aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
...
* bcm63xx: refactor board patchesÁlvaro Fernández Rojas2020-08-0769-1483/+1401
| | | | | | | Current board patches format is crazy. Let's try to put some order. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ramips: switch rt3883 subtarget to kernel 5.4Adrian Schmutzler2020-08-061-2/+0
| | | | | | | | | | | | The target has testing support for kernel 5.4 for quite a while, compiles fine for all devices, and has been run-tested on Asus RT-N56U successfully. Let's set it to kernel 5.4 by default to increase the audience before an 20.xx stable branch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Eneas U de Queiroz <cotequeiroz@gmail.com> [Asus RT-N56U]
* bcm63xx: switch to upstream CFE version detection patchÁlvaro Fernández Rojas2020-08-067-32/+61
| | | | | | The patch improving CFE version detection has been merged (linux 5.9). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: switch to upstream endif comments patchÁlvaro Fernández Rojas2020-08-0686-354/+451
| | | | | | | This allows better context for board patches and we no longer need a downstream patch for that. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bcm63xx: switch to upstream LED patchÁlvaro Fernández Rojas2020-08-061-44/+95
| | | | | | | The patch adding support for the second LED HW blinking interval has been merged (linux 5.9). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* Revert "procd: update to git HEAD"Daniel Golle2020-08-061-2/+16
| | | | | | This reverts commit e0e607f0d000e62c6af8d822d7c3f57c2a582136. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79/nand: add support for Netgear WNDR4300TNDavy Hollevoet2020-08-0610-40/+79
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the WNDR4300TN, marketed by Belgian ISP Telenet. The hardware is the same as the WNDR4300 v1, without the fifth ethernet port (WAN) and the USB port. The circuit board has the traces, but the components are missing. Specifications: * SoC: Atheros AR9344 * RAM: 128 MB * Flash: 128 MB NAND flash * WiFi: Atheros AR9580 (5 GHz) and AR9344 (2.4 GHz) * Ethernet: 4x 1000Base-T * LED: Power, LAN, WiFi 2.4GHz, WiFi 5GHz, WPS * UART: on board, to the right of the RF shield at the top of the board Installation: * Flashing through the OEM web interface: + Connect your computer to the router with an ethernet cable and browse to http://192.168.0.51/ + Log in with the default credentials are admin:password + Browse to Advanced > Administration > Firmware Upgrade in the Telenet interface + Upload the Openwrt firmware: openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img + Proceed with the firmware installation and give the device a few minutes to finish and reboot. * Flashing through TFTP: + Configure your wired client with a static IP in the 192.168.1.x range, e.g. 192.168.1.10 and netmask 255.255.255.0. + Power off the router. + Press and hold the RESET button (the factory reset button on the bottom of the device, with the gray circle around it, next to the Telenet logo) and turn the router on while keeping the button pressed. + The power LED will start flashing orange. You can release the button once it switches to flashing green. + Transfer the image over TFTP: $ tftp 192.168.1.1 -m binary -c put openwrt-ath79-nand-netgear_wndr4300tn-squashfs-factory.img Signed-off-by: Davy Hollevoet <github@natox.be> [use DT label reference for adding LEDs in DTSI files] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear JWNR2010 v5Shibajee Roy2020-08-065-0/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - CPU: MediaTek MT7620N (580 MHz) - Flash size: 4 MB NOR SPI - RAM size: 32 MB DDR1 - Bootloader: U-Boot - Wireless: MT7620N 2x2 MIMO 802.11b/g/n (2.4 GHz) - Switch: MT7620 built-in 10/100 switch with vlan support - Ports: 4x LAN, 1x WAN - Others: 7x LED, Reset button, UART header on PCB (57600 8N1) Flash instructions: 1. Use ethernet cable to connect router with PC/Laptop, any router LAN port will work. 2. To flash openwrt we are using nmrpflash[1]. 3. Flash commands: First we need to identify the correct Ethernet id. nmrpflash -L nmrpflash -i net* -f openwrt-ramips-mt7620-netgear_jwnr2010-v5-squashfs-factory.img This will show something like "Advertising NMRP server on net*..." (net*, *=1,2,3... etc.) 4. Now remove the power cable from router back side and immediately connect it again. You will see flash notification in CMD window, once it says reboot the device just plug off the router and plug in again. Revert to stock: 1. Download the stock firmware from official netgear support[2]. 