aboutsummaryrefslogtreecommitdiffstats
path: root/target
Commit message (Collapse)AuthorAgeFilesLines
* x86: disable CONFIG_EFI_VARSAlif M. Ahmad2018-05-181-1/+1
| | | | | | | | | | Disable CONFIG_EFI_VARS, since it suffers from sysfs limitation (no support for variable longer than 1024 bytes). kmod-fs-efivarfs is the replacement of this, which enables mounting efivarfs file system and doesn't suffer from 1024 bytes limitation. Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
* ramips: add support for YUKAI Engineering Inc. BOCCOYuheiOKAWA2018-05-185-0/+174
| | | | | | | | | | | | | BOCCO is a communication robot provided by YUKAI Engineering Inc. SoC: MT7620A MEM: 256MB Flash: 8MB NAND: 512MB (non support) Include Sound DAC and AMP. No Wired Ethernet. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
* ar71xx: WNDR3700: enable RFKILL function for Wifi buttonMichal Cieslakiewicz2018-05-181-4/+4
| | | | | | | | | | | | | | | | | Wifi button for WNDR3700 dual band routers has been renamed to "rfkill" and its emitted keycode changed to KEY_RFKILL. This allows OpenWrt/LEDE to support it 'out of the box' without additional tweaking. Until this patch, button had been sending BTN_2 keycode which was ignored by default (no action script present). To get expected behaviour of switching radios on and off, user had to manually rename/link 'rfkill' script to name 'BTN_2' in /etc/rc.button directory. This patch follows similar changes for other Netgear ar71xx routers, for example WNR2000v3. It applies cleanly to both latest trunk and 17.01 branch. Tested on WNDR3700v1. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl>
* brcm2708: add squashfs rootfs imageChristian Lamparter2018-05-186-7/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds a image with squashfs as the root filesystem. A rootfs_data partition will be generated on the first boot and placed inside the rootfs partition (just after the squashfs image). advantages: - it is possible to migrate from an existing -ext4 installation and back via sysupgrade. - existing partition layout will not be lost. - slightly smaller image size. - support for attendedsysupgrade disadvantages: - needs f2fs + tools as well. This is because fs-tools decides on the blocksize of the sdcard. So either f2fs or ext4 can get choosen as the rootfs_data filesystem (depends on the size of the root partition). - rootfs_data is placed into the rootfs partition. This makes it difficult for tools that expect a /dev/mmc0pX device. It also makes it difficult for data recovery tools since they might not expect to find a embedded partition or will be confused. For people with existing build configurations: make sure to include mkf2fs and f2fsck package into the image... Otherwise the new -squashfs image will boot of a ram-overlay and won't keep the configurations after a reboot. Cc: Álvaro Fernández Rojas <noltari@gmail.com> Cc: Paul Spooren <spooren@informatik.uni-leipzig.de> Cc: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Acked-by: Daniel Golle <daniel@makrotopia.org>
* x86: Add APU3 reference to x86 board.dKristian Evensen2018-05-182-2/+2
| | | | | | | | | | | There is a new APU-model available, APU3. The device is configured in the same way as the APU1 and APU2, so the same LED/network setup can be used. I considered changing the case to pc-engines-apu*, but I chose to follow the existing pattern and add the full board name. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* apm821xx: backport and reassign crypto4xx patchesChristian Lamparter2018-05-1813-12/+1268
| | | | | | | | | | | | | | | | | | | | This patch backports several patches that went upstream into Herbert Xu's cryptodev-2.6 tree: crypto: Use zeroing memory allocator instead of allocator/memset crypto: crypto4xx - performance optimizations crypto: crypto4xx - convert to skcipher crypto: crypto4xx - avoid VLA use crypto: crypto4xx - add aes-ctr support crypto: crypto4xx - properly set IV after de- and encrypt crypto: crypto4xx - extend aead fallback checks crypto: crypto4xx - put temporary dst sg into request ctx The older, outstanding patches from 120-wxyz series have been upstreamed as well and therefore they have been reassigned to fit into the series. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: don't select swconfig for the MR24Christian Lamparter2018-05-181-1/+1
