aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ar71xx: add metadata to wpj344 and wpj558 imagesEnrique Giraldo2017-09-101-0/+6
| | | | | | | | This adds metadata to wpj344 and wpj558 images to prevent loading firmware of wpj344 into wpj558 and vice versa. This until now was possible and break the units and had to be recovered from the uboot. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
* ar71xx: wpj558: remove unused eth1 device and fix MAC addressEnrique Giraldo2017-09-102-11/+5
| | | | Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net>
* ar71xx: add support for COMFAST CF-E355ACEnrique Giraldo2017-09-1012-0/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | COMFAST CF-E355AC is a ceiling mount AP with PoE support, based on Qualcomm/Atheros QCA9531 + QCA9882. Short specification: - 2x 10/100 Mbps Ethernet, with PoE support - 64MB of RAM (DDR2) - 16 MB of FLASH - 2T2R 2.4 GHz, 802.11b/g/n - 2T2R 5 GHz, 802.11ac/n/a - built-in 4x 3 dBi antennas - output power (max): 500 mW (27 dBm) - 1x RGB LED, 1x button - built-in watchdog chipset Flash instruction: Original firmware is based on OpenWrt. Use sysupgrade image directly in vendor GUI. Signed-off-by: Enrique Giraldo <enrique.giraldo@galgus.net> [whitespace fixes, ac radio caldata offset fix] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for GL.iNet GL-USB150Piotr Dymacz2017-09-1013-0/+121
| | | | | | | | | | | | | | | | | | | | | GL.iNet GL-USB150 is an USB dongle WiFi router, based on Atheros AR9331. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - Realtek RTL8152B USB to Ethernet bridge (connected with AR9331 PHY4) - 1T1R 2.4 GHz - 2x LED, 1x button - UART header on PCB Flash instruction: Vendor firmware is based on OpenWrt CC. GUI or sysupgrade can be used to flash LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* lantiq: ARV7519RW22: enable PCIeJorge Amorós2017-09-101-1/+2
| | | | | | | Enable PCIe to make the (still unsupported) WAVE300 wireless visible to the system. Signed-off-by: Jorge Amorós <joramar76@yahoo.es>
* lantiq: VR200v: enable PCIVittorio Alfieri2017-09-091-0/+5
| | | | | | | Enable PCI to make the (still unsupported) WAVE300 wireless visible to the system. Signed-off-by: Vittorio Alfieri <vittorio88@gmail.com>
* ramips: Archer C50v1: support US and EU versionsThibaut VARENE2017-09-091-4/+6
| | | | | | | | | | | | | | | | | For the Archer C50v1, the EU and US versions are differentiated by their respective HW additional version (0x0 for US, 0x2 for EU). The stock web interface checks this field before flashing, making it impossible to flash the current (US) factory image on EU hardware. However the bootloader does not check this field, making it possible to use a single sysupgrade image for both hardware. This patch adds the necessary build bits to generate both EU and US factory images, and renames the target as "Archer C50v1" since there are as of now 3 different versions of Archer C50 (all with different CPUs). Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: add support for the HNET C108Kristian Evensen2017-09-097-0/+197
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The HNET C108 (http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a mifi based on MT7602A, which has the following specifications: * CPU: MT7620A * 1x 10/100Mbps Ethernet. * 16 MB Flash. * 64 MB RAM. * 1x USB 2.0 port. Only power is connected, this port is meant for charging other devices. * 1x mini-PCIe slots. * 1x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. * 6000 mAh battery. * 5x controllable LEDs. Works: * Wifi. * Switch. * mini-PCIe slot. Only tested with a USB device (a modem). * SIM slot. * Sysupgrade. * Button (reset). Not working (also applies to the factory firmware): * Wifi LED. It is always switched on, there is no relation to the up/down state or activity of the wireless interface. Not tested: * SD card reader. Notes: * The C108 has no dedicated status LED. I therefore set the LAN LED as status LED. Installation: The router comes pre-installed with OpenWRT, including a variant of Luci. The initial firmware install can be done through this UI, following normal procedure. I.e., access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. Recovery: If you brick the device, the C108 supports recovery using TFTP. Keep the reset button pressed for ~5sec when booting to trigger TFTP. Set the address of the network interface on your machine to 10.10.10.3/24, and rename your image file to Kernal.bin. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* kernel: rtl8306: fix port link statusMathias Kresin2017-09-081-0/+4
