 EVOs with his MyBook Live: | BUG: Kernel NULL pointer dereference at 0x00000000 | Faulting instruction address: 0xc03ed4b8 | Oops: Kernel access of bad area, sig: 11 [#1] | BE PAGE_SIZE=4K PowerPC 44x Platform | CPU: 0 PID: 362 Comm: scsi_eh_1 Not tainted 5.4.163 #0 | NIP: c03ed4b8 LR: c03d27e8 CTR: c03ed36c | REGS: cfa59950 TRAP: 0300 Not tainted (5.4.163) | MSR: 00021000 <CE,ME> CR: 42000222 XER: 00000000 | DEAR: 00000000 ESR: 00000000 | GPR00: c03d27e8 cfa59a08 cfa55fe0 00000000 0fa46bc0 [...] | [..] | NIP [c03ed4b8] sata_dwc_qc_issue+0x14c/0x254 | LR [c03d27e8] ata_qc_issue+0x1c8/0x2dc | Call Trace: | [cfa59a08] [c003f4e0] __cancel_work_timer+0x124/0x194 (unreliable) | [cfa59a78] [c03d27e8] ata_qc_issue+0x1c8/0x2dc | [cfa59a98] [c03d2b3c] ata_exec_internal_sg+0x240/0x524 | [cfa59b08] [c03d2e98] ata_exec_internal+0x78/0xe0 | [cfa59b58] [c03d30fc] ata_read_log_page.part.38+0x1dc/0x204 | [cfa59bc8] [c03d324c] ata_identify_page_supported+0x68/0x130 | [...] This turned out this is an issue with upstream changing ATA_TAG_INTERNAL's value from 31 to 32 during 4.18 release. Update "SATA_DWC_QCMD_MAX" to account for that. Link: https://forum.openwrt.org/t/my-book-live-duo-reboot-loop/122464 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 5ac672cfab60e90ab8a0bf3491fa2a27619d22d6)
* mvebu: SFP backports for GPON modulesMarek Behún2022-03-2615-31/+262
| | | | | | | | | | | | | | | This backports the following upstream Linux patches net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant net: sfp: relax bitrate-derived mode check net: sfp: cope with SFPs that set both LOS normal and LOS inverted for 5.4 for mvebu platform. This fixes GPON modules: Ubiquiti U-Fiber Instant SFP GPON VSOL V2801F CarlitoxxPro CPGOS03-0490 v2.0 Signed-off-by: Marek Behún <marek.behun@nic.cz>
* ath79: fix link for long cables with OCEDO RaccoonDavid Bauer2022-03-261-1/+12
| | | | | | | | | | The OCEDO Raccoon had significant packet-loss with cables longer than 50 meter. Disabling EEE restores normal operation. Also change the ethernet config to reduce loss on sub-1G links. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 4551bfd91f31be5987727c77e58333fa06ba3acd)
* ath79: fix TPLINK_HWREV field for TL-WR1043ND v4Matthias Schiffer2022-03-251-0/+1
| | | | | | | | | | | Required to allow sysupgrades from OpenWrt 19.07. Closes #7071 Fixes: 98fbf2edc021 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader") Tested-by: J. Burfeind <git@aiyionpri.me> Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit 8ba71f1f6f2359f9cf54201e9fc037df33f123c0)
* sunxi: cortexa7: fix ethernet link detection on a20-olinuxino-lime2Petr Štetiar2022-03-241-0/+1
| | | | | | | | | | | | | | | | | | | | | | | a20-olinuxino-lime2 is currently having hard time with link detection of certain 1000Mbit partners due to usage of generic PHY driver, probably due to following missing workaround introduced in upstream in commit 3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"): The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric Pause capability is set. This issue is described in a Silicon Errata (DS80000691D or DS80000692D), which advises to always disable the capability. This patch implements the workaround by defining a KSZ9031 specific get_feature callback to force the Asymmetric Pause capability bit to be cleared. This fixes issues where the link would not come up at boot time, or when the Asym Pause bit was set later on. As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since revision H, so we need to use Micrel PHY driver on those devices. Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit ffa1088f63267f817a3adf34c84b8e8089b1a938)
* mvebu: udpu: include LM75 kmod by defaultRobert Marko2022-03-241-1/+1
