aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ath79: align GL-AR750S boardname to other GL.iNet devicesChristoph Krapp2019-01-014-10/+7
| | | | | | As the official device name is GL-AR750S, rename the board accordingly. Signed-off-by: Christoph Krapp <achterin@googlemail.com>
* apm821xx: sata: boot-part feature integrationChristian Lamparter2019-01-012-4/+5
| | | | | | | | | | | | This patch adds the boot-part feature to the apm82181 sata target. This makes it possible to configure the boot partition size with the generic CONFIG_TARGET_KERNEL_PARTSIZE symbol. Please note: For people using custom images: Just like with CONFIG_TARGET_ROOTFS_PARTSIZE changing the value can cause sysupgrade to repartition the device! Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: use bin file extension for sysupgrade-tar imagesChristian Lamparter2019-01-011-8/+8
| | | | | | | Use the file extension bin for sysupgrade-tar images with metadata to unify the file extension across the target/tree. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: utilize build ARTIFACTsChristian Lamparter2019-01-011-3/+5
| | | | | | | | | | | The exported kernel dtbs can be build as artifacts. This way, the MyBook Live's DTB is not generated twice. While at it, give the artifacts their proper name. For the wndr4700 use the "device-tree" partition name and for the MyBook Live: "apollo3g.dtb" to match the mbl_boot.scr. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: add support for Buffalo WXR-2533DHPINAGAKI Hiroshi2019-01-019-3/+624
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
* ipq806x: add ramdisk featureINAGAKI Hiroshi2019-01-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commits adds the "ramdisk" feature to ipq806x target. The main driving force behind this decision is to facilitate the installation of OpenWrt on some locked IPQ806x devices. Examples: - NEC Aterm WG2600HP The U-Boot on WG2600HP is protected with a password which prevents users from gaining access to the u-boot prompt in order to install the images from there. Therefore, on this device, installing OpenWrt by the user involves changing the bootcmd as follows so that WG2600HP downloads and executes initramfs image from TFTP server. ex.: bootcmd="ping ${serverip} && tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" - Buffalo WXR-2533DHP The U-Boot on WXR-2533DHP has built-in firmware recovery mode. It's activated by holding the "AOSS" button during boot. This will trigger the device to download the firmware from an TFTP server and booting from it. By using this, the user can the install OpenWrt firmware without having access to the UART console. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* kernel: Add missing symbols to 4.19Christian Lamparter2019-01-011-0/+1
| | | | | | Tested with apm82181 and ipq40xx minimal image versions. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: fix case statement in 01_ledsPaul Wassi2019-01-011-0/+1
| | | | | | Fix a missing 'end-of-case' recently introduced in 01_leds Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: rework elecom-header recipeMathias Kresin2018-12-311-26/+22
| | | | | | | | Replace the code with a more readable version. Rename the recipe to reflect the real usecase. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix spaces vs. tabsPaul Wassi2018-12-312-4/+4
| | | | | | Fix spaces vs. tabs issues in ath79 and ramips. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: tweak the position of factory partition for wr818Rosy Song2018-12-311-8/+8
| | | | | | | | The 'factory' partition will move to 0x50000-0x60000 in 2019. As the webserver in bootloader is compatible with different mtdlayout, all the users still can upgrade firmware whatever on ath79 or ar71xx. Signed-off-by: Rosy Song <rosysong@rosinson.com>
