| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
| |
Use keycodes that matches the intended use case based on the label.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
| |
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
| |
Move the mkwrgimg build step to the makefile. It will be required by
other boards as well.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
| |
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this
GPIO is mentioned in the GPL tarball, it doesn't do anything. The
2.4/5 GHz LEDs are connected to the wifi chips and not be controlled
from the the userspace.
Use the LEDs names/colours as they are used in the board manuals. Merge
redundant LED configurations. Use the phy[0|1]tpt trigger for the
wireless LEDs. Remove the workarounds for the not controllable wireless
LEDs.
Fix spi compatible strings and remove superfluous spi-max-frequency
parameters.
If there are two power leds, use one for indicating normal operation and
one for failsafe/upgrade. Keep the on/off state of the main power led
during boot.
Use the usb pinmux settings from the nbg6817 gpl sources.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Set the pinmux to the values found in the GPL tarballs of the boards.
Remove pinmux which are is not used (like nand pinmux for spi
flash boards).
This allows to use the wan orange led of the C2600 which had a wrong
pinmux before. Might fix buttons or leds of other boards as well.
Fix the LED color and the ledswitch key code of the C2600. Rename the
ledgnr to ledswitch.
Add support for indication the boot state using LEDs to the D7800,
NBG6817, R7500 and R7500v2.
Change GPIO active to readable values in D7800, EA8500, R7500,
R7500v2 and R7800.
Change gpioexport to gpio pinmux.
Add proper "drive strenght" to i2c4_pins and use it for RPM on
C2600, D7800, EA8500, R7500, R7500v2.
Remove pcie pinmux from D7800.
Move pinctrl to correct place in NBG6817 and R7800.
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
|
|
|
|
|
|
| |
This allows adding devices to the PCIe controller in the .dts files.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
|
|
|
|
|
|
| |
This allows specifying PCI devices as children of the PCIe controller
node to pass configuration data to them.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
|
|
|
|
|
|
|
|
|
| |
Fix bug that LEDE failed to boot with this message:
WARNING: CPU: 2 PID: 1 at drivers/spi/spi-mt7621.c:214
mt7621_spi_transfer_one_message+0x28c/0x620()
Signed-off-by: Yong-hyu, Ban <perillamint@gentoo.moe>
|
|
|
|
|
|
| |
Use gpio.h definition of GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Remove unused backup partition to increase available JFFS space. As long as U-Boot env variable "bootcount" is < 3 (reset to 0 after boot by init script) SamKnow's U-Boot will not attempt to boot from the backup flash address (0xe30000).
Signed-off-by: Andrew Yong <me@ndoo.sg>
|
|
|
|
|
|
|
| |
This reverts commit 539ae47103b7de5cecb1a94beab0acb97ef7df1d.
According to reports, this introduces a regression on WRT3200ACM
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
None of the devices uses an usb led at all.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
| |
This device uses NAND FLASH, so it should be kept in nand subtarget.
Also, inlcude in packages kmod-usb-ledtrig-usbport instead of
obsolete kmod-ledtrig-usbdev.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
|
|
|
|
|
|
|
| |
Other virtualization options are already enabled, so this is only a
small addition
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
CONFIG_CRYPTO_DEV_SUN4I_SS was previously set to y but did not take
effect because of the absence of CONFIG_CRYPTO_HW=y
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, the device-tree partition is marked as read-only.
Hence, userspace tools like mtd can't write into the partition.
This however will be necessary in case the DTB needs to be
updated.
This patch also adds the kernel.dtb image, so the compiled
DTB is exported as a file and available in the binary
directory along the firmware images.
Note: the u-boot does expects the dtb to be a uimage.
To update the dtb manually:
1. copy the generated dtb to the router.
2. mtd erase /dev/mtd2
3. mtd write wndr4700.dtb /dev/mtd2
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Unlike x86, kvm for arm has to be built into the kernel. The kernel
config was prepared with the following command
make kernel_menuconfig CONFIG_TARGET=platform
Then enable ARM_LPAE, VIRTUALIZATION, KVM in that order
Other config changes are done by the build system. The following text
tries to explain some of them, for archive purposes probably...
- BUILD_BIN2C. It was dropped probably because the prompt is empty and
no other config option selects it. bin2c is a host executable for
converting binary content to a piece of c code for inclusion
- CRYPTO_DEV_SUN4I_SS. It was dropped because the dependency CRYPTO_HW
was not enabled. Setting that aside, packaging it as a loadbable
module in lieu of other sunxi specific modules seems more appropriate
- PGTABLE_LEVELS. It was changed from 2 to 3 because 3 is the default
when ARM_LPAE is enabled
- HAVE_KERNEL_GZIP, etc.. These are enabled in generic config
- SCHED_INFO, ZLIB_INFLATE. These were dropped probably for the same
reason as for BUILD_BIN2C
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
|
|
|
|
|
|
| |
Replaces plain ext4 images
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
| |
Unify switch configuration on Linksys WRTxx00AC series.