| | | | | | | | | | uDPU has 2 LM75 compatible temperature sensors, so include the driver for them by default in order to utilize them. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase] (cherry picked from commit a8b2d3590329386d0ae6873460b2d5126f63ddaa) (cherry picked from commit b9e90935db8e0c0166c80fc6e5e50755282e9e0b)
* mvebu: udpu: fix initramfs bootingRobert Marko2022-03-241-1/+1
| | | | | | | | | | | | uDPU provides a FIT based initramfs, but currently gets stuck after U-boot starts the kernel at "Starting kernel..". It is due to the load address being too low, so increase it in order to get the initramfs booting again. Signed-off-by: Robert Marko <robert.marko@sartura.hr> (cherry picked from commit 80f21e53360d52d493c51a4a263d9b7607b7494e) (cherry picked from commit d65269a732d82ca9d084c89d6ca05d125d4ab629)
* ath79: fix label MAC address for Ubiquiti UniFiMatthias Schiffer2022-03-243-4/+2
| | | | | | | The label has the MAC address of eth0, not the WLAN PHY address. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit 2a02b7049966dc77ae9519ca165f29b75e0dbf0e)
* ramips: remove kmod-mt7663-firmware-sta from device packagesFelix Fietkau2022-03-231-2/+2
| | | | | | | | | This firmware should only be used for mobile devices (e.g. laptops), where AP mode functionality is typically not used. This firmware supports a lot of power saving offload functionality at the expense of AP mode support. Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry picked from commit a1ac8728f80314c574201013e7fea58536c2b3ee)
* kernel: backport DSA patches fixing null-pointer dereferenceMarek Behún2022-03-212-0/+143
| | | | | | | | | | | | [ backport of master commit fbe2c3feaa4ef5747a691cb4c808925b024ff450 ] Backport patches 381a730182f1 ("net: dsa: Move VLAN filtering syncing out of dsa_switch_bridge_leave") 108dc8741c20 ("net: dsa: Avoid cross-chip syncing of VLAN filtering") from upstream (currently in net-next) to fix null-pointer dereference. Signed-off-by: Marek Behún <marek.behun@nic.cz> Signed-off-by: Petr Štetiar <ynezz@true.cz> [master commit detail]
* bcm4908: include U-Boot in imagesRafał Miłecki2022-03-141-3/+32
| | | | | | | This is a step forward in adding support for devices with U-Boot. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 34fd5e325af5cbcb64696c9b4b1660f22299790f)
* x86: legacy: enable pata_sis driverMatthias Schiffer2022-03-101-0/+1
| | | | | | | | | This driver is needed to boot from CompactFlash on the Siemens Futro S400. The device has an AMD NX1500 CPU, which seems to be unsupported by the geode subtarget, so it must use legacy. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit c8350dfb3cdee7653744bbb4ee3b0ac1b015912c)
* bcm4908: support "rootfs_data" on U-Boot devicesRafał Miłecki2022-03-073-13/+122
| | | | | | | | | | | | | | | | | | | | | | | | | | 1. Create "rootfs_data" dynamicaly U-Boot firmware images can contain only 2 UBI volumes: bootfs (container with U-Boot + kernel + DTBs) and rootfs (e.g. squashfs). There is no way to include "rootfs_data" UBI volume or make firmware file tell U-Boot to create one. For that reason "rootfs_data" needs to be created dynamically. Use preinit script to handle that. Fire it right before "mount_root" one. 2. Relate "rootfs_data" to flashed firmware As already explained flashing new firmware with U-Boot will do nothing to the "rootfs_data". It could result in new firmware reusing old "rootfs_data" overlay UBI volume and its file. Users expect a clean state after flashing firmware (even if flashing the same one). Solve that by reading flash counter of running firmware and storing it in "rootfs_data" UBI volume. Every mismatch will result in wiping old data. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 93259e8ca261c7965618fe11c2d385638da5cfa6)
