aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
...
* apm821xx: add DEVICE_DTS_DIR variable, remove redundant DEVICE_VARS entryFelix Fietkau2016-07-221-1/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* apm821xx: add missing default profiles for subtargetsFelix Fietkau2016-07-223-0/+41
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* apm821xx: add support for the Netgear Centria N900 WNDR4700/WNDR4720Christian Lamparter2016-07-2217-1/+2129
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for Netgear Centria N900 WNDR4700/WNDR4720 hardware highlights: CPU: AMCC PowerPC APM82181 Rev. E at 1000 MHz (PLB=166, OPB=83, EBC=83 MHz) Security support, Boot ROM Location NAND wo/ECC 2k page (8 bits) 32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory Board: AMCC APM82181 Evaluation Board, PCIE0/SATA1, 1*USB OTG DRAM: 256 MB (ECC not enabled, 500 Mb/s, 32-bit, CL3) NAND: 128 MiB (SLC, erase size: 128 KiB, page size: 2048, OOB size: 64) ETH: Atheros AR8327N Gigabit Switch (4 x LAN, 1 x WAN) USB: 2 x 3.0 (Renesas uPD720202K8-711-BAA-A, firmware not included) SATA: 1 x SATA-II 3.5" Hard Drive Bay for HDDs (DesignWare SATA). WLAN1: Atheros AR9380 5GHz 802.11an 3:3x3 WLAN2: Atheros AR9581 2.4GHz 802.11bgn 3:3x3 SDCARD: GL827L SD/MMC/MS Flash Card Reader (on internal dwc2 USB 2.0 host) I2C: GMT G781 (i2c-0 @ 0x4d - lm90 compatible temperature sensor) TC654 (i2c-0 @ 0x1b - Dual PWM fan Speed controller) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! INFO: Since this device only has a NAND chip. I opted for going with root.squashfs in a UBI volume. There's no squashfs/jffs2 image. This target produces three images. a. netgear factory image This image can be used to flash the Netgear WNDR4700 via the firmware recovery mechanism and the web admin site. The bootloader can be instructed to do a firmware recovery via the # fw_recovery command. It will start a tftp server and listen on 192.168.1.1 (the ipaddr variable in u-boot) for incoming, binary tftp clients. The firmware recovery mechanism is also started if any of the flash content which contains the kernel, device-tree definitions or the (fake)rootfs fails to verify or load. b. sysupgrade.tar image for sysupgrade An sysupgrade will replace the entire current LEDE installation with a newer version. This does include the kernel and the ubi rootfs partition. The configuration can be carried over automatically as well if desired. simply copy the sysupgrade.tar to a the WNDR4700 running LEDE and run: root@lede:~# sysupgrade sysupgrade.tar and let it reboot. Note: The devicetree flash area is NOT updated. Until the devicetree definition is stable, this can lead to all sorts of hardware detection problems! So make sure, if you experience issues: try the fw_recovery. If you are unsure whenever this affects you: test if you can reproduce your issue with the initramfs method. As it will always have up-to-date device-tree definitions. c. initramfs image for TFTP (for development and testing) To use the initramfs method, follow the following steps: 1) Move the "lede-apm821xx-netgear-WNDR4700-initramfs-kernel.bin" file to to the root directory of your TFTP server. 2) rename it to wndr4700.bin 3) On the WNDR4700 - Hit Enter during u-boot and insert: # tftp 400000 wndr4700.bin; run addtty; bootm 400000 - This will boot the LEDE image. Note: The default tftp server is 192.168.1.7, if you want to change it: # setenv serverip 192.168.8.7; Note2: The default address for the WNDR4700 is 192.168.1.1: # setenv ipaddr 192.168.8.8; Note: Connect you tftp server on the last LAN port (not the WAN) Note: The firmware for the USB 3.0 Host chip is not included anymore. Therefore the two USB 3.0 ports will not work without the uPD7070x-firmware package installed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: lm90 add thermal sensor interface support for device treeChristian Lamparter2016-07-222-0/+453
| | | | | | | | | | | | | | From 912-hwmon-lm90-expose-to-thermal-fw-via-DT.patch: "This patch adds to lm90 temperature sensor the possibility to expose itself as thermal zone device, registered on the thermal framework. The thermal zone is built only if a device tree node describing a thermal zone for this sensor is present inside the lm90 DT node. Otherwise, the driver behavior will be the same." Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: tc654: add driver for Microchip TC654/TC655 PWM fan controllersChristian Lamparter2016-07-221-0/+1037
| | | | | | | | | | | | | | | | | | | This patch adds a hwmon driver for the Microchip TC654 and TC655 Dual SMBus PWM Fan Speed Controllers with Fan Fault detection. The chip is described in the DS2001734C Spec Document from Microchip. It supports: - Shared PWM Fan Drive for two fans - Provides RPM - automatic PWM controller (needs additional NTC/PTC Thermistors.) - Overtemperature alarm (when using NTC/PTC Thermistors) The TC654 is used by the Netgear WNDR47X0 to control its system fan. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Western Digital MyBook Live SeriesChristian Lamparter2016-07-2220-2/+1006