* ath79: add support for COMFAST CF-E110NRoger Pueyo Centelles2018-12-313-0/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the COMFAST CF-E110N, an outdoor wireless CPE with two Ethernet ports and a 802.11bgn radio. Specifications: - 650/400/216 MHz (CPU/DDR/AHB) - 2x 10/100 Mbps Ethernet, both with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, up to 26 dBm - 11 dBi built-in antenna - POWER/LAN/WAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. Settings from the original firmware will be saved and restored on the new want, so a factory reset will be needed: once the new firmware is flashed, perform the factory reset by pushing the reset button several times during the boot process, while the WAN LED flashes, until it starts flashing quicker. The U-boot bootloader contains a recovery HTTP server to upload the firmware. Push the reset button while powering the device on and keep it pressed for >10 seconds. The recovery page will be at http://192.168.1.1 Notes: The device is advertised, sold and labeled as "CF-E110N", but the bootloader and the stock firmware identify it as "v2". Acknowledgments: Petr Štetiar <ynezz@true.cz> Sebastian Kemper <sebastian_ml@gmx.net> Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> [drop unused labels from devicetree source file] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add support for TP-Link Archer C6 v2Georgi Vlaev2018-12-316-1/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6 v2 (EU) Hardware specification: - SOC: Qualcomm QCA9563 @ 775MHz - Flash: GigaDevice GD25Q64CSIG (8MiB) - RAM: Zentel A3R1GE40JBF (128 MiB DDR2) - Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: - 2.4GHz (bgn) QCA9563 integrated (3x3) - 5GHz (ac) Qualcomm QCA9886 (2x2) - Button: 1x power, 1x reset, 1x wps - LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps - UART: There's no UART header on the board Flash instructions: Upload openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin via the router Web interface. Flash instruction using tftp recovery: 1. Connect the computer to one of the LAN ports of the router 2. Set the computer IP to 192.168.0.66 3. Start a tftp server with the OpenWrt factory image in the tftp root directory renamed to ArcherC6v2_tp_recovery.bin. 4. Connect power cable to router, press and hold the reset button and turn the router on 5. Keep the reset button pressed until the WPS LED lights up 6. Wait ~150 seconds to complete flashing According to the GPL source the non-EU variant has different GPIOs assigned to some of the LEDs and buttons. The flash layout might be different as well. The wikidevi entry for Archer A6/C6 assumes they are identical. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
* ath79: add support for EnGenius EWS511APGuan-Hong Lin2018-12-315-0/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EnGenius EWS511AP is a wireless managed wall AP with PoE support, based on Qualcomm/Atheros QCA9531(Honeybee) + QCA9887. Short specification: - 128MB of RAM - 16 MB of SPI FLASH - 2T2R 2.4 GHz (QCA9531), 802.11b/g/n - 1T1R 5 GHz (QCA9887), 802.11ac/n/a - 2x 10/100 Mbps Ethernet (one port with PoE support) - 1x Power LED, 2x LAN LEDs, 1x WLAN 2.4G LED, 1x WLAN 5G LED - 1x RESET button - built-in watchdog chipset Flash instruction: From EnGenius firmware to OpenWrt firmware: Original firmware is based on QSDK. Use sysupgrade firmware directly in vendor GUI. Reset to factory default is necessary. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the OpenWrt firmware in the root directory on your computer. 2. Power up EWS511AP. Press 4 and then press any key to enter u-boot. 3. Download OpenWrt firmware (ath)> tftpboot 0x80060000 ${dir}"openwrt-ath79-generic-engenius_ews511ap-squashfs-sysupgrade.bin" 4. Flash the firmware (ath)> erase 0x9f060000 +f50000 (ath)> cp.b $fileaddr 0x9f060000 $filesize 5. Reboot (ath)> reset Signed-off-by: Guan-Hong Lin <GH.Lin@senao.com>
* ath79: add status LED on GL.iNet AR300MPaul Wassi2018-12-311-1/+8
| | | | | | This adds the triggers for the status LED of this device. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix boardname of GL.iNet GL-AR300MPaul Wassi2018-12-316-9/+10
| | | | | | | | | | This device is called GL-AR300M, therefore rename the board(s) to 'gl-ar300m-nor' and 'gl-ar300m-nand' Signed-off-by: Paul Wassi <p.wassi@gmx.at> [change boardname in uboot envtools as well, don't use wildcards for boardname] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: Add support for TP-Link WR810NPaul Wassi2018-12-315-1/+182
| | | | | | Device specifications given in b23b0fb28b760ce66a8f93d4681c8bd300d75d30 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: Add GL.iNet AR150 LED triggersPaul Wassi2018-12-311-0/+4
| | | | | | | When switching from ar71xx to ath79 the default netdev LED triggers for LAN and WAN got lost. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: fix boardname of GL.iNet GL-AR150Paul Wassi2018-12-313-4/+4