| | | | | | | | | | The swconfig package is part of the DEFAULT_PACKAGES list in the apm821xx's nand subtarget. It's enabled by default because the MX60(W) and WNDR4700 need it for their initramfs. However the package is not necessary for the MR24's sysupgrade image, as the MR24 does not have a switch. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix ethernet on ap-dk01.1Roman Yeryomin2018-05-181-0/+25
| | | | | | | Not sure how it worked before but ethernet is disabled by default in ipq4019 dtsi. Signed-off-by: Roman Yeryomin <roman@advem.lv>
* kernel: bump 4.14 to 4.14.41Koen Vandeputte2018-05-1864-928/+255
| | | | | | | | | | | | | | | | | | | | | Refreshed all patches Dropped upstreamed patches: 522-PCI-aardvark-fix-logic-in-PCI-configuration-read-write-functions.patch 523-PCI-aardvark-set-PIO_ADDR_LS-correctly-in-advk_pcie_rd_conf.patch 525-PCI-aardvark-use-isr1-instead-of-isr0-interrupt-in-legacy-irq-mode.patch 527-PCI-aardvark-fix-PCIe-max-read-request-size-setting.patch updated patches: 524-PCI-aardvark-set-host-and-device-to-the-same-MAX-payload-size.patch 030-USB-serial-option-fix-dwm-158-3g-modem-interface.patch Added new ARM64 symbol: CONFIG_ARM64_ERRATUM_1024718 Compile-tested on: cns3xxx, imx6, mvebu (arm64), x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.100Koen Vandeputte2018-05-1834-270/+271
| | | | | | | | | | | Refreshed all patches Added new ARM64 symbol: ARM64_ERRATUM_1024718 Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* brcm63xx: Tune the network configuration for several routersDaniel Gonzalez Cabanelas2018-05-181-3/+7
| | | | | | | | - DGND3700v1: fix port numbers, they're in reverse order - FaST2704n: there is no WAN port identified as such, only 4 LAN - AD1018: configure the "FIBRE" port as WAN Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* ramips: mmc: Sync with staging driverRosen Penev2018-05-185-3417/+2693
| | | | | | | | | | | | | | Mostly whitespace cleanups. Some unneeded code was removed. MMC init was also moved to the probe function as in 6069bdd The cleanup commits are over 100, making it hard to do them individually. Tested on GnuBee PC1 with an SD card being used as swap. Signed-off-by: Rosen Penev <rosenp@gmail.com> v2: Fixed compile issue with mt7620
* ath79: remove unused copy-file build stepMatthias Schiffer2018-05-171-3/+0
| | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ath79: fix TP-Link TL-WR1043ND v1 image buildMatthias Schiffer2018-05-173-4/+16
| | | | | | | | Both initramfs and flashed images are built and boot. No Ethernet, no WLAN, probably further issues, so the image is not added to TARGET_DEVICES for now. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* netfilter: fix hardware offload regression (FS#1551)Felix Fietkau2018-05-173-13/+13
| | | | | | | The relevant code needs to be enabled even if flow table support is only compiled as module Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: add AVM FRITZ!WLAN Repeater 300EMathias Kresin2018-05-177-0/+238
| | | | | | No known issues, everything works fine. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: ar724x: fix pll settingsMathias Kresin2018-05-171-3/+2
| | | | | | | | | | | | Add the syscon compatible, otherwise used functions like syscon_regmap_lookup_by_phandle() will return an error and setting the ethernet pll data wont work at all. Fix the pll register width. Writing to registers out of the range via syscon isn't possible and returns an error. On ar7242 the last pll register - Current Audio Modulation Logic Output - is at 0x1805003c. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add and enforce image metadataMathias Kresin2018-05-175-25/+20
| | | | | | Add metadata to images and make the metdata mandatory. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: cleanup image build codeMathias Kresin2018-05-175-1351/+24
| | | | | | | | | | Remove recipes for not yet migrated boards. Drop variables which aren't required due to the switch to devicetree like boardname. Drop the legacy image build code. Boards added to this target shouldn't use the legacy image build code anyway. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: sysupgrade: drop unused variablesMathias Kresin2018-05-171-6/+0
