aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* mvebu: Fix sysupgrade for GL.iNet GL-MV1000Sven Eckelmann2021-04-181-0/+3
| | | | | | | | | | | | The GL.iNet GL-MV1000 is booting from eMMC and the images for it are in theory sysupgrade compatible. But the platform upgrade scripts were not adjusted to select the mmcblock device as upgrade target. This resulted in a failed sysupgrade because the mtd device (NOR flash) was instead tried to be modified by the sysupgrade script. Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit 07e5e03711d55f94db738446ef9eddc8163b53a6)
* ramips: Fix booting on MTC WR1201René van Dorst2021-04-181-0/+1
| | | | | | | | | This fixes the dreaded "lzma error 1" also reported on similar devices Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057 Fixes: FS#3057 Signed-off-by: René van Dorst <opensource@vdorst.com> (cherry picked from commit 12f3d1466ad783fded1747fa2ee521a9bea1ff73)
* ramips: Fix booting on MQmaker WiTi boardDaniel Engberg2021-04-181-0/+1
| | | | | | | | | This fixes the dreaded "lzma error 1" also reported on similar devices Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3057 Fixes: FS#3057 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> (cherry picked from commit e83f7e5d76ebf74aa0a1f686d2941950fa5f22e2)
* ramips: rt305x: use lzma-loader for ZyXEL Keenetic Lite rev.BSzabolcs Hubai2021-04-181-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes boot loader LZMA decompression issue, reported by GitHub user KOLANICH at [0]. The reported LZMA ERROR has date of 2020-07-20, soon after the device support landed: Ralink UBoot Version: 3.5.2.4_ZyXEL .... 3: System Boot system code via Flash. Image Name: MIPS OpenWrt Linux-4.14.187 Created: 2020-07-20 3:39:11 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1472250 Bytes = 1.4 MB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover [0] https://github.com/openwrt/openwrt/commit/fea232ae8feb6af780fd4fa78ebe9231778bf75a#commitcomment-45016560 Fixes: 4dc9ad4af8c921494d20b303b6772fc6b5af3a69 ("ramips: add support for ZyXEL Keenetic Lite Rev.B") Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com> (cherry picked from commit dd3c1ad8ee9ee361285cb9142bdcb35bc3a30ac7)
* bcm53xx: add pending TRX patch for "firmware" partitionRafał Miłecki2021-04-161-0/+43
| | | | | | | | This fixes partitioning on Linksys EA9500. With this change only the currently used firmware MTD partition gets parsed. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit a3c7633ddcd4fac9ec8935e5be9249c011bfec14)
* gemini,layerscape,oxnas: don't disable option CONFIG_BPF_SYSCALLTony Ambardar2021-04-164-4/+0
| | | | | | | | | | Respect the generic kernel config setting, which is "enabled" tree-wide, as previously done for sunxi. Ref: 247ef4d98bab ("sunxi: enable CONFIG_BPF_SYSCALL and CONFIG_EMBEDDED") Signed-off-by: Tony Ambardar <itugrok@yahoo.com> (cherry picked from commit 41948c9c1b80e39f2fd2771f42e62e209347b0bf) Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ath79: mikrotik: enable 2nd USB on RouterBOARD 922UAGS-5HPacDKoen Vandeputte2021-04-121-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | RB922 boards have 2 separate USB controllers: - 1 is connected to Slot Type A - 1 is connected to the mini PCIe port Enable the 2nd one too. Before: [ 5.339304] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.355053] SCSI subsystem initialized [ 5.364184] ehci-fsl: Freescale EHCI Host controller driver [ 5.372377] ehci-platform: EHCI generic platform driver [ 5.378053] ehci-platform 1b000000.usb: EHCI Host Controller [ 5.383861] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 5.391932] ehci-platform 1b000000.usb: irq 14, io mem 0x1b000000 [ 5.410730] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 5.417739] hub 