aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* kernel: rtl8367b: drop redundant compatibleMathias Kresin2018-06-251-1/+0
| | | | | | | Remove the compatible without vendor prefix. It is formal wrong and not used in the tree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: Add support for TP-Link CPE210 v2Adrian Schmutzler2018-06-236-11/+101
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Notes: TP-Link does not use bootstrap registers so without this patch reference clock detects as 40MHz while it is actually 25MHz. This is due to messed up bootstrap resistor configuration on the PCB. Provided GPL code just forces 25MHz reference clock. That causes booting with completely wrong clocks, for example, CPU tries to boot at 1040MHz while the stock is 650MHz. So this PR depends on PR #672 to remove 40MHz reference clock. Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ar71xx: Add TP-Link Pharos v2 board detectionAdrian Schmutzler2018-06-232-14/+33
| | | | | | | | | | Add support for detecting TP-Link Pharos v2 boards. They use different format in product-info partition than v1 boards. Code was written mostly by Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Re-enable arbitrary IPv6 addresses as outer ip4-in-ip6 tunnel source addressAxel Neumann2018-06-234-4/+4
| | | | | | | | | | | | | | | | The 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch kernel patches break the possibility for using an ip4ip6 tunnel interface as a fall back interface accepting ip4-in-ip6 tunneled packets from any remote address. This works out of the box with any normal (non-666-patched) kernel and can be configured by setting up an 'ip -6 tunnel' with type 'any' or 'ip4ip6' and a remote address of '::'. The misbehavior comes with line 290 the patch which discards all packets that do not show the expected saddr, even if no single fmr rule was defined and despite the validity of the saddr was already approved earlier. Signed-off-by: Axel Neumann <neumann@cgws.de> Acked-by: Hans Dedecker <dedeckeh@gmail.com>
* mediatek: Add support for the UniElec U7623-02Kristian Evensen2018-06-2211-8/+805
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MT7623A-based UniElec U7623-02 router, with eMMC storage and 512MB RAM. The router can be delivered with NAND Flash and more memory, but I only have access to the one configuration. The DTS is structured in such a way that adding support for more/different storage/memory should be straight forward. The device has the following specifications: * MT7623A (quad-core, 1.3 GHz) * 512MB RAM (DDR3) * 8GB storage (eMMC 4.5) * 2x normal miniPCIe slots * 1x miniPCIe slot that is connected via an internal USB OTG port * 5x 1Gbps Ethernet (MT7530 switch) * 1x UART header * 1x USB 3.0 port * 1x SATA 3.0 * 1x 40P*0.5mm FPC for MIPI LCD * 1x SIM slot * 12x LEDs (2 GPIO controlled) * 1x reset button * 1x DC jack for main power (12V) The following has been tested and is working: * Ethernet switch * miniPCIe slots (tested with Wi-Fi cards) * USB 3.0 port * sysupgrade * reset button Not working: * The miniPCIe connected via USB OTG. For the port to work, some MUSB glue must be added. I am currently in the process of porting the glue from the vendor SDK. Not tested: * SATA 3.0 * MIPI LCD Installation: The board ships with u-boot, and the first installation needs to be done via the bootloader using tftp. Step number one is to update the MBR of the eMMC, as the one that ships with the device is broken. Since the device can ship with different storage sizes, I will not provide the exact steps for creating a valid MBR. However, I have made some assumptions about the disk layout - there must be one 8MB recovery partition (FAT32) and a partition for the rootfs (Linux). The board loads the kernel from block 0xA00 (2560) and I have reserved 32MB for the kernel (65536 blocks). I have aligned the partitions on the erase block size (4096 byte), so the recovery partition must start on block 69632 and end on 86016 (16385 sectors). The rootfs is assumed to start on sector 90112. In order to install the mbr, you run the following commands from the u-boot command line: * tftpboot ${loadaddr} <name of mbr file> * mmc device 0 * mmc write ${loadaddr} 0x00 1 Run the following commands to install + boot OpenWRT: * tftpboot ${loadaddr} openwrt-mediatek-mt7623-7623a-unielec-u7623-02-emmc-512m-squashfs-sysupgrade-emmc.bin.gz * run boot_wr_img * run boot_rd_img * bootm Recovery: In order to recover the router, you need to follow the installation steps above (no need to replace MBR). Notes: * F2FS is used as the overlay filesystem. * The device does not