aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* brcm2708: Add wifi driver, firmware and NVRAM for RPi1Daniel Golle2018-06-201-0/+1
| | | | | | | | Apparently there are RPi1 devices with BRCM43430 wifi, such as the Pi Zero W. Add the necessary packages for that to the image generated for those boards as well. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: ar934x: use irq-ath79-intc driver and enable wmacJohann Neuhauser2018-06-204-9/+66
| | | | Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: qca95xx: add new intc2, correct intc3 and add second pcie on qca9557Johann Neuhauser2018-06-203-9/+49
| | | | Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: fix irq-ath79-intc driver and add support for other ath79 SoCsJohann Neuhauser2018-06-201-14/+52
| | | | | | | | | | | | | | Add the missing enable and disable function. Remove dummy mask and unmask function and use the one provided by irq_dummy_chip. Allow interrupt status register being defined from dts. Add ddr_wb_flush for ar934x/qca953x. Rename controller name to qca,ar9340-intc because this design was first introduced in AR934x. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ramips: add support for ELECOM WRC-1167GHBK2-SINAGAKI Hiroshi2018-06-196-4/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - MT7621A (2-Cores, 4-Threads) - 128 MB of RAM (DDR3) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz - MediaTek MT7615D - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 2x keys - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 57600 bps Flash instruction using factory image: 1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin" 2. Connect the computer to the LAN port of WRC-1167GHBK2-S 3. Connect power cable to WRC-1167GHBK2-S and turn on it 4. Access to "http://192.168.2.1/details.html" and open firmware update page ("手動更新（アップデート）") 5. Select the factory image and click apply ("適用") button 6. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-199-7/+484
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mt7621: fix wireless package selectionMathias Kresin2018-06-191-5/+4
| | | | | | | Add wpad-mini if wireless drivers are included. Drop the mt76 package if both of the provided drivers are included with their own packages. Signed-off-by: Mathias Kresin <dev@kresin.me>
* arc770: bump kernel to 4.14Evgeniy Didin2018-06-193-23/+26
| | | | | | | | | | Currently arc770 is no more "source-only". Lets update Linux kernel version from 4.9 to 4.14 for arc770. config-4.14 was simply regenerated with "make kernel_menuconfig". Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: John Crispin <john@phrozen.org>
* ar71x: add support for Mikrotik Routerboard wAP RDavid Ehrmann2018-06-198-4/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change is based on 3b15eb0 which added support for the wAP 2nD. This change lacks LED support. Specifications: - SoC: Qualcomm QCA9531 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: built-in QCA9531, 802.11b/g/n 2x2:2 - Ethernet: 1x100Mbps - Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack - SIM card slot - Mini-PCIe slot Installation: 1. Login to the Mikrotik WebUI to backup your licence key 2. Change the following settings in System->Routerboard->Settings: - Boot device: try ethernet once then NAND - Boot protocol: DHCP - Force Backup Booter: checked 3. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image, e.g. openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf 4. Power off the device 5. If this is the second attempt to boot OpenWRT or the boot device isn't "try ethernet once then NAND," press and hold the reset button while powered off. If this is the first attempt, this step isn't necessary. 6. Power on the device, holding the reset button for 15-20s if already pressed from the previous step. The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started OpenWRT via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT. Revert to RouterOS Use the "rbcfg" package on in OpenWRT: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: David Ehrmann <ehrmann@gmail.com>
* ramips: improve ethernet driver performance with GRO/TSOFelix Fietkau2018-06-193-76/+105
| | | | | | | | | | | GRO stores packets as fraglist. If they are routed back to the ethernet device, they need to be re-segmented if the driver does not support sending fraglists. Add the missing support for that, along with a missing feature flag that allows full routed GRO->TSO offload. Considerably reduces CPU utilization for routing Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: fix qm5p-ac-v2 dts fileJohn Crispin2018-06-181-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: add support for Fritz!WLAN Repeater 450EDavid Bauer2018-06-1813-1/+212
