aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* ath79: led-resets: add default-trigger propertyJohann Neuhauser2018-06-161-1/+4
| | | | | | | | | Add support for the common led property "linux,default-trigger". It allows to set a default led trigger via devicetree. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de> [add commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix usb led on wr-1043nd-v1Lucian Cristian2018-06-162-10/+1
| | | | | | | usb port was not triggered correctly also remove uneded wifi led trigger from the script Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: fixup TL-WR703N/TL-MR10U splitAlex Maclean2018-06-163-19/+13
| | | | | | | | | | | Readd SoC compatible strings and correct model names mangled in a51078f7354fac9e31f6956cbddc77aaef02c67b, cleanup dts to remove duplication, rename dtsi for clarity, use correct GPIO for TL-MR10U USB power. Tested only on TL-WR703N due to lack of a TL-MR10U. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: add support for TP-Link TL-WR842N v5Maxim Anisimov2018-06-166-1/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - USB 2.0 Port - UART (J1) header on PCB (115200 8n1) - 7x LED, 2x button, power input switch Flash instruction: The only way to flash OpenWrt image in wr842nv5 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: use phytpt trigger for mt76 wirelessDavid Bauer2018-06-161-4/+4
| | | | | | | | | | | | | With this change, the LED trigger is independent from the (wireless) netdev name. The (wireless) netdev name can be easiliy changed in OpenWrt and would require an update of the netdev trigger settings each time it is done. This change is (for now) applied only to MT7628 devices from TP-Link, as we only had the possibility to test this change against two of those devices, namely a TL-WR841 v13 and a Archer C50 v3. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix mt7688 watchdog register base addrlbzhung2018-06-161-2/+2
| | | | | | | | | | | | | I found mt7688 watchdog not working. The watchdog registers are identical for mt7621 and mt7628/mt7688. The first watchdog related register is at 0x10000100, the last one - a 16bit sized - at 0x10000128. Set the correct register address and size in the dtsi file to get the watchdog working. Signed-off-by: lbzhung <gewalalb@gmail.com> [add commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7621: fix mtu setting with kernel 4.14Mathias Kresin2018-06-161-11/+7
| | | | | | | | | | Since kernel 4.10 commit 61e84623ace3 ("net: centralize net_device min/max MTU checking"), the range of mtu is [min_mtu, max_mtu], which is [68, 1500] by default. It's necessary to set a max_mtu if a mtu > 1500 is supported. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq-vdsl-fw: update to provide recent vectoring firmwareDaniel Golle2018-06-151-1/+1
| | | | | | | | | | | | | | Recent Speedport firmware downloads only work over HTTPS, so the user either needs to provide the already downloaded file or install ustream-ssl-* as well as ca-certificates or ca-bundle. So to get VDSL2 with vectoring on xRX200, simply run vdsl_fw_install.sh on the target and either provide the downloaded file as instructed or make sure the device is connected to the Internet and can download that HTTPS url itself. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Revert "lantiq: get rid of ltq-vdsl-fw"Daniel Golle2018-06-151-0/+1
| | | | | | This reverts commit 0938233fcdef67d969f9429a10761cc640c6d56d. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* brcm2708: move wifi calibration EEPROMs out of base-filesDaniel Golle2018-06-145-160/+3
| | | | | | | | Ship EEPROM blobs for specific supported board only and don't have them lurking around in our source tree but rather download them from @github/RPi-Distro/firmware-nonfree upstream. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* brcm2708: add brcmfmac-firmware-43455-sdio to DEFAULT_PACKAGESDaniel Golle2018-06-141-2/+2
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* brcm2708: add RPi3+ wifi calibration dataDaniel Golle2018-06-142-0/+92
| | | | | | | | Add files from https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.txt https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.clm_blob Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: fix conntrack fixup of offloaded flows on timeoutFelix Fietkau2018-06-143-9/+33
| | | | | | Fixes excessively long conntrack timeout of short lived connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix conntrack leak for flow_offload connectionsFelix Fietkau2018-06-133-28/+123
