| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
| |
Most ar7 devices have only 16 MiB RAM, so select low_mem to give them
a chance to work.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41532
|
|
|
|
|
|
|
|
| |
This is compile tested only, please run test and report back.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41531
|
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41530
|
|
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41529
|
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41528
|
|
|
|
|
|
|
|
|
|
|
| |
When the Ethernet controller is powered down and someone wants to
access the mdio bus like the witch driver (b53) the system crashed if
PCI_D3hot was set before. This patch deactivates this power sawing mode
when a switch driver is in use.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41527
|
|
|
|
|
|
|
|
|
|
|
|
| |
According to the thread https://forum.openwrt.org/viewtopic.php?id=48281
b53 uses GPIO 7:
[ 4.470000] b53_common: [DBG] b53_switch_reset_gpio using 7
and causes device to self-reboot. GPIO 8 was found in CFE boot log:
"Reset switch via GPIO 8 ..."
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41526
|
|
|
|
|
|
| |
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41522
|
|
|
|
|
|
| |
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41521
|
|
|
|
|
|
|
|
|
| |
https://dev.openwrt.org/ticket/14406
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41520
|
|
|
|
|
|
| |
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41517
|
|
|
|
|
|
|
|
|
| |
https://dev.openwrt.org/ticket/16991
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41516
|
|
|
|
|
|
|
|
|
|
| |
Now the mac address is increased by two for the first fallback mac
address. It could be that the address increased should be used for the
wan port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41515
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
collisions.
The address prefix 00:90:4C is used by Broadcom in their initial
configuration. When a mac address with the prefix 00:90:4C is used
all devices from the same series are sharing the same mac address.
To prevent mac address collisions we replace them with a mac address
based on the base address.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41513
|
|
|
|
|
|
|
|
|
| |
Without this patch the switch config for the adm switch did not worked,
because hey are not names eth0.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41512
|
|
|
|
|
|
|
|
|
| |
This patch deactivates the statistics, adds a missing lock
initialization and fixes a waring.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41511
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41507
|
|
|
|
|
|
|
|
| |
Reduces kernel size by about 24k (6k compressed).
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41506
|
|
|
|
|
|
|
|
| |
https://patchwork.linux-mips.org/patch/6940/
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41505
|
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41501
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Old OpenWrt releases were using network configs that are not valid
anymore. They were specifying ports tagging in a different way (or were
not tagging CPU at all) and were using VID 0 which is a reserved value.
Modifying network configuration to apply all needed changes would be
pretty tricky. Script /etc/init.d/netconfig that generates new config is
quite complex itself.
So instead let's save the most important settings, regenerate config
from the scratch and restore values. This should work for 99% of users.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 41500
|
|
|
|
|
|
| |
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41499
|
|
|
|
|
|
|
|
|
|
| |
Realview is mostly used as a QEMU development platform, which will provide a
built-in DHCP server to NAT or bridge the connection outside of the emulated
environment.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 41495
|
|
|
|
|
|
|
|
|
| |
This is not needed since our toolchain produces the expected binaries for the
target CPU.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 41494
|
|
|
|
|
|
|
|
| |
CONFIG_LEDS_GPIO_REGISTER is selected by the bcm47xx arch code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41488
|
|
|
|
|
|
| |
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41487
|
|
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 41486
|
|
|
|
|
|
|
|
| |
this fixes the mpc85xx build error
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41477
|
|
|
|
|
|
| |
Signed-off-by: michael <igvtee@gmail.com>
SVN-Revision: 41476
|
|
|
|
|
|
| |
Signed-off-by: michael <igvtee@gmail.com>
SVN-Revision: 41475
|
|
|
|
|
|
|
|
|
|
| |
New make target in lantiq to use UbinizeImage and SysupgradeNand.
Only enabled for BTHOMEHUBV2B for the moment but should be useable
for other lantiq nand boards.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41474
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41472
|
|
|
|
|
|
|
|
| |
this broke CONFIG_ALL builds for mt7620
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41471
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41455
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41454
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41453
|
|
|
|
|
|
|
|
|
| |
After r41444 wifi working on WRTnode. Tested.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41452
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for the MikroTik RouterBOARD SXT Lite.
The new RB911L series is also supported as a result.
v2 of this patch fixes the wmac offset to match what is on the sticker.
v3 refreshes the patch against r41148 and defines the power led as the status led in diag.sh
v4 refreshes the patch against r41353 and fixes the patch path issue to make git am work correctly
v5 selects the kernel config option in the mikrotik profile rather than in the main ar71xx config
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41450
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Enable LANTIQ_PHY and LANTIQ_XRX200 only in XRX200 subtarget.
These drivers are not needed for ASE, Danube and AR9.
As side effect PHY11G and PHY22F firmwares are not included in the
kernel image, which saves 64 KB.
Signed off by: José Vázquez Fernández <ppvazquezfer@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41449
|
|
|
|
|
|
| |
Signed-off-by: Xiongfei Guo <xfguo@credosemi.com>
SVN-Revision: 41448
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41447
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41446
|
|
|
|
|
|
|
| |
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41445
|
|
|
|
|
|
| |
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41444
|
|
|
|
|
|
| |
Signed-off-by: Roman Yeryomin <roman@advem.lv>
SVN-Revision: 41443
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 41436
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 41435
|
|
|
|
|
|
| |
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
SVN-Revision: 41433
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Livebox 1 support is currently broken. Fixed with this patch
Fixes:
- Redboot partitioning broken: fixed
- Replaced custom ephy reset with platform code
- USB code breaks the building process: fixed
- Led colors
- Removed unneded EHCI code since bcm6348 only has OHCI
Signed-off-by: Daniel Gonzalez <dgcbueu@gmail.com>
[jogo: drop unneded parts since merge, fixup to apply to current head]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41424
|
|
|
|
|
|
|
|
| |
There have been no reported regressions, so backport it to 3.10.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41422
|