aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for NEC Aterm WF1200CRINAGAKI Hiroshi2021-06-065-5/+196
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WF1200CR is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on QCA9561. Specification: - SoC : Qualcomm Atheros QCA9561 - RAM : DDR2 128 MiB (W971GG6SB-25) - Flash : SPI-NOR 8 MiB (MX25L6433FM2I-08G) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : QCA9561 (SoC) - 5 GHz : QCA9888 - Ethernet : 2x 10/100 Mbps - Switch : QCA9561 (SoC) - LEDs/Keys : 8x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - JP1: Vcc, GND, NC, TX, RX from "JP1" marking - 115200n8 - Power : 12 VDC, 0.9 A Flash instruction using factory image (stock: < v1.3.2): 1. Boot WF1200CR normally with "Router" mode 2. Access to "http://192.168.10.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Alternate flash instruction using initramfs image (stock: >= v1.3.2): 1. Prepare the TFTP server with the IP address 192.168.1.10 and place the OpenWrt initramfs image to the TFTP directory with the name "0101A8C0.img" 2. Connect serial console to WF1200CR 3. Boot WF1200CR and interrupt with any key after the message "Hit any key to stop autoboot: 2", the U-Boot starts telnetd after the message "starting telnetd server from server 192.168.1.1" 4. login the telnet (address: 192.168.1.1) 5. Perform the following commands to modify "bootcmd" variable temporary and check the value (to ignore the limitation of available commands, "tp; " command at the first is required as dummy, and the output of "printenv" is printed on the serial console) tp; set bootcmd 'set autostart yes; tftpboot' tp; printenv 6. Save the modified variable with the following command and reset device tp; saveenv tp; reset 7. The U-Boot downloads initramfs image from TFTP server and boots it 8. On initramfs image, download the sysupgrade image to the device and perform the following commands to erase stock firmware and sysupgrade mtd erase firmware sysupgrade <sysupgrade image> 9. After the rebooting by completion of sysupgrade, start U-Boot telnetd and login with the same way above (3, 4) 10. Perform the following commands to reset "bootcmd" variable to the default and reset the device tp; run seattle tp; reset (the contents of "seattle": setenv bootcmd 'bootm 0x9f070040' && saveenv) 11. Wait booting-up the device Known issues: - the following 6x LEDs are connected to the gpio controller on QCA9888 chip and the implementation of control via the controller is missing in ath10k/ath10k-ct - "ACTIVE" (Red/Green) - "2.4GHz" (Red/Green) - "5GHz" (Red/Green) Note: - after the version v1.3.2 of stock firmware, "offline update" by uploading image by user is deleted and the factory image cannot be used - the U-Boot on WF1200CR doesn't configure the port-side LEDs on WAN/LAN and the configuration is required on OpenWrt - gpio-hog: set the direction of GPIO 14(WAN)/19(LAN) to output - pinmux: set GPIO 14/19 as switch-controlled LEDs Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: Add support for SERCOMM NA502Andreas Böhler2021-06-064-0/+228
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The SERCOMM NA502 is a smart home gateway manufactured by SERCOMM and sold under different brands (among others, A1 Telekom Austria SmartHome Gateway). It has multi-protocol radio support in addition to LAN and WiFi. Note: BLE is currently unsupported. Specifications -------------- - MT7621ST 880MHz, Single-Core, Dual-Thread - MT7603EN 2.4GHz WiFi - MT7662EN 5GHz WiFi + BLE - 128MiB NAND - 256MiB DDR3 RAM - SD3503 ZWave Controller - EM357 Zigbee Coordinator MAC address assignment ---------------------- LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the OEM firmware does not enable 5GHz WiFi. Installation ------------ Attach serial console, then boot the initramfs image via TFTP. Once inside OpenWrt, run sysupgrade -n with the sysupgrade file. Attention: The device has a dual-firmware design. We overwrite kernel2, since kernel1 contains an automatic recovery image. If you get NAND ECC errors and are stuck with bad eraseblocks, try to erase the mtd partition first with mtd unlock ubi mtd erase ubi This should only be needed once. Signed-off-by: Andreas Böhler <dev@aboehler.at> [use kiB for IMAGE_SIZE] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: do not quote compatible in shell scriptsAdrian Schmutzler2021-06-063-21/+21
| | | | | | | The compatible is a literal string without any problematic characters, so there is no reason to quote it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: Add support for SheevaplugBERENYI Balazs2021-06-064-0/+102
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Globalscale SheevaPlug: * Marvell Kirkwood 88F6281 * 512 MB SDRAM * 512 MB Flash * Gigabit Network * USB 2.0 * SD slot * Serial console The device is supported in mainline uboot/linux the commit adds only some openwrt config for building an image. Installation: 1 - Update uboot: setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot u-boot.kwb nand erase 0x0 0x100000 nand write 0x800000 0x0 0x100000 reset 2 - Install OpenWRT: setenv ethaddr 00:50:43:01:xx:xx saveenv setenv ipaddr '192.168.0.111' setenv serverip '192.168.0.1' tftpboot openwrt-kirkwood-globalscale_sheevaplug-squashfs-factory.bin nand erase.part ubi nand write 0x800000 ubi 0x600000 reset Signed-off-by: BERENYI Balazs <balazs@wee.hu> Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com> [add vendor name for uboot-kirkwood, merge patches, copy to 5.10, add AUTORELEASE for uboot-kirkwood, refresh patches] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for the Wavlink WL-WN579X3Ben Gainey2021-06-064-0/+227