| | | | | | | This was caused by a race condition between offload teardown and conntrack gc bumping the timeout of offloaded connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: allow hardware NAT offload drivers to keep a priv pointerFelix Fietkau2018-06-131-0/+25
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: rename ethernet driver folder to the same one that upstream usesFelix Fietkau2018-06-1327-41/+0
| | | | | | | Preparation for sharing offload code with the mediatek target through generic files/ Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: avoid flow offload for connections with xfrm on the dst entry ↵Felix Fietkau2018-06-131-1/+4
| | | | | | (should fix IPSec) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 4.9 to 4.9.107Kevin Darbyshire-Bryant2018-06-094-187/+165
| | | | | | | | | Refresh patches. Compile-tested for: ar71xx Run-tested on: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* mvebu: enable SATA port multiplier supportJeremiah McConnell2018-06-091-0/+1
| | | | | | | | | | Some of the Marvell targets have functional SATA port multiplier support, which is required for multi-bay eSATA enclosures. Enable kernel support by setting CONFIG_SATA_PMP. Closes: FS#1232 and FS#547 Signed-off-by: Jeremiah McConnell <miah@miah.com>
* ramips: fix network config for ravpower wd03Matthias Badaire2018-06-091-1/+1
| | | | | | | | This device has only one ethernet port. Signed-off-by: Matthias Badaire <mbadaire@gmail.com> [add the existing eth0 as lan block, shorten commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: use Power-LED as Diag-LED on FRITZBox 4020David Bauer2018-06-092-1/+1
| | | | | | | This commit makes use of the Power-LED as Diag-LED, allowing the LED to work as a status indicator. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: fix AVM package selectionDavid Bauer2018-06-091-2/+2
| | | | | | | The AVM package selection partially broke with the addition of the FRITZ!Box 4020. This commit restores the intended behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: add tl-mr3020-v1 supportLucian Cristian2018-06-085-12/+106
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ath79: wr1043: fix DTC warningsKarl Palsson2018-06-081-1/+1
| | | | | | Use the "correct" unit name to avoid DTC warnings. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: glinet ar150: fix DTC warningsKarl Palsson2018-06-081-1/+1
| | | | | | Supply a unit name to match other .dts files and avoid DTC warnings. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: ubnt: fix DTC warningsKarl Palsson2018-06-082-12/+10
| | | | | | | Use explicit labels instead of units with no reg's to avoid DTC warnings. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: wdr4300: avoid DTC warningsKarl Palsson2018-06-081-4/+2
| | | | | | Use direct button labels to avoid dtc warnings Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: buffalo_wzr-hp-g450h: fix dtc warningsKarl Palsson2018-06-081-13/+8
| | | | | | | | Just name buttons directly, rather than abstract and then also a label. Likewise for leds. Avoids DTC warnings about unit address with no reg parameter. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: avm_fritz300e: avoid dtc warningsKarl Palsson2018-06-081-1/+1
| | | | | | Use number formats preferred by the device tree compiler Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: mdio: add address-cells and size-cells defaultsKarl Palsson2018-06-081-0/+4
| | | | | | | Eliminates warnings about relying on defaults from the device tree compiler. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: ar9330.dtsi: fix typo in USB unit nameKarl Palsson2018-06-081-1/+1
| | | | | | | | | Make the unitname match the reg address. This fixes a DTC warning. Tested that USB is still functional on an ar9331 device including this dtsi. Signed-off-by: Karl Palsson <karlp@etactica.com>
* ath79: add etactica-eg200 supportKarl Palsson2018-06-084-0/+160
| | | | | | | | | | | | | | | | | | | | Based on original ar71xx eg200 board files Tested working: * usb hub, storage and serial port * ethernet * wifi * leds * button sysupgrade from self->self passes validity checks. sysupgrade from old ar71xx->ath79 passes. (however this doesn't migrate wireless driver configs) Only unknown issue is the existance of a /sys/class/leds/ath9k-phy0, which doesn't "exist" Signed-off-by: Karl Palsson <karlp@etactica.com>
