aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* sunxi: use vendor_device scheme for device definitionsAdrian Schmutzler2019-12-134-99/+69
| | | | | | | | | | | | This changes device definition to resemble the vendor_device scheme already present for the majority of device compatible strings. By doing this, we achieve several advantages at once: - Image names and node names are more consistent with other targets. - SUPPORTED_DEVICES can be set automatically for all but two cases. - Image names and node names are in line with DEVICE_TITLEs. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link TL-WDR4300 v1 (IL)Adrian Schmutzler2019-12-124-1/+23
| | | | | | | | The TL-WDR4300 v1 sold in Israel has a different TPLINK_HWID. Thanks to Josh4300 for testing on device. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: redistribute UBNT variables in Ubiquiti image MakefileAdrian Schmutzler2019-12-121-15/+18
| | | | | | | | | | | | | The variables UBNT_BOARD and UBNT_VERSION are defined in the parent Device/ubnt definition and then overwritten for most of the derived platform definitions (e.g. Device/ubnt-wa). Since this mixed use of inheritance and overwriting can be misleading, this moves the variables to the platform-based definitions. While at it, reorder the definitions to have order consistent, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label MAC address for Mikrotik RBM33GAdrian Schmutzler2019-12-121-1/+4
| | | | | | | | | | | | | | The device label contains: E01: B8:69:F4:xx:xx:07 E02: B8:69:F4:xx:xx:09 The first value corresponds to the address set in hard_config 0x10. That one is taken for the label MAC address. Thanks to Martin Schiller for retrieving the information. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: rt305x: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-125-50/+60
| | | | | | | | | | | | | | | | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. This removes the wan_mac setup for the following devices as they do not set up a MAC address for ethernet in the first place: - asiarf,awapn2403 - belkin,f7c027 - dlink,dir-615-d - mofinetwork,mofi3500-3gn - prolink,pwh2004 - ralink,v22rw-2x2 - unbranded,wr512-3gn-4m - unbranded,wr512-3gn-8m While at it, make some DT node labels consistent with the label property. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: rt288x: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-121-4/+5
| | | | | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. This removes the wan_mac setup for ralink,v11st-fe as this device does not set up a MAC address for ethernet in the first place. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt76x8: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-122-19/+29
| | | | | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. While at it, change the partition label for zyxel,keenetic-extra-ii to factory to be consistent with node label and all the other devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7621: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-121-16/+26
| | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: mt7620: use flash location for wan_mac in 02_networkAdrian Schmutzler2019-12-121-12/+16
| | | | | | | | | | | This uses the flash locations instead of eth0 MAC address to calculate MAC address increments for WAN. The change will make the MAC address setup of a particular device more obvious and removes the dependency of 02_network on the eth0 initialization. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove wan_mac setup for evaluation boardsAdrian Schmutzler2019-12-123-6/+0
| | | | | | | | The evaluation boards do not set up a MAC address for eth0 in the first place, so it does not make sense to calculate a WAN address from the random MAC used there. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: create common DTSI for TP-Link Archer C20i/C20 v1/C50 v1Adrian Schmutzler2019-12-124-358/+137
| | | | | | | The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same, so creating a common DTSI will reduce duplicate code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove unused DTS variable from DEVICE_VARSAdrian Schmutzler2019-12-121-1/+1
| | | | | | | | | | | | | The DTS variable has been removed in 402138d12dca ("ramips: Derive DTS name from device name in Makefile"), but the DEVICE_VARS entry has been overlooked. Remove it now since we are not using this variable. This must _not_ be backported to 19.07, where the variable is still in use. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix switch port numbering for RT-AC65P/RT-AC85PGabor Varga2019-12-111-2/+2
| | | | | | | | | | | The switch LAN port numbers are in reversed order with original config. With this patch they are fixed. Port order checked on both devices. Signed-off-by: Gabor Varga <vargagab@gmail.com> [merged definitions into appropriate block, extended commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add label MAC address for TP-Link Archer C20iAdrian Schmutzler2019-12-111-0/+4