* bcm4908: fix USB PHY supportRafał Miłecki2022-03-071-0/+147
| | | | | | | This fixes problem with USB PHY not handling some USB 3.0 devices. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 0dbcefdd5229daacf6cd4c9996b8e6f31c90ffd1)
* kernel: bump 5.4 to 5.4.182Hauke Mehrtens2022-03-0620-64/+35
| | | | | | | | | | | | | | The following patch was integrated upstream: target/linux/bcm4908/patches-5.4/180-i2c-brcmstb-fix-support-for-DSL-and-CM-variants.patch All other updated automatically. The new config option CONFIG_BPF_UNPRIV_DEFAULT_OFF is now handled too. Compile-tested on: lantiq/xrx200, armvirt/64 Runtime-tested on: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq806x: base-files: asrock: fix bootcount includePetr Štetiar2022-02-281-1/+1
| | | | | | | | | | | | | | | | Fixes following warning message during image building process: Finalizing root filesystem... root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory Enabling boot root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory Enabling bootcount Fixes #9350 Fixes: 98b86296e67d ("ipq806x: add support for ASRock G10") Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit fc317a190c930c9c338bd07c2e323b6b9eaa1f07)
* Revert "ramips: increase spi-max-frequency for ipTIME mt7620 devices"Sungbo Eo2022-02-271-1/+1
| | | | | | | | | | | | | | | | | | | | | This reverts commit 13a185bf8acb67da4a68873e560876c0e60b1a87. There was a report that one A1004ns device fails to detect its flash chip correctly: [ 1.470297] spi-nor spi0.0: unrecognized JEDEC id bytes: e0 10 0c 40 10 08 [ 1.484110] spi-nor: probe of spi0.0 failed with error -2 It also uses a different flash chip model: * in my hand: Winbond W25Q128FVSIG (SOIC-8) * reported: Macronix MX25L12845EMI-10G (SOP-16) Reducing spi-max-frequency solved the detection failure. Hence revert. Reported-by: Koasing <koasing@gmail.com> Tested-by: Koasing <koasing@gmail.com> Signed-off-by: Sungbo Eo <mans0n@gorani.run> (cherry picked from commit 9968a909c248169064446ed40e66d18986d93d11)
* ipq806x: base-files: asrock: fix bootcount includePetr Štetiar2022-02-261-5/+2
| | | | | | | | | | | | | | | | | | | | | | | Fixes following error while executing the init script on the buildhost: Enabling boot ./etc/init.d/bootcount: line 5: /lib/upgrade/asrock.sh: No such file or directory Enabling bootcount While at it fix following shellcheck issue: base-files/etc/init.d/bootcount line 11: if [ $? -eq 0 ]; then ^-- SC2181: Check exit code directly with e.g. 'if mycmd;', not indirectly with $?. Fixes: #9345 Cc: Ansuel Smith <ansuelsmth@gmail.com> Cc: Pawel Dembicki <paweldembicki@gmail.com> Cc: Christian Lamparter <chunkeey@gmail.com> Fixes: 98b86296e67d ("ipq806x: add support for ASRock G10") References: https://gitlab.com/ynezz/openwrt/-/jobs/1243290743#L1444 Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit ce8af0ace04bb43e8156940c771b4058fa83d27a)
* ramips: mt7621: do memory detection on KSEG1Chuanhong Guo2022-02-221-0/+62
| | | | | | | | | | | | | | | | | | | | | | | | | It's reported that current memory detection code occasionally detects larger memory under some bootloaders. Current memory detection code tests whether address space wraps around on KSEG0, which is unreliable because it's cached. Rewrite memory size detection to perform the same test on KSEG1 instead. While at it, this patch also does the following two things: 1. use a fixed pattern instead of a random function pointer as the magic value. 