* ramips: add support for I-O DATA WN-GX300GRINAGAKI Hiroshi2018-06-086-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek MT7621S. Specification: - MT7621S (1-Core, 2-Threads) - 64 MB of RAM - 8 MB of Flash (SPI) - 2T2R 2.4 GHz - 5x 10/100/1000 Mbps Ethernet - 2x LEDs, 4x keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 115200 bps (U-Boot, OpenWrt) Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR" and place it in the TFTP directory 3. Set the IP address of the computer to 192.168.99.8, connect to the LAN port of WN-GX300GR, and start the TFTP server on the computer 4. Connect power cable to WN-GX300GR and turn on the router 5. Press "1" key on the serial console to interrupt boot process on U-Boot, press Enter key 3 times and start firmware download via TFTP 6. WN-GX300GR downloads initramfs image and boot with it 7. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for WN-GX300GR 8. Wait ~150 seconds to complete flasing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add TP-Link TL-MR10U portAdoal Xu2018-06-085-133/+172
| | | | Signed-off-by: Adoal Xu <adoalxu@gmail.com>
* ar71xx: Fix offset to WMAC address for 8devices LimaSven Eckelmann2018-06-081-3/+1
| | | | | | | | | | | | | | | | | | The ART partition of the Lima board stores exactly three mac addresses: * 0x0: eth0 * 0x6: eth1 * 0x1002: wmac The first two are correctly assigned in the mach file but the latter points to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when it doesn't find a valid mac address in the platform_data. Remove this bogus offset to the ART partition to directly load the wmac via the EEPROM data in the ART partition. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ramips: mt7621: Fix some cosmetic DTC warningsRosen Penev2018-06-081-9/+10
| | | | | | | | | | | | | | | | Node /cpus/cpu@0 has a unit name, but no reg property Node /cpus/cpu@1 has a unit name, but no reg property Node /cpuintc@0 has a unit name, but no reg property Node /cpuclock@0 has a unit name, but no reg property Node /sysclock@0 has a unit name, but no reg property Node /pcie@1e140000/pcie0 missing ranges for PCI bridge (or not a bridge) Node /pcie@1e140000/pcie0 missing bus-range for PCI bridge Node /pcie@1e140000/pcie1 missing ranges for PCI bridge (or not a bridge) Node /pcie@1e140000/pcie1 missing bus-range for PCI bridge Node /pcie@1e140000/pcie2 missing ranges for PCI bridge (or not a bridge) Node /pcie@1e140000/pcie2 missing bus-range for PCI bridge Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mmc: Add back some non-mt7621 code that staging removedRosen Penev2018-06-081-1/+17
| | | | | | | | | | This reverts commit 8a570921b5ba49a2d3824f1220e4c53809063468. This seems to have been accidentally reverted. This fixes mt7620 and mt7628. Signed-off-by: Rosen Penev <rosenp@gmail.com> Acked-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mir3g dts define usb port Vcc volt regulator GPIOKevin Darbyshire-Bryant2018-06-082-9/+14
| | | | | | | | | | | | | | | Define USB port power on/off GPO as voltage regulator type instead of exposing as a normal GPIO. The GPO is now controlled by the USB driver via the voltage regulator definition. The regulator is of fixed output type (5V for USB) hence the GPO switches power on/off to USB pin 1 (Vcc) USB port power is enabled on driver load and disabled on driver unload. Enable kernel support for fixed voltage regulator types on mt7621. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ipq40xx: flesh out MR33's pcie dts definitionsChristian Lamparter2018-06-081-0/+13
| | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix OpenMesh A62 dtc warningsChristian Lamparter2018-06-081-8/+6
| | | | | | | | | | | | | | | | | Warning (pci_bridge): Node /soc/pci@40000000/pcie@0 missing ranges for PCI bridge (or not a bridge) Warning (pci_bridge): Node /soc/pci@40000000/pcie@0 missing bus-range for PCI bridge Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 node name is not "pci" or "pcie" Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 missing ranges for PCI bridge (or not a bridge) Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 incorrect #address-cells for PCI bridge Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 incorrect #size-cells for PCI bridge Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 missing bus-range for PCI bridge Warning (unit_address_format): Failed prerequisite 'pci_bridge' Warning (pci_device_reg): Failed prerequisite 'pci_bridge' Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge' Cc: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Tested-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq40xx: fix dtc warning about /soc/ad-hoc-bus missing a unit nameChristian Lamparter2018-06-081-1/+1
