aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix switch for Nexx devicesINAGAKI Hiroshi2018-03-171-5/+8
| | | | | | | | | | | | | | | | | There are 2 ethernet ports on Nexx WT1520 and WT3020. These ethernet ports are assigned as follows, and other ports cannot be used. - WT1520: - port0 -> lan - port4 -> wan - WT3020: - port0 -> wan - port4 -> lan I dropped ports that cannot be used. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ar71xx: add support for Ubiquiti Litebeam M5Arne Zachlod2018-03-158-0/+78
| | | | | | | | | | | | | | | | | Specification: - SoC: Atheros AR9342 - Flash: 8 MiB - RAM: 64 MiB - UART: 1x UART on PCB - 115200 8N1 - Ethernet: 1 x 100 Mbit with passive PoE (24V/0.2A) Doesn't work: * Flash via TFTP with Ubiquiti Uboot Installation via vendor firmware: - upload factory image via webinterface Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
* ipq806x: add support for Compex WPQ864Christian Mehlis2018-03-156-13/+601
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: unset uboot build by defaultMathias Kresin2018-03-152-1/+2
| | | | | | | | Initialise the UBOOT variable by default. Otherwise it will be unintended inherit to following images if set and causes an uboot build where not required. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: make mtd patches apply againHauke Mehrtens2018-03-155-27/+27
| | | | | | | | | This makes some of the mtd patches apply again after some generic patches were changed. These problems where found by build bot. Fixes: ac9bcefa3b044 ("kernel: use V10 of mtd patchset adding support for "compatible" string") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: add Cisco Meraki MR33 SupportChris Blake2018-03-1410-1/+861
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13Christian Lamparter2018-03-1410-2/+447
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ASUS RT-AC58U/RT-ACRH13. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE) NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI) ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one Reset and one WPS button LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each) Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has an unpopulated 1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the PCB right next to the connector. U-Boot Note: The ethernet driver isn't always reliable and can sometime time out... Don't worry, just retry. Access via the serial console is required. As well as a working TFTP-server setup and the initramfs image. (If not provided, it has to be built from the OpenWrt source. Make sure to enable LZMA as the compression for the INITRAMFS!) To install the image permanently, you have to do the following steps in the listed order. 1. Open up the router. There are four phillips screws hiding behind the four plastic feets on the underside. 2. Connect the serial cable (See notes above) 3. Connect your router via one of the four LAN-ports (yellow) to a PC which can set the IP-Address and ssh and scp from. If possible set your PC's IPv4 Address to 192.168.1.70 (As this is the IP-Address the Router's bootloader expects for the tftp server) 4. power up the router and enter the u-boot choose option 1 to upload the initramfs image. And follow through the ipv4 setup. Wait for your router's status LED to stop blinking rapidly and glow just blue. (The LAN LED should also be glowing blue). 3. Connect to the OpenWrt running in RAM The default IPv4-Address of your router will be 192.168.1.1. 1. Copy over the openwrt-sysupgrade.bin image to your router's temporary directory # scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp 2. ssh from your PC into your router as root. # ssh root@192.168.1.1 The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key. Once connected...: run the following commands on your temporary installation 3. delete the "jffs2" ubi partition to make room for your new root partition # ubirmvol /dev/ubi0 --name=jffs2 4. install OpenWrt on the NAND Flash. # sysupgrade -v /tmp/openwrt-sysupgrade.bin - This will will automatically reboot the router - Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix GL.iNet GL-B1300 supportMathias Kresin2018-03-144-6/+322