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware Highlights: This patch adds support for Western Digital MyBook Live Series: CPU: AMCC PowerPC UNKNOWN (PVR=12c41c83) at 800 MHz (PLB=200, OPB=100, EBC=100 MHz) 32 kB I-Cache 32 kB D-Cache, 256 kB L2-Cache, 32 kB OnChip Memory Board: Apollo-3G - APM82181 Board, 1*SATA DRAM: 256 MB (2x NT5TU64M16GG-AC) FLASH: 512 kB (SST 39VF040) Ethernet: 1xRGMII - 1 Gbit - Broadcom PHY BCM54610 WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The MyBook Live Duo additionally features a 1x USB 2.0 host port and can support a second hard-drive. This target produces two images for a target. 1. ext4 image The extracted/raw image can be directly installed on the internal HDD via "dd if=img.ext4 of=/dev/sdX". This can either be done in place with the stock MyBook Live firmware via ssh. Or by removing the HDD and writing the image with a different PC. The the compressed images are useful for sysupgrade. 2. recovery.tar image for TFTP and Serial. extract the recovery.tar to a TFTP server directory. On the MyBook Live (Duo) serial port - Hit Enter during u-boot and insert: # setenv serverip 192.168.1.254; setenv ipaddr 192.168.1.1; run net_self Where 192.168.1.254 is your TFTP server. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: sata_dwc_460ex: backport fixes and cleanups from 4.7Christian Lamparter2016-07-221-0/+1088
| | | | | | | | | | This patch fixes the sata_dwc_460ex SATA driver which is used by the SATA controllers in the MyBook Live Series and WNDR4700. The code was backported from the upstream kernel. It can be dropped completely on 4.7+. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: dw_dmac: backport fixes and cleanups from 4.7Christian Lamparter2016-07-224-0/+2303
| | | | | | | | | | This patch fixes the dw_dmac dma engine which is used by the SATA controllers in the MyBook Live Series and WNDR4700. The code was backported from the upstream kernel. It can be dropped completely on 4.7+. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: add support for the Cisco Meraki MR24Chris Blake2016-07-2215-10/+722
| | | | | | | | | | | | | | | | | | | This patch adds support for the Cisco Meraki MR24 Access point to the apm821xx target. Board: MR24 - Meraki MR24 Cloud Managed Access Point CPU: APM82181 SoC 800 MHz (PLB=200 OPB=100 EBC=100) Flash size: 32MiB RAM Size: 128MiB Wireless: Atheros AR9380 5.0GHz + Atheros AR9380 2.4GHz Ethernet ports: 1x Gigabit Atheros AR8035 WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! For flashing instructions, visit: <https://github.com/riptidewave93/Openwrt-MR24/blob/master/README.md#flashing> Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* apm821xx: add support for the apm821xx device targetChris Blake2016-07-2214-0/+1177
| | | | | | | | This adds a new target for PowerPC APM82181 and APM82161 (464-based) boards, as well as adds support for the booke-wdt watchdog package. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ppc4xx: remove booke-wdt watchdog packageChristian Lamparter2016-07-224-2/+4
| | | | | | | | This patch gets rid of the booke watchdog kmod package. Instead the affected boards will enable it in their kernel configs. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* lantiq: fix image creation of P2812HNUF3 & BTHOMEHUBV3AMathias Kresin2016-07-221-2/+2
| | | | | | | | Both devices were converted to the new image build code but still using the LegacyDevice define. Therefore an image isn't created for the mentioned devices. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: enable CONFIG_SND_PROC_FS by default (FS#54)Felix Fietkau2016-07-211-2/+2
| | | | | | Some user space code relies on it Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add missing profile for the nand subtarget (FS#56)Felix Fietkau2016-07-211-0/+18
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix WNDR4300v1 / WNDR3700v4 build (FS#56)Felix Fietkau2016-07-211-3/+9
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix more image build code whitespace/tab issuesFelix Fietkau2016-07-211-6/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: fix tab vs whitespace issue in image building codeFelix Fietkau2016-07-211-180/+180
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: remove obsolete MultiProfile template codeFelix Fietkau2016-07-211-40/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: switch to the new image build codeFelix Fietkau2016-07-216-405/+127
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: update bcma backporting changes up to 4.8Rafał Miłecki2016-07-204-3/+101
| | | | | | This allows building bcm47xxsflash on ARM. Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
* kernel: backport patch for MTD_BCM47XXSFLASH dependencyRafał Miłecki2016-07-202-0/+41
| | | | | | | This is required to update bcma without build breakage. One of bcma patches changes BCMA_SFLASH dependency. Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