| | | | | | | | | | | In case the link changes from down to up, the register is only updated on read. If the link failed/was down, this bit will be 0 until after reading this bit again. Fixes a reported link down by swconfig alebit the link is up (query for the link again will show the correct link status) Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix xrx200 switch carrier stateMathias Kresin2017-09-081-4/+3
| | | | | | | | | | | | | | | | In conditions where none of the switch ports is connected during boot, the priv->port[i].link != priv->port[i].phydev->link condition is false since both link values are equal (false). The carrier of the switch netdev is never set to off and the link state reported by ip is UNKNOWN. Turn the carrier off if none of the switch ports has a link, regardless whether something has been changed. Add a check for a carrier to prevent unnecessary calls to netif_carrier_off() if the carrier is already off. Based on a patch send by Martin Schiller. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mediatek: fix mdio schedule while atomic errorJohn Crispin2017-09-071-0/+16
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: fix default LED configurationKristian Evensen2017-09-061-0/+0
| | | | | | | | | | | | | | | Commit 77645ffcd9ad ("ramips: add support for the GnuBee Personal Cloud One") dropped the execution permission from 01_leds with the result that the file isn't started during first boot and no default LED configuration is added. Revert the introduced file permission change. Fixes: FS#979 Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [cherry picked the fix from a board support patch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop kernel 4.4 supportMathias Kresin2017-09-0546-18378/+0
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: switch to kernel 4.9Edward O'Callaghan2017-09-051-1/+1
| | | | Signed-off-by: Edward O'Callaghan <funfunctor@folklore1984.net>
* kernel: update 4.4 to 4.4.86Kevin Darbyshire-Bryant2017-09-053-19/+19
| | | | | | | | Refresh patches Compile & run tested: ar71xx - Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ar71xx: WNDR4300: use the switch LED trigger on the WAN portDaniel Gonzalez Cabanelas2017-09-051-1/+2
| | | | | | | | | | The WAN port on the Netgear WNDR4300 router has two LEDs, amber and green. Use the switch LED trigger to behave as the rest of the LAN HW controlled LEDs - Green: 1 Gbps - Amber: 100/10 Mbps Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* ramips: fix mt76x8 dependenciesJohn Crispin2017-09-051-4/+4
| | | | | | | The commit merging mt7628 and mt7688 failed to update some dependencies. Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: add support for TL-WR1041N(v2) LAN/WAN LEDs.Kuang Rufan2017-09-041-1/+20
| | | | | | | | 1. Add support to LAN/WAN LEDs attached to ar8327. 2. Fix the problem that LAN/WAN LEDs does not blink in hardware (auto) mode when connected to 10M/100M ethernet. Signed-off-by: Kuang Rufan <master@a1983.com.cn>
* kernel: update 4.9 to 4.9.47Stijn Tintel2017-09-037-46/+34
| | | | | | | | Refresh patches. Compile-tested on ramips/mt7621 and x86/64. Runtime-tested on ramips/mt7621 and x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* generic: make switch_port_stats tx/rx_bytes long longThibaut VARENE2017-09-012-3/+3
| | | | | | | | | | | | | | This generic structure defines tx_bytes and rx_bytes as unsigned long (u32), while several devices would typically report unsigned long long (u64). The code can work as is, but there's a chance that with a sufficiently fast interface the overflow might happen too fast to be correctly noticed by the consumers of this data. This patch makes both field unsigned long long and updates the only known consumer of this data: swconfig_leds.c Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* generic: provide get_port_stats() on rtl836x switchesThibaut VARENE2017-09-016-0/+74
| | | | | | | | | | This patch provides a generic switch_dev_ops 'get_port_stats()' callback by taping into the relevant port MIB counters. This callback is used by swconfig_leds led trigger to blink LEDs with port network traffic. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* generic: provide get_port_stats() on b53 switchesThibaut VARENE2017-09-011-1/+57
| | | | | | | | | | This patch provides a generic switch_dev_ops 'get_port_stats()' callback by taping into the relevant port MIB counters. This callback is used by swconfig_leds led trigger to blink LEDs with port network traffic. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* generic: provide get_port_stats() on adm6996 switchesThibaut VARENE2017-09-011-0/+32
