aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ralink: more esw_rt3050 fixesJohn Crispin2016-01-021-0/+48
| | | | | | | | the IRQ was not setup properly causing an oops Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 48064
* bcm53xx: switch to simpler devm_gpiod_get in USB driverRafał Miłecki2016-01-022-0/+48
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 48062
* kernel: make bcm47xxpart work with TRX flashed at bad block(s)Rafał Miłecki2016-01-029-6/+306
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 48061
* kernel: drop bcm47xxpart patch for XiaomiRafał Miłecki2016-01-029-111/+9
| | | | | | | | | It was never tested, most likely not working (because of le32_to_cpu) and not upstreamed. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 48060
* generic/4.4: update to 4.4-rc7Imre Kaloz2016-01-015-29/+5
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 48059
* V2 ar71xx : Add Support for the Bitmain Antrouter R1John Crispin2016-01-0112-1/+144
| | | | | | | | | | This patch adds support for the Bitmain Antrouter R1 http://wiki.openwrt.org/toh/bitmain/r1 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 48058
* lantiq: Add the xbar to vr9.dtsJohn Crispin2016-01-011-1/+5
| | | | | | | | linux 4.4 (since commit 08b3c894e56580b8ed3e601212a25bda974c3cc2 "MIPS: lantiq: Disable xbar fpi burst mode") requires that the xbar is defined in the .dts of vrx200 (VR9) SoCs. SVN-Revision: 48056
* ramips: Remove LED GPIO definitions in MQmaker WiTi device treeJohn Crispin2016-01-011-19/+0
| | | | | | | | LED's were defined wrong in the device tree file, they are hardware driven because they are connected directly to the switch chip and wireless chips respectively, thus no GPIO addresses are assigned to them. It is safe to remove them from the device tree file to stop confusion. Signed-off-by: Sebastian Careba <nitroshift@yahoo.com> SVN-Revision: 48055
* ralink: add WRTnode2 platform and led supportJohn Crispin2016-01-018-0/+168
| | | | | | Signed-off-by: xzmu <xzmu@wrtnode.com> SVN-Revision: 48049
* ledtrig-netdev: add support for renamed devicesJohn Crispin2016-01-011-2/+3
| | | | | | | | | | | The ppp0 interface is renamed after the connection is established. Due to a missing NETDEV_REGISTER event, the ledtrig-netdev isn't aware of the renamed interface and literally ignores the device (no tx/rx indication, led isn't switched off with 'ifdown wan'). Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48048
* lantiq: match default xdsl mode and default wan interfaceJohn Crispin2016-01-011-1/+5
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48047
* lantiq: convert vendorid into human readable formJohn Crispin2016-01-011-0/+67
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48046
* lantiq: add the current profile to the stats outputJohn Crispin2016-01-011-0/+30
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48045
* lantiq: TDW8980 - use devicename:colour:function led naming schemeJohn Crispin2016-01-011-1/+1
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48044
* lantiq: P2812HNUFX - move usb leds to P2812HNU-F1John Crispin2016-01-012-10/+18
| | | | | | | | | | The P2812HNU-F3 doesn't have usb leds. Only the P2812HNU-F1 has those leds. Reported-by: Sylwester Petela <sscapi@gmail.com> Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48043
* lantiq: use devicename:colour:function led naming schemeJohn Crispin2016-01-0130-372/+396
| | | | | | | | | | | | | | | | The leds of the following boards are not renamed due to lack of manuals/informations: - ARV7519PW - ARV7510PW22 - ARV4510PW The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't match the leds from the manual or pictures (e.g. there shouldn't be a wps led). Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48042
* lantiq: add support for indicating the boot state using three ledsJohn Crispin2016-01-0133-132/+189
| | | | | | | | | | | | | | The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to indicate the current boot state. This patch adds support for such cases. The existing led sequences should be the same as before. Boards which are using a led different from power (like TDW89x0) are changed to switch of the led after boot Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48041
* lantiq: use dsl led defined in DTSJohn Crispin2016-01-014-17/+20
