aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.9 to 4.9.58Stijn Tintel2017-10-238-215/+193
| | | | | | | | Refresh patches. Compile-tested: ar71xx, octeon, x86/64. Runtime-tested: octeon, x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* brcm2708: restore /boot/config.txt before rebootStijn Tintel2017-10-232-0/+2
| | | | | | | | | | | | | | The Raspberry Pi bootloader reads configuration values from config.txt in the boot partition. This file allows to specify the amount of memory to assign to the GPU, the license keys for hardware MPEG-2 and VC-1 decoding, Device Tree parameters and overlays, and lots of other things. Since sysupgrade only restores the configuration after booting the newly flashed image, these values will not be active, even if sysupgrade would save /boot/config.txt. To solve this, add the file to the files to be backed up, and restore it in platform_copy_config, before reboot. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ar71xx: deactivate some boards with too small kernel partitionsHauke Mehrtens2017-10-223-5/+2
| | | | | | | | | | | | | | | | | | | This affects the following boards: * dr344 * archer-c58-v1 * archer-c60-v1 * tl-wr902ac-v1 * tl-wr942n-v1 * ubnt-uap-pro * ubnt-unifi-outdoor-plus The build fails for any of these boards because the resulting kernel image will not fit into the kernel partition. When CONFIG_KERNEL_KALLSYMS is not set it could be that the kernel will fit onto the board again, this is the case for release images. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: use kernel 4.9 by defaultHauke Mehrtens2017-10-221-1/+1
| | | | | | | | | Kernel 4.9 support was added about 2 weeks ago and we haven't seen any major regression so far. This patch was not ported to kernel 4.9, this needs some additional work: 821-serial-core-add-support-for-boot-console-with-arbitr.patch Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* at91: remove unused at91part driverHauke Mehrtens2017-10-221-122/+0
| | | | | | | There is no patch in the kernel 4.4 and 4.9 patches which adds this driver to the build system. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* at91: update to kernel 4.9Hauke Mehrtens2017-10-229-23/+26
| | | | | | | This brings the at91 target to kernel 4.9. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Tested-by: Ben Whitten <ben.whitten@gmail.com>
* kernel: add config optionHauke Mehrtens2017-10-221-0/+1
| | | | | | | | When the kmod-at91-adc package is activated for the at91 target the new option CONFIG_AT91_SAMA5D2_ADC is selectable and not handled. Add this option to the kernel 4.9 configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: add support for TP-LINK Archer C7 v4Felix Fietkau2017-10-1911-2/+292
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C7 v4 is a dual-band AC1750 router, based on Qualcomm/Atheros QCA9561+QCA9888. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction: 1. Upload lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c7-v4-squashfs-factory.bin and rename it to ArcherC7v4_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Flash instruction under U-Boot, using UART: 1. tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin 2. erase 0x9f040000 +$filesize 3. cp.b $fileaddr 0x9f040000 $filesize 4. reset Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ar71xx: add support for Nokia WI2A-AC200iFelix Fietkau2017-10-1914-0/+286
| | | | | | | | | | | | | | | | | Specifications: - SoC: Qualcomm QCA9558 (720 MHz) - RAM: 256MB - Storage: 1MB NOR, 128 MB NAND flash - Ethernet: 1x1000M Installation: 1. Connect to serial console on the board 2. Boot initramfs image over u-boot 3. Copy image to the device and run sysupgrade Installation without serial console is not supported at this time Signed-off-by: Felix Fietkau <nbd@nbd.name>
* brcm47xx: use kernel 4.9 by defaultHauke Mehrtens2017-10-181-1/+1
| | | | | | | | Kernel 4.9 is now working on the brcm47xx boards, we just recently fixed the problem that some boards did not boot at all, by changing the memory regions used to relocate the kernel to in the loader. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: fix ftrace support on 4.9Felix Fietkau2017-10-181-0/+27
| | | | | | | | When porting the kernel patches from 4.4 to 4.9, they were missing a small chunk that ensures that ftrace sections are kept in the vmlinux image, even when linked with --gc-sections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: ARV752DPW22: fix wireless mac addressMathias Kresin2017-10-181-0/+1
| | | | | | | | | | The ARV752DPW22 has the same generic mac address in the EEPROM as it was already noticed for other lantiq boards using a ralink wireless. Use the base mac address from the boardconfig partition as it is done by the stock firmware. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ARV752DPW22: set correct wireless led triggerMathias Kresin2017-10-181-0/+3
| | | | | | | The ARV752DPW22 has a ralink based wireless and can not use the ath9k only phy0tpt trigger. Signed-off-by: Mathias Kresin <dev@kresin.me>