1-0:1.0: USB hub found [ 5.422280] hub 1-0:1.0: 1 port detected [ 5.434007] usbcore: registered new interface driver usb-storage After: [ 5.342988] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.358687] SCSI subsystem initialized [ 5.367813] ehci-fsl: Freescale EHCI Host controller driver [ 5.375998] ehci-platform: EHCI generic platform driver [ 5.381695] ehci-platform 1b000000.usb: EHCI Host Controller [ 5.387507] ehci-platform 1b000000.usb: new USB bus registered, assigned bus number 1 [ 5.395571] ehci-platform 1b000000.usb: irq 14, io mem 0x1b000000 [ 5.416050] ehci-platform 1b000000.usb: USB 2.0 started, EHCI 1.00 [ 5.423089] hub 1-0:1.0: USB hub found [ 5.427578] hub 1-0:1.0: 1 port detected [ 5.432432] ehci-platform 1b400000.usb: EHCI Host Controller [ 5.438254] ehci-platform 1b400000.usb: new USB bus registered, assigned bus number 2 [ 5.446325] ehci-platform 1b400000.usb: irq 15, io mem 0x1b400000 [ 5.468049] ehci-platform 1b400000.usb: USB 2.0 started, EHCI 1.00 [ 5.475082] hub 2-0:1.0: USB hub found [ 5.479574] hub 2-0:1.0: 1 port detected [ 5.491305] usbcore: registered new interface driver usb-storage Fixes: 8f93c05a59 ("ath79: add support for MikroTik RouterBOARD 922UAGS-5HPacD") Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com> (cherry picked from commit 172fa3bc7544ce940ce724d682d66109a3e14a11)
* kernel: bump 5.4 to 5.4.111Hauke Mehrtens2021-04-1173-248/+248
| | | | | | | | | | | | | | | | | | | | | Refreshed all patches. The following patches were manually changed: * 610-netfilter_match_bypass_default_checks.patch * 611-netfilter_match_bypass_default_table.patch * 802-can-0002-can-rx-offload-fix-long-lines.patch * 802-can-0003-can-rx-offload-can_rx_offload_compare-fix-typo.patch * 802-can-0004-can-rx-offload-can_rx_offload_irq_offload_timestamp-.patch * 802-can-0005-can-rx-offload-can_rx_offload_reset-remove-no-op-fun.patch * 802-can-0006-can-rx-offload-Prepare-for-CAN-FD-support.patch * 802-can-0018-can-flexcan-use-struct-canfd_frame-for-CAN-classic-f.patch The can-dev.ko model was moved in the upstream kernel. Compile-tested on: x86/64, armvirt/64, ath79/generic Runtime-tested on: x86/64, armvirt/64, ath79/generic Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2021-04-1126-66/+12
| | | | | | | Move some disabled symbols found in armvirt target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> (cherry picked from commit 12e942b1fdda874542e0a4e6ea892969fedab975)
* sunxi: disable LPAE on cortexa8Zoltan HERPAI2021-04-111-0/+2
| | | | | | | LPAE should be disabled as the Cortex-A8 cores don't support it, and the kernel will crash on boot if it's enabled. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* kernel: DSA roaming fix for Marvell mv88e6xxxDENG Qingfang2021-04-1015-0/+1180
| | | | | | | | | | | | | | | | | | | | | | | | | | Marvell mv88e6xxx switch series cannot perform MAC learning from CPU-injected (FROM_CPU) DSA frames, which results in 2 issues. - excessive flooding, due to the fact that DSA treats those addresses as unknown - the risk of stale routes, which can lead to temporary packet loss Backport those patch series from netdev mailing list, which solve these issues by adding and clearing static entries to the switch's FDB. Add a hack patch to set default VID to 1 in port_fdb_{add,del}. Otherwise the static entries will be added to the switch's private FDB if VLAN filtering disabled, which will not work. The switch may generate an "ATU violation" warning when a client moves from the CPU port to a switch port because the static ATU entry added by DSA core still points to the CPU port. DSA core will then clear the static entry so it is not fatal. Disable the warning so it will not confuse users. Link: https://lore.kernel.org/netdev/20210106095136.224739-1-olteanv@gmail.com/ Link: https://lore.kernel.org/netdev/20210116012515.3152-1-tobias@waldekranz.com/ Ref: https://gitlab.nic.cz/turris/turris-build/-/issues/165 Signed-off-by: DENG Qingfang <dqfext@gmail.com> (cherry picked from commit 920eaab1d8179035d0ae1047e75cf9a50da6a6eb)