| | | | | | | | | | | | | | | | | dsl_control (dsl_notify.sh) is the only process which is aware of the state of the atm/ptm interface. Use the dsl led exclusive for the dsl line state. On boards which don't have a distinct internet and a dsl led, let the netdev status of the atm interface trigger the shared led. Triggering the shared led according to the status of the ppp interface isn't suitable, since the led would be switched of if the ppp connection goes down, but the line is still in sync. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48040
* lantiq: use power leds defined in DTSJohn Crispin2016-01-011-15/+19
| | | | | | | | Use the power leds defined in the dts file instead of hardcoded led names. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48039
* lantiq: use default leds defined in DTSJohn Crispin2016-01-012-20/+23
| | | | | | | | | | | | | Remove all now double defined leds from the led board file. Use pppoe as default for all broadband connections, since it's the default in OpenWrt now. Rename the the wifi leds to make sure, the not applicable default values get overwritten. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48038
* lantiq: define default leds in dts filesJohn Crispin2016-01-0131-135/+371
| | | | | | | | | | - ARV7525PW: use the power led as dsl led as done by the stock firmware - FRITZ3370: use the info led as internet led - FRITZ7320: use the power led as dsl led as done by the stock firmware Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48037
* lantiq: ARV752DPW - fix dts fileJohn Crispin2016-01-011-9/+13
| | | | | | | | | | | | | | Use the same led logic and labels as the OEM firmware (red = okay, blue = failure). Add the red internet led. Remove missing usb led workaround. The workaround shouldn't be in the default configuration. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48036
* lantiq: ARV752DPW22 - fix dts fileJohn Crispin2016-01-011-22/+12
| | | | | | | | | | | No need to switch (and keep) on all leds at boot. Use the same led logic and labels as the OEM firmware (red = okay, blue = failure). Add the red internet led. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48035
* lantiq: DGN1000B - fix typo in dts fileJohn Crispin2016-01-011-1/+1
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48034
* lantiq: ARV4518PWR01* move redundant parts to dtsiJohn Crispin2016-01-013-356/+186
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48033
* lantiq: BTHOMEHUBV2B - remove missing usb led workaroundJohn Crispin2016-01-011-1/+0
| | | | | | | | The workaround shouldn't be in the default configuration. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48032
* lantiq: P2812HNUFX - move leds to dtsiJohn Crispin2016-01-013-114/+61
| | | | | | | | Beside the used labels, they are the same on both boards. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48031
* ralink: fix rt3050/5350 ethernet switch supportJohn Crispin2016-01-011-9/+19
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 48030
* ramips: set the wifi mac address to the same as LAN on witiFelix Fietkau2016-01-011-0/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48029
* ramips: add a script to fix up the broken mac address on the witi boardFelix Fietkau2016-01-012-1/+79
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48027
* kernel: fold of_get_mac_address_mtd into of_get_mac_addressFelix Fietkau2016-01-013-94/+112
| | | | | | | | This makes it easier to keep drivers in sync with upstream Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48026
* ramips: fix kernel configuration for mt7628Felix Fietkau2016-01-011-0/+6
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48025
* ramips: add missing clk_round_rate function to fix buildbot errorsFelix Fietkau2016-01-011-0/+15
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48024
* ramips: fix inverted LEDs for RE6500Felix Fietkau2016-01-011-2/+2
| | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> SVN-Revision: 48022
* ramips: add mac address assignment for eth0 on RE6500Felix Fietkau2016-01-011-0/+4
| | | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48021
* ramips: fix firmware partition sizeFelix Fietkau2016-01-011-1/+1
| | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> SVN-Revision: 48020
* ramips: fix memory size for RE6500Felix Fietkau2016-01-011-1/+1
| | | | | | Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> SVN-Revision: 48019
* imx6: images: ventana: change name of ubi outputLuka Perkov2015-12-291-3/+4