* omap: clean up configurationHauke Mehrtens2017-10-182-17/+1
| | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Alexander Couzens <lynxis@fe80.eu>
* omap: Add support for kernel 4.9Hauke Mehrtens2017-10-184-1/+759
| | | | | | | | | | | | | | | | This adds support for kernel 4.9 and replaces the kernel 4.4 support. These are lynxis test results: panda-board a3 - works, but no network, but master/4.4 doesn't have network either. panda-board-a4 - u-boot SPL refuse to boot. beaglebone-black - works beagle-board - usb attached network doesn't come up and I doesn't have a serial around. beagle-board-xm - ToDo: image code is missing. Kernel 4.4 does not look better, so we merge this anyway. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Alexander Couzens <lynxis@fe80.eu>
* kernel: bump 4.9 to 4.9.57Kevin Darbyshire-Bryant2017-10-1821-234/+250
| | | | | | | | | | | | | | | | Refresh patches. Compile-tested for ar71xx - Archer C7 v2 Runtime-tested on ar71xx - Archer C7 v2 Fixes the following CVEs: - CVE-2017-7518 - CVE-2017-0786 - CVE-2017-1000255 - CVE-2017-12188 - CVE-2017-15265 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* Revert "ar71xx: Add GRO support to ag71xx"Felix Fietkau2017-10-171-3/+3
| | | | | | | | | | This reverts commit 13e5e473699b92f171205e0f5c57c9ebe7922492. This commit causes a severe regression in LAN->WAN routing performance for several devices. This appears to be caused by the extra requirement to validate the SKB checksum early in the rx path, which the ethernet hardware does not do Signed-off-by: Felix Fietkau <nbd@nbd.name>
* at91: fix legacy buildHauke Mehrtens2017-10-161-2/+1
| | | | | | | | | | | The build system took the DTB_SIZE definition from Default and not from production-dtb under some conditions. Move the size definitions to Default now as it is only used in production-dtb anyway. Thanks Mathias Kresin for helping me with this. Fixes: c2f052acaeb ("at91: convert boards to generic build target") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: fix typo in MT7621 NAND driverFelix Fietkau2017-10-161-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* malta: activate some more standard kernel featuresHauke Mehrtens2017-10-151-5/+0
| | | | | | | | These options where deactivated in the malta kernel, take the default options form the generic kernel configuration now to better match the other targets. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* malta: upgrade to kernel 4.9Hauke Mehrtens2017-10-156-44/+32
| | | | | | This brings the MIPS malta target to kernel 4.9. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* malta: add 64 bit qemu commands to READMEHauke Mehrtens2017-10-151-2/+8
| | | | | | This shows how to boot up the 64 bit images. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: xrx200: rename nas0/ptm0 to dsl0Martin Schiller2017-10-153-2/+59
| | | | | | | | | | | | | This change makes it possible to configure the wan/dsl ppp interface settings independantly from the used TC-Layer (ATM/PTM). Now you can move a device from an ADSL/ATM port to an VDSL/PTM port without any configuration changes for example. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [use the dsl0 interface name for the default netdev trigger in 01_led, add ip dependency] Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: clean up ClearFog Base package selectionRyan Mounce2017-10-151-6/+2
| | | | | | | | | | It is unclear why so many packages are selected for ClearFog Base compared to its big brother, and there is no reason to not append metadata for Base. Tidy this up as the only hardware difference between Base/Pro is the presence of a switch and a different board name / device tree. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* mvebu: Fix ClearFog sysupgrade board definitionsRyan Mounce2017-10-151-5/+2
| | | | | | | Remove redundancy for platform_do_upgrade_clearfog Fix platform_copy_config_clearfog to reflect -base/-pro split Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* mvebu: Sort 02_network alphabeticallyRyan Mounce2017-10-151-6/+6
| | | | Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* at91: add support for the WB50N module from LairdBen Whitten2017-10-154-0/+348
| | | | | | | | | | | | | | This module from Laird includes the following: - CPU Atmel SoC SAMA5D31 - Wifi QCA6004 - Bluetooth CSR8811 - RAM 64MB LPDDR - FLASH 128MB The flash is a dual image layout, kernel a/b, rootfs a/b, and a user partition. Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
* at91: add support for the WB45N module from LairdBen Whitten2017-10-154-0/+253
| | | | | | | | | | | | | | This module from Laird includes the following: - CPU Atmel SoC ARM926EJS - Wifi AR6003 - Bluetooth CSR8510 - RAM 64MB LPDDR - FLASH 128MB The flash is a dual image layout, kernel a/b, rootfs a/b, and a user partition. Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
* at91: separate MKUBIFS opts to defaults in the sub targetBen Whitten2017-10-153-13/+18