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | About the device ---------------- SoC: MediaTek MT7620a @ 580MHz RAM: 64M FLASH: 8MB WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 2x (RTL8211F) BTN: - WPS - Reset - Router/Repeater/AP (3-way slide-switch) LED: - WPS (blue) - 3-segment Wifi signal representation (blue) - WiFi (blue) - WAN (blue) - LAN (blue) - Power (blue) UART: UART is present as Pads with through-holes on the PCB. They are located next to the reset button and are labelled Vcc/TX/RX/GND as appropriate. Use 3.3V, 57600-8N1. Installation ------------ Using the webcmd interface -------------------------- Warning: Do not update to the latest Wavlink firmware (version 20201201) as this removes the webcmd console and you will need to use the serial port instead. You will need to have built uboot/sqauashfs image for this device, and you will need to provide an HTTP service where the image can be downloaded from that is accessible by the device. You cannot use the device manufacturers firmware upgrade interface as it rejects the OpenWrt image. 1. Log into the device's admin portal. This is necessary to authenticate you as a user in order to be able to access the webcmd interface. 2. Navigate to http://<device-ip>/webcmd.shtml - you can access the console directly through this page, or you may wish to launch the installed `telnetd` and use telnet instead. * Using telnet is recommended since it provides a more convenient shell interface that the web form. * Launch telnetd from the form with the command `telnetd`. * Check the port that telnetd is running on using `netstat -antp|grep telnetd`, it is likely to be 2323. * Connect to the target using `telnet`. The username should be `admin2860`, and the password is your admin password. 3. On the target use `curl` to download the image. e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\ wavlink_wl-wn579x3-squashfs-sysupgrade.bin`. Check the hash using `md5sum`. 4. Use the mtd_write command to flash the image. * The flash partition should be mtd4, but check /sys/class/mtd/mtd4/name first. The partition should be called 'Kernel'. * To flash use the following command: `mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>` Where mtd<n> is the Kernel partition, and <image-file> is the OpenWrt image previously downloaded. * The command above will erase, flash and then reboot the device. Once it reboots it will be running OpenWrt. Connect via ssh to the device at 192.168.1.1 on the LAN port. The WAN port will be configured via DHCP. Using the serial port --------------------- The device uses uboot like many other MT7260a based boards. To use this interface, you will need to connect to the serial interface, and provide a TFTP server. At boot follow the bootloader menu and select option 2 to erase/flash the image. Provide the address and filename details for the tftp server. The bootloader will do the rest. Once the image is flashed, the board will boot into OpenWrt. The console is available over the serial port. Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
* ath79: add support for Devolo dLAN pro 1200+ WiFi acFelix Matouschek2021-06-068-166/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Devolo dLAN pro 1200+ WiFi ac. This device is a plc wifi AC2400 router/extender with 2 Ethernet ports, has a QCA7500 PLC and uses the HomePlug AV2 standard. Other than the PLC the hardware is identical to the Devolo Magic 2 WIFI. Therefore it uses the same dts, which was moved to a dtsi to be included by both boards. This is a board that was previously included in the ar71xx tree. Hardware: SoC: AR9344 CPU: 560 MHz Flash: 16 MiB (W25Q128JVSIQ) RAM: 128 MiB DDR2 Ethernet: 2xLAN 10/100/1000 PLC: QCA75000 (Qualcomm HPAV2) PLC Uplink: 1Gbps MIMO PLC Link: RGMII 1Gbps (WAN) WiFi: Atheros AR9340 2.4GHz 802.11bgn Atheros AR9882-BR4A 5GHz 802.11ac Switch: QCA8337, Port0:CPU, Port2:PLC, Port3:LAN1, Port4:LAN2 Button: 3x Buttons (Reset, wifi and plc) LED: 3x Leds (wifi, plc white, plc red) GPIO Switch: 11-PLC Pairing (Active Low) 13-PLC Enable 21-WLAN power MACs Details verified with the stock firmware: Radio1: 2.4 GHz &wmac *:4c Art location: 0x1002 Radio0: 5.0 GHz &pcie *:4d Art location: 0x5006 Ethernet &ethernet *:4e = 2.4 GHz + 2 PLC uplink --- *:4f = 2.4 GHz + 3 Label MAC address is from PLC uplink The Powerline (PLC) interface of the dLAN pro 1200+ WiFi ac requires 3rd party firmware which is not available from standard OpenWrt package feeds. There is a package feed on github which you must add to OpenWrt buildroot so you can build a firmware image which supports the plc interface. See: https://github.com/0xFelix/dlan-openwrt (forked from Devolo and added compatibility for OpenWrt 21.02) Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.0.100 2. Download the sysupgrade image and rename it to uploadfile 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Allow 1-2 minutes for the first boot. Signed-off-by: Felix Matouschek <felix@matouschek.org> [add "plus" to compatible and device name] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* linux-firmware: update to version 20210315 and trim down broadcom FWJosef Schlehofer2021-06-061-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In there linux-firmware repository located in kernel, there were removed old broadcom firmware [1] as they seem to be likely vulnerable to KrØØk vulnerability (CVE-2019-15126), because Cypress released new versions and superseded by it. In OpenWrt, there is Makefile for cypress-firmware, which already provides the same named packages like it was in linux-firmware. For example, cypress-firmware-43455-sdio provides brcmfmac-firmware-43455-sdio [2]. Changelog between 2020118 and 20210315: 3568f96 (tag: 20210315) linux-firmware: Update firmware file for Intel Bluetooth AX210 9e96e50 linux-firmware: Update firmware file for Intel Bluetooth AX200 c8d0db5 linux-firmware: Update firmware file for Intel Bluetooth AX201 5e2a387 Merge tag 'iwlwifi-fw-2021-03-05-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware into main b0d3e31 rtw88: 8822c: Update normal firmware to v9.9.6 5a2fd63 iwlwifi: add new FWs from core59-66 release 4f54906 iwlwifi: update 9000-family firmwares 11b7607 iwlwifi: update 7265D firmware e425f76 Merge branch 'add-silabs-wf200' of github.com:jerome-pouiller/linux-firmware into main 5ecd13f Mellanox: Add new mlxsw_spectrum firmware xx.2008.2406 58fb90a linux-firmware: add frimware for mediatek bluetooth chip (MT7921) e576a1b rtw89: 8852a: add firmware v0.9.12.2 048a7cb WHENCE: add missing symlink for BananaPi M3 aa6c6e7 Add symlink for BananaPi M2 to brcmfmac43430-sdio config 58825f7 brcm: Fix Raspberry Pi 4B NVRAM file 520f71b silabs: add new firmware for WF200 f7915a0 amdgpu: add initial firmware for green sardine 80cb579 rtw88: RTL8822C: Update normal firmware to v9.9.5 b79d239 (tag: 20210208) Merge branch 'DG1-guc-huc-ADLS-dmc' of git://anongit.freedesktop.org/drm/drm-firmware into main 66970e1 Merge branch 'qcom-rb5' of https://github.com/lumag/linux-firmware into main cf6fc2b Mellanox: Add new mlxsw_spectrum firmware xx.2008.2304 391fd50 linux-firmware: add firmware for MT7921 c5e3240 rtw88: RTL8821C: Update firmware to v24.8 d33d2d8 linux-firmware: Update firmware file for Intel Bluetooth AX210 3027ae4 linux-firmware: Update firmware file for Intel Bluetooth AX200 13979c3 linux-firmware: Update firmware file for Intel Bluetooth AX201 348d8a9 i915: Add DMC v2.01 for ADL-S f33f1f7 i915: Add HuC v7.7.1 for DG1 