2. Follow the same nmrpflash procedure like above, this time just use the stock firmware. nmrpflash -i net* -f N300-V1.1.0.54_1.0.1.img MAC addresses on stock firmware: LAN = *:28 (label) WAN = *:29 WLAN = *:28 On flash, the only valid MAC address is found in factory 0x4. Special Note: This openwrt firmware will also support other netgear N300 routers like below as they share same stock firmware[3]. JNR1010v2 / WNR614 / WNR618 / JWNR2000v5 / WNR2020 / WNR1000v4 / WNR2020v2 / WNR2050 [1] https://github.com/jclehner/nmrpflash [2] https://www.netgear.com/support/product/JWNR2010v5.aspx [3] http://kb.netgear.com/000059663 Signed-off-by: Shibajee Roy <ador250@protonmail.com> [create DTSI, use netgear_sercomm_nor, disable by default, add MAC addresses to commit message, add label MAC address] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: drop remaining m25p,chunked-io from DTSAdrian Schmutzler2020-08-063-3/+0
| | | | | | | | | | | | | | This option was a spi nor hack which is dropped in commit bcf4a5f474d1 ("ramips: remove chunked-io patch and set spi->max_transfer_size instead") Most of it has already been removed in be2b61e4f1ec ("ramips: drop m25p,chunked-io from dts") It seems all current usages were added after that. Remove them. Cc: Chuanhong Guo <gch981213@gmail.com> Reported-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add common definition netgear_sercomm_norAdrian Schmutzler2020-08-063-27/+24
| | | | | | | | Like NAND-based devices, SPI-NOR based Netgear devices also share a common setup for their images. This creates a common defition for them in image/Makefile, so it can be reused across subtargets. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* procd: update to git HEADDaniel Golle2020-08-061-16/+2
| | | | | | | | | | | 47a9f0d service: add method to query available container features afbaba9 initd: attempt to mount cgroup2 ead60fe jail: use pidns semantics also for timens 759e9f8 jail: make use of BLOBMSG_CAST_INT64 for OCI rlimits 83053b6 instance: add instances into unified cgroup hierarchy 16159bb jail: parse OCI cgroups resources Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: tidy up MAC address setup for Linkit Smart and Omega2Adrian Schmutzler2020-08-063-8/+2
| | | | | | | | | | | | | | | | | | | | Linkit Smart 7688 and Onion Omega 2(+) are one-port devices, and have their port set to LAN by default. Setting up a WAN MAC address for them doesn't make any sense, as no wan interface will be created in uci config. Despite, these devices also set lan_mac in 02_network, although mtd-mac-address sets a different address for the ethernet interface in DTS. Clean this up by moving the lan_mac value into DTS and dropping the entries in 02_network completely. That way, the effective address on the LAN interface should stay the same, but we get rid of the extra (re)assignments. As I don't have access to the devices, this does not tell anything about whether 0x2e is actually a good choice, it just preserves the existing assignment. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: WizFi630S use macs from factory partionTobias Welz2020-08-062-3/+6
| | | | | | | | | | | | | | | | | | | | WIZnet WizFi630s has three mac addresses in the factory partition: 0x04 (also on the label), 0x28 for wan mac and 0x2e as lan mac. All three macadresses are sequential series of addresses. This is making use of them. While at it, also add the label MAC address to 02_network. MAC addresses as verified by OEM firmware: use interface source WLAN ra0 factory 0x04 (label) WAN eth0.2 factory 0x28 (label + 1) LAN eth0.1 factory 0x2e (label + 2) Signed-off-by: Tobias Welz <tw@wiznet.eu> [fix sorting in 02_network, commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: correct WizFi630S pin mappingsTobias Welz2020-08-061-26/+8
| | | | | | | | | | WizFi630S had some pins changed in the release version of the board. The run led, wps button and a slide switch where affected. This patch is correcting this. i2c is removed as it is sharing a pin with the run (system) led. uart2 is enabled as it is also enabled in the OEM firmware. Signed-off-by: Tobias Welz <tw@wiznet.eu>
* ipq40xx: refresh kernel 5.4 configAdrian Schmutzler2020-08-061-11/+3
| | | | | | | | | | | Refresh config with make kernel_oldconfig. After d1a8217d87bf ("kernel: clean-up build-configurable kernel config symbols"), the routine wants to add an additional CONFIG_CGROUPS (=n), which has been removed manually again, as this seems unintended. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: fix mt7622-rfb1 board supportFelix Fietkau2020-08-066-60/+67
| | | | | | | Make GPIO keys active-low. Add DSA support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-0667-67/+3
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: switch rt305x subtarget to kernel 5.4Alexey Dobrovolsky2020-08-056-6/+5