ship with any valid MAC address, so a random address has to be generated. As a work-around, I write the initial random MAC to a file on the recovery partition. The MAC of the WAN interface is set to the MAC-address contained in this file on each boot, and the address of the LAN-interfaces are WAN + 1. The MAC file is kept across sysupgrade/firstboot. My approach is slightly different than what the stock image does. The first fives bytes of the MAC addresses in the stock image are static, and then the last byte is random. I believe it is better to create fully random MAC addresses. * In order to support the miniPCIe-slots, I needed to add missing pcie-nodes to mt7623.dtsi. The nodes are just c&p from the upstream dtsi. * One of the USB3.0 phys (u3phy2) on the board can be used as either USB or PCI, and one of the wifi-cards is connected to this phy. In order to support switching the phy from USB to PCI, I needed to patch the phy-driver. The patch is based on a rejected (at least last time I checked) PCI-driver submitted to the linux-mediatek mailing list. * The eMMC is configured to boot from the user area, and according to the data sheet of the eMMC this value can't be changed. * I tried to structure the MBR more nicely and use for example a FAT32-parition for the kernel, so that we don't need to write/read from some offset. The bootloader does not support reading from FAT32-paritions. While the command (fatload) is there, it just throws an error when I try to use it. * I will submit and hope to get the DTS for the device accepted upstream. If and when that happens, I will update the patches accordingly. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* kernel: cleanup offload hooks on netdev unregisterChen Minqiang2018-06-221-0/+96
| | | | Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* lantiq: fix arcadyan vg3503j switch port indexingMathias Kresin2018-06-211-1/+1
| | | | | | | Both version of the vg3503j have the LAN1 labelled port connected to switch port 4 and the LAN2 labelled port connected to switch port 2. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add support for Phicomm K2GChuanhong Guo2018-06-215-1/+155
| | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: MediaTek MT7620A - Flash: 8 MB - RAM: 64 MB - Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5) - Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped with external PA. - UART: 1 x UART on PCB - 57600 8N1 Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: Add support for Mikrotik RouterBOARD RBM33gTobias Schramm2018-06-217-1/+187
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Mikrotik RouterBOARD RBM33g. =Hardware= The RBM33g is a mt7621 based device featuring three gigabit ports, 2 miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male onboard RS-232 serial port. Additionally there are a lot of accessible GPIO ports and additional buses like i2c, mdio, spi and uart. ==Switch== The three Ethernet ports are all connected to the internal switch of the mt7621 SoC: port 0: Ethernet Port next to barrel jack with PoE printed on it port 1: Innermost Ethernet Port on opposite side of RS-232 port port 2: Outermost Ethernet Port on opposite side of RS-232 port port 6: CPU ==Flash== The device has two spi flash chips. The first flash chips is rather small (512 kB), connected to CS0 by default and contains only the RouterBOOT bootloader and some factory information (e.g. mac address). The second chip has a size of 16 MB, is by default connected to CS1 and contains the firmware image. ==PCIe== The board features three PCIe-enabled slots. Two of them are miniPCIe slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2). Each of the miniPCIe slots is connected to a dedicated mini SIM socket on the back of the board. Power to all three PCIe-enabled slots is controlled via GPIOs on the mt7621 SoC: PCIe0: GPIO9 PCIe1: GPIO10 PCIe2: GPIO11 ==USB== The board has one external USB 3.0 port at the rear. Additionally PCIe port 0 has a permanently enabled USB interface. PCIe slot 1 shares its USB interface with the rear USB port. Thus only either the rear USB port or the USB interface of PCIe slot 1 can be active at the same time. The jumper next to the rear USB port controls which one is active: open: USB on PCIe 1 is active closed: USB on rear USB port is active ==Power== The board can accept both, passive PoE and external power via a 2.1 mm barrel jack. The input voltage range is 11-32 V. =Installation= ==Prerequisites== A USB -> RS-232 Adapter and a null modem cable are required for installation. To install an OpenWRT image to the device two components must be built: 1. A openwrt initramfs image 2. A openwrt sysupgrade image ===initramfs & sysupgrade image=== Select target devices "Mikrotik RBM33G" in openwrt menuconfig and build the images. This will create the images "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output directory. ==Installing== **Make sure to back up your RouterOS license in case you do ever want to go back to RouterOS using "/system license output" and back up the created license file.