2. add an additional memory write and a second comparison as part of the test to prevent possible smaller memory detection result due to leftover values in memory. Fixes: 6d91ddf517 ("ramips: mt7621: add support for memory detection") Reported-by: Rui Salvaterra <rsalvaterra@gmail.com> Tested-by: Rui Salvaterra <rsalvaterra@gmail.com> Signed-off-by: Chuanhong Guo <gch981213@gmail.com> (cherry picked from commit 2f024b79331141e2a62c9bf3601c803b26bde77b) [backport for OpenWrt 21.02 as it was reproducible with Kernel 5.4, see [1]] [1]: https://forum.openwrt.org/t/113081 Tested-by: Dimitri Souza <dimitri.souza@gmail.com> [mt7621/archer-c6-v3] Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ramips: fix NAND flash driver ECC bit position maskFelix Fietkau2022-02-161-1/+1
| | | | | | | | | The bit position mask was accidentally made too wide, overlapping with the LSB from the byte position mask. This caused ECC calculation to fail for odd bytes Signed-off-by: Chad Monroe <chad.monroe@smartrg.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 918d4ab41ea34358c747aab5471bbb0a2a786dd8)
* kernel: backport fix for initializing skb->cb in the bridge code to 5.4Felix Fietkau2022-02-162-2/+30
| | | | | | | Fixes issues with proxyarp Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit dabc78b644c0fb8f17ff5456f6cb92e78b53f248)
* bcm4908: backport watchdog and I2C changesRafał Miłecki2022-02-168-13/+141
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 923cc869a6eec7dd6fdf728b2adb05824e4b9ac0)
* bcm4908: backport first 5.18 DTS changesRafał Miłecki2022-02-163-19/+211
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit da8b720b0ecbb6d58f28a31b082b0c53be149a5a)
* bcm4908: backport bcm_sf2 patch for better LED registers supportRafał Miłecki2022-02-163-2/+211
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 840f07e532e081befc2465fd16a0388dd95e55fb)
* bcm4908: backport BCM4908 pinctrl driverRafał Miłecki2022-02-163-0/+747
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit b0145891676faa38f0a5991e3e229aed7b4a9117)
* kernel: bump 5.4 to 5.4.179Hauke Mehrtens2022-02-1270-418/+151
| | | | | | | | | | | | | | | | | | | | | | | | | | Many changes were done in drivers/pinctrl/bcm/pinctrl-bcm2835.c between 5.4.171 and 5.4.179. The following 3 patches do not apply any more: * target/linux/bcm27xx/patches-5.4/950-0316-pinctrl-bcm2835-Add-support-for-BCM2711-pull-up-func.patch This was already integrated in kernel v5.4-rc1, it was never needed. * target/linux/bcm27xx/patches-5.4/950-0328-Revert-pinctrl-bcm2835-Pass-irqchip-when-adding-gpio.patch * target/linux/bcm27xx/patches-5.4/950-0362-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch I think these were done to fix the problem which was really fixed in commit 75278f1aff5e ("pinctrl: bcm2835: Change init order for gpio hogs") from v5.4.175 target/linux/generic/backport-5.4/716-v5.5-net-sfp-move-fwnode-parsing-into-sfp-bus-layer.patch Move fwnode_device_is_available to the same position as in kernel 5.10. target/linux/layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch Applied in commit 65816c1034769e714edb70f59a33bc5472d9e55f ("arm64: dts: ls1028a-qds: move rtc node to the correct i2c bus") Compile-tested: lantiq/xrx200, bcm27xx/bcm2710 Run-tested: lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: Add support for OpenMesh OM5P-AC v2Sven Eckelmann2022-02-114-34/+104
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/200 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * 4x GPIO-LEDs (3x wifi, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring * 2x ethernet - eth0 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as LAN interface - eth1 + AR8031 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 18-24V passive POE (mode B) + used as WAN interface * 12-24V 1A DC * internal antennas This device support is based on the partially working stub from commit 53c474abbdfe ("ath79: add new OF only target for QCA MIPS silicon"). Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit 1699c1dc7f26b332f868d338457abfbe716d6ba0)