* x86/base-files: add support for Sophos SG/XG-105Stan Grishin2021-04-102-0/+11
| | | | | | | | This adds detection of the Sophos SG-105 and Sophos XG-105 models and assignment of ethernet ports these models have to LAN/WAN. Signed-off-by: Stan Grishin <stangri@melmac.net> (cherry picked from commit 64eaf633ff7f9280e04e65ae290eb8b65dd9e021)
* kernel: 5.4: import wireguard backportJason A. Donenfeld2021-04-10132-32/+63296
| | | | | | | | | | | | | | | | | | | | | | | | | | Rather than using the clunky, old, slower wireguard-linux-compat out of tree module, this commit does a patch-by-patch backport of upstream's wireguard to 5.4. This specific backport is in widespread use, being part of SUSE's enterprise kernel, Oracle's enterprise kernel, Google's Android kernel, Gentoo's distro kernel, and probably more I've forgotten about. It's definately the "more proper" way of adding wireguard to a kernel than the ugly compat.h hell of the wireguard-linux-compat repo. And most importantly for OpenWRT, it allows using the same module configuration code for 5.10 as for 5.4, with no need for bifurcation. These patches are from the backport tree which is maintained in the open here: https://git.zx2c4.com/wireguard-linux/log/?h=backport-5.4.y I'll be sending PRs to update this as needed. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> (cherry picked from commit 3888fa78802354ab7bbd19b7d061fd80a16ce06b) (cherry picked from commit d54072587146dd0db9bb52b513234d944edabda3) (cherry picked from commit 196f3d586f11d96ba4ab60068cfb12420bcd20fd) (cherry picked from commit 3500fd7938a6d0c0e320295f0aa2fa34b1ebc08d) (cherry picked from commit 23b801d3ba57e34cc609ea40982c7fbed08164e9) (cherry picked from commit 0c0cb97da7f5cc06919449131dd57ed805f8f78d) (cherry picked from commit 2a27f6f90a430342cdbe84806e8b10acff446a2d) Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
* zynq: Enable CONFIG_KERNEL_MODE_NEONIlya Lipnitskiy2021-04-101-1/+0
| | | | | | | | | This flag is set on all other platforms. And Zynq 7000 SoC does have NEON support: https://www.xilinx.com/support/documentation/application_notes/xapp1206-boost-sw-performance-zynq7soc-w-neon.pdf Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> (cherry picked from commit 7d00f632b7b245bcf25783797308325aa255b020)
* bcm4908: enable Netgear R8000P bootloader imageRafał Miłecki2021-04-081-2/+2
| | | | | | | | | | | | | | | | | | | This enables building BCM4908 "raw" image that can be flashed using bootloader web UI. It requires serial console access & stopping booting by the "Press any key to stop auto run". It's easy to build vendor like CHK image but it can't be safely flashed using vendor UI at this point. Netgear implements method called "NAND incremental flashing" that doesn't seem to flash bootfs partition as provided. Above method seems to update vmlinux.lz without updating 94908.dtb. It prevents OpenWrt kernel from booting due to incomplete DTB file. Full Netgear R8000P support can be enabled after finding a way to make vendor firmware flash OpenWrt firmware including the 94908.dtb update. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit d92a9c97bf3700e90af1d3c9157502af660365c0)
* bcm4908: enable target & Asus GT-AC5300 imageRafał Miłecki2021-04-082-1/+3
| | | | | | | | | | OpenWrt was succesfully tested on the GT-AC5300 model. It's possible to: 1. Install OpenWrt using vendor UI 2. Perform UBI aware sysupgrade 3. Install vendor firmware using OpenWrt sysupgrade Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 5e78cb9b85a045f436abf6a03aa5c774d30e1090)