| | | | | | | | | | | | | | RT3x5x seems to work fine with kernel 5.4. Set the default kernel version to 5.4 to bring this to a broader audience. Since 4 of 6 targets are on kernel 5.4 now, invert the kernel version setup logic in Makefile/target.mk files. Tested on ZyXEL Keenetic. Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com> [invert version setup logic] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: enable flashing WizFi630S via OEM firmwareTobias Welz2020-08-051-0/+1
| | | | | | | | | | | WIZnet WizFi630s board name is written slightly different it its OEM OpenWrt firmware. This causes an incompatibility warning during flashing with sysupgrade. This patch is adding the vendor board name to the supported devices list to avoid this warning. For initial flashing you can use sysupgrade via command line or luci beside of TFTP. Do not keep the OEM configuration during sysupgrade. Signed-off-by: Tobias Welz <tw@wiznet.eu>
* ipq806x: use qcom-ipq8064-v1.0.dtsi from upstreamAdrian Schmutzler2020-08-058-222/+186
| | | | | | | | | | | | | | | | | This uses upstream qcom-ipq8064-v1.0.dtsi and modifies it by patches instead of keeping a local version. As a consequence: - we use a part of the shared definitions there and update device DTS files accordingly - we move additional stuff from our local v1.0.dtsi to the patch - we drop partitions, LEDs and keys from the file as we will implement them differently anyway Like with the previous patch, this follows the idea that a diff from upstream might be easier to handle than a big file of our own with different distribution pattern of properties. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: use qcom-ipq8064.dtsi from upstreamAdrian Schmutzler2020-08-058-1579/+1164
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Though a qcom-ipq8064.dtsi file exists upstream, we still do overwrite it with a full version of our own in the ipq806x target. About half of the contents of our file are upstream content, the other half are local improvements. To prevent us from having a lot of code maintained twice in parallel, this adjusts the target to use the upstream qcom-ipq8064.dtsi. Our local changes are arranged into three patches, the first pulling a commit from upstream, the second doing a few small adjustments, and the third adding all additional stuff. This should get us the best of both worlds. The property "ports-implemented" on sata@29000000 is moved to 2nd-level DTSI files as kernel defines it there as well. While at, rename 080-ARM-dts-qcom-add-gpio-ranges-property.patch to include the kernel version where it's added upstream. Even though this might look more complicated in the first place, the aim is to bring our files closer to upstream, so we can benefit from changes directly and vice-versa. After all, this drop about 650 lines just copied from the upstream DTSI file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove doublet entry in WizFi630S dts fileTobias Welz2020-08-051-4/+0
| | | | | | | &wmac entry in WIZnet WizFi630S dts file was existing two times. This is removing one of them. Signed-off-by: Tobias Welz <tw@wiznet.eu>
* ramips: disable unused phy ports of WizFi630STobias Welz2020-08-051-0/+1
| | | | | | | WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports draw unnecessarily power. This is disabling the unused phy ports. Signed-off-by: Tobias Welz <tw@wiznet.eu>
* bcm47xx: switch to kernel 5.4Rafał Miłecki2020-08-041-1/+1
| | | | | | Switch, LEDs, USB, buttons, sysupgrade testedon BCM4706. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: switch to kernel 5.4Rafał Miłecki2020-08-041-1/+1
| | | | | | Switch, USB, WiFi, buttons tested on BCM47094. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: set HW_RANDOM_BCM2835=yRafał Miłecki2020-08-041-0/+2
| | | | | | | | | | This enables Random Number Generator support on Northstar (described in DT with brcm,bcm5301x-rng). It's also a workaround for OpenWrt bug with kernel config causing: Broadcom BCM2835/BCM63xx Random Number Generator support (HW_RANDOM_BCM2835) [Y/n/m/?] (NEW) Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: update kernel 5.4 DTS to upstream 5.9 stateRafał Miłecki2020-08-043-0/+333
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: update kernel 5.4 configRafał Miłecki2020-08-041-100/+4
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for TP-Link RE200 v3Richard Fröhning2020-08-034-0/+82