** Serial settings: 115200 8N1 The installation is a two-step process. First the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted via tftp: 1. Set up a dhcp server that points the bootfile to tftp server serving the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" initramfs image 2. Connect to WAN port (left side, next to sys-LED and power indicator) 3. Connect to serial port of board 4. Power on board and enter RouterBOOT setup menu 5. Set boot device to "boot over ethernet" 6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server allows dynamic bootp) 6. Save config 7. Wait for board to boot via Ethernet On the serial port you should now be presented with the OpenWRT boot log. The next steps will install OpenWRT persistently. 1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device using scp. 2. Write openwrt to flash using "sysupgrade openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" Once the flashing completes reboot the router and let it boot from flash. It should boot straight to OpenWRT. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: Add lzma-loader targetsTobias Schramm2018-06-211-0/+16
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: Add support for mt7621 to lzma-loaderTobias Schramm2018-06-215-18/+60
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: fix Newifi D1 mtd partitionDeng Qingfang2018-06-211-1/+1
| | | | | | Newifi D1 has 32 MiB flash, so the firmware partition size should be 0x1fb0000 Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* brcm2708: Add wifi driver, firmware and NVRAM for Raspberry Pi 3 bChristo Nedev2018-06-201-1/+1
| | | | | | | | | | | | 2708 -> 43430 -> pi0w 2709 -> 43430 -> pi3b 2709 -> 43455 -> pi3bplus 2710 -> 43430 -> pi3b 2710 -> 43455 -> pi3bplus Signed-off-by: Christo Nedev <christo.nedev@gmail.com>
* ar71xx: add support for TP-LINK Archer C7 v5Arvid E. Picciani2018-06-209-1/+228
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros QCA9563+QCA9880. Specification: - 750/400/250 MHz (CPU/DDR/AHB - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 10x LED, 2x button - UART header on PCB Flash instruction: 1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin and rename it to ArcherC7v5_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Arvid E. Picciani <aep@exys.org>
* octeon: Add and set CPU type Octeon+ as defaultDaniel Engberg2018-06-201-1/+1
| | | | | | | | | | | | | | The lowest CPU type used by supported Octeon platform is Octeon+ (EdgeRouter Lite) while EdgeRouter Pro/ER-8 uses Octeon II which is backwards compatible with Octeon+. Sources: https://community.ubnt.com/t5/EdgeRouter/EdgeRouter-Pro-CPU/td-p/654599 https://www.cavium.com/octeon-II-CN68XX.html "OCTEON II family is fully software compatible with the widely-adopted OCTEON Plus family" Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
* brcm2708: Add wifi driver, firmware and NVRAM for RPi1Daniel Golle2018-06-201-0/+1
| | | | | | | | Apparently there are RPi1 devices with BRCM43430 wifi, such as the Pi Zero W. Add the necessary packages for that to the image generated for those boards as well. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: ar934x: use irq-ath79-intc driver and enable wmacJohann Neuhauser2018-06-204-9/+66
| | | | Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: qca95xx: add new intc2, correct intc3 and add second pcie on qca9557Johann Neuhauser2018-06-203-9/+49
| | | | Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ath79: fix irq-ath79-intc driver and add support for other ath79 SoCsJohann Neuhauser2018-06-201-14/+52