| | | | | | | | | | This patch provides a generic switch_dev_ops 'get_port_stats()' callback by taping into the relevant port MIB counters. This callback is used by swconfig_leds led trigger to blink LEDs with port network traffic. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* generic: provide get_port_stats() on ar8xxx switchesThibaut VARENE2017-09-013-0/+61
| | | | | | | | | | | | | This patch provides a generic switch_dev_ops 'get_port_stats()' callback by taping into the relevant port MIB counters. The implementation uses a generic callback that select the correct MIB counter index based on chip version. This callback is used by swconfig_leds led trigger to blink LEDs with port network traffic. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: provide get_port_stats() on mt7530/762x switchesThibaut VARENE2017-09-011-0/+36
| | | | | | | | | | This patch provides a generic switch_dev_ops 'get_port_stats()' callback by taping into the relevant port MIB counters. This callback is used by swconfig_leds led trigger to blink LEDs with port network traffic. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* kernel: update 4.4 to 4.4.85Kevin Darbyshire-Bryant2017-08-311-1/+1
| | | | | | | | Refresh patches Compile & run tested: ar71xx - Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* ar71xx: fix switch port numbering on RB750r2 and RB750UPr2João Chaínho2017-08-311-2/+6
| | | | | | | This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite). Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them. Signed-off-by: João Chaínho <joaochainho@gmail.com>
* ramips: merge mt7628/mt7688 into mt76x8L. D. Pinney2017-08-3010-354/+103
| | | | | | | | | | The ramips subtargets of mt7628 and mt7688 dts files all #include "mt7628an.dtsi" They are essentially a single subtarget. This patch merges the ramips subtargets mt7628 and mt7688 into a single subtarget mt76x8. Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* kernel: update 4.9 to 4.9.45Koen Vandeputte2017-08-304-19/+11
| | | | | | | | Refreshed all patches Compiled & run-tested on targets: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mediatek: various additional ethernet fixesJohn Crispin2017-08-303-24/+157
| | | | | | | | * fixes default affinity * adds a napi watchdog - we were seeing stalled TX queues * adds up/down locking Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: ACMP252: clean up device modulesDaniel Golle2017-08-291-4/+7
| | | | | | | Install kmod-rt2800-pci instead of only the rt2x00 library. Fixes missing wireless interface on AudioCodes AC-MP252. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* layerscape: do not add custom CFLAGS.Hauke Mehrtens2017-08-261-1/+0
| | | | | | The selected CFLAGS are already set by default. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm2708: bcm2710: do not activate neon-vfpv4 manuallyHauke Mehrtens2017-08-261-1/+0
| | | | | | | | Neon and vfpv4 support are activated by GCC on all ARMv8 CPUs because this is now a mandatory part of the architecture. There is not need to activate is manually. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm63xx: Add Comtrend AR-5315u supportDaniel Gonzalez Cabanelas2017-08-268-0/+217
| | | | | | | | | | | | Add support for the Comtrend AR-5315u router This a BCM6318 based board, 64 MB RAM, 16 MB SPI flash, with an onboard BCM43217 wifi, 4 ethernet ports and 1 USB host port Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com> [jonas.gorski: refreshed patch] Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ramips: refresh kernel patchesJohn Crispin2017-08-242-10/+16
| | | | | | the reordering patch fixes random kernel hangs. bug/fix was reported by MTK/WCN. Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: Archer C2600: fix switch ports numberingBaptiste Jonglez2017-08-241-1/+4
| | | | | | | The order of LAN ports shown in Luci is reversed compared to what is written on the case of the device. Fix the order so that they match. Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* ramips: make mt7621 select WEAK_REORDERING_BEYOND_LLSCJohn Crispin2017-08-241-0/+12
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: set ethernet mac address for VoCore2L. D. Pinney2017-08-231-0/+4