| | | | | | | | | | | | | | Change the name of the .ubi produced to strip out the word 'factory'. This is mainly due to the fact that there is no difference between the Ventana 'factory' image vs the standard image. Name changes from: openwrt-imx6-ventana-squashfs.nand-factory_<size>.ubi to openwrt-imx6-ventana-squashfs-nand_<size>.ubi Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com> SVN-Revision: 48016
* imx6: fix device-tree mac address assignment for ventana sky2/eth1Luka Perkov2015-12-282-0/+54
| | | | | | | | | | | | | | Some Ventana boards have a Marvell sky2 GigE controller as eth1 however assigning the mac address through device-tree is difficult because the PCI slot can move around depending on board configuration and slot population. To work around this we add a patch to the sky2 driver to allow accessing its mac address via a device-tree alias. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com> SVN-Revision: 48013
* imx6: add i2c retries for Ventana /dev/i2c-0Luka Perkov2015-12-281-0/+24
| | | | | | | | | | | | | | On Ventana boards the Gateworks System Controller is the only device on I2C1 (/dev/i2c-0) and it can NAK transfers if it is busy in an ADC loop. Because this is a multi-function device with several slave addresses it is best to add retries at the controller level instead of within each slave driver. This adds a patch that adds 3 retries for i2c transactions only for Ventana boards and only for I2C1 Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com> SVN-Revision: 48012
* imx6: imx: thermal: use CPU temperature grade info for thresholdsLuka Perkov2015-12-281-0/+114
| | | | | | | | | | | | | | | This is a backport of a2291badc355d58ead5c19ae0609468947416040 from thermal-soc accepted upstream. The IMX6Q/IMX6DL SoC's have a 2-bit temperature grade stored in OTP. Instead of assuming 85C for passive cooling threshold and 100C for critical base these thresholds off the thermal gade max CPU temperature: - passive threshold: max - 10C - critical threshold: max - 5C Signed-off-by: Tim Harvey <tharvey@gateworks.com> SVN-Revision: 48011
* imx6: Add pwm nodesLuka Perkov2015-12-281-0/+276
| | | | | | | | Upstream status: Accepted Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com> SVN-Revision: 48010
* imx6: ventana: add ecspi3 host controller for GW52xxLuka Perkov2015-12-281-0/+35
| | | | | | | | | | Certain board revisions of the GW52xx support an SPI host controller with a single chip-select going to an off board connector. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com> SVN-Revision: 48009
* imx6: Add 4.3 supportLuka Perkov2015-12-2812-0/+2539
| | | | | | | | | | | | | | Build and boot tested on the following hardware: * GW54xx * GW53xx * GW52xx * GW51xx * GW552x * GW551x Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com> SVN-Revision: 48008
* imx6: drop lingering filesLuka Perkov2015-12-282-1072/+0
| | | | | | | | Since 3.18 kernel support was dropped, remove lingering files. Signed-off-by: Pushpal Sidhu <psidhu@gateworks.com> SVN-Revision: 48007
* ar71xx: fix sysupgrade for wnr2200Felix Fietkau2015-12-231-1/+8
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48005
* lantiq: fix Image BuilderJohn Crispin2015-12-231-2/+1
| | | | | | Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48002
* swconfig: switch kernel PORT_LINK support to SWITCH_TYPE_LINKJohn Crispin2015-12-231-47/+4
| | | | | | | | | As explained earlier, using SWITCH_TYPE_LINK gives more flexibility, it doesn't require e.g. string parsing to read some data. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 47999
* swconfig: add SWITCH_TYPE_LINK and support sending link info to user spaceJohn Crispin2015-12-233-0/+74
| | | | | | | | | | | | | So far we were sending link data as a string. It got some drawbacks: 1) Didn't allow writing clean user space apps reading link state. It was needed to do some screen scraping. 2) Forced whole PORT_LINK communication to be string based. Adding support for *setting* port link required passing string and parting it in the kernel space. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 47997
* lantiq: fix PCI_DEVICE_ID_LANTIQ_PCIEJohn Crispin2015-12-231-10/+2
| | | | | | | | | | | | | | | It's not necessary to define PCI_* if pci_ids.h is included a few lines above. The change to pci_ids.h doesn't look intentional to me, especially since the former value is added to the top of ifxmips_fixup_pcie.c. Both changes were introduced with the kernel 4.1 support patches and were not present in the 3.18 patches. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 47996
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-19 07:31:50 +0000