6a422f5 i915: Add GuC v49.0.1 for DG1 df822a8 qcom: Add venus firmware files for VPU-1.0 11a1db1 qcom: Add SM8250 Compute DSP firmware e55248b qcom: Add SM8250 Audio DSP firmware da74cc6 qcom: add firmware files for Adreno a650 0578970 brcm: Link RPi4's WiFi firmware with DMI machine name. d528862 brcm: Add NVRAM for Vamrs 96boards Rock960 870b805 brcm: Update Raspberry Pi 3B+/4B NVRAM for downstream changes a28a590 cypress: Fix link direction 060ad8b cypress: Link the new cypress firmware to the old brcm files 0f0aefd brcm: remove old brcm firmwares that have newer cypress variants f580dc2 rtl_bt: Update RTL8822C BT(UART I/F) FW to 0x059A_25CB 7df2220 rtl_bt: Update RTL8822C BT(USB I/F) FW to 0x099a_7253 e79405d rtl_bt: Add firmware and config files for RTL8852A BT USB chip ef3813d rtl_bt: Update RTL8821C BT(USB I/F) FW to 0x829a_7644 646f159 (tag: 20201218) make AP6212 in bananpi m2 plus/zero work 28185ec linux-firmware: Update firmware file for Intel Bluetooth AX210 23da869 linux-firmware: Update firmware file for Intel Bluetooth AX200 2099248 linux-firmware: Update firmware file for Intel Bluetooth AX201 94de5e2 linux-firmware: Update firmware file for Intel Bluetooth 9560 27a3689 linux-firmware: Update firmware file for Intel Bluetooth 9260 5c3c4af Merge branch 'lt9611uxc' of https://github.com/lumag/linux-firmware into main aaed4a8 Merge branch 'v1.1.6' of https://github.com/irui-wang/linux_fw_vpu_v1.1.6 into main d8c9865 Merge branch 'master' of https://github.com/sampnimm/linux-firmware-BT into main 63ab3db linux-firmware: add firmware for Lontium LT9611UXC DSI to HDMI bridge 0fe0fe0 mediatek: update MT8173 VPU firmware to v1.1.6 1a08ec9 QCA : Updated firmware files for WCN3991 7455a36 Merge branch 'guc_v49' of git://anongit.freedesktop.org/drm/drm-firmware into main 7eb7fda linux-firmware: Update firmware file for Intel Bluetooth AX210 5cbf459 linux-firmware: Update firmware file for Intel Bluetooth AX210 c487f7d i915: Add GuC firmware v49.0.1 for all platforms d9ffb07 i915: Remove duplicate KBL DMC entry b362fd4 Mellanox: Add new mlxsw_spectrum firmware xx.2008.2018 bc9cd0b linux-firmware: Update AMD SEV firmware 54c797a amdgpu: add sienna cichlid firmware for 20.45 1340e9c amdgpu: update vega20 firmware for 20.45 b260c9c amdgpu: update vega12 firmware for 20.45 d683bd5 amdgpu: update vega10 firmware for 20.45 7c81cc2 amdgpu: update renoir firmware for 20.45 3619e57 amdgpu: update navi14 firmware for 20.45 68ce0fb amdgpu: update navi12 firmware for 20.45 e889b80 amdgpu: update navi10 firmware for 20.45 f4edc15 amdgpu: update raven2 firmware for 20.45 e71210f amdgpu: update raven firmware for 20.45 [1] https://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git/commit/?id=0f0aefd733f70beae4c0246edbd2c158d5ce974c [2] https://github.com/openwrt/openwrt/blob/eeda8652f1655d4f9c11e9c9f51ddcd3377d119a/package/firmware/cypress-firmware/Makefile#L124 Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* x86: add Roqos Core RC10 ethernet interfacesTomasz Maciej Nowak2021-06-061-0/+3
| | | | | | | | | | | | | | | | | | | eth0 -> single NIC (i211at) eth1 -> single NIC (i211at) -> 4-port unmanaged switch (BCM53125U) Notes UART is exposed on J4 connector, pinout starting from pin marked 1: 1. GND, 2. NC?, 3. NC?, 4. RX, 5. TX, 6. NC? baud: 115200, parity: none, flow control: none The board is setup by coreboot with UEFI. To enter setup screen hold ESC key on boot. The 5-LED multicolor matrix is attached on first I2C device named "Synopsys DesignWare I2C adapter" at address 0x60. Controlling values are stored in /opt/roqos/etc/rcLED.conf of original firmware. Remember to backup the original firmware, there are no downloadable copies. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* mvebu: armada-37xx: remove ethernet alias patchTomasz Maciej Nowak2021-06-064-20/+0
| | | | | | | | | This patch has been added with initial support for ESPRESSObin board and mistakenly it affects all boards with this SoC. Drop this patch since the aliases are now in upstream dts for ESPRESSObin. If any boards are relying on this, please add the respective alias to that board dts. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: add uboot-envtools to default packagesTomasz Maciej Nowak2021-06-062-17/+14
| | | | | | | | | | | | | | | | | | | When support for Luma WRTQ-329ACN was added, the instructions for flashing this device include using tools from uboot-envtools package. Unfortunately the OpenWrt buildroot system omits packages from DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE, CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In result the official images are without tools mentioned in the instruction. The workoround for the fashing would be installing uboot-envtools when booted with initramfs image, but not always the access to internet is available. The other method would be to issue the necesary command in U-Boot environment but some serial terminals default configuration don't work well with pasting lines longer than 80 chars. Therefore add uboot-envtools to default packages, which adds really small flash footprint to rootfs, where increased size usually is not an issue. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq806x: fix LAN and WAN port assignments on TP-Link AD7200Alex Henrie2021-06-061-1/+4
| | | | | | | | LAN port 4 was swapped with the WAN port and the remaining three LAN ports were numbered in reverse order from their labels on the case. Fixes: 1a775a4fd033 ("ipq806x: add support for TP-Link Talon AD7200") Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
* layerscape: armv8_64b: enable CONFIG_ARM_PSCI_CPUIDLEMartin Schiller2021-06-061-0/+1
| | | | | | | | Enable PSCI firmware based CPUidle driver. PSCI firmware is the standard power management control for all ARM64 based platforms. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* x86: kernel: enable Fusion-MPT SAS driverMark Carroll2021-06-062-0/+2
| | | | | | | Compile in MPT SAS driver required to mount rootfs on some VMWare systems (e.g. required for 1&1 IONOS). Signed-off-by: Mark Carroll <git@markcarroll.net>
* kernel: bump 5.4 to 5.4.124John Audia2021-06-0644-165/+166
| | | | | | | | | | | | | | | | | Manually rebased: generic/hack-5.4/662-remove_pfifo_fast.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [manual changes to ramips/patches-5.10/835-asoc-add-mt7620-support.patch] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.10 to 5.10.42Rui Salvaterra2021-06-0653-188/+146