| | | | | | | This patch fixes a dtc warning that shows up for every device Warning (unit_address_vs_reg): Node /soc/ad-hoc-bus has a reg or ranges property, but no unit name Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: set #size-cells to 0 to fix warningChristian Lamparter2018-06-081-1/+1
| | | | | | | | | | | qcom-ipq4018-ex6100v2.dtb: Warning (reg_format): "reg" property in /led_spi/led_gpio@0 has invalid length (4 bytes) qcom-ipq4018-ex6100v2.dtb: Warning (avoid_default_addr_size): Relying on default #size-cells value for /led_spi/led_gpio@0 Cc: Thomas Hebb <tommyhebb@gmail.com> Cc: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ar71xx: fix USB switch to mPCIE for Mikrotik rb91x boardsKoen Vandeputte2018-06-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some devices like the Mikrotik RB912 only have 1 USB port which is shared between an USB A type port, and the mini PCIe socket. Toggling a gpio selects the output to which USB is connected. Since kernel 4.9, gpio base is rounded up to a value of 32. Commit 65da6f9ca164 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that. In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32 This means that the USB toggle gpio number actually also changes from 52 to 61. But .. Some of these GPIO numbers are also used in other locations, like the boardfile. The author forgot to also change them over there. Switching the USB port to mPCIe now shows my modem is correctly discovered again: [ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform [ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3 [ 2864.062728] usb 1-1: config 1 has no interface number 1 [ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected [ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0 [ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected [ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1 [ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected [ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2 [ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device [ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11 Fixes: 65da6f9ca164 ("ar71xx: fix secondary gpio controller base values") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Cc: Robin Leblon <robin.leblon@ncentric.com> Cc: Felix Fietkau <nbd@nbd.name>
* ath79: fix qca956x SoC bootLucian Cristian2018-06-071-0/+17
| | | | | | based on old ar71xx irq.c driver Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ar71xx: add support for OCEDO KoalaDavid Bauer2018-06-0713-0/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq806x: Enlarge R7800 flash - use netgear partitionHannu Nyman2018-06-071-8/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Increase the available flash memory size in Netgear R7800 by taking into the use the unused "netgear" partition that is located after the firmware partition. Available flash space for kernel+rootfs+overlay increases by 68 MB from 32 MB to 100 MB. In a typical build, overlay space increases from 15 to 85, increasing the package installation possibilities greatly. Reverting to the OEM firmware is still possible, as the OEM firmware contains logic to initialise the "netgear" partition if its contents do not match expectations. In OEM firmware, "netgear" contains 6 UBI sub-partitions that are defined in /etc/netgear.cfg and initialisation is done by /etc/preinit Tested with Openwrt master r7093-4fdc6ca31b and OEM V1.0.2.52 Reference to forum discussion in Netgear R7800 exploration thread: https://forum.lede-project.org/t/netgear-r7800-exploration-ipq8065-qca9984/285/1118 (messages 1118-1158) Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ipq806x: Limit NR_CPUS to 2Rosen Penev2018-06-071-1/+1
| | | | | | | | | | ipq806x is all dual core processors. ipq807x is quad core. Removes this from dmesg: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: bump 4.9 to 4.9.106Koen Vandeputte2018-06-073-163/+185
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: add WLAN, Ethernet-Switch with LAN/WAN and Status LED to DorinCatrinel Catrinescu2018-06-073-6/+15
| | | | Signed-off-by: Catrinel Catrinescu <cc@80211.de>
* zynq: remove support for kernel 4.4Luis Araneda2018-06-071-752/+0
| | | | Signed-off-by: Luis Araneda <luaraneda@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 00:24:55 +0000