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE200 v3 is a wireless range extender with Ethernet and 2.4G and 5G WiFi with internal antennas. It's based on MediaTek MT7628AN+MT7610EN like the v2. Specifications -------------- - MediaTek MT7628AN (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 1x 10/100 Mbps Ethernet - 8x LED (GPIO-controlled), 2x button Unverified: - UART header on PCB (57600 8n1) There are 2.4G and 5G LEDs in red and green which are controlled separately. MAC addresses ------------- MAC address assignment has been done according to the RE200 v2. The label MAC address matches the OpenWrt ethernet address. Installation ------------ Web Interface ------------- It is possible to upgrade to OpenWrt via the web interface. Simply flash the -factory.bin from OEM. In contrast to a stock firmware, this will not overwrite U-Boot. Recovery -------- Unfortunately, this devices does not offer a recovery mode or a tftp installation method. If the web interface upgrade fails, you have to open your device and attach serial console. The device has not been opened for adding support. However, it is expected that the behavior is similar to the RE200 v2. Instructions for serial console and recovery may be checked out in commit 6d6f36ae787c ("ramips: add support for TP-Link RE200 v2") or on the device's Wiki page. Signed-off-by: Richard Fröhning <misanthropos@gmx.de> [adjust commit title/message, sort support list] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix/tidy up 4M tplink-v2-image flash layoutsAdrian Schmutzler2020-08-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | For the TP-Link 4M devices with tplink-v2-image recipe (mktplinkfw2.c), there are two different flash layouts based on the size of the (u)boot partition: device uboot OEM firmware OpenWrt (incl. config) tl-wr840n-v5 0x20000 0x3c0000 0x3d0000 tl-wr841n-v14 0x10000 0x3d0000 0x3e0000 In both cases, the 0x10000 config partition is used for the firmware partition as well due to the limited space available and since it's recreated by the OEM firmware anyway. However, the TFTP flashing process will only copy data up to the size of the initial (OEM) firmware size. Therefore, while we can use the bigger partition to have additional erase blocks on the device, we have to limit the image sizes to the TFTP limits. So far, only one layout definition has been set up in mktplinkfw2.c for 4M mediatek devices. This adds a second one and assigns them to the devices so the image sizes are correctly restrained. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: get rid of BOARD_NAME and tidy up DEVICE_DTSAdrian Schmutzler2020-08-031-16/+14
| | | | | | | | | | | Since most of the DTS file names follow a common scheme now, let's update the automatically generated DEVICE_DTS value and get rid of some DEVICE_DTS and all BOARD_NAME entries for individual devices. This should specifically make the job easier for developers adding new devices, as they are not tempted to copy over BOARD_NAME anymore. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* target: replace remaining occurrences of ifconfig with ipAdrian Schmutzler2020-08-035-8/+9
| | | | | | | | | | | ifconfig is effectively deprecated for quite some time now. Let's replace the remaining occurrences for our target setup by the corresponding ip commands now. Note that this does not touch ar71xx, as it will be dropped anyway, and changing it would only make backports harder. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: restore support for boot console with arbitrary baud ratesSungbo Eo2020-08-021-0/+54
| | | | | | | | | | | Commit 1bfbf2de6df9 ("ar71xx: serial: core: add support for boot console with arbitrary baud rates") added support for arbitrary baud rates which enabled 250000 baud rate for Yun. But the patch was not ported to kernel 4.9, and since then the kernel set its baud rate to 9600. This commit ports the patch to kernel 4.14, thereby restoring the serial console of Yun. Cc: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ar71xx: enable ethernet LED of Arduino YunSungbo Eo2020-08-021-2/+1
| | | | | | | | Commit 05d73a2a7379 enabled GPIO on ethernet LED, but proper LED setup was not added then. This commit fixes it by reverting the change on the LED. Fixes: 05d73a2a7379 ("ar71xx: Arduino Yun board 'WLAN RST' button support") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ar71xx: fix sysupgrade for Arduino YunSungbo Eo2020-08-021-1/+1
| | | | | | | | | Commit bb46b635df48 changed its partition scheme, but sysupgrade image validation still uses the old format. This commit fixes it so that force flag is not needed for sysupgrade. Fixes: bb46b635df48 ("ar71xx: move Arduino Yun to generic building code") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* Revert "ar71xx: fix Arduino Yun enabling of level shifters outputs"Sungbo Eo2020-08-021-2/+2
| | | | | | | | | This reverts commit 077253dd666a30ae5231c3748222d4b5b138593d. The output enable pins should be disabled by default, and only enabled when used. Otherwise unwanted conflicts might occur between MCU and SoC pins. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ath79/mikrotik: create shared device definitions for nor and nandAdrian Schmutzler2020-08-012-13/+19