| | | | | | | | | | Deleted (reverse-appliable): generic/pending-5.10/110-perf-jevents-fix-getting-maximum-number-of-fds.patch Manually refreshed: ramips/patches-5.10/835-asoc-add-mt7620-support.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* treewide: remove "+" sign for increment with macaddr_addAdrian Schmutzler2021-06-0512-49/+49
| | | | | | | | | | | | Many people appear to use an unneeded "+" prefix for the increment when calculating a MAC address with macaddr_add. Since this is not required and used inconsistently [*], just remove it. [*] As a funny side-fact, copy-pasting has led to almost all hotplug.d files using the "+", while nearly all of the 02_network files are not using it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: split Youku YK1 to YK-L1 and YK-L1cShiji Yang2021-06-055-12/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * Model: Youku YK-L1/L1c * CPU: MT7620A * RAM: 128 MiB * Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c) * LAN: 2* 10M/100M Ports * WAN: 1* 10M/100M Port * USB: 1* USB2.0 * SD: 1* MicroSD socket * UART: 1* TTL, Baudrate 57600 Descriptions: Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look really different, the only hardware difference between the two models is flash size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can compatible with YK-L1's firmware but it's better to split it to different models. It is easy to identify the models by looking at the label on the bottom of the device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update" to install compatible firmware, so please backup config file before system upgrade. Signed-off-by: Shiji Yang <yangshiji66@qq.com> [use more specific name for DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* bcm63xx: drop USB LEDs for Technicolor TG582N / ADB P.DG A4001NDaniele Castro2021-06-051-6/+1
| | | | | | | | | | | | | | | | Remove the USB status red and green LEDs for - ADB P.DG A4001N A-000-1A1-AX - Technicolor TG582N - Technicolor TG582N Telecom Italia After having mounted an SMD socket for the flash memory for JTAG reverse engineering, and so be able to easly swap between OpenWrt and the stock FW, it turned out that the stock FW does not light up the red and green USB LEDs exactly as I remembered. Signed-off-by: Daniele Castro <danielecastro@hotmail.it> [improve commit title] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: use dynamic partitioning for TP-Link CPE seriesMichael Pratt2021-06-051-14/+4
| | | | | | | | | | | | | | | | | | | | | | | | | CPExxx and WBSxxx boards with AR9344 SOC use the OKLI lzma kernel loader with the offset of 3 blocks of length 4k (0x3000) in order to have a fake "kernel" that cannot grow larger than how it is defined in the now static OEM partition table. Before recent changes to the mtdsplit driver, the uImage parser for OKLI only supported images that started exactly on an eraseblock boundary. The mtdsplit parser for uImage now supports identifying images with any magic number value and at any offset from the eraseblock boundary using DTS properties to define those values. So, it is no longer necessary to use fixed sizes for kernel and rootfs Tested-by: Andrew Cameron <apcameron@softhome.net> [CPE510 v2] Tested-by: Bernhard Geier <freifunk@geierb.de> [WBS210 v2] Tested-by: Petrov <d7c48mWsPKx67w2@gmail.com> [CPE210 v1] Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ipq806x: add support for Askey RT4230W REV6Lauro Moreno2021-06-057-11/+333
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Askey RT4230W REV6 (Branded by Spectrum/Charter as RAC2V1K) At this time, there's no way to reinstall the stock firmware so don't install this on a router that's being rented. Specifications: Qualcomm IPQ8065 1 GB of RAM (DDR3) 512 MB Flash (NAND) 2x Wave 2 WiFi cards (QCA9984) 5x 10/100/1000 Mbps Ethernet (Switch: QCA8337) 1x LED (Controlled by a microcontroller that switches it between red and blue with different patterns) 1x USB 3.0 Type-A 12V DC Power Input UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V Port settings are 115200n8 More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830 https://deviwiki.com/wiki/Askey_RAC2V1K To check what revision your router is, restore one of these config backups through the stock firmware to get ssh access then run "cat /proc/device-tree/model". https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17 The revision number on the board doesn't seem to be very consistent so that's why this is needed. You can also run printenv in the uboot console and if machid is set to 177d, that means your router is rev6. Note: Don't install this if the router is being rented from an ISP. The defined partition layout is different from the OEM one and even if you changed the layout to match, backing up and restoring the OEM firmware breaks /overlay so nothing will save and the router will likely enter a bootloop. How to install: Method 1: Install without opening the case using SSH and tftp You'll need: RAC2V1K-SSH.zip: https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip initramfs and sysupgrade images Connect to one of the router's LAN ports Download the RAC2V1K-SSH.zip file and restore the config file that corresponds to your router's firmware (If you're firmware is newer than what's in the zip file, just restore the 1.1.16 file) After a reboot, you should be able to ssh into the router with username: "4230w" and password: "linuxbox" or "admin". Run the following commannds fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as it's in the same subnet as the server fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next steps fw_setenv bootdelay 8 fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq" Don't reboot the router yet. Install and set up a tftp server on your computer Set a static ip on the ethernet interface of your computer (use this for serverip in the above commands) Rename the initramfs image to initramfs.bin, and host it with the tftp server Reboot the router. If you set up everything right, the router led should switch over to a slow blue glow which means openwrt is booted. If for some reason the file doesn't get loaded into ram properly, it should still boot to the OEM firmware. After openwrt boots, ssh into it and run these commands: fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" fw_setenv bootdelay 2 After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Method 2: Install with serial access (Do this if something fails and you can't boot after using method 1) You'll need: initramfs and sysupgrade images Serial access: https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case Install and set up a tftp server