| | | | | | | This device is called GL-AR150, therefore rename the board to 'gl-ar150' Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for ELECOM WRC-1750GHBK2-I/CINAGAKI Hiroshi2018-12-316-138/+224
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac routers, based on Qualcomm Atheros QCA9563. This commit also includes small fix; use "0x0x03000101" as pll_1000 instead of "0x03000000". Specification: - SoC: Qualcom Atheros QCA9563 - RAM: 128 MB (DDR2) - Flash: 16 MB (SPI-NOR) - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 10/100/1000 Mbps - LED/key: 4x/3x (2x buttons, 1x slide-switch) - UART: through-hole on PCB - Vcc, RX, GND, TX from switch (QCA8337N) side - 115200n8 Flash instruction using factory image: 1. Boot WRC-1750GHBK2-I/C normaly 2. Access to "http://192.168.2.1/" and open firmware upgrade page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: Fix UBNT Unifi AC LEDsPaul Wassi2018-12-311-2/+2
| | | | | | | Both LEDs on these devices are ACTIVE_HIGH, change back to what it is on ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: Fix system LED on TP-Link WR740/741 v4Paul Wassi2018-12-311-1/+1
| | | | | | | The system LED on these devices is ACTIVE_LOW, change back to what it is on ar71xx. Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ath79: add support for TP-Link TL-WR841N/ND v8Antonio Silverio2018-12-314-0/+175
| | | | | | | | | | | | | | | | | | | CPU: Atheros AR9341 535MHz RAM: 32MB FLASH: 4MiB PORTS: 4 Port 100/10 Switch, 1 Port 100/10 Wan WiFi: Atheros AR9341 2x2:2 bgn LED: Power (static on), LAN (controlled by Switch), WAN, SYS, WiFi, RFKill BTN: WPS, WiFi, Reset Installation: Upload the factory image via the vendor-GUI. Signed-off-by: Antonio Silverio <menion@gmail.com> [resolve merge conflicts, squash commits, fix commit title, remove default default off led properties, mark sysupgrade image compatible with the ar71xx version of the board, drop blank lines from dts] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: use caldata patching for Archer C58/C59David Bauer2018-12-312-4/+1
| | | | | | | | | | | With this commit the TP-Link Archer C58 and Archer C59 use caldata patching in order to set the correct 5GHz MAC-address. Tested on TP-Link Archer C59 v1. For more details see commit 330965b. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for GL.iNet GL-AR750SChristoph Krapp2018-12-314-4/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Right now this patch adds nor image generation only. NAND image generation is not supportet at the moment. Furtheremore support for the MicroSD port is not implemented as of now. Specification: - SOC: QCA9563 (775MHz) - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR2 - Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN - Wireless: 2.4GHz (bgn) and 5GHz (ac) - USB: 1x USB 2.0 port - Button: 1x switch button, 1x reset button - LED: 3x LEDS (green) - Another LED can be accessed on GPIO 7 if soldered Flash instruction: - Set static ip to 192.168.1.2 - Unplug the power cord - Hold reset button - Plug power back in - Right led will flash 5 times - Release reset button - Browse to 192.168.1.1 - Choose sysupgrade image in NOR-flash section - Press "update nor firmware" - After successful transfer unplug network cable before device restarts Signed-off-by: Christoph Krapp <achterin@googlemail.com> [resolve merge conflicts, rename buttons, use switch input type for mode switch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix OCEDO Koala ethernet configurationDavid Bauer2018-12-301-11/+1
| | | | | | | | | The OCEDO Koala has incorrect PLL settings which result in ~3% packet loss on ethernet connections. Also omit the gmac-configuration as it's incorrect too. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add support for D-Link DIR-859 A1Weijie Gao2018-12-307-0/+223