* firmware-utils: bcm4908img: convert into a packageRafał Miłecki2021-04-081-1/+3
| | | | | | | | | | | bcm4908img is a tool managing BCM4908 platform images. It's used for creating them as well as checking, modifying and extracting data from. It's required by both: host (for building firmware images) and target (for sysupgrade purposes). Make it a host/target package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 9b4fc4cae9fa0cd0cd9060e1c9d33320c3249ced)
* bcm4908: fix Netgear R8000P imageRafał Miłecki2021-04-081-2/+5
| | | | | | | Use vendor format to allow flashing using Negear UI. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit f2c8c62d98f2137d8af896e56d5e29759cf48715)
* bcm4908: add sysupgrade supportRafał Miłecki2021-04-081-0/+213
| | | | | | | | | | | It supports flashing OpenWrt images (bootfs & UBI upgrade) as well as vendor images (whole MTD partition write). Upgrading cferom is unsupported. It requires copying device specific data (like MAC) to target image before flashing. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit a6a0b252baa6c19dfc62611ea910b56527ce4fa5)
* bcm4908: pad firmware image bootfs JFFS2 partition to 8 MiBRafał Miłecki2021-04-081-1/+1
| | | | | | | | | | This way MTD "bootfs" partition will be always 8+ MiB. This should be enough for any custom / future firmware to fit its bootfs (e.g. big kernel) without having to repertition whole flash. That way we can preserve UBI and its erase counters during sysupgrade. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit ca9b1f15c424d68af0f372c37c8eee81b36ee7e1)
* bcm4908: rename bootfs dummy file to the 1-openwrtRafał Miłecki2021-04-081-1/+1
| | | | | | | | | | | | | The purpose of that dummy file is to make CFE work properly with OpenWrt bootfs. CFE for some reason ignores JFFS2 files with ino 0. Rename it to 1-openwrt so: 1. It's consistent with bcm63xx 2. It's OpenWrt specific so sysupgrade can distinguish it from vendor images Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 880c8b44223c9cbce3dd14da78c33676c6f1a8a6)
* bcm4908: enable JFFS2 supportRafał Miłecki2021-04-081-1/+0
| | | | | | | It's needed for accessing JFFS2 bootfs partition. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 180c4635265b4907221a62b3068ac89447cd83d7)
* bcm4908: backport DT patch adding Ethernet MAC addressRafał Miłecki2021-04-081-0/+82
| | | | | | | | This tells OS (Linux) where from MAC should be read (bootloader MTD partition). Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 1cc5eb45d5192b41d97d5da58c34353f4c3240f9)
* kernel: create bootfs partition when parsing on BCM4908Rafał Miłecki2021-04-081-5/+9
| | | | | | | | | It's helpful for accessing booting data (DTS, kernel, etc.). It has to be used carefully as CFE's JFFS2 support is quite dumb. It doesn't recognize deleted files and has problems handling 0 inode. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 6dd727ac24fa36ac3f23e9a5cf6781a7d1c6b797)
* bcm4908: backport the latest bcm_sf2 commitsRafał Miłecki2021-04-086-111/+210
| | | | | | | | 1. CFP support for BCM4908 2. Upstream RGMII regs fix Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit a49fd9db0a2bfad8ea9a09f32fadbd3cc7e46205)
* bcm4908: backport DTS patch with Ethernet TX IRQRafał Miłecki2021-04-082-1/+31
| | | | | | | It allows bcm4908_enet Linux driver to work more efficiently. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 13d9904acdd24e002aab3d6c3dd7879826b54008)