| | | | | | This patch sets the mac address for the VoCore2 devices. Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* ramips: add Xiaomi Mi Router 3G supportPavel Kubelun2017-08-237-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Xiaomi Mi WiFi Router 3G. Short specification: - MT7621AT + MT7603EN + 7612EN - 256MB DDR3 RAM - 128MB NAND flash - 1+2 x 1000M Ethernet - 1x USB 3.0 port - reset button - yellow, blue, red leds Installation through telnet/ssh: - copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it from LEDE download site to /tmp - switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if wgetted from LEDE download site - run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1 - run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0 - run: mtd erase kernel0 - run: reboot Originally stock firmware has following partitions: - ... - kernel0 (primary kernel image) - kernel1 (secondary kernel image, used by u-boot in failsafe routine) - rootfs0 (primary rootfs) - rootfs1 (secondary rootfs in case primary fails) - overlay (used as ubi overlay) This commit squashes rootfs0, rootfs1 and overlay partitions into 1, so it can be used by LEDE fully for package installation, resulting in 117,5MiB. This device lacks hw watchdog, so adding softdog instead (stock does the same). Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* mediatek: drop kernel dep on userland moduleJohn Crispin2017-08-231-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* imx6: add driver for temp/voltage monitoringKoen Vandeputte2017-08-181-0/+3
| | | | | | | The Gateworks System Controller (GSC) mimics a standard AD7418 device on I2C bus 0 at slave 0x29. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* imx6: refresh kernel configKoen Vandeputte2017-08-181-5/+0
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mediatek: update to latest kernel patchset from v4.13-rcJohn Crispin2017-08-1892-599/+10641
| | | | | | Signed-off-by: Muciri Gatimu <muciri@openmesh.com> Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com> Signed-off-by: John Crispin <john@phrozen.org>
* kernel: update 4.4 to 4.4.83Kevin Darbyshire-Bryant2017-08-1710-47/+29
| | | | | | | | | | | | | | | | | Refresh patches. Minor update 704-phy-no-genphy-soft-reset.patch which was partially accepted upstream. Compile-tested on ar71xx. Runtime-tested on ar71xx. Fixes the following vulnerabilities: - CVE-2017-7533 (4.4.80) - CVE-2017-1000111 (4.4.82) - CVE-2017-1000112 (4.4.82) Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk> [cleanup commit message, add compile/runtime tested] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: update 4.9 to 4.9.44Stijn Tintel2017-08-17124-1147/+364
| | | | | | | | | | | | | | | Refresh patches. Adapt 704-phy-no-genphy-soft-reset.patch. Remove brcm2708/950-0005-mm-Remove-the-PFN-busy-warning.patch. Compile-tested on brcm2708/bcm2708 and x86/64. Runtime-tested on brcm2708/bcm2708 and x86/64. Fixes the following vulnerabilities: - CVE-2017-7533 - CVE-2017-1000111 - CVE-2017-1000112 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* bcm53xx: backport DTS commits that setup USB LEDsRafał Miłecki2017-08-176-2/+428
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for the VoCore2 LiteL. D. Pinney2017-08-119-51/+125
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VoCore2 Lite uses the same PCB as the Vocore2. This patch moves the common VoCore2 parts into dtsi. Removed memory node in the device tree source file. Memory is detected automatically. http://vocore.io/ http://vonger.net/ http://vonger.cn/ Specifications: - SoC: MediaTek MT7688AN - RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H - Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG - Wireless: Built into MT7688AN with onboard IPEX connector Firmware installation: - VoCore2-Lite ships with firmware forked from OpenWrt. - Installation from the bootloader is recommended. - If using luci/sysupgrade use the -n option (do not keep settings) original firmware uses a modified proprietary MediaTek wireless driver. - The wireless is disabled by default in LEDE. - If reverting to factory firmware using the bootloader is recommended. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Tested by: Noble Pepper <noblepepper@gmail.com>
* ramips: fix WHR-1166D WAN portMathias Kresin2017-08-111-1/+1
| | | | | | | | | | | | By adding the ICPlus IP1001 phy driver an already set RGMII delay mode is reset during driver load. Set the rgmii rx delay to fix corrupt/no packages in case the WAN port negotiates to 1000MBit. Fixes: FS#670 Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix missing otg_cap on danube platformDaniel Gonzalez Cabanelas2017-08-092-29/+90
| | | | | | | | | | USB doesn't work in some danube boards because otg_cap is missing since previous changes made on the USB-dwc2 lantiq driver. Fix it. Tested on the ARV7518PW router. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* ramips: ArcherC50v1: fix wlan2g MAC addressThibaut VARENE2017-08-061-0/+2
| | | | | | | | | | By default the wlan eprom contains the generic ralink MAC which is not the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses are decremented from the ethernet MAC. This patch fixes the MAC address for wlan2g in line with OFW. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-30 23:34:19 +0000