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec of DIR-859 A1: SoC: QCA9563 DRAM: 64MB DDR2 Flash: 16MB SPI-NOR Switch: QCA8337N WiFi 5.8GHz: QCA9880 USB is supported on the PCB but not connected. Flash instructions: 1. Upgrade the factory.bin through the factory web interface or the u-boot failsafe interface. The firmware will boot up correctly for the first time. Do not power off the device after OpenWrt has booted. Otherwise the u-boot will enter failsafe mode as the checksum of the firmware has been changed. 2. Upgrade the sysupgrade.bin in OpenWrt. After upgrading completes the u-boot won't complain about the firmware checksum and it's OK to use now. 3. If you powered off the device before upgrading the sysupgrade.bin, just upgrade the factory.bin through the u-boot failsafe interface and then goto step 2. Signed-off-by: Weijie Gao <hackpascal@gmail.com> [squash commits, use common seama recipes, sync factory image recipe with ramips version] Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: move seama commands to image-commands.mkMathias Kresin2018-12-302-23/+0
| | | | | | Move it to image-commands.mk to get rid of duplicate recipes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: sync seama image build code with ramipsMathias Kresin2018-12-301-5/+8
| | | | | | | Use the same syntax as used in the ramips target, to use common seama recipes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: consolidate seama image build codeMathias Kresin2018-12-305-57/+31
| | | | | | | | Create a common template which has the required image build code defined. Add some new variables to pass individual parts to the seama recipes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* brcm63xx: remove broken DSP platform device codeJonas Gorski2018-12-30194-754/+1062
| | | | | | There is no driver and it crashes the kernel, so just remove it. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: fix bcm6348 pinmux group selectionJonas Gorski2018-12-302-14/+12
| | | | | | | | | | The mask/shift computation used the pin group number instead of the pin number, resulting in always modifying group 4 when applying muxes, so fix it to consistently use the pin number. Fixes: 0755c2d11706 ("brcm63xx: add pinctrl support") Reported-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: VH4032N: add the SPROM fixupsDaniel Gonzalez Cabanelas2018-12-305-13/+75
| | | | | | | Add the SPROM fixups for the onboard BCM43222 wifi on the Observa VH4032N Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* brcm63xx: fix gpio hogs on gpio/pinctrl nodesJonas Gorski2018-12-302-0/+253
| | | | | | | Work around a chicken/egg issue in registration of dual gpio/pinctrl nodes. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* brcm63xx: rename switch core reset patch to 0xx as it has been acceptedJonas Gorski2018-12-302-0/+0
| | | | | | The core reset fix was accepted upstream, so move it to its right place. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ath79: Fix wrong TL-WR740N v4 switch port orderEduardo Barros2018-12-291-6/+6
| | | | | | | | | | | Fix the switch port order to have the correct order in LuCI. Fixes: FS#1469 Signed-off-by: Eduardo Barros <geadas@gmail.com> [trim commit title, add a proper commit message, add fixes tag, keep alphabetical order of the blocks] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for GeHua GHL-R-001Deng Qingfang2018-12-294-0/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | Specs SoC: MT7621AT RAM: 512MiB Flash: 32MiB MX25L25635F SPI NOR 2.4G: MT7603EN 5G: MT7612EN Ethernet: 4x GE ports (1x WAN, 3x LAN) with link status LEDs USB 3.0 LEDs: POWER, 5G WIFI, 2.4G WIFI, USB, Internet. The last two ones are controlled by GPIO UART: There are 2 UARTs (UARTLITE1/ttyS0 and UARTLITE3/ttyS1) on board. UARTLITE1 is close to LEDs, and UARTLITE3 is close to flash chip. The stock u-boot uses UARTLITE1 by default. Baud rate is 57600 Flash instruction 1. telnet 192.168.9.1 2317, username is "root" and password is "admin" One can alternatively use UART to log in 2. Put OpenWrt firmware in a FAT32 USB drive, and connect it to the router One can alternatively download the firmware via wget through Internet 3. mtd write /path/to/openwrt.bin firmware 4. reboot Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: fix MT7621 dtsiDeng Qingfang2018-12-291-2/+38
| | | | | | | Fix SysTick reg Add uartlite2 and uartlite3 nodes Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for DLINK DWR-922-E2Simon Quigley2018-12-295-1/+177