* bcm53xx: enhance support for Linksys EA9500Vivek Unune2021-04-084-3/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 1. Add leds and configs 2. Add network configs 3. Add script to clear partial boot flag 4. Hack to use port 5 as cpu port as port 8 connected to eth2 wont pass any frames 5. Enable EA9500 image generation Hardware Info: - Processor - Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz - Switch - BCM53012 in BCM4709C0KFEBG & external BCM53125 - DDR3 RAM - 256 MB - Flash - 128 MB (Toshiba TC58BVG0S3HTA00) - 2.4GHz - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - Skyworks SE2623L 2.4 GHz power amp (x4) - 5GHz x 2 - BCM4366 4×4 2.4/5G single chip 802.11ac SoC - Power Amp - PLX Technology PEX8603 3-lane, 3-port PCIe switch - Ports - 8 Ports, 1 WAN Ports - Antennas - 8 Antennas - Serial Port - @j6 [GND,TX,RX] (VCC NC) 115200 8n1 Flashing Instructions: 1. Connect a USB-TTL table to J6 on the router as well as a ethernet cable to a lan port and your PC. 2. Power-on the router. 3. Use putty or a serial port program to view the terminal. Hit Ctrl+C and interrupt the CFE terminal terminal. 4. Setup a TFTP server on your local machine at setup you local IP to 192.168.1.2 5. Start the TFTP Server 6. Run following commands at the CFE terminal flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx flash -noheader 192.168.1.2:/openwrt.trx nflash0.trx2 nvram set bootpartition=0 && nvram set partialboots=0 && nvram commit 7. Reboot router to be presented by OpenWrt Note: Only installation method via serial cable is supported at the moment. The trx firmware has to be flashed to both the partitions using following commands from CFE prompt. This will cover US and Non-US variants. Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 209c5918b511d9e406a094ba246a985b640e519f)
* bcm53xx: use upstream Linksys EA9500 fixesRafał Miłecki2021-04-082-1/+30
| | | | | | | One fix was accepted, one was added. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 22369ad7887e98bdb9d1999f221dfcd5fbb2f389)
* bcm53xx: fix Linksys EA9500 partitionsRafał Miłecki2021-04-081-0/+58
| | | | | | | Use proper DT binding. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit f8669c174ee17bbb8d59f901d639f57449dcf751)
* bcm53xx: backport Linksys Panamera (EA9500) patchesVivek Unune2021-04-085-2/+230
| | | | | | | | | | | | | | | | | These patches have been already accepted. 302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch had to be updated. [rmilecki: use actual upstream accepted patches replace v5.10 with v5.11 to match actual upstream kernel recover dropped part of the pinctrl compatible patch update filenames refresh patches] Signed-off-by: Vivek Unune <npcomplete13@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 39ed2265dde1bc8817f9dc6ba053268bb6939ae6)
* kernel: backport 5.13 mtd partitioning changesRafał Miłecki2021-04-0814-27/+324
| | | | | | | | | 1. Use upstream accepted NVMEM patches 2. Minor fix for BCM4908 partitioning 3. Support for Linksys firmware partitions on Northstar Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 3fd0a4222b6efbfbdb560c5b13e899ecda627494)
* generic: add missing symbolsDavid Bauer2021-04-031-0/+1
| | | | | Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 55ed4bf6d7bf80b705d015c3b73f772db485ba9c)
* ath79: fix label_mac for NEC Aterm WG1200CRINAGAKI Hiroshi2021-04-021-2/+6
| | | | | | | | | | | On NEC Aterm WG1200CR, the MAC address for WAN is printed in the label on the case, not LAN. This patch fixes this issue. Fixes: 50fdc0374b ("ath79: provide label MAC address") Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (cherry picked from commit e2331fb5491e52e3e21ab18b58d064b344e093e5)
* ramips: correct switch config of Youku yk1Shiji Yang2021-04-021-1/+4
| | | | | | | | | | | There are only two lan ports and one wan port on Youku yk1 Fixes: e9baf8265bb8 ("ramips: add support for Youku YK1") Signed-off-by: Shiji Yang <yangshiji66@qq.com> [add Fixes:] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit b88d2850c66d7dc937e570661a047c647c588af5)