Set a static ip on the ethernet interface of your computer Download the initramfs image, rename it to initramfs.bin, and host it with the tftp server Connect the wan port of the router to your computer Interrupt U-Boot and run these commands: setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer) setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet) setenv bootcmd "setenv mtdids nand0=nand0 && set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" saveenv tftpboot initramfs.bin bootm After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Signed-off-by: Lauro Moreno <lmore377@gmail.com> [add entry in 5.10 patch, fix whitespace issues] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Linksys EA8100 v1Tee Hao Wei2021-06-057-4/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 256MB - Flash: 128MB NAND - Ethernet: 5 Gigabit ports - WiFi: 2.4G/5G MT7615N - USB: 1 USB 3.0, 1 USB 2.0 This device is very similar to the EA7300 v1/v2 and EA7500 v2. Installation: Upload the generated factory image through the factory web interface. (following part taken from EA7300 v2 commit message:) This might fail due to the A/B nature of this device. When flashing, OEM firmware writes over the non-booted partition. If booted from 'A', flashing over 'B' won't work. To get around this, you should flash the OEM image over itself. This will then boot the router from 'B' and allow you to flash OpenWRT without problems. Reverting to factory firmware: Hard-reset the router three times to force it to boot from 'B.' This is where the stock firmware resides. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. With thanks to Leon Poon (@LeonPoon) for the initial bringup. Signed-off-by: Tee Hao Wei <angelsl@in04.sg> [add missing entry in 10_fix_wifi_mac] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Amped Wireless ALLY router and extenderJonathan Sturges2021-06-056-15/+293
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Amped Wireless ALLY is a whole-home WiFi kit, with a router (model ALLY-R1900K) and an Extender (model ALLY-00X19K). Both are devices are 11ac and based on MediaTek MT7621AT and MT7615N chips. The units are nearly identical, except the Extender lacks a USB port and has a single Ethernet port. Specification: - SoC: MediaTek MT7621AT (2C/4T) @ 880MHz - RAM: 128MB DDR3 (Nanya NT5CC64M16GP-DI) - FLASH: 128MB NAND (Winbond W29N01GVSIAA) - WiFi: 2.4/5 GHz 4T4R - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac - Switch: SoC integrated Gigabit Switch - USB: 1x USB3 (Router only) - BTN: Reset, WPS - LED: single RGB - UART: through-hole on PCB. J1: pin1 (square pad, towards rear)=3.3V, pin2=RX, pin3=GND, pin4=TX. Settings: 57600/8N1. Note regarding dual system partitions ------------------------------------- The vendor firmware and boot loader use a dual partition scheme. The boot partition is decided by the bootImage U-boot environment variable: 0 for the 1st partition, 1 for the 2nd. OpenWrt does not support this scheme and will always use the first OS partition. It will set bootImage to 0 during installation, making sure the first partition is selected by the boot loader. Also, because we can't be sure which partition is active to begin with, a 2-step flash process is used. We first flash an initramfs image, then follow with a regular sysupgrade. Installation: Router (ALLY-R1900K) 1) Install the flashable initramfs image via the OEM web-interface. (Alternatively, you can use the TFTP recovery method below.) You can use WiFi or Ethernet. The direct URL is: http://192.168.3.1/07_06_00_firmware.html a. No login is needed, and you'll be in their setup wizard. b. You might get a warning about not being connected to the Internet. c. Towards the bottom of the page will be a section entitled "Or Manually Upgrade Firmware from a File:" where you can manually choose and upload a firmware file. d: Click "Choose File", select the OpenWRT "initramfs" image and click "Upload." 2) The Router will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 3) Log into LuCI as root; there is no password. 4) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 5) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Extender (ALLY-00X19K) 1) This device requires a TFTP recovery procedure to do an initial load of OpenWRT. Start by configuring a computer as a TFTP client: a. Install a TFTP client (server not necessary) b. Configure an Ethernet interface to 192.168.1.x/24; don't use .1 or .6 c. Connect the Ethernet to the sole Ethernet port on the X19K. 2) Put the ALLY Extender in TFTP recovery mode. a. Do this by pressing and holding the reset button on the bottom while connecting the power. b. As soon as the LED lights up green (roughly 2-3 seconds), release the button. 3) Start the TFTP transfer of the Initramfs image from your setup machine. For example, from Linux: tftp -v -m binary 192.168.1.6 69 -c put initramfs.bin 4) The Extender will flash the OpenWrt initramfs image and reboot. After booting, LuCI will be available on 192.168.1.1. 5) Log into LuCI as root; there is no password. 6) Optional (but recommended) is to backup the OEM firmware before continuing; see process below. 7) Complete the Installation by flashing a full OpenWRT image. Note: you may use the sysupgrade command line tool in lieu of the UI if you prefer. a. Choose System -> Backup/Flash Firmware. b. Click "Flash Image..." under "Flash new firmware image" c. Click "Browse..." and then select the sysupgrade file. d. Click Upload to upload the sysupgrade file. e. Important: uncheck "Keep settings and retain the current configuration" for this initial installation. f. Click "Continue" to flash the firmware. g. The device will reboot and OpenWRT is installed. Backup the OEM Firmware: ----------------------- There isn't any downloadable firmware for the ALLY devices on the Amped Wireless web site. Reverting back to the OEM firmware is not possible unless we have a backup of the original OEM firmware. The OEM firmware may be stored on either /dev/mtd3 ("firmware") or /dev/mtd6 ("oem"). We can't be sure which was overwritten with the initramfs image, so backup both partitions to be safe. 1) Once logged into LuCI, navigate to System -> Backup/Flash Firmware. 2) Under "Save mtdblock contents," first select "firmware" and click "Save mtdblock" to download the image. 3) Repeat the process, but select "oem" from the pull-down menu. Revert to the OEM Firmware: -------------------------- * U-boot TFTP: Follow the TFTP recovery steps for the Extender, and use the backup image. * OpenWrt "Flash Firmware" interface: Upload the backup image and select "Force update" before continuing. Signed-off-by: Jonathan Sturges <jsturges@redhat.com>