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not sure if supported, I didn't try), wireless router with QMI LTE embedded modem is based on the MT7620N SoC. Specification: * MediaTek MT7620N (580 Mhz) * 64 MB of RAM * 16 MB of FLASH * 802.11bgn radio * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * 2x external, detachable (LTE) antennas * UART header on PCB (57600 8n1) * 6x LED (GPIO-controlled) * 1x bi-color Signal Strength LED (GPIO-controlled) * 2x button * JBOOT bootloader The status led has been assigned to the dwr-922-e2:green:signalstrength (lte signal strength) led. At the end of the boot it is switched off and is available for lte operation. Works correctly also during sysupgrade operation. Installation: Apply factory image via d-link http web-gui, or via recovery interface: How to recover/revert to OEM firmware: 1.) Push and hold the reset button and turn on the power. Wait until all LEDs start rapidly blinking (~10sec.) 2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set one manually 3.) Upload original factory image via JBOOT http interface at IP 192.168.123.254 4.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. 5.) You can optionally telnet to 192.168.123.254 before or during the upload and it will report the flashing status, memory address etc. 6.) Once web UI and/or telnet says "Success", power cycle the router, or type "reboot" into the telnet session. Signed-off-by: Simon Quigley <squigley@squigley.net> [squashed commits, word wrap commit message, rename signal strenght led name to match what is used for the DWR-921-C1 since they share the led configuration, add label referenced in the aliases node] Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: fix f2fs on big endian machinesChristian Lamparter2018-12-292-0/+100
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The WD MyBook Live SquashFS images didn't work anymore due to a upstream regression in f2fs commit: 0cfe75c5b01199 ("f2fs: enhance sanity_check_raw_super() to avoid potential overflows") that got backported to 4.14.86 and landed in 4.18. by Martin Blumenstingl: |Treat "block_count" from struct f2fs_super_block as 64-bit little endian |value in sanity_check_raw_super() because struct f2fs_super_block |declares "block_count" as "__le64". | |This fixes a bug where the superblock validation fails on big endian |devices with the following error: | F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0) | F2FS-fs (sda1): Can't find valid F2FS filesystem in 1th superblock | F2FS-fs (sda1): Wrong segment_count / block_count (61439 > 0) | F2FS-fs (sda1): Can't find valid F2FS filesystem in 2th superblock |As result of this the partition cannot be mounted. | |With this patch applied the superblock validation works fine and the |partition can be mounted again: | F2FS-fs (sda1): Mounted with checkpoint version = 7c84 | |My little endian x86-64 hardware was able to mount the partition without |this fix. |To confirm that mounting f2fs filesystems works on big endian machines |again I tested this on a 32-bit MIPS big endian (lantiq) device. Hopefully, this will do until Martin's patch moved through upstream to -stable. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: fix MBL DUO SUPPORTED_DEVICES compat idChristian Lamparter2018-12-291-1/+1
| | | | | | | | The MyBook Live DUO used "wd,mybooklive-duo" as the first compatible string and not "wd_mybooklive-duo". Fixes: 9b47aa93c76 ("apm821xx: unify My Book Live Single + Duo images") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: mt7621: fix 5GHz WiFi LED on ZBT WG3526Andreas Ziegler2018-12-291-0/+4
| | | | | | This fixes the 5GHz WiFi LED which was previously not working. Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
* ath79: fix Archer A7 v5 5GHz MAC adressDavid Bauer2018-12-291-1/+1
| | | | | | | | Currently all Archer A7 v5 have the same (incorrect) MAC address. The address is currently derived from eth1 which is not present on the QCA9563. Use eth0 to get the correct MAC address. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for CreativeBox v1Weijie Gao2018-12-284-0/+187
| | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621 DRAM: 512MB DDR3 Flash: 32MB SPI-NOR WiFi 2.4GHz: MT7603 @ PCIe0 WiFi 5.8GHz: MT7612 @ PCIe1 SATA: ASM1061 @ PCIe2 Interfaces: GBE RJ45 x5 USB3.0 x1 eSATA (with USB2.0) x1 SATA x1 UART x1 I2C x1 JTAG x1 Flash instructions: Through factory bootloader or firmware web interface Signed-off-by: Weijie Gao <hackpascal@gmail.com>
* ramips: add SPDX license identifier into some dts,dtsiNOGUCHI Hiroshi2018-12-283-0/+3
| | | | | | Acked-by: Mathias Kresin <dev@kresin.me> Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