| | | | | | | | | | | | | | | | | | | | Rename the dts file to match the used SoC type and drop the unnecessary KERNEL_INSTALL from the image build code. Remove the fixed rootfs and kernel partitions and create an image with rootfs appended after kernel. Setup a switch portmap matching the hardware and a default network/switch configuration to make make the second lan port working. Use eth0 as lan to have it consistent accross the target. Use the power LED to indicate the boot status. Sort the SoC entries within the dts by address and use dtc labels whenever possible. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: remove block- and pagesize from FB4040David Bauer2018-03-142-24/+0
| | | | | | | | | | | | This removes the block- and pagesize from the FritzBox 4040 image description, fixing incorrectly working sysupgrade. With this commit, the default values for block- and pagesize are used. Signed-off-by: David Bauer <mail@david-bauer.net> [chunkeey@gmail.com: removed 105-mtd-nor-add-mx25l25635f.patch as well] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: OpenMesh A42 overhaulChristian Lamparter2018-03-143-88/+81
| | | | | | | | | | | Sort the soc entries in the dts by address and use dtc labels whenever possible. Adjust the DTS files, the OpenMesh A42 is actually an IPQ4018 and not an IPQ4019. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix apss cpu overclocking spamChristian Lamparter2018-03-142-2/+113
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | There's an interaction issue between the clk changes:" clk: qcom: ipq4019: Add the apss cpu pll divider clock node clk: qcom: ipq4019: remove fixed clocks and add pll clocks " and the cpufreq-dt. cpufreq-dt is now spamming the kernel-log with the following: [ 1099.190658] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 761142857 (-34) This only happens on certain devices like the Compex WPJ428 and AVM FritzBox!4040. However, other devices like the Asus RT-AC58U and Meraki MR33 work just fine. The issue stem from the fact that all higher CPU-Clocks are achieved by switching the clock-parent to the P_DDRPLLAPSS (ddrpllapss). Which is set by Qualcomm's proprietary bootcode as part of the DDR calibration. For example, the FB4040 uses 256 MiB Nanya NT5CC128M16IP clocked at round 533 MHz (ddrpllsdcc = 190285714 Hz). whereas the 128 MiB Nanya NT5CC64M16GP-DI in the ASUS RT-AC58U is clocked at a slightly higher 537 MHz ( ddrpllsdcc = 192000000 Hz). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx/ipq806x: move qcom-dwc3 usb driver to genericMathias Kresin2018-03-142-66/+0
| | | | | | | If the a kernel package exists within multiple targets an error/warning is shown. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add targetJohn Crispin2018-03-1451-0/+25706
| | | | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: drop ipq40xx supportJohn Crispin2018-03-1448-15076/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* kernel: use V10 of mtd patchset adding support for "compatible" stringRafał Miłecki2018-03-1414-272/+548
| | | | | | | | | | | | | In the commit bde5e7a632ef0 ("kernel: backport mtd implementation for "compatible" in "partitions" subnode") patches that got accepted into l2-mtd.git were backported to the kernels 4.9 and 4.14. Unfortunately there was a regression report, patches were dropped and never reached 4.16. This commit replaces these pseudo-backports with the latest version that includes regression fix and futher changes that were requested. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: mt7620n: add mdio node and disable port4 by defaultMathias Kresin2018-03-131-1/+8
| | | | | | | | | | | | | | | | | Revert the changes I applied to aa5014dd1a58 ("ramips: mt7620n: enable port 4 as EPHY by default"). The driver expects a node mdio-bus to be present, regardless of the actual node status. If the node is missing the driver fails to load with mtk_soc_eth 10100000.ethernet: no mdio-bus child node found Disable port4 by default again. If the port is enabled but not present, a "invalid port id 4" warning is shown during boot. Fixes: FS#1428 Signed-off-by: Mathias Kresin <dev@kresin.me>
* Revert "ramips: gpio: fix compilation if CONFIG_GPIO_SYSFS=n"John Crispin2018-03-131-3/+12
| | | | | | | | This reverts commit cff2dedebc665dc1d3d64d850afd0124c6d35eaa. This patch causes build issues Signed-off-by: John Crispin <john@phrozen.org>
* kernel: b53: drop support for old location of bcm47xx_nvram.hRafał Miłecki2018-03-131-3/+1