| | | | | | None of the variables are used at the moment. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: sysupgrade: drop unused platform checksMathias Kresin2018-05-171-171/+0
| | | | | | | None of these checks are used at the moment and most of them aren't required if the image metadata validation is used. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: sysupgrade: remove obsolete sysupgrade watchdog killMathias Kresin2018-05-171-10/+0
| | | | | | | | | The watchdog kill command was meant for busybox watchdog. Busybox watchdog was replaced by the procd watchdog mid 2013 with commit df7ce9301a25 ("busybox: disable the watchdog utility by default"), which makes the kill command obsolete since quite some time. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix dts filesMathias Kresin2018-05-1715-40/+27
| | | | | | | | | Add the SoC compatible to the individual dts files. Rename the dts files to match the common pattern. Remove dts files wich aren't used and no image in ar71xx exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: enable wirelessMathias Kresin2018-05-171-2/+0
| | | | | | PCI attached wireless works fine. So enable the wireless config symbols. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: cleanup kernel configMathias Kresin2018-05-172-6/+1
| | | | | | Remove outdated or not required kernel config settings. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: drop platform data patchesMathias Kresin2018-05-171-68/+0
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* octeontx: make board.d files executableMathias Kresin2018-05-171-0/+0
| | | | | | | Add the executable permission to the files to ensure they run on firstboot. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: make board.d files executableMathias Kresin2018-05-172-0/+0
| | | | | | | Add the executable permission to the files to ensure they run on firstboot. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: kernel 4.14: use vbus-supply devicetree propertyMathias Kresin2018-05-1725-32/+32
| | | | | | | | It isn't a phy supply, as the phy is still up if the GPIO is low. It rather is the supply for the vbus. A correct setting/definition will be relevant as soon as USB peripheral mode is supported. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: dwc2: add support for host mode external vbus supplyMathias Kresin2018-05-173-1/+165
| | | | | | | | Backport patch adding support for the vbus-supply devicetree property, which allows to specific GPIOs (via fixed regulators) to enable vbus/usb power. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: complete AVM FRITZ!Box 3370 supportMathias Kresin2018-05-178-70/+238
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rename the image and use a compatible string which indicates that only hardware revision 2 and higher is supported. It allows to use the wireless LED, as HWRev 1 uses GPIO#39 for the wireless LED and starting with HWRev 2 GPIO#35 is used for the wireless LED and GPIO#39 for IFX_GPIO_MODULE_EXTPHY_MDIO. The HWREV can be checked by connecting to the fritzbox right after power on via ftp: ftp> quote GETENV HWSubRevision Within the same HW revision 5 of the Fritz!Box 3370 different NAND flash chips are used. Usually it isn't a big deal but depending on the used NAND flash chip, the ECC calculation is done different (and incompatible of course). Boards with a Micron MT29F1G08ABADA NAND flash chip are using the NAND chip to calculate the ECC (on-die). Boards with a Hynix HY27UF081G2M NAND flash chip are doing the ECC calculation in software. Supporting both with a single DTS isn't possible. It might be possible to add a patch selecting the ECC mode dynamicaly based on the found NAND flash chip. But such a patch has no chance to get accepted upstream and most likely need to be touched with every kernel update. Instead two images are created. One for Micron NAND flash chip and one for Hynix NAND flash chip. So far no pattern is known to identify the used flash chip without opening the box. Add the power off GPIO. At least EVA