| | | | | | | Instead of applying global defaults based on selected board, transition to using a per board setting for UBIFS and UBINIZE. Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
* at91: refresh kernel config, enable UBI block and DMABen Whitten2017-10-151-1/+6
| | | | | | | | | The platform generates squashfs images in a UBI block but misses the kernel module to be able to mount the block. DMA is also enabled to allow systems which include them in the DTS to use it. Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
* sunxi: backport support for Allwinner Security System PRNGLucian Cristian2017-10-153-0/+208
| | | | Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
* ar71xx: add support for Mikrotik RB750P-PBr2Robert Marko2017-10-149-2/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: Qualcomm QCA9531 (650MHz) - RAM: 64MB - Storage: 16MB NOR SPI flash - Ethernet: 5x100M (1 PoE in, 4 PoE out) - Outdoor use ready This ethernet router is based on the same platform as the hEX PoE lite. Installation 1. login to the Mikrotik WebUI to backup your licence keys 2. setup a DHCP/BOOTP Server with: * DHCP-Option 66 (TFTP server name) pointing to a local TFTP Server within the same subnet of the DHCP range * DHCP-Option 67 (Bootfile-Name) matching the initramfs filename of the to be booted image 3. connect the port labled internet to your local network 4. keep the reset button pushed down and power on the board The board should load and start the initramfs image from the TFTP Server. Login as root/without password to the started LEDE via ssh listing on IPv4 address 192.168.1.1. Use sysupgrade to install LEDE. Revert to RouterOS Use the "rbcfg" package on in LEDE: * rbcfg set boot_protocol bootp * rbcfg set boot_device ethnand * rbcfg apply Open Netinstall and reboot routerboard. Now netinstall sees routerboard and you can install RouterOS. If NetInstall gets stuck on Sending offer just wait for it to timeout and then close and open Netinstall again. Click on install again. In order for RouterOS to function properly, you need to restore license for the device. You can do that by including license in NetInstall Signed-off-by: Robert Marko <robimarko@gmail.com>
* ramips: add support for Kimax U25AWF-H1Daniel Kucera2017-10-147-0/+125
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Kimax U-25AWF-H1 is is a 2,5" HDD Enclosure with Wi-Fi/Eth conection and battery, based on MediaTek MT7620A. Patch rewritten from: https://forum.openwrt.org/viewtopic.php?pid=305643 Specification: - MT7620A CPU - 64 MB of RAM - 16 MB of FLASH - 802.11bgn WiFi - 1x 10/100 Mbps Ethernet - USB 2.0 Host - UART for serial console Flash instruction: 1. Download lede-ramips-mt7620-u25awf-h1-squashfs-sysupgrade.bin 2. Open webinterface a upgrade 3. After boot connect via ethernet to ip 192.168.1.1 Signed-off-by: Daniel Kucera <daniel.kucera@gmail.com> [fix reset button gpio, don't add a lan/wan vlan config for single port board, add -H1 suffix do make sure that this revision of the board is supported/tested] Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: Add Aerohive HiveAP-330 Access PointChris Blake2017-10-1411-10/+458
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following adds the Aerohive HiveAP-330 Access Point to LEDE under the mpc85xx/p1020 subtarget. Hardware: - SoC: Freescale P1020NSE2DFB - NAND: Intel JS28F512M29EWH 64MB - Memory: 2x ProMOS V59C1G01168QBJ3 128MB (Total of 256MB) - 2.4GHz WiFi: Atheros AR9390-AL1A - 5.0GHz WiFi: Atheros AR9390-AL1A - Eth1: Atheros AR8035-A PoE - Eth2: Atheros AR8035-A - TPM: Atmel AT97SC3204 - LED Driver: TI LP5521 Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, tftp boot the initramfs image: dhcp; tftpboot 0x1000000 192.168.1.101:lede- mpc85xx-p1020-hiveap-330-initramfs.zImage; tftpboot 0x6000000 192.168.1.101:lede-mpc85xx-p1020-hiveap-330.fdt; bootm 0x1000000 - 0x6000000; 3. Once booted, scp over the sysupgrade file and sysupgrade the device to flash LEDE to the NAND. sysupgrade /tmp/lede-mpc85xx-p1020-hiveap-330-sysupgrade.img Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* mpc85xx: Add cmdline override patchChris Blake2017-10-142-0/+38
| | | | | | | | | | This patch adds a new kernel option called CONFIG_CMDLINE_OVERRIDE. This setting is for devices with locked down u-boot environments, where users are unable to change the default bootargs. When set, the fdt driver will propagate the cmdline for the kernel from chosen/bootargs-override instead of chosen/bootargs as long as it exists within the DTB. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* mpc85xx: Enable initramfs for p1020 subtargetChris Blake2017-10-141-1/+1
| | | | | | | The following patch enables building of initramfs images by default for the P1020 subtarget in mpc85xx. Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* at91: Add ext4 filesystemSandeep Sheriker Mallikarjun2017-10-141-1/+1
| | | | | | | Add ext4 filesystem for creating sdcard image with ext4 rootfs and removing ext2 as it superset of ext4. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