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!WLAN Repeater 450E SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4GHz WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - Most LEDs Not working: - 2 RSSI LEDs AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they control over MDIO. Our driver doesn't expose these LEDs as GPIOs. While it is possible to implement this feature, it would require an additional kernel patch for a minor functionality. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. You need to powercycle the Device afterwards to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: fix incorrect speed setting on QCA9556David Bauer2018-06-181-3/+17
| | | | | | | | | The QCA9556 only has a SGMII interface. However the speed on the ethernet link is set for the non-existant xMII interface. This commit fixes this behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for tl-wr1043nd v2/v3Lucian Cristian2018-06-186-23/+341
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add initial nand support for gl-ar300mMarty E. Plummer2018-06-187-1/+123
| | | | Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
* ath79: initial gl-ar300m supportMarty E. Plummer2018-06-185-0/+436
| | | | Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
* mvebu: enable CONFIG_HW_RANDOMHannu Nyman2018-06-181-0/+1
| | | | | | | | | Enable the Hardware Random Number Generator Core infrastructure in kernel. Needed for hardware random number generator drivers like chaoskey Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ipq806x: D7800 only has a single sata portJohn Crispin2018-06-181-0/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mips: fix dynamic ftraceVincent Wiemann2018-06-181-3/+8
| | | | | | | | | | The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as dynamic ftrace depends on -mlong-calls. See http://patchwork.linux-mips.org/patch/675/ Thus we always set -mlong-calls if the kernel is being compiled with dynamic ftrace support. Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
* mvebu: backport ahci_mvebu errata patchsetJeremiah McConnell2018-06-182-0/+334
| | | | | | | | | | | | Marvell ahci hardware requires a workaround to prevent eSATA failures on hotplug/reset when used with multi-bay external enclosures. Errata Ref#226 - SATA Disk HOT swap issue when connected through Port Multiplier in FIS-based Switching mode. These patches backport the workaround from 4.17. Signed-off-by: Jeremiah McConnell <miah@miah.com>
* ath79: fix rx ring buffer stall qca956xLucian Cristian2018-06-181-1/+2
| | | | | | when ported from ar71xx to ath79 the qca9560-eth was omitted Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ar71xx: add kmod-usb-ehci to fix USB on RB hAP ACThomas Nixon2018-06-181-1/+1
| | | | Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* ipq40xx: add support for ZyXEL WRE6606Magnus Frühling2018-06-187-2/+300
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
* ath79: add tl-wr1043nd-v4 support everything is workingLucian Cristian2018-06-185-11/+271
| | | | | | | tplink-safeloader: resize kernel partition kernel 4.14 is much bigger, resize the partition Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add ubiquiti unifi ap ac lite/lrLucian Cristian2018-06-184-0/+171
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: ag71xx: fix pll-data setting for ar7242/ar934x/qca955x/qca956xWeijie Gao2018-06-181-10/+7
| | | | | | | | | | | ar71xx/ar913x series use the old pll registers and settings. However started from ar7242, a new pll register is introduced and the pll setting is much simpler. This can be observed from dev-eth.c from the ar71xx target. Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ath79: add support for Phicomm K2TWeijie Gao2018-06-187-0/+587
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds dts for qca956x and also support for Phicomm K2T The qca965x.dtsi adds nearly all the necessary components. Both ath9k AHB and PCIe worked well. The Phicomm K2T uses MTD partition 'config' to store the mac addresses in JSON format. To extract these fields correctly, a script is introduced: /lib/functions/k2t.sh This script provides a helper function to extract mac addresses, and is used in three places. Hardware spec of Phicomm K2T: CPU: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337 WiFi 5.8GHz: QCA9886 Flash instruction: Apply sysupgrade.bin via serial console: tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ipq40xx: essedma: fixup ip alignChen Minqiang2018-06-181-0/+26