version 2186 sets/keeps the GPIO as input, which will cause a reboot 30sec after power on. For boards with EVA version 2186 the installation is tricky as it has to be finished within the 30sec time frame. The EVA version can be checked by connecting to the fritzbox right after power on via ftp: ftp> quote GETENV urlader-version The ath9k eeprom/caldata is at a different and offset and stored in reverse order (from the last byte to the beginning) on the flash. Reverse the bits to bring the data into the format expected by the ath9k driver. Since the ath9k eeprom is stored in reverse order on flash, we can not use the mac address from the on flash eeprom. Get the MAC address from the tffs instead. Within the same HW revision 5 of the Fritz!Box 3370 both version of the vr9 SoC are used. During preparation of kernel 4.14 support, all devicetree source files were changed to load the vr9 v1.1 and vr9 v1.2 gphy firmware, which fixed the embedded phys for boards using the version 1.2 of the vr9 SoC. While at it, add a trigger to make use of the LAN LED. Setup the build-in switch and add a hint for LuCI two show the ports in order matching the labels on the case Add support for the second USB port and provide the volatage GPIOs. Use GPIO#21 as PCIe reset pin. The lan led is connected to GPIO#38. Name the rootfs partition ubi and remove the mtd/rootfs related kernel bootargs to use the OpenWrt autoprobing based on the partition name. Enable sysupgrade support to allow an upgrade from a running system. Since sysupgrade wasn't supported till now, drop image build code which was added to allow a sysupgrade from earlier OpenWrt versions. Build images that allow an (initial) installation via EVA bootloader. To install OpenWrt via Eva bootloader, within the first seconds after power on a ftp connection need to be established to the FRITZ!Box at 192.168.178.1 and the the following ftp commands need to be run: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote SETENV linux_fs_start 0 ftp> quote MEDIA FLSH ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-kernel.bin mtd1 ftp> put /path/to/openwrt-lantiq-xrx200-FRITZ3370-eva-filesystem.bin mtd0 Signed-off-by: Andrea Merello <andrea.merello@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: switch to kernel 4.14Mathias Kresin2018-05-17117-28894/+1
| | | | | | Use kernel 4.14 by default. Signed-off-by: Mathias Kresin <dev@kresin.me>
* Revert "ramips: mmc: Sync with staging drivers"John Crispin2018-05-155-2693/+3418
| | | | | | This reverts commit 2d401925b9bdf34de800fff57f593a3665de2a6a. Signed-off-by: John Crispin <john@phrozen.org>
* staging: mt7621-eth: fix return value check in mt7621_gsw_probe()Wei Yongjun2018-05-153-6/+6
| | | | | | | | | | In case of error, the function devm_ioremap_resource() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Fixes: f079b6406348 ("staging: mt7621-eth: add gigabit switch driver (GSW)") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* staging: mt7621-eth: fix return value check in mtk_connect_phy_node()Wei Yongjun2018-05-151-2/+2
| | | | | | | | | | In case of error, the function of_phy_connect() returns NULL pointer not ERR_PTR(). The IS_ERR() test in the return value check should be replaced with NULL test. Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* staging: mt7621-eth: fix return value check in mtk_probe()Wei Yongjun2018-05-151-1/+1
| | | | | | | | | | In case of error, the function devm_ioremap_resource() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Fixes: e3cbf478f846 ("staging: mt7621-eth: add the drivers core files") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: pci: sync with staging driverRosen Penev2018-05-151-168/+150
| | | | | | | | | | This is an amagalmation of two upstream commits dealing with whitespace and dead code removal. I'm synching instead of having two separate commits as they go out of order compared to previous commits here. Tested on GnuBee PC1. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mmc: Sync with staging driversRosen Penev2018-05-155-3418/+2693