LAN = eth0, WAN = eth1
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Dlink DWR-512-B modem is a ralink 5350 processor based embedding
a 3G mini-pcie router.
The oem JBOOT bootloader has to be replaced by a RT5350 SDK
U-Boot such as https://github.com/stevenylai/ralink_sdk - U-Boot
configured for the RT5350 256MiB SDR.
Main reason to change the bootloader is the encrypted header used to
store the kernel image. In this way an image can only be generated
using the propietary binboy tool (included in the GPL distribution
from Dlink). The binboy tool doesn't allow to modify the kernel/rootfs
partition scheme. This is considered a big constraint (limited kernel
size and inefficient usage of flash space).
For interested people I pubblished the details of my investigation
about the encrypted firmware header here:
http://lists.infradead.org/pipermail/lede-dev/2016-October/003435.html
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
|
|
|
|
| |
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix a typo in mt7621.dtsi compatible string. Disable spi, sdhci and pci
in mt7621.dtsi and enable the nodes in the indiviual board dts files.
The nodes require further device specific configuration anyway.
Remove the m25p80@0 spi child node from mt7621.dtsi and add the
chunked-io parameter to the individual board dts files. Fix the spi
flash compatible string for the WNDR3700V5.
Drop the mt7621-eval-board compatible string for all boards which are
not the eval board.
Drop the linux,modalias parameter from spi flash node.
Remove the xhci node from board files, it is already enabled in dtsi.
Disable xhci for boards not having usb ports populated.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
| |
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
| |
Fix configuration files for the Livebox 1 routers.
- Add status led
- Set eth0 as the LAN port, for coherence with RedBoot and comfortability.
- Add led triggers
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
|
|
|
|
|
|
|
|
| |
Fix Image generation for the Livebox 1
- missing "relocate-kernel", wrong "LOADADDR", fix it
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
|
|
|
|
|
|
|
|
| |
Fix the DTS file for the Livebox 1 routers:
- part probe wrong, it should be RedBoot (uppercase matters)
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
|
|
|
|
|
|
|
|
| |
Fix the DTS file for the Livebox 1 routers:
- leds are totally wrong, fix them.
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
|
|
|
|
|
|
|
|
| |
Fix the DTS file for the Livebox 1 routers:
- no failsafe button, use button 1 for this purpose
Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
|
|
|
|
|
|
|
| |
fix in sdhci Use ralink_soc == MT762X_SOC_MT7621AT instead of CONFIG_SOC_MT7621 which is
wrong and breaks builds on mt7620a-similar platforms (MT7621, MT7688)
Signed-off-by: Andrew Yong <me@ndoo.sg>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Enable work-arounds present in the code commented-out but needed to write to
sdcard on mt7621 which currently causes kernel to oops when engaging in
serious writing to sdcard. With this change applied, there are still
occasional warnings thrown by the mmc driver, however, at least it no longer
crashes the system and even large writes (full-card dump/erase/write/compare)
don't show any corruption.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Rebase to LEDE and added "CONFIG_SOC_MT7621" check to ensure non-MT7621 devices do not face performance regressions.
Signed-off-by: Andrew Yong <me@ndoo.sg>
|
|
|
|
|
|
|
|
| |
This adds the patch submitted to upstream that adds BQL to the mvneta
driver: https://patchwork.kernel.org/patch/9328413/. Helps latency under
load when the physical link is saturated.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
|
|
|
|
|
|
| |
Use dwc2 by default on all danube boards.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
Parameters for dwc2 on lantiq.
A separate dwc2_core_params structure is defined for danube because danube
fifo sizes are large enough to be autodetected. This is not the case on
arx and vrx.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
|
|
|
|
|
|
|
|
|
| |
Device tree binding for dwc2 usb driver on danube.
Leave old ifxhcd-danube driver as an alternative.
Also adds dr_mode = "host" to eliminate warning on boot.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
|
|
|
|
|
|
| |
Initialise dwc2 usb driver on danube boards as well as ar9 and vr9.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the Cisco Meraki MX60/MX60W Security
Appliance. Flashing information can be found at
https://github.com/riptidewave93/LEDE-MX60
Specs are as follows:
AppliedMicro APM82181 SoC at 800MHz
1GiB NAND - Samsung K9K8G08U0D
512MB DDR RAM - 4x Nanya NT5TU128M8GE-AC
Atheros AR8327-BL1A Gigabit Ethernet Switch
1x USB 2.0 Port
More info can be found at https://wiki.openwrt.org/toh/meraki/mx60
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
|
|
|
|
| |
Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
|
|
|
|
|
|
|
| |
This patch fixes the ethernet switch initial config for Mikrotik RB450 and RB450G.