| | | | | | | | | | | | | | Add the missing enable and disable function. Remove dummy mask and unmask function and use the one provided by irq_dummy_chip. Allow interrupt status register being defined from dts. Add ddr_wb_flush for ar934x/qca953x. Rename controller name to qca,ar9340-intc because this design was first introduced in AR934x. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* ramips: add support for ELECOM WRC-1167GHBK2-SINAGAKI Hiroshi2018-06-196-4/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - MT7621A (2-Cores, 4-Threads) - 128 MB of RAM (DDR3) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz - MediaTek MT7615D - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 2x keys - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 57600 bps Flash instruction using factory image: 1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin" 2. Connect the computer to the LAN port of WRC-1167GHBK2-S 3. Connect power cable to WRC-1167GHBK2-S and turn on it 4. Access to "http://192.168.2.1/details.html" and open firmware update page ("手動更新（アップデート）") 5. Select the factory image and click apply ("適用") button 6. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-199-7/+484
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mt7621: fix wireless package selectionMathias Kresin2018-06-191-5/+4
| | | | | | | Add wpad-mini if wireless drivers are included. Drop the mt76 package if both of the provided drivers are included with their own packages. Signed-off-by: Mathias Kresin <dev@kresin.me>
* arc770: bump kernel to 4.14Evgeniy Didin2018-06-193-23/+26
| | | | | | | | | | Currently arc770 is no more "source-only". Lets update Linux kernel version from 4.9 to 4.14 for arc770. config-4.14 was simply regenerated with "make kernel_menuconfig". Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: John Crispin <john@phrozen.org>
* ar71x: add support for Mikrotik Routerboard wAP RDavid Ehrmann2018-06-198-4/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Mikrotik wAP R (RBwAPR-2nD). The change is based on 3b15eb0 which added support for the wAP 2nD. This change lacks LED support. Specifications: - SoC: Qualcomm QCA9531 (650 MHz) - RAM: 64 MB - Storage: 16 MB NOR SPI flash - Wireless: built-in QCA9531, 802.11b/g/n 2x2:2 - Ethernet: 1x100Mbps - Power: 9-30V Passive PoE, 9-30V DC jack, 9-30V automotive jack - SIM card slot - Mini-PCIe slot Installation: 1. Login to the Mikrotik WebUI to backup your licence key 2. Change the following settings in System->Routerboard->Settings: - Boot device: try ethernet once then NAND - Boot protocol: DHCP - Force Backup Booter: checked 3. Setup a DHCP/BOOTP server with: - DHCP-Option 66 (TFTP server name) pointing to a local TFTP server within the same subnet of the DHCP range - DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image, e.g. openwrt-ar71xx-mikrotik-vmlinux-initramfs.elf 4. Power off the device 5. If this is the second attempt to boot OpenWRT or the boot device isn't "try ethernet once then NAND," press and hold the reset button while powered off. If this is the first attempt, this step isn't necessary. 6. Power on the device, holding the reset button for 15-20s if already pressed from the previous step. The board should load and start the initramfs image from the TFTP server. Login as root/without password to the started OpenWRT via SSH listing on IPv4 address 192.168.1.1. Use sysupgrade to install OpenWRT. Revert to RouterOS Use the "rbcfg" package on in OpenWRT: - rbcfg set boot_protocol bootp - rbcfg set boot_device ethnand - rbcfg apply Open Netinstall and reboot routerboard. Now Netinstall sees RouterBOARD and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall. Signed-off-by: David Ehrmann <ehrmann@gmail.com>
* ramips: improve ethernet driver performance with GRO/TSOFelix Fietkau2018-06-193-76/+105
| | | | | | | | | | | GRO stores packets as fraglist. If they are routed back to the ethernet device, they need to be re-segmented if the driver does not support sending fraglists. Add the missing support for that, along with a missing feature flag that allows full routed GRO->TSO offload. Considerably reduces CPU utilization for routing Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: fix qm5p-ac-v2 dts fileJohn Crispin2018-06-181-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: add support for Fritz!WLAN Repeater 450EDavid Bauer2018-06-1813-1/+212
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the AVM Fritz!WLAN Repeater 450E SOC: Qualcomm QCA9556 (Scorpion) 560MHz MIPS74Kc RAM: 64MB Zentel A3R12E40CBF DDR2 FLASH: 16MiB Winbond W25Q128 SPI NOR WLAN1: QCA9556 2.4 GHz 802.11b/g/n 3x3 INPUT: WPS button LED: Power, WiFi, LAN, RSSI indicator Serial: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4GHz WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - Most LEDs Not working: - 2 RSSI LEDs AVM used for RSSI{0,1} two of the Ethernet PHYs LEDs which they control over MDIO. Our driver doesn't expose these LEDs as GPIOs. While it is possible to implement this feature, it would require an additional kernel patch for a minor functionality. Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 192.168.178.1. Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. You need to powercycle the Device afterwards to boot OpenWRT. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: fix incorrect speed setting on QCA9556David Bauer2018-06-181-3/+17