* ramips: add support for Linksys E5600Aashish Kulkarni2021-06-057-0/+212
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This submission relied heavily on the work of Linksys EA7300 v1/ v2. Specifications: * SoC: MediaTek MT7621A (880 MHz 2c/4t) * RAM: 128M DDR3-1600 * Flash: 128M NAND * Eth: MediaTek MT7621A (10/100/1000 Mbps x5) * Radio: MT7603E/MT7613BE (2.4 GHz & 5 GHz) * Antennae: 2 internal fixed in the casing and 2 on the PCB * LEDs: Blue (x4 Ethernet) Blue+Orange (x2 Power + WPS and Internet) * Buttons: Reset (x1) WPS (x1) Installation: Flash factory image through GUI. This device has 2 partitions for the firmware called firmware and alt_firmware. To successfully flash and boot the device, the device should have been running from alt_firmware partition. To get the device booted through alt_firmware partition, download the OEM firmware from Linksys website and upgrade the firmware from web GUI. Once this is done, flash the OpenWrt Factory firmware from web GUI. Reverting to factory firmware: 1. Boot to 'alt_firmware'(where stock firmware resides) by doing one of the following: Press the "wps" button as soon as power LED turns on when booting. (OR) Hard-reset the router consecutively three times to force it to boot from 'alt_firmware'. 2. To remove any traces of OpenWRT from your router simply flash the OEM image at this point. Signed-off-by: Aashish Kulkarni <aashishkul@gmail.com> [fix hanging indents and wrap to 74 characters per line, add kmod-mt7663-firmware-sta package for 5GHz STA mode to work, remove sysupgrade.bin and concatenate IMAGES instead in mt7621.mk, set default-state "on" for power LED] Signed-off-by: Sannihith Kinnera <digislayer@protonmail.com> [move check-size before append-metadata, remove trailing whitespace] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add netgear wac510 supportRobert Marko2021-06-057-1/+411
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear WAC510 Insight Managed Smart Cloud Wireless Access Point, an indoor dual-band, dual-radio 802.11ac business-class wireless AP with integrated omnidirectional antennae and two 10/100/1000 Mbps Ethernet ports. For more information see: <https://www.netgear.com/business/wifi/access-points/wac510> Specifications: SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB Flash1: 2 MiB Winbond W25Q16JV SPI-NOR Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port, WAN port active IEEE 802.3af/at PoE in Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1 LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN Serial: Header J2 1 - 3.3 Volt (Do NOT connect!) 2 - TX 3 - RX 4 - Ground WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter! The Serial settings are 115200-8-N-1. Installation via Stock Web Interface: BTW: The default factory console/web interface login user/password are admin/password. In the web interface navigating to Management - Maintenance - Upgrade - 'Firmware Upgrade' will show you what is currently installed e.g.: Manage Firmware Current Firmware Version: V5.0.10.2 Backup Firmware Version: V1.2.5.11 Under 'Upgrade Options' choose Local (alternatively SFTP would be available) then click/select 'Browse File' on the right side, choose openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar and hit the Upgrade button below. After a minute or two your browser should indicate completion printing 'Firmware update complete.' and 'Rebooting AP...'. Note that OpenWrt will use the WAN PoE port as actual WAN port defaulting to DHCP client but NOT allowing LuCI access, use LAN port defaulting to 192.168.1.1/24 to access LuCI. Installation via TFTP Requiring Serial U-Boot Access: Connect to the device's serial port and hit any key to stop autoboot. Upload and boot the initramfs based OpenWrt image as follows: (IPQ40xx) # setenv serverip 192.168.1.1 (IPQ40xx) # setenv ipaddr 192.168.1.2 (IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb (IPQ40xx) # bootm Note: This only runs OpenWrt from RAM and has not installed anything to flash as of yet. One may permanently install OpenWrt as follows: Check the MTD device number of the active partition: root@OpenWrt:/# dmesg | grep 'set to be root filesystem' [ 1.010084] mtd: device 9 (rootfs) set to be root filesystem Upload the factory image ending with .ubi to /tmp (e.g. using scp or tftp). Then flash the image as follows (substituting the 9 in mtd9 below with whatever number reported above): root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi And reboot. Dual Image Configuration: The default U-Boot boot command bootipq uses the U-Boot environment variables primary/secondary to decide which image to boot. E.g. primary=0, secondary=3800000 uses rootfs while primary=3800000, secondary=0 uses rootfs_1. Switching their values changes the active partition. E.g. from within U-Boot: (IPQ40xx) # setenv primary 0 (IPQ40xx) # setenv secondary 3800000 (IPQ40xx) # saveenv Or from a OpenWrt userspace serial/SSH console: fw_setenv primary 0 fw_setenv secondary 3800000 Note that if you install two copies of OpenWrt then each will have its independent configuration not like when switching partitions on the stock firmware. BTW: The kernel log shows which boot partition is active: [ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB) vs. [ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB) Note: After 3 failed boot attempts it automatically switches partition. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [squashed netgear-tar commit into main and rename netgear-tar for now, until it is made generic.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: enable additional UART on MikroTik RouterBOARD M33GPhilipp Borgers2021-06-051-0/+4
| | | | | | | The RouterBOARD M33G has an additional UART that should be enabled by default. Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
* ath79: add support for Qualcomm AP143 reference boardsZoltan HERPAI2021-06-057-1/+275