* ipq40xx: net: phy: qca807x: fix GPIO driverRobert Marko2021-03-291-0/+1
| | | | | | | | | | | | While rebasing into setting bits instead of magic values, I accidentally forgot to actually set the force bit. Without it using the pins as GPIO-s did not actually work. Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver") Signed-off-by: Robert Marko <robert.marko@sartura.hr> (cherry picked from commit 7f2d9ccd09a1d3034aaf9c943747fc1631da5cac)
* ath79: fix RS-485 on Teltonika RUT-955Daniel Golle2021-03-293-14/+6
| | | | | | | | | | DTR GPIO isn't actually needed and triggers boot warning. TX pin was off by one (GPIO 19 instead of GPIO 18). Reported-by: @tophirsch Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 53a7d5d614050a38a4e78f5a9e153e7612d587f0)
* lantiq: set maximum kernel size for ARV7519RW22Aleksander Jan Bajkowski2021-03-291-0/+2
| | | | | | | | | | | Some users report that current snapshot producies non-bootable images. Stock uboot can boot images if the kernel is smaller than 2MB. Set maximum kernel size and disable image building for this board. Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843 Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> (cherry picked from commit c027dbac5a5222e6be4706a7a6a0effefce8ae76)
* mvebu: Fix mac addresses for GL.iNet GL-MV1000Sven Eckelmann2021-03-291-0/+4
| | | | | | | | | | | | | | The original GL.iNet firmware has two different mac addresses in the factory/art partition. The first one is for the WAN interface only and the second one is for both lan0 and lan1. But the original submission for OpenWrt didn't initialize the mac addresses of the LAN ports for the DSA device at all. The ethernet mac address was then used for all DSA ports. Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit c20ac84803242e5a6451184009dabc36ba83b96e)
* mvebu: Add button support for GL.iNet GL-MV1000Sven Eckelmann2021-03-291-0/+17
| | | | | | | | | | | | | | The original patch to support this device advertised support for the reset button and the "switch" in the commit message. But neither were actually integrated in the device tree or documented anywere. The button itself is now used to trigger a reset (as described in the official GL.iNet documentation). The switch itself is registered as BTN_0 like other devices from GL.iNet in ath79. Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000") Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit 01b911a9381426314762822f97e3a7e658295f50)
* mvebu: enable WRT1900AC v1 and WRT32X for buildbotsTad Davanzo2021-03-291-2/+0
| | | | | | | | Kernel size limits have been dealt with. Effective revert of a1eb2c46 and ac9730c4. Signed-off-by: Tad Davanzo <tad@spotco.us> (cherry picked from commit b4f76d9f0d61779b5e04228d1eb3f2ba412ffd26)
* mvebu: venom resize kernel to 6MBTad Davanzo2021-03-293-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | venom has a 3MB kernel partition as specified by the DTS. 3MB is not sufficient for building with many kernel modules or newer kernel versions. venom uboot however as set from factory will load up to 6MB. This can be observed by looking a uboot log: NAND read: device 0 offset 0x900000, size 0x600000 6291456 bytes read: OK and from uboot environment variables: $ fw_printenv | grep "priKernSize"; priKernSize=0x0600000 Resize the root partitions from 120MB to 117MB to let kernel expand into it another 3MB. And set kernel target size to 6MB. Lastly set the kernel-size-migration compatibility version on venom to prevent sysupgrading without first reinstalling from a factory image. Signed-off-by: Tad Davanzo <tad@spotco.us> (cherry picked from commit 15309f5133d55e92bec3ed91dfb3ac9d124f6a96)
* mvebu: mamba resize kernel to 4MBTad Davanzo2021-03-293-2/+55