The previous version wrongly changed the RouterStation Pro config. This one creates a specific config for the RB450G and leaves the RouterStation Pro unchanged.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
|
|
|
|
|
|
|
|
|
| |
CPE830 is a clone of AP90Q, with different type of antenna (panel)
and additional 4 LEDs for WiFi signal level indication.
Use the same flash approach as for YunCore AP90Q.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
YunCore CPE870 is an outdoor CPE/AP based on Atheros AR9341.
Short specification:
- 535/400/200 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz with external PA (SKY65174-21), up to 30 dBm
- internal 14 dBi panel antenna
- 8x LED, 1x button
- UART (JP1) header on PCB
Flash instruction (do it under U-Boot, using UART):
1. tftp 0x80060000 lede-ar71xx-generic-cpe870-squashfs-sysupgrade.bin
2. erase 0x9f020000 +$filesize
3. cp.b $fileaddr 0x9f020000 $filesize
4. setenv bootcmd "bootm 0x9f020000"
5. saveenv && reset
Vendor firmware access (login/password): Admin/5up
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
YunCore AP90Q is an outdoor CPE/AP based on Qualcomm/Atheros QCA9531 v2.
Short specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, passive PoE support
- 64/128 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz with external PA, up to 29 dBm
- 2x internal 5 dBi omni antennas
- 4x LED, 1x button
- UART (JP1) header on PCB
Flash instruction under U-Boot, using UART:
1. tftp 0x80060000 lede-ar71xx-generic-ap90q-squashfs-sysupgrade
2. erase 0x9f050000 +$filesize
3. cp.b $fileaddr 0x9f050000 $filesize
4. setenv bootcmd "bootm 0x9f050000"
5. saveenv && reset
Flash instruction under vendor fimrware, using telnet/SSH:
1. Connect PC with 192.168.1.x address to WAN port
2. Power up device, enter failsafe mode with button (no LED indicator!)
3. Change root password and reboot (mount_root, passwd ..., reboot -f)
4. Upload lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin to /tmp using SCP
5. Connect PC with 192.168.188.x address to LAN port, SSH to 192.168.188.253
6. Invoke:
- cd /tmp
- fw_setenv bootcmd "bootm 0x9f050000"
- mtd erase firmware
- mtd -r write lede-ar71xx-generic-ap90q-squashfs-sysupgrade.bin firmware
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
COMFAST CF-E380AC v1/v2 is a ceiling mount AP with PoE
support, based on Qualcomm/Atheros QCA9558+QCA9880+AR8035.
There are two versions of this model, with different RAM
and U-Boot mtd partition sizes:
- v1: 128 MB of RAM, 128 KB U-Boot image size
- v2: 256 MB of RAM, 256 KB U-Boot image size
Version number is available only inside vendor GUI,
hardware and markings are the same.
Short specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 1x 10/100/1000 Mbps Ethernet, with PoE support
- 128 or 256 MB of RAM (DDR2)
- 16 MB of FLASH
- 3T3R 2.4 GHz, with external PA (SE2576L), up to 28 dBm
- 3T3R 5 GHz, with external PA (SE5003L1), up to 30 dBm
- 6x internal antennas
- 1x RGB LED, 1x button
- UART (T11), LEDs/GPIO (J7) and USB (T12) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As we already have support for CF-E316N v2 and many devices from
this vendor look similar, the support was included in existing
mach-*.c file, with few cleanups and fixes.
All 3 devices are based on Qualcomm/Atheros QCA9531 v2.
COMFAST CF-E320N v2 is a ceiling mount AP with PoE support.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, both with PoE support
- 64 MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x RGB LED, 1x button
- UART (J1), GPIO (J9) and USB (J2) headers on PCB
- external watchdog (Pericon Technology PT7A7514)
COMFAST CF-E520N/CF-E530N are in-wall APs with USB and PoE support.
They seem to have different only the front panel.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 2x 10/100 Mbps Ethernet, WAN with PoE support
- 1x USB 2.0 (in CF-E520N covered by panel, available on PCB)
- 32 MB of RAM (DDR2)
- 8 MB of FLASH
- 2T2R 2.4 GHz, up to 22 dBm
- 2x internal antennas
- 1x LED, 1x button
- UART (J1) headers on PCB
Flash instruction:
Original firmware is based on OpenWrt.
Use sysupgrade image directly in vendor GUI.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
| |
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
|
|
|
|
| |
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
|