| | | | | | | | In kernels 4.0 and older that header file was located in some subdir of arch/mips/include. Target brcm47xx supports kernels 4.4 and 4.9 only so that code isn't needed anymore. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: gpio: fix compilation if CONFIG_GPIO_SYSFS=nAndré Draszik2018-03-131-12/+3
| | | | | | | | | | | | | | | If CONFIG_GPIO_SYSFS=n, compilation fails with drivers/built-in.o: In function `gpio_export_with_name': include/asm-generic/gpio.h:128: undefined reference to `__gpiod_export' This is because the stub in that case has the wrong name, _gpiod_export() - note the missing underscore (_) at the start. Fix the stub, and add the correct prototype for the real implementation. Signed-off-by: André Draszik <git@andred.net>
* swconfig: convert swdevs_lock from spinlock to mutexFelix Fietkau2018-03-121-3/+3
| | | | | | Should fix some sleep-while-atomic issues Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: merge a pending fix for HFSC warnings/slowdowns (fixes FS#1136)Felix Fietkau2018-03-119-9/+267
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: unroll MIPS r4k cache blast functionFelix Fietkau2018-03-103-7/+180
| | | | | | | | | | | Optimize the compiler output for larger cache blast cases that are common for DMA-based networking. On ar71xx, I measured a routing throughput increase of ~8% Signed-off-by: Ben Menchaca <ben.menchaca@qca.qualcomm.com> Signed-off-by: Rosen Penev <rosenp@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* sunxi: Fix B53 swconfig driver for Lamobo R1Hauke Mehrtens2018-03-101-0/+88
| | | | | | | | This reverts the changes needed for the upstream b53 DSA switch driver to use the OpenWrt b43 swconfig switch driver instead. Tested-by: TheWerthFam <thewerthfam@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: NanoPi NEO Plus2 backport Gigabit Ethernet DT nodeAntony Antony2018-03-101-3/+21
| | | | | | Kernel 4.16 commit 27d7f9297027 Signed-off-by: Antony Antony <antony@phenome.org>
* mvebu: new subtarget cortex A53Tomasz Maciej Nowak2018-03-1026-6/+1806
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit introduces new subtarget for Marvell EBU Armada Cortex A53 processor based devices. The first device is Globalscale ESPRESSObin. Some hardware specs: SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53 processor up to 1.2GHz RAM: 512MB, 1GB or 2GB DDR3 Storage: SATA interface µSD card slot with footprint for an optional 4GB EMMC 4MB SPI NOR flash for bootloader Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports Connectors: USB 3.0 USB 2.0 µUSB port connected to PL2303SA (USB to serial bridge controller) for UART access Expansion: 2x 46-pin GPIO headers for accessories and shields with I2C, GPIOs, PWM, UART, SPI, MMC, etc MiniPCIe slot Misc: Reset button, JTAG interface Currently booting only from µSD card is supported. The boards depending on date of dispatch can come with various U-Boot versions. For the newest version 2017.03-armada-17.10 no manual intervention should be needed to boot OpenWrt image. For the older ones it's necessary to modify default U-Boot environment: 1. Interrupt boot process to run U-Boot command line, 2. Run following commands: (for version 2017.03-armada-17.06 and 2017.03-armada-17.08) setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000" saveenv (for version 2015.01-armada-17.02 and 2015.01-armada-17.04) setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait" setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}" saveenv 3. Poweroff, insert SD card with OpenWrt image, boot and enjoy. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: Add subtarget for Cortex A9 buildHauke Mehrtens2018-03-104-158/+181
| | | | | | This is in preparation for adding a subtarget for the Cortex A53 later. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: add support for Turris OmniaRyan Mounce2018-03-106-3/+59