| | | | | | | | | | | | | | | | | | | | | | | | | mamba has a 3MB kernel partition as specified by the DTS. 3MB is not sufficient for building with many kernel modules or newer kernel versions. mamba uboot however as set from factory will load up to 4MB. This can be observed by looking a uboot log: NAND read: device 0 offset 0xa00000, size 0x400000 4194304 bytes read: OK and from uboot environment variables: $ fw_printenv | grep "pri_kern_size"; pri_kern_size=0x400000 Resize the root partitions from 37MB to 36MB to let kernel expand into it another 1MB. And set kernel target size to 4MB. Lastly add a compatibility version message: kernel-size-migration. And set it on mamba to prevent sysupgrading without first reinstalling from a factory image. Signed-off-by: Tad Davanzo <tad@spotco.us> (cherry picked from commit 10415d5e7016b69dc71c5f1b03e8e17b586f8edd)
* kernel: backports: mt7530: fix TRGMII mode after resetIlya Lipnitskiy2021-03-292-3/+87
| | | | | | | | | | | Backport upstream patch that fixes TRGMII mode now that mt7530 is actually resetting the switch on ramips devices. Patches apply to both Linux 5.4 and 5.10, since TRGMII is broken on both. Fixes: 69551a244292 ("ramips: manage low reset lines") Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> (cherry picked from commit 680f91d0e5444d58815af03bf41c12592438f9d8)
* kernel: Deactivate CONFIG_VFIO in generic kernel configHauke Mehrtens2021-03-273-2/+1
| | | | | | | | | Instead of deactivating this in every target config, deactivate it once in the generic kernel config. I was asked for this config option in a x86 64 build in OpenWrt 21.02. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 7d6553c72edada262ada8dbe871243c35400573d)
* kernel: bump 5.4 to 5.4.108Hauke Mehrtens2021-03-2760-137/+130
| | | | | | | | | Refreshed all patches. Compile-tested on: x86_64, ath79, lantiq Runtime-tested on: x86_64, ath79 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: Add support for Buffalo WZR-HP-G300NHMauri Sandberg2021-03-276-5/+335
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This device is a wireless router working on 2.4GHz band based on Qualcom/Atheros AR9132 rev 2 SoC and is accompanied by Atheros AR9103 wireless chip and Realtek RTL8366RB/S switches. Due to two different switches being used also two different devices are provided. Specification: - 400 MHz CPU - 64 MB of RAM - 32 MB of FLASH (NOR) - 3x3:2 2.4 GHz 802.11bgn - 5x 10/100/1000 Mbps Ethernet - 4x LED, 3x button, On/Off slider, Auto/On/Off slider - 1x USB 2.0 - bare UART header place on PCB Flash instruction: - NOTE: Pay attention to the switch variant and choose the image to flash accordingly. (dmesg / kernel logs can tell it) - Methods for flashing - Apply factory image in OEM firmware web-gui. - Sysupgrade on top of existing OpenWRT image - U-Boot TFPT recovery for both stock or OpenWRT images: The device U-boot contains a TFTP server that by default has an address 192.168.11.1 (MAC 02:AA:BB:CC:DD:1A). During the boot there is a time window, during which the device allows an image to be uploaded from a client with address 192.168.11.2. The image will be written on flash automatically. 1) Have a computer with static IP address 192.168.11.2 and the router device switched off. 2) Connect the LAN port next to the WAN port in the device and the computer using a network switch. 