| | | | | | | | | The QCA9556 only has a SGMII interface. However the speed on the ethernet link is set for the non-existant xMII interface. This commit fixes this behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for tl-wr1043nd v2/v3Lucian Cristian2018-06-186-23/+341
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add initial nand support for gl-ar300mMarty E. Plummer2018-06-187-1/+123
| | | | Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
* ath79: initial gl-ar300m supportMarty E. Plummer2018-06-185-0/+436
| | | | Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
* mvebu: enable CONFIG_HW_RANDOMHannu Nyman2018-06-181-0/+1
| | | | | | | | | Enable the Hardware Random Number Generator Core infrastructure in kernel. Needed for hardware random number generator drivers like chaoskey Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ipq806x: D7800 only has a single sata portJohn Crispin2018-06-181-0/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mips: fix dynamic ftraceVincent Wiemann2018-06-181-3/+8
| | | | | | | | | | The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as dynamic ftrace depends on -mlong-calls. See http://patchwork.linux-mips.org/patch/675/ Thus we always set -mlong-calls if the kernel is being compiled with dynamic ftrace support. Signed-off-by: Vincent Wiemann <webmaster@codefetch.de>
* mvebu: backport ahci_mvebu errata patchsetJeremiah McConnell2018-06-182-0/+334
| | | | | | | | | | | | Marvell ahci hardware requires a workaround to prevent eSATA failures on hotplug/reset when used with multi-bay external enclosures. Errata Ref#226 - SATA Disk HOT swap issue when connected through Port Multiplier in FIS-based Switching mode. These patches backport the workaround from 4.17. Signed-off-by: Jeremiah McConnell <miah@miah.com>
* ath79: fix rx ring buffer stall qca956xLucian Cristian2018-06-181-1/+2
| | | | | | when ported from ar71xx to ath79 the qca9560-eth was omitted Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ar71xx: add kmod-usb-ehci to fix USB on RB hAP ACThomas Nixon2018-06-181-1/+1
| | | | Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* ipq40xx: add support for ZyXEL WRE6606Magnus Frühling2018-06-187-2/+300
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
* ath79: add tl-wr1043nd-v4 support everything is workingLucian Cristian2018-06-185-11/+271
| | | | | | | tplink-safeloader: resize kernel partition kernel 4.14 is much bigger, resize the partition Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: add ubiquiti unifi ap ac lite/lrLucian Cristian2018-06-184-0/+171
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: ag71xx: fix pll-data setting for ar7242/ar934x/qca955x/qca956xWeijie Gao2018-06-181-10/+7
| | | | | | | | | | | ar71xx/ar913x series use the old pll registers and settings. However started from ar7242, a new pll register is introduced and the pll setting is much simpler. This can be observed from dev-eth.c from the ar71xx target. Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ath79: add support for Phicomm K2TWeijie Gao2018-06-187-0/+587
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds dts for qca956x and also support for Phicomm K2T The qca965x.dtsi adds nearly all the necessary components. Both ath9k AHB and PCIe worked well. The Phicomm K2T uses MTD partition 'config' to store the mac addresses in JSON format. To extract these fields correctly, a script is introduced: /lib/functions/k2t.sh This script provides a helper function to extract mac addresses, and is used in three places. Hardware spec of Phicomm K2T: CPU: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337 WiFi 5.8GHz: QCA9886 Flash instruction: Apply sysupgrade.bin via serial console: tftp 0x80000000 sysupgrade.bin && erase 0x9f090000 +$filesize && cp.b $fileaddr 0x9f090000 $filesize Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ipq40xx: essedma: fixup ip alignChen Minqiang2018-06-181-0/+26