* at91: Enable SDHCI for sama5 in default configSandeep Sheriker Mallikarjun2017-10-141-0/+4
| | | | | | | Enabled SDHCI for sama5 in kernel default config and this is needed to mount sdcard rootfs partition during boot. Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
* at91: refresh kernel configurationHauke Mehrtens2017-10-143-48/+35
| | | | | | | This was done by running "make kernel_oldconfig" and "make kernel_oldconfig CONFIG_TARGET=subtarget" Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: add fix for bgmac with B50212E B1 PHYRafał Miłecki2017-10-138-6/+204
| | | | | | | This PHY requires some extra programming to work reliably with all devices. Backport upstream fix for it. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* layerscape: only support 64-bit for ls1088ardb/ls2088ardbYangbo Lu2017-10-121-0/+2
| | | | | | | | This is no requirement and plan to support 32-bit for ls1088ardb and ls2088ardb. Current 32-bit firmware for them couldn't work, so only keep 64-bit support for these two boards in menuconfig. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* layerscape: fix compile issue for usb ehci-fsl driverYangbo Lu2017-10-121-0/+28
| | | | | | | | | | When build firmware for layerscape target with CONFIG_ALL_NONSHARED=y, there would be a compile issue of usb ehci-fsl driver. Actually this driver was for PPC platforms initially and was not ready for non-PPC now, but a kernel kconfig patch removed PPC dependency for it. So that kernel patch should be reverted. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
* ar71xx: fix section mismatchesHauke Mehrtens2017-10-1110-13/+13
| | | | | | Fix some section mismatches found with kernel 4.9. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ar71xx: Add kernel 4.9 supportHauke Mehrtens2017-10-11106-73/+8329
| | | | | | | | | | | | | This add support for kernel 4.9 to the ar71xx target. It was compile tested with the generic, NAND and mikrotik subtarget. Multiple members of the community tested it on their boards and did not report any major problem so far. Especially the NAND part received some changes to adapt to the new kernel APIs. The serial driver hack used for the Arduino Yun was not ported because the kernel changed there a lot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: relocate the stack in loaderHauke Mehrtens2017-10-112-2/+4
| | | | | | | | | | | By default we are reusing the stack provided by CFE, like it is intended by CFE. On my WRT54GS it is located at 0x8043BF30, so a big kernel image could overwrite it. Relocate it to a different memory region which is still under the 8MB RAM, but in the higher area. We only need this memory region for the stack of the loader, Linux will set up this for its own. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm47xx: relocate loader to higher addressHauke Mehrtens2017-10-111-1/+1
| | | | | | | | | | | | | | | | | | | | | The boot process on a WRT54GL works the following way: 1. CFE gets loaded by the boot rom from flash 2. CFE loads the loader from the flash and gzip uncompresses it 3. CFE starts the loader 4. The loader stores the FW arguments and relocates itself to BZ_TEXT_START (now 0x80600000) 5. The loader reads the Linux image from flash 6. The loader lzma decompresses the Linux image to LOADADDR (0x80001000) 7. The loader executes the uncompress Linux image at LOADADDR The BZ_TEXT_START was set to 0x80400000 before. When the kernel gets uncompressed and is bigger than BZ_TEXT_START - LOADADDR it overwrote the loader which was currently uncompressing it and made the board crash. Increase the BZ_TEXT_START my 2 MB to have more space for the kernel. Even on 16MB RAM devices the memory goes till 0x80FFFFFF so this should not be a problem. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm53xx: backport DTS changes up to the first 4.15 queued commitsRafał Miłecki2017-10-1016-0/+1324
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips/mt76x8: add initramfs support for tplink 841n v13Alexander Couzens2017-10-091-0/+1
| | | | | | | | | | | | | The tplink 841n v13 requires an tplink v2 image header in front of an initramfs image. To boot an initramfs image: - break the uboot by holding the '4' key - setup your tftp server 192.168.0.255 - tftp 81000000 lede-ramips-mt76x8-tl-wr841n-v13-initramfs-kernel.bin - bootm Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* mediatek: fix a sleep while atomic bug inside the ethernet driverJohn Crispin2017-10-091-0/+40
| | | | | | this sometimes happens when we have hw nat enabled. Signed-off-by: John Crispin <john@phrozen.org>
* kernel: bump 4.9 to 4.9.54Stijn Tintel2017-10-089-112/+12
| | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: - ramips/0067-enable-mt7621-xhci.patch - ramips/0085-pinmux-util.patch - ramips/301-fix-rt3883.patch Compile-tested on brcm2708/bcm2708, octeon, ramips/mt7621, x86/64. Runtime-tested on brcm2708/bcm2708, octeon, ramips/mt7621, x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>