* ipq806x: clean up redundant initialization of core device image variablesFelix Fietkau2016-07-201-4/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* cns3xxx: remove obsolete jffs2 image build codeFelix Fietkau2016-07-201-16/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* x86: remove obsolete reference to $(PROFILE)Felix Fietkau2016-07-201-1/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mxs: unconditionally install kernel images/dtb files into rootfs (needed by ↵Felix Fietkau2016-07-202-18/+4
| | | | | | boards) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: remove obsolete code for including kernel/dtb in rootfsFelix Fietkau2016-07-201-45/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* omap: remove obsolete code for including kernel/dtb in rootfsFelix Fietkau2016-07-201-11/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* omap: remove obsolete kernel version supportFelix Fietkau2016-07-2012-2081/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: remove obsolete ubinize.cfg fileFelix Fietkau2016-07-201-13/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: clean up redundant variables in the image building codeFelix Fietkau2016-07-201-15/+9
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: get rid of useless ubifs/ubi option variablesFelix Fietkau2016-07-201-33/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: convert remaining xway NAND devices to new image build codeFelix Fietkau2016-07-201-65/+8
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: convert AVM xrx200 devices to new image build codeFelix Fietkau2016-07-201-10/+16
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: convert simple xrx200 devices to new image build codeFelix Fietkau2016-07-201-15/+8
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: add image build template for NAND devicesFelix Fietkau2016-07-201-0/+19
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: simplify image building codeFelix Fietkau2016-07-201-34/+3
| | | | | | | | Specifying the device profile in PROFILES is unnecessary, and for all devices the DEVICE_PROFILE variable matched the device name. Get rid of this useless variable and set DEVICE_DTS to $(1) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: fix building NAND images in default configFelix Fietkau2016-07-201-35/+22
| | | | | | Remove remaining references to $(PROFILE) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: disable jffs2 support on xrx200Felix Fietkau2016-07-202-20/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: remove obsolete patch adding usb_find_device_by_nameFelix Fietkau2016-07-203-252/+0
| | | | | | ledtrig-usbdev does not need it anymore Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ledtrig-usbdev: use upstream function for iterating USB devicesRafał Miłecki2016-07-201-5/+27
| | | | | | This will allow us to drop LEDE patch adding usb_find_device_by_name. Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
* ar71xx: fix default network config of WZR-HP-G300NH and CR3000Jo-Philipp Wich2016-07-201-2/+2
| | | | | | | | | | | The network defaults for the WZR-HP-G300NH and CR3000 models wrongly set the lan interface to a vlan tagged device while the switch was set up in untagged mode, leading to broken lan side ethernet connectivity by default. Fix the issue by emitting untagged interfaces, consistent with the switch setting on the device. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: add support for gl-ar300mZhao Gang2016-07-2011-0/+217
| | | | | | | This add initial support for gl-ar300m router. Product page: http://www.gl-inet.com/ar300m/ Signed-off-by: Zhao Gang <gang.zhao.42@gmail.com>
* x86/generic: enable CONFIG_SATA_VIAFlorian Klink2016-07-191-0/+1
| | | | This enables support for VIA SATA.
* kernel: backport cosmetic UBIFS patches to kernel 4.1Daniel Golle2016-07-192-0/+102
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: backport yet another cosmetic ubifs patchDaniel Golle2016-07-191-0/+65
| | | | | | | | | | On UBI-enabled devices using squashfs as their rootfs an error message like UBIFS error (ubi0:3 pid 1): init_constants_early: too few LEBs (12), min. is 17 was thrown while probe-mounting the rootfs which later on succeeds and thus shouldn't alert the user. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: add kmod-ledtrig-timer to default package setDaniel Golle2016-07-181-3/+3
| | | | | | It is needed for preinit/failsafe indications to work. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: use DHCP by default on ethernet interface (lan)Daniel Golle2016-07-181-1/+1
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: sync kernel config-4.1 with changes made to config-4.4Daniel Golle2016-07-181-7/+1
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: add DTB for Akitio devices in patches-4.1Daniel Golle2016-07-181-2/+3
| | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* oxnas: revert to kernel 4.1Daniel Golle2016-07-1821-2/+899
| | | | | | | | | A bug resulting in the NAND not being detected by newer kernels has kept me sleepless for months and yet I wasn't able to discover the cause. Bring back patches and files for 4.1 until this has been resolved. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-18 07:40:39 +0000