| | | | | | | | This fixup ip align in essedma driver rx path see cat /proc/cpu/alignment which reports alignment-fixups without this fix. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* kernel: atm: pppoatm fix vc-mux connection failuresKevin Darbyshire-Bryant2018-06-181-0/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Backport a hot off the press upstream kernel ATM fix: Preserve value of skb->truesize when accounting to vcc "There's a hack in pskb_expand_head() to avoid adjusting skb->truesize for certain skbs. Ideally it would cover ATM too. It doesn't. Just stashing the accounted value and using it in atm_raw_pop() is probably the easiest way to cope." The issue was exposed by upstream with: commit 14afee4b6092fde451ee17604e5f5c89da33e71e Author: Reshetova, Elena <elena.reshetova@intel.com> Date: Fri Jun 30 13:08:00 2017 +0300 net: convert sock.sk_wmem_alloc from atomic_t to refcount_t But an earlier commit left the ticking timebomb: 158f323b9868 ("net: adjust skb->truesize in pskb_expand_head() Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging assistance and to David Woodhouse <dwmw2@infradead.org> for further guidance, cajoling & patience in interpreting the debug I was giving him and producing a fix! Fixes FS#1567 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* lantiq: atm: fix ifx_atm driver integrationKevin Darbyshire-Bryant2018-06-181-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When upstream kernel introduced commit c55fa3cccbc2c672e7f118be8f7484e53a8e9e77 we incorrectly updated our hack integration patch that updates atm/common.c +++ b/net/atm/common.c @@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc write_unlock_irq(&vcc_sklist_lock); } +struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL; +EXPORT_SYMBOL(ifx_atm_alloc_tx); + static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size) { struct sock *sk = sk_atm(vcc); + if (ifx_atm_alloc_tx != NULL) + return ifx_atm_alloc_tx(vcc, size) The correct solution is to drop our ifx_atm_alloc_tx replacement hack entirely and let the kernel do its thing. In reality neither pppoatm or BR2684 interfaces actually hit this code, so the incorrect integration would only be noticed with direct socket calls which we are unaware of a use-case. This is not the solution to pppoatm vc-mux failing to work which started the whole investigation, but let's fix it up anyway. With sincerest thanks to David Woodhouse <dwmw2@infradead.org> & Mathias Kresin <dev@kresin.me>. Tested-on: lantiq, BT HomeHub 5a Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 4.9 to 4.9.109Koen Vandeputte2018-06-182-4/+4
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* bcm53xx: exit if writing kernel during sysupgrade failsRafał Miłecki2018-06-181-2/+2
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: drop not ready support for Luxul devicesRafał Miłecki2018-06-181-30/+0
| | | | | | | | Support for these devices isn't ready yet and it was only accidentally pushed in the commit 0da9303e5b44 ("mac80211: backport "brcmfmac: cleanup and some rework" from 4.17"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mvebu: replace espressobin spi patch with upstream oneTomasz Maciej Nowak2018-06-182-29/+45
| | | | | | | | | For easier future kernel bumps replace spi patch with upstream version slightly modified. The modification removes partition definitions which has been diffrent for some U-Boot versions. Also this removes unnecessary i2c definition which was in the old patch. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: reduce speed to gen1 for espressobin pcieTomasz Maciej Nowak2018-06-182-0/+116
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the beginning there's been an issue with initializing the Atheros based MiniPCIe wireless cards. Here's an example of kerenel log: OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit] pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref] [...] advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k 0000:00:00.0: enabling device (0000 -> 0002) advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40 ath9k 0000:00:00.0: request_irq failed advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k: probe of 0000:00:00.0 failed with error -22 The same happens for ath5k cards, while ath10k card didn't appear at all (not detected): OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link never came up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) advk-pcie d0070000.pcie: config read/write timed out Following the issue on esppressobin.net forum [1] the workaround seems to be limiting the speed of PCIe bridge to 1st generation. This fixed the initialisation of all tested Atheros wireless cards. The change shouldn't affect the performance for wireless cards, it could reduce the performance of storage controller cards but since OpenWrt focuses on wireless connectivity, fixing compatibility with wireless cards should be a priority. For the record, the iwlwifi and mt76 cards were not affected by this issue. 1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: add fix for armada 37xx cpufreq driverTomasz Maciej Nowak2018-06-181-0/+35