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SoC: QCA9533 DRAM: 32Mb DDR1 Flash: 8/16Mb SPI-NOR LAN: 4x 10/100Mbps via AR8229 switch (integrated into SoC) on GMII WAN: 1x 10/100Mbps via MII WLAN: QCA9530 USB: 1x 2.0 UART: standard QCA UART header JTAG: yes Button: 1x WPS, 1x reset LEDs: 8x LEDs A version with 4Mb flash is also available, but due to lack of enough space it's not supported. As the original flash layout does not provide enough space for the kernel (1472k), the firmware uses OKLI and concat flash to overcome the limitation without changing the boot address of the bootloaders. Installation: 1. Original bootloader Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin available via TFTP tftpboot 0x80060000 openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize Reboot the board. 2. pepe2k's u-boot_mod Connect the board to ethernet Set up a server with an IP address of 192.168.1.10 Make the openwrt-ath79-generic-qca_ap143-8m-squashfs-factory.bin available via TFTP, as "firmware.bin" run fw_upg Reboot the board. For the 16M version of the board, please use openwrt-ath79-generic-qca_ap143-16m-squashfs-factory.bin Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu> [use fwconcatX names, drop redundant uart status, fix IMAGE_SIZE, set up IMAGE/factory.bin without metadata] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Add support for OpenMesh A40Sven Eckelmann2021-06-055-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2T2R 2.4 GHz Wi-Fi (11n) * 2T2R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8035 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ath79: Add support for OpenMesh A60Sven Eckelmann2021-06-056-0/+201
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: ====================== * Qualcomm/Atheros QCA9558 ver 1 rev 0 * 720/600/240 MHz (CPU/DDR/AHB) * 128 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 3T3R 2.4 GHz Wi-Fi (11n) * 3T3R 5 GHz Wi-Fi (11ac) * multi-color LED (controlled via red/green/blue GPIOs) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default)) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x ethernet - eth0 + Label: Ethernet 1 + AR8035 ethernet PHY (RGMII) + 10/100/1000 Mbps Ethernet + 802.3af POE + used as WAN interface - eth1 + Label: Ethernet 2 + AR8031 ethernet PHY (SGMII) + 10/100/1000 Mbps Ethernet + used as LAN interface * 1x USB * internal antennas Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin Signed-off-by: Sven Eckelmann <sven@narfation.org>
* kernel: ar8216: remove soft_resetDavid Bauer2021-06-031-8/+0
| | | | | | | | | | ar8xxx_soft_reset is effectively a NOP function. In the PHY state machine, the availability and result of a soft_reset function makes no difference for the code flow. Thus, we can safely remove this method. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: ar8216: add get_features methodDavid Bauer2021-06-031-23/+20
| | | | | | | | | | | | | | Modifying PHY capabilities in the probe function broke with upstream commit 92ed2eb7f4b7 ("net: phy: probe the PHY before determining the supported features"). AR8316 switches only support 10/100 Mbit/s link modes because of this change. Provide a get_features method for the PHY driver, so Gigabit link mode will be advertised to link partners again. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: backport fix for hang on napi_disable with threaded NAPIFelix Fietkau2021-06-012-4/+57
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* layerscape: refresh kernel configAdrian Schmutzler2021-05-302-202/+3
| | | | | | | | Run `make kernel_oldconfig CONFIG_TARGET=subtarget` This mostly aims at getting rid of redundant/unneeded symbols. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: add missing symbol CONFIG_AHCI_XGENEYangbo Lu2021-05-303-1/+2
| | | | | | | | Add missing symbol CONFIG_AHCI_XGENE. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [also add for 5.10, remove from layerscape target config] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.123John Audia2021-05-291-1/+1
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* ramips: add support for Wavlink WL-WN578A2Thomas Aldrian2021-05-284-3/+182
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug wireless router. This device is also sold under the name SilverCrest SWV 733 A2. Device Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 2x 10/100 Mbps - 2.4 GHz: 802.11b/g/n SoC - 5 GHz: 802.11a/n/ac MT7610E - Antennas: internal - 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high - Buttons: Reset, WPS - Sliding mode switch: AP, repeater, client - Small sliding power switch Flashing instructions: U-Boot launches TFTP client if WPS button is pressed during power-on. Configure as follows: - Server IP: 192.168.10.100 - Filename (rename sysupgrade file to this): firmware.bin Flashing should not take more than a minute, device will reboot automatically. Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
* kernel: bump 5.10 to 5.10.40Rui Salvaterra2021-05-272-2/+2
| | | | | | | | Automatically refreshed: generic/hack-5.10/902-debloat_proc.patch generic/pending-5.10/110-perf-jevents-fix-getting-maximum-number-of-fds.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* base-files: generate network config with "device" optionsRafał Miłecki2021-05-272-4/+4
| | | | | | | Replace "ifname" with "device" as netifd has been recently patches to used the later one. It's more clear and accurate. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: add missing v5.4 SPI chipselect patchDavid Bauer2021-05-261-0/+26
| | | | | | | | | The patch was not applied to the v5.4 target, thus breaking Kernel 5.4 on devices with multiple flash chips attache to the SPI bus. Fixes commit bd54e739541b ("ath79: set number of chipselect lines") Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for JCG Q20Chukun Pan2021-05-265-0/+198
| | | | | | | | | | | | | | | | | | | | | | | | | JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: add support for cudy WR2100Leon M. George2021-05-263-0/+218
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications SoC: MT7621 CPU: 880 MHz Flash: 16 MiB RAM: 128 MiB WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac MT7603E / MT7615E Ethernet: 5x Gbit ports Installation There are two known options: 1) The Luci-based UI. 2) Press and hold the reset button during power up. The router will request 'recovery.bin' from a TFTP server at 192.168.1.88. Both options require a signed firmware binary. The openwrt image supplied by cudy is signed and can be used to install unsigned images. R4 & R5 need to be shorted (0-100Ω) for the UART to work. Signed-off-by: Leon M. George <leon@georgemail.eu> [remove non-required switch-port node - remove trgmii phy-mode] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for TP-Link Archer C6U v1 (EU)Georgi Vlaev2021-05-263-1/+229