| | | | | | | Move the image preparation and nand-utils package selection into common device definitions for NOR/NAND devices. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: fix missing TRANSPARENT_HUGEPAGE symbolsStijn Tintel2020-08-011-0/+1
| | | | | | | | | | | | | | | | Enabling KERNEL_TRANSPARENT_HUGEPAGE exposes 2 missing symbols: * CONFIG_READ_ONLY_THP_FOR_FS * TRANSPARENT_HUGEPAGE_ALWAYS * TRANSPARENT_HUGEPAGE_MADVISE The first one was added in 5.4, and is marked experimental there so just disable it in the generic config. For the latter two, we should not force the user to use either of them, so add them as build-configurable kernel options. Fixes: d1a8217d87bf ("kernel: clean-up build-configurable kernel config symbols") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add missing config symbolStijn Tintel2020-08-013-0/+3
| | | | | | | | | | This symbol is exposed on ARM64 with EFI enabled in the kernel config. Currently this happens only on ipq807x, but as there might be new ARM64 targets with EFI in the future it is better to add the symbol to the generic config. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Jo-Philipp Wich <jo@mein.io>
* gemini: Add swap partition to DNS-313Linus Walleij2020-07-311-7/+13
| | | | | | | | | Sometimes when using the DNS-313 memory usage can peak and with a simple swap partition we can avoid running into the roof and invoking the OOM killer. Set this partition to 128MB (twice the size of the memory of the DNS-313). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* apm821xx: disable WNDR4700 5.4 imageChristian Lamparter2020-07-311-0/+1
| | | | | | | | | | | | | | | The compressed image that the buildbots are building is too large for the netgear uboot and it crashes and soft-bricks the device. | Uncompressing Kernel Image ... | LZMA: uncompress or overwrite error 1 - must RESET board to recover The whole target likely needs to be switched zImage which is a major hassle due to powerpc's legacy bootwrapper setup as compared to ARM. So for now, disable the device. Reported-by: Wiktor Stasiak (FS#3258) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kirkwood: use real model names for Linksys devicesAdrian Schmutzler2020-07-3110-29/+63
| | | | | | | | | | | | This replaces the internal device names "Audi" and "Viper" with the real model names, which a user would look for. This makes the Linksys devices on this target consistent with the names recently changed for mvebu based on the same idea. As a consequence, the "viper" device definition is split into two separate definitions with the correct names for both real models. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: mips: restore missing MIPS32 cBPF JITTony Ambardar2020-07-311-0/+1663
| | | | | | | | | | | | | | | | | | | Kernel v5.1 included an eBPF JIT for MIPS32 kernels, but problems were discovered [1] and the changes later reverted in kernel v5.5 with commits: * f8fffebdea75 ("MIPS: BPF: Disable MIPS32 eBPF JIT") * 36366e367ee9 ("MIPS: BPF: Restore MIPS32 cBPF JIT") Only the first of these was backported to LTS kernel 5.4, leaving cBPF programs without a JIT and introducing a performance regression for any such users e.g. libpcap, tcpdump, etc. Restore cBPF performance by backporting the second commit above: * 070-v5.5-MIPS-BPF-Restore-MIPS32-cBPF-JIT.patch [1] https://lore.kernel.org/bpf/20191205182318.2761605-1-paulburton@kernel.org/ Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* mvebu: fix alphabetic sorting in 02_networkAdrian Schmutzler2020-07-311-6/+6
| | | | | | This has been overlooked when removing solidrun,clearfog-a1 entry. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: increase compat version for SolidRun ClearFog BaseAdrian Schmutzler2020-07-312-1/+4
| | | | | | | | | | | | | When changing the Pro variant to DSA, the ethernet interface rename script was dropped by all devices to keep them in sync: be309bfd7445 ("mvebu: drop 06_set_iface_mac preinit script") Therefore, network config will be broken after upgrade for the Base variant as well. Increase the compat version and provide a message to signal that to the users. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: implement compatibility version for DSA migrationAdrian Schmutzler2020-07-312-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for kirkwood. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Since we never removed SUPPORTED_DEVICES for this target, we don't have to add it back either. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mvebu: implement compatibility version for DSA migrationAdrian Schmutzler2020-07-312-0/+44