| | | | | | Backport from stable kernel tree fixing clock leak. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mediatek: mt7622: Do not deactivate CONFIG_BLK_DEVHauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | zram.ko needs CONFIG_BLK_DEV activated and it is by default for all other targets in OpenWrt. This makes zram.ko compile again. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: mt7622: Do not set CPU_SUBTYPE for Cortex A53Hauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | | | Neon and vfpv4 are mandatory extensions in the ARM64 instruction set now, do not activate them explicitly. GCC will make use of these extension now by default. This makes it possible to share the toolchain with other Cortex A53 SoCs. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ath79: move Netgear build code into a common makefileZoltan HERPAI2018-06-182-23/+23
| | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* kernel: bump 4.14 to 4.14.49Koen Vandeputte2018-06-187-21/+16
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86-64 Runtime-tested on: cns3xxx, imx6, x86-64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.108Koen Vandeputte2018-06-185-167/+189
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: add get_status_led to diag.shDavid Bauer2018-06-181-0/+4
| | | | | | | | | | | This commit adds the get_status_led method to diag.sh, which sets the boot-led as status-led for scripts using this method to get a status-led. This method is used platform-independent in downstream project gluon to set the LED used to indicate the config-mode. Signed-off-by: David Bauer <mail@david-bauer.net>
* gemini: Cook SQ201 imagesLinus Walleij2018-06-182-0/+35
| | | | | | | | | This generates the "rd.gz" and "hddapp.tgz" that doesn't contain anything of the sort but rather the OpenWRT rootfs. It works the same way as how we generate the same layout for the NAS4220b. For some reason the ImageInfo file is different for the SQ201. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gemini: Add appropriate Wireless kernel modulesLinus Walleij2018-06-181-2/+3
| | | | | | | | | | | | The D-Link DIR-685 has a RealTek RT2880 mini-PCI card in a slot. Activate the appropriate kernel module. The Square One SQ201 has a Ralink RT61-based mini-PCI card. Activate the appropriate kernel modules. This fixes the previous error just activating the firmware: the kernel module will bring in the firmware it needs. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gemini: Cook a WRGG firmware imageLinus Walleij2018-06-181-2/+10
| | | | | | | | | This makes the Gemini build a WRGG-type firmware update image for the DIR-685. This should hopefully install the kernel from the web firmware upgrade API on the product switching it permanently to use OpenWRT. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* mac80211: backport "brcmfmac: cleanup and some rework" from 4.17Rafał Miłecki2018-06-171-0/+30
| | | | | | | | | | | It was described by Arend as: > This series is intended for 4.17 and includes following: > > * rework bus layer attach code. > * remove duplicate variable declaration. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: fix NAND partitions on D-Link DIR-885LRafał Miłecki2018-06-171-0/+39
| | | | | | | | | | This fixes missing rootfs on above device: [ 2.652292] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 (...) [ 2.687909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) Fixes: 05cb6aa69f66 ("bcm53xx: replace linux,part-probe with a proper partitions subnode") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: clean up led config script files for all devicesJohann Neuhauser2018-06-167-34/+17
| | | | | | | | | 1. Move all status led definitions out of diag.sh into device dt as we use here a generic script hook. 2. Encode "phy0ptp" led trigger in dt of device for all ath79 devices. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: fix WNDR3800 supportHannu Nyman2018-06-161-12/+37
| | | | | | | | | | | | | | | | Fixes for WNDR3800 DTS: * fix bootcmd * name art partition to reference it for MACs * format firmware partition's address similarly as others * make u-boot-env read-only like in ar71xx * read wan and lan MACs from art * fix LED and button gpio values to match ar71xx (orange/green powerLED, reset button) * enable power LED in dts by alias led-status * define USB LED triggers and connect to USB port * change wifi button to KEY_RFKILL like in ar71xx Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: led-resets: add default-trigger propertyJohann Neuhauser2018-06-161-1/+4
| | | | | | | | | Add support for the common led property "linux,default-trigger". It allows to set a default led trigger via devicetree. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de> [add commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 17:11:02 +0000