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for TP-Link Archer C6U v1 (EU). The device is also known in some market as Archer C6 v3. This patch supports only Archer C6U v1 (EU). Specifications: -------------- * SoC: Mediatek MT7621AT 2C2T, 880MHz * RAM: 128MB DDR3 * Flash: 16MB SPI NOR flash (Winbond 25Q128) * WiFi 5GHz: Mediatek MT7613BEN (2x2:2) * WiFi 2.4GHz: Mediatek MT7603EN (2x2:2) * Ethernet: MT7630, 5x 1000Base-T. * LED: Power, WAN, LAN, WiFi 2GHz and 5GHz, USB * Buttons: Reset, WPS. * UART: Serial console (115200 8n1), J1(GND:3) * USB: One USB2 port. Installation: ------------ Install the OpenWrt factory image for C6U is from the TP-Link web interface. 1) Go to "Advanced/System Tools/Firmware Update". 2) Click "Browse" and upload the OpenWrt factory image: openwrt-ramips-mt7621-tplink_archer-c6u-v1-squashfs-factory.bin. 3) Click the "Upgrade" button, and select "Yes" when prompted. Recovery to stock firmware: -------------------------- The C6U bootloader has a failsafe mode that provides a web interface (running at 192.168.0.1) for reverting back to the stock TP-Link firmware. The failsafe interface is triggered from the serial console or on failed kernel boot. Unfortunately, there's no key combination that enables the failsafe mode. This gives us two options for recovery: 1) Recover using the serial console (J1 header). The recovery interface can be selected by hitting 'x' when prompted on boot. 2) Trigger the bootloader failsafe mode. A more dangerous option is force the bootloader into recovery mode by erasing the OpenWrt partition from the OpenWrt's shell - e.g "mtd erase firmware". Please be careful, since erasing the wrong partition can brick your device. MAC addresses: ------------- OEM firmware configuration: D8:07:B6:xx:xx:83 : 5G D8:07:B6:xx:xx:84 : LAN (label) D8:07:B6:xx:xx:84 : 2.4G D8:07:B6:xx:xx:85 : WAN Signed-off-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
* ramips: add support for TP-Link Archer A6 v3Vinay Patil2021-05-263-0/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds support for the TP-Link Archer A6 v3 The router is sold in US and India with FCC ID TE7A6V3 Specification ------------- MediaTek MT7621 SOC RAM: 128MB DDR3 SPI Flash: W25Q128 (16MB) Ethernet: MT7530 5x 1000Base-T WiFi 5GHz: Mediatek MT7613BE WiFi 2.4GHz: Mediatek MT7603E UART/Serial: 115200 8n1 Device Configuration & Serial Port Pins --------------------------------------- ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN _______________________ | | Serial Pins: | VCC GND TXD RXD | |_____________________| LEDs: Power Wifi2G Wifi5G LAN WAN Build Output ------------ The build will generate following set of files [1] openwrt-ramips-mt7621-tplink_archer-a6-v3-initramfs-kernel.bin [2] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-factory.bin [3] openwrt-ramips-mt7621-tplink_archer-a6-v3-squashfs-sysupgrade.bin How to Use - Flashing from TP-Link Web Interface ------------------------------------------------ * Go to "Advanced/System Tools/Firmware Update". * Click "Browse" and upload the OpenWrt factory image: factory.bin[2] * Click the "Upgrade" button, and select "Yes" when prompted. TFTP Booting ------------ Setup a TFTP boot server with address 192.168.0.5. While starting U-boot press '4' key to stop autoboot. Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin From u-boot command prompt run tftpboot followed by bootm. Recovery -------- Archer A6 V3 has recovery page activated if SPI booting from flash fails. Recovery page can be activated from serial console only. Press 'x' while u-boot is starting Note: TFTP boot can be activated only from u-boot serial console. Device recovery address: 192.168.0.1 Thanks to: Frankis for Randmon MAC address fix. Signed-off-by: Vinay Patil <post2vinay@gmail.com> [remove superfluous factory image definition, whitespacing] Signed-off-by: David Bauer <mail@david-bauer.net>
* imx6: image: drop BOOT_SCRIPT and fix DEVICE_NAMEPiotr Dymacz2021-05-262-14/+3
| | | | | | | | | | | | | | This fixes Gateworks Ventana 'DEVICE_NAME' variable which value wasn't adjusted during migration to common 'vendor_model' image naming scheme (fixes: FS#3825). Furthermore, drop unused 'Build/boot-scr' recipe, get rid of redundant 'BOOT_SCRIPT' variable (use already provided 'DEVICE_NAME' instead) and drop custom 'DEVICE_NAME' variable from SolidRun CuBox-i image recipe (use default one instead). Fixes: cbc8bcfbaa ("imx6: image: use vendor_model scheme") Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: fix a perf build errorFelix Fietkau2021-05-251-0/+24
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: update mtd parser patchesHauke Mehrtens2021-05-236-85/+94
| | | | | | | This updates the patches to match the versions included in the mtd subsystem for the next Linux kernel version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: backport "mvmdio avoid error message for optional IRQ"Daniel González Cabanelas2021-05-231-0/+33
| | | | | | | | | Rid of kernel error message: [ 0.780828] orion-mdio d0072004.mdio: IRQ index 0 not found on Marvell targets backporting the kernel commit fa2632f74e57 Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
* generic: mt7530: fix EEE patchDENG Qingfang2021-05-231-1/+1
| | | | | | | The higher 16-bit of EEE register was overwritten by mistake, fix that. Fixes: 5b9ba4a93e83 ("generic: mt7530: support adjusting EEE") Signed-off-by: DENG Qingfang <dqfext@gmail.com>
* mvebu: 5.10 fix DVFS caused random boot crashesRobert Marko2021-05-232-0/+214
| | | | | | | | | | | | | | | | | 5.10.37 and 5.4.119 introduced a lot of DVFS changes for Armada 37xx from 5.13 kernel. Unfortunately commit: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/cpufreq/armada-37xx-cpufreq.c?h=v5.10.37&id=a13b110e7c9e0dc2edcc7a19d4255fc88abd83cc This patch actually corrects the things so that 1 or 1.2GHz models would actually get scaled to their native frequency. However, due to a AVS setting voltages too low this will cause random crashes on 1.2GHz models. So, until a new safe for everybody voltage is agreed on lets revert the patch. Fixes: d337731 ("kernel: bump 5.10 to 5.10.37") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* apm821xx: MR24: Change default config of WLAN LEDTan Zien2021-05-231-4/+4
| | | | | | | | | | | | The previous config will only show 2.4G radio activity status This change mr24:green:wifi4 and mr24:green:wifi2 to show 2.4G and 5G radio on and off status change mr24:green:wifi3 and mr24:green:wifi1 to show 2.4G and 5G radio activity status Signed-off-by: Tan Zien <nabsdh9@gmail.com>
* ipq806x: fix warning about tsens debugfs already registeredAnsuel Smith2021-05-232-0/+95
| | | | | | Backport a pending patch already reviewed that fix some warning about tsens debugs already registered. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-02 23:36:16 +0000