| | | | | | | | | | | | | | Current OpenWrt MAC setup: eth0 &rom 0xf100 :48 eth0.2 eth0+1 :49 wlan0 (5 GHz) &radio 0x8004 different OUI wlan1 (2.4 GHz) &radio 0x4 same OUI as wlan0 Label MAC address corresponds to eth0 (&ethernet). No additional addresses found in hexdump of rom/radio. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix typos in DTSDENG Qingfang2019-12-114-11/+11
| | | | | | Replace "usb_ochi" with "usb_ohci", and "usb_echi" with "usb_ehci". Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* kernel: bump 4.19 to 4.19.88Koen Vandeputte2019-12-1025-356/+55
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 0004-boot-sq201-from-sda1.patch - 500-v4.20-ubifs-Fix-default-compression-selection-in-ubifs.patch - 0003-usb-dwc2-use-a-longer-core-rest-timeout-in-dwc2_core.patch Altered patches: - 0011-ARM-dts-Fix-up-SQ201-flash-access.patch - 400-mtd-add-rootfs-split-support.patch - 0101-pci-mediatek-backport-fix-pcie.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.158Koen Vandeputte2019-12-1020-40/+40
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 400-mtd-add-rootfs-split-support.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.206Koen Vandeputte2019-12-1016-45/+45
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 400-mtd-add-rootfs-split-support.patch Compile-tested on: none Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* malta: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* sunxi: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* layerscape: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kirkwood: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* at91: disable legacy PTYs and virtual terminalsDaniel Golle2019-12-091-6/+0
| | | | | | | | | Enabling legacy PTYs causes problems with procd-hotplug. And as this is a headless target, no need to have virtual terminals. Remove corresponding kernel config options, they are disabled in generic kernel config. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mpc85xx: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ixp4xx: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-091-2/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* uml: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: disable legacy PTYs and virtual terminalsDaniel Golle2019-12-091-6/+0
| | | | | | | | | Enabling legacy PTYs causes problems with procd-hotplug. And as this is a headless target, no need to have virtual terminals. Remove corresponding kernel config options, they are disabled in generic kernel config. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* treewide: remove dts-v1 identifier from DTSI filesAdrian Schmutzler2019-12-0846-49/+0
| | | | | | | | | | | | | | | | The "/dts-v1/;" identifier is supposed to be put once at the beginning of a device tree file. Thus, it makes no sense to provide it a second time in to-be-included DTSI files. This removes the identifier from all DTSI files in /target/linux. Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is missing for most of the following targets, though: mvebu, ipq806x, mpc85xx, ipq40xx This does not touch ipq806x for now, as the bump to 4.19 is close. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* brcm47xx: add switch configuration for WNR3500LOlli Asikainen2019-12-081-1/+2
| | | | | | | | | | | | | | | | | | | | Netgear WNR3500L is an already supported device, but out of the box, the device has no switch configuration and there is no wan. The correct configuration for this specific model is similar to some other models. This simple commit adds the correct switch and the out-of-the-box experience is improved. Experimentally determined: Port 0 => WAN Port 1..4 => LAN Port 5..7 => unused Port 8 => CPU Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com> Tested-by: Fabian Zaremba <fabian@youremail.eu> [added port mapping to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: convert mediatek,mtd-eeprom from decimal to hex notationAdrian Schmutzler2019-12-083-6/+6
| | | | | | | | | | A small subset of devices uses decimal notation for mediatek,mtd-eeprom in DTS files. Convert to hexadecimal notation to be consistent with all the rest. Also change "0" to "0x0" in the same files for consistency. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix number of LAN Ports for Mikrotik RBM33GMartin Schiller2019-12-081-1/+4
| | | | | | | | The Mikrotik RBM33G has only 2 LAN ports. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [moved node in 02_network to maintain alphabetic sorting] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix switch port order for TP-Link Archer C20iWalter Sonius2019-12-081-1/+1
| | | | | | | | | | | | | | | | | | Physical port order watched from the backside of the C20i (from left to right) is: Internet / 1 / 2 / 3 / 4 Physical Port Switch port WAN 0 LAN 3 1 LAN 4 2 LAN 1 3 LAN 2 4 (not used) 5 CPU 6 Signed-off-by: Walter Sonius <walterav1984@gmail.com> [commit message/title improvements] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix WNDR3700/WNDR3800 wifi reg sizeChristian Lamparter2019-12-071-2/+2
| | | | | | | | "[...] the size component shall be zero." (See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1" section "4.1.1 Open Firmware-defined Properties for Child Nodes") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mediatek: fix pcie bringup issueJohn Crispin2019-12-051-0/+9