* imagebuilder: fix local packages/ folderPaul Spooren2022-02-102-1/+16
| | | | | | | | | | | | | | | | | | This commit fixes commit "2999f810ff: build,IB: include kmods only in local builds" which cause the local packages/ folder only to be added for local builds but no longer for ImageBuilder created by the Buildbot. The commits intention was to use remote kmods repositories rather than storing them locally. Accidentally the entire handling of the local `packages/` was removed. Re-add the folder and include a README describing what it can be used for. Signed-off-by: Paul Spooren <mail@aparcar.org> (cherry picked from commit 15e55a2190ba087679b24b8844a51a6e4d512cf3) Fixes: #5068 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* lantiq: flag FritzBox 7360 family buttons active-lowDavid Bauer2022-01-151-2/+2
| | | | | | | | | All buttons of the FritzBox 7360 family are active-low, not active-high. Corrent the GPIO flag. This fixes release triggers upon push of a button. Reported-by: Jan-Niklas Burfeind <git@aiyionpri.me> Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 31545378641d45f5fac5ffc408a31b700b80121f)
* kernel: bump 5.4 to 5.4.171David Bauer2022-01-1316-30/+30
| | | | | | | Compile-tested: ath79-generic ipq40xx-generic Run-tested: ath79-generic Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: rb912: fix pll init issuesKoen Vandeputte2022-01-131-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | It was reported that some rb912 boards (ar934x) have issues with some ethernet speeds. Investigation shows that the board failed to adapt the ethernet pll values as shown here: [ 5.284359] ag71xx 19000000.eth: failed to read pll-handle property added custom prints in code and triggering a link switch: [ 62.821446] Atheros AG71xx: fast reset [ 62.826442] Atheros AG71xx: update pll 2 [ 62.830494] Atheros AG71xx: no pll regmap! Comparison with another very similar board (rb922 - QCA955x) showed a missing reference clock frequency in dts, which seems to cause a pll init issue. Unfortunately, no errors are printed when this occurs. Adding the frequency property fixes the pll init as it can be parsed now by the ethernet driver. [ 55.861407] Atheros AG71xx: fast reset [ 55.866403] Atheros AG71xx: update pll 2 [ 55.870462] Atheros AG71xx: ath79_set_pllval: regmap: 0x81548000, pll_reg: 0x2c, pll_val: 0x02000000 Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> (cherry picked from commit 2a000546187122c86143c97337af4d5beacc4908)
* kernel: backport workaround for Realtek RTL8672 and RTL9601C chipsVladimir Markovets2022-01-0814-37/+392
| | | | | | | | | | | | | | | Adds support for GPON SFP modules based on the Realtek RTL8672 and RTL9601C chips, including but not limited to: * V-SOL V2801F * C-Data FD511GX-RM0 * OPTON GP801R * BAUDCOM BD-1234-SFM * CPGOS03-0490 v2.0 * Ubiquiti U-Fiber Instant * EXOT EGS1 Signed-off-by: Vladimir Markovets <abam_a@yahoo.com> (cherry picked from commit f032601ed7d70fe1f468219b68750230b6ea1906)
* mvebu: remove patch that was applied into linux stableMarek Behún2022-01-082-51/+1
| | | | | | | | | | | | | | The patch PCI: aardvark: Don't touch PCIe registers if no card connected was applied into Linux stable version 5.4.163. Remove it from patches-5.4. (It applied even though it was applied already, resulting in repeated code.) Fixes: 14940aee4566 ("kernel: bump 5.4 to 5.4.163") Signed-off-by: Marek Behún <marek.behun@nic.cz>
* bcm4908: include ATF in bootfs imagesRafał Miłecki2022-01-032-0/+16
| | | | | | | It's required for proper booting. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 65974aa18bf49005509e0c31ee3f3aa6fb186015)