| | | | | | | | | | | | | | | | | | | | | | | | | | This implements the newly introduced compat-version to prevent upgrade between swconfig and DSA for mvebu. Just define a compat version with minor increment and an appropriate message for both image (in Makefile) and device (in base-files). Having taken care of sysupgrade, we can put back the SUPPORTED_DEVICES that have been removed in previous patches to prevent broken config. Attention: All users that already updated to the DSA versions in master will receive the same incompatibility warning since their devices are still "1.0" as far as fwtool can tell. Those, and only those, can bypass the upgrade check by using force (-F) without having to reset config again. In addition, the new version string needs to be put into uci config manually, so the new fwtool knows that it actually deals with a "1.1": uci set "system.@system[-1].compat_version=1.1" uci commit system Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for JS76x8 series DEV boardsRobinson Wu2020-07-316-4/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Jotale JS76x8 series development boards. These devices have the following specifications: - SOC: MT7628AN/NN, MT7688AN, MT7628DAN - RAM of MT7628AN/NN and MT7688AN: 64/128/256 MB (DDR2) - RAM of MT7628DAN: 64 MB (DDR2) - FLASH:8/16/32 MB (SPI NOR) - Ethernet:3x 10/100 Mbps ethernet ports (MT76x8 built-in switch) - WIFI:1x 2T2R 2.4 GHz Wi-Fi - LEDs:1x system status green LED, 1x wifi green LED, 3x ethernet green LED - Buttons:1x reset button - 1x microSD slot - 4x USB 2.0 port - 1x mini-usb debug UART - 1x DC jack for main power (DC 5V) - 1x TTL/RS232 UART - 1x TTL/RS485 UART - 13x GPIO header - 1x audio codec(wm8960) Installation via OpenWrt: The original firmware is OpenWrt, so both LuCI and sysupgrade can be used. Installation via U-boot web: 1. Power on board with reset button pressed, release it after wifi led start blinking. 2. Setup static IP 192.168.1.123/4 on your PC. 3. Go to 192.168.1.8 in browser and upload "sysupgrade" image. Installation via U-boot tftp: 1. Connect to serial console at the mini usb, which has been connected to UART0 on board (115200 8N1) 2. Setup static IP 192.168.1.123/4 on your PC. 3. Place openwrt-firmware.bin on your PC tftp server (192.168.1.123). 3. Connect one of LAN ports on board to your PC. 4. Start terminal software (e.g. screen /dev/ttyUSB0 115200) on PC. 5. Apply power to board. 6. Interrupt U-boot with keypress of "2". 7. At u-boot prompts: Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y Input device IP (192.168.1.8) ==:192.168.1.8 Input server IP (192.168.1.123) ==:192.168.1.123 Input Linux Kernel filename (root_uImage) ==:openwrt-firmware.bin 8. board will download file from tftp server, write it to flash and reboot. Signed-off-by: Robinson Wu <wurobinson@qq.com> [add license to DTS files, fix state_default and reduce to the mimimum, move phy0tpt trigger to DTS, drop ucidef_set_led_timer, fix network ports] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: limit 5GHz channels for RAVPower RP-WD009David Bauer2020-07-301-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | When selecting a channel below 100 on the 5GHz radio, the channel will be detected as busy all the time. Survey data from wlan1 frequency: 5240 MHz [in use] channel active time: 165729 ms channel busy time: 158704 ms channel transmit time: 0 ms Channels 100 and above work fine: Survey data from wlan1 frequency: 5500 MHz channel active time: 133000 ms channel busy time: 21090 ms channel transmit time: 0 ms Limit the available channels, so users do not have the impression their device is broken. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: mark devices as BROKEN instead of commenting outPetr Štetiar2020-07-302-7/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | This adds the newly introduced BROKEN flag to a bunch of devices that previously just had TARGET_DEVICES commented out. By this, we can select them in make menuconfig when BROKEN developer config option is selected, instead of having to edit the code. In contrast to DEFAULT := n, this is meant to cover devices that don't boot or don't compile at all. ath25: np25g, wpe53g both disabled during kernel bump 3.18->4.4 without reason given f89a20a89aeb ("ath25: update kernel from 3.18 to 4.4") bcm53xx: linksys-ea6300-v1, linksys-ea9200, linksys-ea9500 broken due to insufficient/broken TRX support 55ff15cfd509 ("bcm53xx: disable building Linksys EA6300 V1 image") cd0f9900a4cd ("bcm53xx: parepare for building more Linksys images") bcm63xx: tplink-archer-c5-v2, tplink-archer-c9-v1 disabled when kernel 5.4 support was added, probably broken 50c6938b95a0 ("bcm53xx: add v5.4 support") Signed-off-by: Petr Štetiar <ynezz@true.cz> [limit to subset of devices, use BROKEN, adjust commit message/title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-06 07:04:24 +0000