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ath79: add support for Ubiquiti LiteBeam AC Gen2Stijn Tintel2019-12-044-0/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: drop IMAGE/factory.bin from ubnt-wa devicesStijn Tintel2019-12-041-4/+0
| | | | | | | | | | The sysupgrade image contains OpenWrt specific metadata. Having this metadata in the factory images makes no sense. Drop IMAGE/factory.bin from Device/ubnt-wa and use the default from Device/ubnt instead. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: act_ctinfo: fix updated backport on 4.14Kevin Darbyshire-Bryant2019-12-041-21/+8
| | | | | | | | It turns out my 4.14 testing had a rather large flaw in it and the 'extack' mechanism isn't quite ready. Remove the extack stuff from this backport. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: act_ctinfo: update backportKevin Darbyshire-Bryant2019-12-032-72/+210
| | | | | | | | | | Since the original backports from kernel 5.3 a few things have been tweaked by kernel bumps & other upstream changes. Update the backport to reflect upstream as closely as possible and remove the bitrot. Functions remain the same, error reporting improved. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: fix source of label MAC address for Ubiquiti XM devicesAdrian Schmutzler2019-12-031-6/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In d421a8b94489 ("ath79: read label MAC address from flash instead of using phy0/phy1") the source of the label MAC address was changed for devices just reading it from phy0. To get rid of the dependency from phy startup, addresses were read directly from the flash locations that are used to initialize the phy MAC addresses. Unfortunately, it turned out that Ubiquiti XM devices seem to have different flash locations than expected, and also seem to have specific locations for different devices (all in art/EEPROM): 0xe012 AR9280 Nanostation M2 - 0x120c 0xe035 AR9280 Nanostation M3 - 0x120c 0xe1b2 AR9280 Rocket M2 - 0x120c 0xe1c3 AR9280 Rocket M3 - 0x120c 0xe1b5 AR9280 Rocket M5 - 0x120c 0xe2d5 AR9280 Bullet M2 Titanium - 0x120c 0xe2b5 AR9280 Nanobridge M5 - 0x120c 0xe202 AR9280 Bullet M2 - 0x120c 0xe232 AR9287 Nanobridge M2 - 0x110c 0xe4a2 AR9285 AirRouter - 0xa0bf Picostation M2 - 0x120c and 0xa0bf Nanostation Loco M2 - not in 0x120c, other locations not checked An additional problem of the Ubiquiti device support in OpenWrt is that we provide images that match several subvariants of the devices, which might have different MAC address locations. Given that reading the address from phy0 in 02_network _is_ working for the ath79 target in general, it does not seem reasonable to rebuild a complex MAC address retrieval mechanism which is already present in the ath9k driver. So, this patch reverts the label MAC address source for Ubiquiti XM devices (and the Unifi AP) to /sys/class/ieee80211/phy0/macaddress. This doesn't affect XW and Unifi AC devices, where the label MAC address source is defined via device tree. For alfa-network,ap121f the location 0x1002 is kept, as this has been verified during device support preparation in PR #2199. Fixes: d421a8b94489 ("ath79: read label MAC address from flash instead of using phy0/phy1") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* octeon: fix sysupgradeStijn Tintel2019-11-301-2/+2
| | | | | | | | Sysupgrade was failing due to incorrect replacement of backticks: /sbin/sysupgrade: /lib/upgrade/platform.sh: line 101: syntax error: missing '))' Fixes: 0bbfc3dff719 ("octeon: replace backticks by $(...)") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* generic ar8xxx: increase VLAN table for AR83x7David Bauer2019-11-303-9/+13
| | | | | | | | | | | | The Atheros AR8327 and AR8337 have (according to their datasheet) a VLAN table with a maximum of 4096 entries. Currently, there's a hard limit of 128 VLANs, which is the same as for most other Atheros switches. Increase this limit only for the AR83x7 series and modify some shared functions to allow them to work with a variable max VLAN count. Signed-off-by: David Bauer <mail@david-bauer.net>
* mac80211: switch to upstream owl-loader driverChristian Lamparter2019-11-304-402/+0
| | | | | | | | | | | | | | | | | | The Owl Loader (named after the codename that Atheros gave these devices back in the day) has been accepted upstream. This patch removes the "misc" driver OpenWrt had and adds the remaining differences against the version that ships with 5.4-rc1 into a separate "120-owl-loader-compat.patch" file that can be cut down once AR71XX is being dealt with. Note: I decided to keep the existing (kmod-)owl-loader package name around for now. The kernel module file in the kmod package will be called ath9k_pci_owl_loader.ko though. Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Crisis Innovation Lab MeshPoint.OneRobert Marko2019-11-307-4/+110