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Turris Omnia and builds an eMMC sysupgrade image in the same format as the SolidRun ClearFog. An initramfs image in the simple yet Omnia-specific 'medkit' image format is also built in order to ease the initial flashing process. Notable hardware support omissions are support for switching between SFP cage and copper PHY, and RGB LED control. Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used. Specifications: - Marvell Armada 385 1.6GHz dual-core ARMv7 CPU - 1GB DDR3 RAM - 8GB eMMC Flash - 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports) - 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN - 2x USB 3.0 - 12x dimmable RGB LEDs controlled by independent MCU - 3x Mini PCIe slots - Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz) - Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz) - Optional Quectel EC20 Mini PCIe LTE modem Flash instructions: If the U-Boot environment has been modified previously (likely manually via serial console), first use serial to reset the default environment. => env default -a => saveenv Method 1 - USB 'medkit' image w/o serial - Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS. Note that the medkit MUST be named omnia-medkit*.tar.gz - Disconnect other USB devices from the Omnia and connect the flash drive to either USB port. - Power on the Omnia and hold down the rear reset button until 4 LEDs are illuminated, then release. - Wait approximately 2 minutes for the Turris Omnia to flash itself with the temporary image, during which LEDs will change multiple times. - Connect a computer to a LAN port of the Turris Omnia with a DHCP client - (if necessary) ssh-keygen -R 192.168.1.1 - ssh root@192.168.1.1 $ mount /dev/sda1 /mnt $ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself and you can remove the flash drive. Method 2 - TFTP w/ serial - Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy dtb + zImage to your TFTP server (rename if desired) - Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server - Connect serial console and interrupt U-Boot => dhcp => setenv serverip <tftp_server_ip_here> => tftpboot 0x01000000 zImage => tftpboot 0x02000000 dtb => bootz 0x01000000 - 0x02000000 - OpenWrt will now boot from ramdisk - Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/ $ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* mvebu: generate ramdisk image by defaultRyan Mounce2018-03-091-1/+1
| | | | | | | ramdisk images must be used in the installation process for upcoming Turris Omnia support. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* mvebu: disable DSA DT nodes for boards using mvsw61xxRyan Mounce2018-03-092-1/+31
| | | | | | | | As at this commit, DSA is not enabled in the kernel config for mvebu, so these nodes have been ignored. In preparation for the first mvebu board using DSA, disable these nodes for existing boards to avoid issues. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* kernel: bump 4.9 to 4.9.86Koen Vandeputte2018-03-095-169/+22
| | | | | | | | | | - Refreshed all patches - Removed 1 patch which got upstreamed Compile tested on: ar71xx (Rocket M5, Mikrotik RB2011) Runtime tested on: ar71xx (Rocket M5, Mikrotik RB2011) Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump to version 4.14.25Kabuli Chana2018-03-0926-249/+78
| | | | | | compile/test target mvebu/rango Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
* ar71xx: fix double registration of usb host mode devices, add usb client ↵Felix Fietkau2018-03-091-17/+26
| | | | | | | | | | | support for qca955x Only register the chipidea usb device if the strapping option indicates device mode. If not, use the regular ehci platform driver. Add qca955x device mode support, tested on 8devices Rambutan. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* uml: Remove 4.4 patchesFlorian Fainelli2018-03-083-465/+0
| | | | Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* bcm53xx: include patch adding WZR-900DHP LEDs supportRafał Miłecki2018-03-072-0/+190
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* imagebuilder: remove split patch dirs from imagebuilder archiveMatthias Schiffer2018-03-071-2/+3
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* imagebuilder: reuse rootfs preparation from rootfs.mkMatthias Schiffer2018-03-071-37/+9
| | | | | | | | | | | | In addition to removing redundant code, this fixes various issues in IB-generated images that have been fixed in prepare_rootfs before, including better handling of CONFIG_CLEAN_IPKG and enabling of initscripts from FILES. We also reuse the opkg macro and remove --force-... flags that have been removed from rootfs.mk as well. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* lantiq/xrx200: add usif support to dts filesMartin Schiller2018-03-062-8/+8