* kernel: backport support for multicolor & RGB LEDs to 5.4Rafał Miłecki2022-01-033-0/+153
| | | | | | | This is a requirement for backporting DT files defining such LEDs. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 85ad48c9579c0482c98fc6b69e885102511e9194)
* bcm4908: sysupgrade: add pkgtb format supportRafał Miłecki2022-01-031-2/+183
| | | | | | | | | | | | | | | BCM4908 devices with U-Boot use pkgtb firmware format. It's based on U-Boot's FIT: DTB with configurations, images & embedded data. This format contains bootfs, rootfs and optionally a first stage U-Boot loader. Contained images need to be extracted & flashed. Broadcom used two sets of firmwares: main & backup. It uses UBI volumes "metadata1" & "metadata2" for storing U-Boot env variables with info about flashed images. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 5f05795aa7716879e46fabbd0c51ff20ef9f13bf)
* bcm4908: add uboot-envtools to default packagesRafał Miłecki2022-01-031-1/+1
| | | | | | | It's required by sysupgrade to access UBI metadata partitions. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 444b4ea4a479d76761ee4833cb340b442dac662a)
* bcm4908: add fdt-utils to default packagesRafał Miłecki2022-01-031-1/+1
| | | | | | | It's required by sysupgrade. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 30b93672ec48d247fcd86b5bca283423db5250b9)
* bcm4908: sysupgrade: refactor handling different firmware formatsRafał Miłecki2022-01-031-32/+76
| | | | | | | | | | | This results in setting format specific data (format info, extract commands) in a single function. It should help maintaining sysupgrade code. This change has been tested on Asus GT-AC5300 and Netgear R8000P. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 30b168b9b8451d6165833cee75019ef7dbfd8a2e)
* ipq40xx: specify FritzBox 7530 LAN port label numbersRafał Miłecki2022-01-031-1/+1
| | | | | | | | | | This helps managing LAN ports. Ref: https://forum.openwrt.org/t/openwrt-21-02-0-second-release-candidate/98026/121 Fixes: 95b0c07a618f ("ipq40xx: add support for FritzBox 7530") Cc: David Bauer <mail@david-bauer.net> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 3342d574be08db8926273678291497769d2365e9)
* mvebu: puzzle: wan LED and fix default networkDaniel Golle2022-01-012-1/+21
| | | | | | | | | | Fix default network configuration of the Puzzle-M902 so all LAN ports are included in the LAN bridge. Setup network LED to indicate WAN port link status, like vendor firmware does as well. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit f9782f5bcd13e419abf9c84017ada27fa9764011)
* mvebu: enable Aquantia phy driver for Puzzle devicesDaniel Golle2022-01-013-15/+16
| | | | | | | | | | | | | | While on Linux 5.10 this fixes Ethernet link status on all ports and makes 2.5G ports usable in 2.5G and 1G full-duplex mode, when using Linux 5.4 and backported Aquantia phy patches, only 1G mode works on the 2.5G ports and link speed and duplex are not reported correctly from the phy in case of 2.5G. The reasons are probably trivial, but hard to find. As having all ports work at least in 1G speed instead of having them not work at all is still better, push this anyway for now. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit f81a06408eec28d479f699bd762b703ac65e2150)
* mvebu: add id for AQR112 Ethernet phy variantsDaniel Golle2022-01-011-0/+55
| | | | | | Add ids for AQR112R and AQR112C 2.5G Ethernet PHYs. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mvebu: import patch enabling AQR113 PHYDaniel Golle2022-01-011-0/+43
| | | | | | Add PHY ID for the Aquantia AQR113 PHY. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-06 19:22:55 +0000