| | | | | | | | | | | | | Mostly whitespace cleanups. Some unneeded code was removed. MMC init was also moved to the probe function as in 6069bdd0871a20b5adce8d2f677946e05a2da609 The cleanup commits are over 100, making it hard to do them individually. Tested on GnuBee PC1 with an SD card being used as swap. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: Add i2c support for mt7620nMatthias Badaire2018-05-151-0/+23
| | | | | | I2c is supported on mt7620n like on mt7620a when checking the datasheet Signed-off-by: Matthias Badaire <mbadaire@gmail.com>
* kirkwood: support for buttons in Audi and ViperAlberto Bursi2018-05-151-2/+2
| | | | | | | | | | | | Both these devices have a wps and a reset button on GPIO pins, which need kmod-gpio-button-hotplug package to work. Add this package to their default package config. Troubleshooted and tested on a Viper. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* ath79: fix gmac compatible in ar9330.dtsi and ag71xx_setup_gmac_933xJohann Neuhauser2018-05-152-2/+2
| | | | | | | | | 1. compatible property in node gmac was wrong 2. ag71xx_setup_gmac_933x should use np of gmac-config and not the pointer to gmac. gmac is only used for the reg address. Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
* mvebu: add support for WRT32X (venom)Michael Gray2018-05-1413-7/+241
| | | | | | | | | | | | | | | | | | Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM with a different flash layout and boots zImage rather than uImage. Specification: - Marvell Armada 385 88F6820 (2x 1.8GHz) - 256MB of Flash - 512MB of RAM - 2.4GHz (bgn) and 5GHz (an+ac wave 2) - 4x 1Gbps LAN + 1x 1Gbps WAN - 1x USB 3.0 and 1x USB 2.0/eSATA (combo port) Flash instruction: Apply factory image via web-gui. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
* gemini: Augment DIR-685 device tree for RTL8366RBLinus Walleij2018-05-141-1/+70
| | | | | | | This makes the ethernet and RTL8366RB come up on the D-Link DIR-685. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* gemini: create zImage for DIR-685Linus Walleij2018-05-141-3/+8
| | | | Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ramips: remove unnecessary resource details.NeilBrown2018-05-141-15/+2
| | | | | | | | These resources are extracted from devicetree, so they aren't needed here. Signed-off-by: NeilBrown <neil@brown.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: remove conditional compilation.NeilBrown2018-05-141-58/+8
| | | | | | | | | | | | | Code currently defines: and then compiles code only if they are defined. We might want to disable some of these via devicetree one day, but for now just remove the #defines and the conditions - all the code for different ports is easy to identify. Signed-off-by: NeilBrown <neil@brown.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: improve interrupt mappingNeilBrown2018-05-142-69/+14
| | | | | | | | | | | | | | As the Interrupts for the PCI adapters are listed in devicetree we shouldn't need to have them explicit in the code. The simplest way to do this is to use of_irq_parse_and_map_pci() and specify an interrupt-map which identifies the different PCI hosts by bus/slot numbers. This has the advantage that the hwirq number are mapped to virq numbers for us, so the ugly hack can go. Signed-off-by: NeilBrown <neil@brown.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: Remove redundant owner assignmentChristian Lütke-Stetzkamp2018-05-141-1/+0
| | | | | | | | | Remove the owner assignment form the platform driver as platform_driver_register() already initializes the owner. Found using coccinelle. Signed-off-by: Christian Lütke-Stetzkamp <christian@lkamp.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ramips: Move PCI driver to files directoryRosen Penev2018-05-142-842/+837
| | | | | | This will make it easier to port upstream code. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* at91: sama5d4: fix bad mkubifs optionsJo-Philipp Wich2018-05-131-1/+1
| | | | | | | | | | | Drop the "-x lzo" compression type override from MKUBIFS_OPTS since we do not support it in mkfs.ubifs. Attempting to use LZO compression results in "Error: bad compressor name". The build system also appends an explicit "--compr=zlib" to the mkfs command line, turning the "-x" flag into a no-op anyway. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 23:41:57 +0000