* apm821xx: switch MyBook Live's recovery images to multi-fileChristian Lamparter2018-12-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch converts the MyBook Live's recovery image to utilize the multi-image method which integrates the device-tree binary directly into the image. The new initramfs can be loaded through the MyBook Live's U-boot in the following way: => setenv ipaddr 192.168.1.1 => setenv serverip 192.168.1.2 => sata init; run addtty; tftp $kernel_addr_r wd_mybooklive-initramfs.bin; bootm Waiting for PHY auto negotiation to complete... done ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) Using ppc_4xx_eth0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.1 Filename 'wd_mybooklive-initramfs.bin'. Load address: 0x1000000 Loading: ################################################ [...] done [...] Booting kernel from Legacy Image at 01000000 ... Image Name: initramfs Image Type: PowerPC Linux Multi-File Image (gzip compressed) [...] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: 4.14: switch to upstream dw-dma-hport patchChristian Lamparter2018-12-273-25/+166
| | | | | | | | | | This patch fixes the build regression on 4.14 build due to dt-bindings/dma/dw-dmac.h MIA. apm82181.dtsi:24:10: fatal error: dt-bindings/dma/dw-dmac.h: No such file or directory Fixes: 32141c183a28 ("apm821xx: add linux 4.19 apm821xx patches") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* brcm47xx: add support for the kernel 4.19Rafał Miłecki2018-12-2721-0/+2354
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | One patch that wasn't ported due to a lot of conflict is: 901-Revert-bcma-switch-GPIO-portions-to-use-GPIOLIB_IRQC.patch Hopefully a correct/real fix will get developed before we switch brcm47xx to the 4.14. This IS NOT ready for switching/trying/using 4.19 yet due to some DMA regression affecting bgmac: [ 0.945472] bgmac_bcma bcma0:2: Found PHY addr: 25 [ 0.954565] libphy: bcma_mdio mii bus: probed [ 0.959486] ------------[ cut here ]------------ [ 0.964387] WARNING: CPU: 0 PID: 1 at ./include/linux/dma-mapping.h:516 bgmac_enet_probe+0x1b4/0x5c4 [ 0.973751] Modules linked in: [ 0.976913] CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.9 #0 [ 0.982750] Stack : 804a0000 804597c4 00000000 00000000 80458fd8 8381bc2c 838282d4 80481a47 [ 0.991367] 8042e3ec 00000001 804d38f0 00000204 83980000 00000065 8381bbe0 6f55b24f [ 0.999975] 00000000 00000000 80520000 00002018 00000000 00000075 00000007 00000000 [ 1.008583] 00000000 80480000 000ee811 00000000 00000000 00000000 80432c00 80248db8 [ 1.017196] 00000009 00000204 83980000 803ad7b0 00000000 801feeec 00000000 804d0000 [ 1.025804] ... [ 1.028325] Call Trace: [ 1.030875] [<8000aef8>] show_stack+0x58/0x100 [ 1.035513] [<8001f8b4>] __warn+0xe4/0x118 [ 1.039708] [<8001f9a4>] warn_slowpath_null+0x48/0x64 [ 1.044935] [<80248db8>] bgmac_enet_probe+0x1b4/0x5c4 [ 1.050101] [<802498e0>] bgmac_probe+0x558/0x590 [ 1.054906] [<80252fd0>] bcma_device_probe+0x38/0x70 [ 1.060017] [<8020e1e8>] really_probe+0x170/0x2e8 [ 1.064891] [<8020e714>] __driver_attach+0xa4/0xec [ 1.069784] [<8020c1e0>] bus_for_each_dev+0x58/0xb0 [ 1.074833] [<8020d590>] bus_add_driver+0xf8/0x218 [ 1.079731] [<8020ef24>] driver_register+0xcc/0x11c [ 1.084804] [<804b54cc>] bgmac_init+0x1c/0x44 [ 1.089258] [<8000121c>] do_one_initcall+0x7c/0x1a0 [ 1.094343] [<804a1d34>] kernel_init_freeable+0x150/0x218 [ 1.099886] [<803a082c>] kernel_init+0x10/0x104 [ 1.104583] [<80005878>] ret_from_kernel_thread+0x14/0x1c [ 1.110107] ---[ end trace f441c0d873d1fb5b ]--- [ 1.114914] bgmac_bcma bcma0:2: Allocation of TX ring 0x200 failed [ 1.121215] bgmac_bcma bcma0:2: Unable to alloc memory for DMA [ 1.127626] bgmac_bcma: probe of bcma0:2 failed with error -12 [ 1.133838] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: ubnt-bullet-m-xw: Remove eth1 disabled nodePetr Štetiar2018-12-271-4/+0
| | | | | | It's redundant as eth1 is disabled by default in ath79.dtsi. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: ubnt-bullet-m-xw: Move eth0 mtd-mac-address to the common includePetr Štetiar2018-12-272-2/+4
| | | | | | | It's same for Bullet and Nanostation so far, so let's hope it's going to be the same for other boards sharing the same platform. Signed-off-by: Petr Štetiar <ynezz@true.cz>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-02 02:55:03 +0000