3) Assign IP 192.168.11.1 the MAC address 02:AA:BB:CC:DD:1A arp -s 192.168.11.1 02:AA:BB:CC:DD:1A 4) Initiate an upload using TFTP image variant curl -T <imagename> tftp://192.168.11.1 5) Switch on the device. The image will be uploaded subsequently. You can keep an eye on the diag light on the device, it should keep on blinking for a while indicating the writing of the image. General notes: - In the stock firmware the MAC address is the same among all interfaces so it is left here that way too. Recovery: - TFTP method - U-boot serial console Differences to ar71xx platform - This device is split in two different targets now due to hardware being a bit different under the hood. Dynamic solution within the same image is left for later time. - GPIOs for a sliding On/Off switch, marked 'Movie engine' on the device cover, were the wrong way around and were renamed qos_on -> movie_off, qos_off -> movie_on. Associated key codes remained the same they were. The device tree source code is mostly based on musashino's work Signed-off-by: Mauri Sandberg <sandberg@mailfence.com> (cherry picked from commit bc356de2850f14629cb1301be719772fa1212e72)
* ath79: cfi: cmdset_0002: amd chip 0x2201 - write wordsMauri Sandberg2021-03-271-0/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | Generally, in upstream CFI flash memory driver uses buffers for write operations. That does not work with AMD chip with id 0x2201 and we must resort to writing word sized chunks only. That is, to not apply general buffer write functionality for this given chip. Without the patch kernel logs will be flooded with entries like below: MTD do_erase_oneblock(): ERASE 0x01fa0000 MTD do_write_buffer(): WRITE 0x01fa0000(0x00001985) MTD do_erase_oneblock(): ERASE 0x01f80000 MTD do_write_buffer(): WRITE 0x01f80000(0x00001985) MTD do_write_buffer_wait(): software timeout, address:0x01f8000a. jffs2: Write clean marker to block at 0x01a60000 failed: -5 MTD do_erase_oneblock(): ERASE 0x01f60000 MTD do_write_buffer(): WRITE 0x01f60000(0x00001985) MTD do_write_buffer_wait(): software timeout, address:0x01f6000a. jffs2: Write clean marker to block at 0x01a40000 failed: -5 References: http://patchwork.ozlabs.org/project/linux-mtd/patch/20210309174859.362060-1-sandberg@mailfence.com/ Signed-off-by: Mauri Sandberg <sandberg@mailfence.com> [added link to usptream fix submission] Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 8cc0fa8faceadac85353bb1a96e074518ef124e2)
* ramips: add support for ELECOM WRC-1750GST2INAGAKI Hiroshi2021-03-222-0/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GST2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 256 MiB (NT5CC128M16JR-EK) - Flash : SPI-NOR 32 MiB (MX25L25645GMI-08G) - WLAN : 2.4/5 GHz 3T3R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LEDs/Keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX, from ethernet port side - 57600n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-1750GST2 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC addresses: LAN : 04:AB:18:xx:xx:23 (Factory, 0xE000 (hex)) WAN : 04:AB:18:xx:xx:24 (Factory, 0xE006 (hex)) 2.4GHz : 04:AB:18:xx:xx:25 (Factory, 0x4 (hex)) 5GHz : 04:AB:18:xx:xx:26 (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (cherry picked from commit b3ca1f30efd7bb96a22f72b766d302e552265276)
* ath79: fix lan port display order for sitecom wlr-7100Walter Sonius2021-03-221-1/+1
| | | | | | | | | | | Physical port order watched from the back of the device is: 4 / 3 / 2 / 1 / WAN which also matches corresponding leds. This patch corrects LuCI switch webpage LAN port order. Signed-off-by: Walter Sonius <walterav1984@gmail.com> [improve commit title, fix sorting in 02_network] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 46c0634b508f731df487a7909c439b2794445e26)
* mvebu: add LED support for GL.iNet GL-MV1000Jeff Collins2021-03-222-1/+46
| | | | | | | | | This patch enables LED support for the GL.iNet GL-MV1000 Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com> [add SPDX identifier on new file, add aliases, minor cosmetic issues] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 6e0c780eb3b4ba1e52216c1d671897749dd81829)
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-30 13:40:02 +0000