| | | | | | | | This fixup ip align in essedma driver rx path see cat /proc/cpu/alignment which reports alignment-fixups without this fix. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* kernel: atm: pppoatm fix vc-mux connection failuresKevin Darbyshire-Bryant2018-06-181-0/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Backport a hot off the press upstream kernel ATM fix: Preserve value of skb->truesize when accounting to vcc "There's a hack in pskb_expand_head() to avoid adjusting skb->truesize for certain skbs. Ideally it would cover ATM too. It doesn't. Just stashing the accounted value and using it in atm_raw_pop() is probably the easiest way to cope." The issue was exposed by upstream with: commit 14afee4b6092fde451ee17604e5f5c89da33e71e Author: Reshetova, Elena <elena.reshetova@intel.com> Date: Fri Jun 30 13:08:00 2017 +0300 net: convert sock.sk_wmem_alloc from atomic_t to refcount_t But an earlier commit left the ticking timebomb: 158f323b9868 ("net: adjust skb->truesize in pskb_expand_head() Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging assistance and to David Woodhouse <dwmw2@infradead.org> for further guidance, cajoling & patience in interpreting the debug I was giving him and producing a fix! Fixes FS#1567 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* lantiq: atm: fix ifx_atm driver integrationKevin Darbyshire-Bryant2018-06-181-19/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When upstream kernel introduced commit c55fa3cccbc2c672e7f118be8f7484e53a8e9e77 we incorrectly updated our hack integration patch that updates atm/common.c +++ b/net/atm/common.c @@ -62,10 +62,16 @@ static void vcc_remove_socket(struct soc write_unlock_irq(&vcc_sklist_lock); } +struct sk_buff* (*ifx_atm_alloc_tx)(struct atm_vcc *, unsigned int) = NULL; +EXPORT_SYMBOL(ifx_atm_alloc_tx); + static bool vcc_tx_ready(struct atm_vcc *vcc, unsigned int size) { struct sock *sk = sk_atm(vcc); + if (ifx_atm_alloc_tx != NULL) + return ifx_atm_alloc_tx(vcc, size) The correct solution is to drop our ifx_atm_alloc_tx replacement hack entirely and let the kernel do its thing. In reality neither pppoatm or BR2684 interfaces actually hit this code, so the incorrect integration would only be noticed with direct socket calls which we are unaware of a use-case. This is not the solution to pppoatm vc-mux failing to work which started the whole investigation, but let's fix it up anyway. With sincerest thanks to David Woodhouse <dwmw2@infradead.org> & Mathias Kresin <dev@kresin.me>. Tested-on: lantiq, BT HomeHub 5a Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 4.9 to 4.9.109Koen Vandeputte2018-06-182-4/+4
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* bcm53xx: exit if writing kernel during sysupgrade failsRafał Miłecki2018-06-181-2/+2
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: drop not ready support for Luxul devicesRafał Miłecki2018-06-181-30/+0
| | | | | | | | Support for these devices isn't ready yet and it was only accidentally pushed in the commit 0da9303e5b44 ("mac80211: backport "brcmfmac: cleanup and some rework" from 4.17"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mvebu: replace espressobin spi patch with upstream oneTomasz Maciej Nowak2018-06-182-29/+45
| | | | | | | | | For easier future kernel bumps replace spi patch with upstream version slightly modified. The modification removes partition definitions which has been diffrent for some U-Boot versions. Also this removes unnecessary i2c definition which was in the old patch. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: reduce speed to gen1 for espressobin pcieTomasz Maciej Nowak2018-06-182-0/+116
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the beginning there's been an issue with initializing the Atheros based MiniPCIe wireless cards. Here's an example of kerenel log: OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit] pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref] [...] advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k 0000:00:00.0: enabling device (0000 -> 0002) advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40 ath9k 0000:00:00.0: request_irq failed advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k: probe of 0000:00:00.0 failed with error -22 The same happens for ath5k cards, while ath10k card didn't appear at all (not detected): OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link never came up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) advk-pcie d0070000.pcie: config read/write timed out Following the issue on esppressobin.net forum [1] the workaround seems to be limiting the speed of PCIe bridge to 1st generation. This fixed the initialisation of all tested Atheros wireless cards. The change shouldn't affect the performance for wireless cards, it could reduce the performance of storage controller cards but since OpenWrt focuses on wireless connectivity, fixing compatibility with wireless cards should be a priority. For the record, the iwlwifi and mt76 cards were not affected by this issue. 1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 12:51:38 +0000