| | | | | | | | The Lantiq XRX200 aka VR9 doesn't have an asc0. Instead, there is an USIF module which can either be an UART or a SPI Controller. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* ramips: mt7620n: enable port 4 as EPHY by defaultGiuseppe Lippolis2018-03-061-5/+5
| | | | | | | | | | | | According to the datasheet the mt7620n have a fixed switch configuration with 5 ephy (10/100) port. No RGMII configuration is possible. Drop the mdio node as well. Without RGMII, the mdio node doesn't make any sense Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com> [drop mdio node, enable port4 by default] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: power up ephy port 4Pawel Dembicki2018-03-062-0/+2
| | | | | | | | | | | In some boards port 4 of mt7620 switch is powered down in bootloader configuration as lan/wan package leak mitigation. Reset ephy port 4 to default settings to power up the port. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [clarify issue in commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: fix mii bus irq assignmentFelix Fietkau2018-03-042-3/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove pdata->fifo_cfg*Felix Fietkau2018-03-043-56/+3
| | | | | | The values are the same for all chipsets that use it Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 4.4 to 4.4.119Stijn Segers2018-03-0327-145/+126
| | | | | | | | | | | | | | | | | | This bumps the 4.4. kernel in master to 4.4.119. Includes more Meltdown & Spectre mitigation. * Refresh patches. * Refresh x86/config for RETPOLINE. * Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream) * Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream) * Deleted 650-pppoe_header_pad.patch (does not apply anymore (code was replaced)). Bumps from 4.4.112 to 4.4.115 were handled by Kevin Darbyshire-Bryant. Compile-tested on: ar71xx & oxnas. Signed-off-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Rosen Penev <rosenp@gmail.com>
* kernel: bump 4.9 to 4.9.85Magnus Kroken2018-03-0324-68/+27
| | | | Signed-off-by: Magnus Kroken <mkroken@gmail.com>
* kernel: generic: Add kernel configuration optionsHauke Mehrtens2018-03-021-1/+10
| | | | | | These options are needed for the mvebu arm64 target. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.14 to 4.14.23Stijn Segers2018-03-0217-185/+29
| | | | | | | | | | | | | This patch bumps the 4.14 kernel to .23. - Refreshed patches. - Deleted bcm53xx/patches-4.14/089-PCI-iproc-Fix-NULL-pointer-dereference-for-BCMA.patch. Has been accepted upstream. - Deleted generic/pending-4.14/821-usb-Remove-annoying-warning-about-bogus-URB.patch. The upstream URB code was changed, the patch no longer applies. I discussed this with the patch author and removed it for now, we'll see how it goes. Compile-tested on: ramips/mt7621, x86/64 Run-tested on: ramips/mt7621, x86/64 Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* mvebu: base-files: moving on from net-toolsTomasz Maciej Nowak2018-03-021-4/+4
| | | | | | | Remove dependency on net-tools, replacing calls to ifconfig with iproute equivalent, in functions changing interface MAC addresses. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: rename clearfog sysupgrade script and functionsTomasz Maciej Nowak2018-03-022-5/+5
| | | | | | | | Cosmetic name change of ClearFog sysupgrade script and its functions to more generic sdcard. This way it won't be confusing for other future device additions. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: remove fs declaration in mount commandsTomasz Maciej Nowak2018-03-022-2/+3
| | | | | | | Allows to have other file system for boot partition without breaking sysupgrade. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: unify boot.scr creationTomasz Maciej Nowak2018-03-023-13/+8
| | | | | | | Unify boot.scr generation so Makefile for device image generation won't grow without a reason. Also make boot-scr step optional. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: make sdcard bootloader option configurableTomasz Maciej Nowak2018-03-022-10/+21
| | | | | | | Remove the necessity for boot loader from SD card image creation process and make it configurable. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 00:49:27 +0000