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon Jalapeno module from 8Devices). MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and smart city gateway that can be installed and powered from street lighting (even solar power in the future). MeshPoint provides up to 27 hours of interrupted Wi-Fi and IoT services from internal battery even when external power is not available. MeshPoint.One can be used for disaster relief efforts in order to provide instant Wi-Fi coverage that can be easily expanded by just adding more devices that create wide area mesh network. MeshPoint.One devices have standard Luci UI for management. Features: - 1x 1Gpbs WAN - 1x 1Gbps LAN - POE input (eth0) - POE output (eth1) - Sensor for temperature, humidity and pressure (Bosch BME280) - current, voltage and power measurement via TI INA230 - Hardware real time clock - optional power via Li-Ion battery - micro USB port with USB to serial chip for easy OpenWrt terminal access - I2C header for connecting additional sensors Installation: ------------- Simply flash the sysupgrade image from stock firmware. Or use the built in Web recovery into bootloader: Hold Reset button for 5 to 20 seconds or use UART and httpd command. Web UI will appear on 192.168.2.100 by default. For web recovery use the factory.ubi image. Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr> Signed-off-by: Damir Franusic <damir.franusic@sartura.hr> Signed-off-by: Valent Turkovic <valent@meshpoint.me> Signed-off-by: Robert Marko <robert@meshpoint.me> [commit description long line wrap, usb->USB] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: use DTSI for JalapenoRobert Marko2019-11-302-260/+272
| | | | | | | | | | | | Lets move common code for Jalapeno into DTSI, this way Jalapeno based boards don't introduce duplicate code. While at it, lets also fix some style issues and update to current DTS style. Signed-off-by: Robert Marko <robert@meshpoint.me> [commit description long line wrap] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.9 to 4.9.205Koen Vandeputte2019-11-292-5/+5
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2019-18660 Compile-tested on: none Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.86Koen Vandeputte2019-11-2916-223/+44
| | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0064-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch - 0005-mtd-physmap_of-Move-custom-initialization.patch Remove upstreamed: - 0001-pinctrl-gemini-Mask-and-set-properly.patch - 0002-pinctrl-gemini-Fix-up-TVC-clock-group.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.156Koen Vandeputte2019-11-2923-61/+61
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mpc85xx: add vendor to Makefile node name, derive SUPPORTED_DEVICESAdrian Schmutzler2019-11-271-15/+13
| | | | | | | | | | | | | | By adding the vendor to the Makefile device definition node name, one can derive the standard compatible used in SUPPORTED_DEVICES instead of having to specify it manually. Despite, this moves the naming scheme closer to what is used for other targets (ath79, ramips). Build-tested on all subtargets. Run-tested on TP-Link TL-WDR4900 v1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: add support for TP-Link Archer C6 v2 (US) and A6 (US/TW)Anderson Vulczak2019-11-277-120/+270
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch is based on #1689 and adds support for TP-Link Archer C6 v2 (US) and A6 (US/TW). The hardware is the same as EU and RU variant, except for GPIOs (LEDS/Buttons), flash(chip/partitions) and UART being available on the board. - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q127CS1G (16MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: 115200, 8n1 (header available on board) Known issues: - Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range. Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherA6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing Flash partitioning: I've followed #1689 for defining the partition layout for this patch. The partition named as "tplink" @ 0xfd0000 is marked as read only as it is where some config for stock firmware are stored. On stock firmware those stock partitions starts at 0xfd9400 however I had not been able to make it functional starting on the same address as on stock fw, so it has been partitioned following #1689 and not the stock partition layout for this specific partition. Due to that firmware/rootfs partition lenght is 0xf80000 and not 0xf89400 as stock. According to the GPL code, the EU/RU/JP variant does have different GPIO pins assignment to LEDs and buttons, also the flash memory layout is different. GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz Signed-off-by: Anderson Vulczak <andi@andi.com.br> [wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: rename EEPROM to artAdrian Schmutzler2019-11-2711-33/+31
| | | | | | | | | | | | | This renames all remaining occurrences of "EEPROM" to "art" to further harmonize the partition labelling in ath79. This will help to reduce the amount of user-space code and might be beneficial when code is copy/pasted in the future. Affected are only devices from Ubiquiti, where the XM board is already using "art" in ath79. Acked-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-27 08:16:07 +0000