aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 5.15 to 5.15.93John Audia2023-02-1119-46/+46
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* mediatek: mt7622: fix rootfs/ubi detection for Xiaomi AX6SOleg S2023-02-111-1/+0
| | | | | | | | | | | | | | | | | By specifying the flag "denx,fit" for partition "kernel", the kernel try to find rootfs in the same partition during boot. Reality is that the placement of rootfs is precisely determined by the name of another partition -"ubi". It was also found that on some device (for example devices with NAND chips), the "Denx search engine" manages to find roots at the end of partition "kernel", but such partition doesn't exist and is empty there. Fix this by removing the "denx,fit" flag from partition "kernel". With this change the original behavior of searchif rootfs in partition "ubi" is restored. Signed-off-by: Oleg S <remittor@gmail.com>
* realtek: fix dts whitespaceFelix Baumann2023-02-094-9/+9
| | | | | | Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ramips: fix dts whitespaceFelix Baumann2023-02-096-15/+15
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* mediatek: fix dts whitespaceFelix Baumann2023-02-091-1/+1
| | | | | | Replace blanks with tabs Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* kirkwood: fix dts whitespaceFelix Baumann2023-02-091-1/+1
| | | | | | Replace blanks with tabs Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq807x: fix dts whitespaceFelix Baumann2023-02-091-1/+1
| | | | | | Replace blanks with tabs Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq806x: fix dts whitespaceFelix Baumann2023-02-091-9/+9
| | | | | | Replace blanks with tabs Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* bcm63xx: fix dts whitespaceFelix Baumann2023-02-091-1/+1
| | | | | | Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ath79: fix dts whitespaceFelix Baumann2023-02-096-30/+30
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq40xx: fix dts whitespaceFelix Baumann2023-02-092-2/+2
| | | | | | Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq4019: fix dts white-spaceFelix Baumann2023-02-088-438/+438
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* kernel: bump 5.10 to 5.10.167John Audia2023-02-082-2/+2
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.92John Audia2023-02-082-3/+3
| | | | | | | | | | All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* lantiq: ar9/vr9: add fritz-tffs packageFelix Baumann2023-02-082-8/+12
| | | | | | | Add fritz-tffs package to AVM devices Reorder some devices packages for consistency Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* mpc85xx: p2020: kernel: enable CONFIG_BLK_DEV_NVMEŠimon Bořek2023-02-071-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enables use of NVMe storage devices with appropriate adapter in miniPCIe slots (including for boot) in Turris 1.x routers and possibly NXP P2020RDB boards (these are the only currently supported p2020 devices according to docs[^1]). Proper detection, mountability and readability was proved to be working on Turris 1.1, OpenWrt 21.02 with similar configuration. Increases gzip compressed kernel size by approximately 37 KiB (from 3 703 KiB to 3 740 KiB). Should boot from those devices be possible the driver needs to be built in. Inclusion as a module would prevent this functionality. CONFIG_BLK_DEV_NVME=y Includes NVMe driver in the kernel.[^2] CONFIG_NVME_CORE=y Selected by CONFIG_BLK_DEV_NVME.[^3] Not necessarily needed to be enabled explicitly, but included to match the form of similar functionality implementations for mvebu, x86_64 and rockchip_armv8 targets. CONFIG_NVME_MULTIPATH disabled explicitly to prevent using more space than necessary. [^1]: https://openwrt.org/docs/techref/targets/mpc85xx [^2]: https://cateee.net/lkddb/web-lkddb/BLK_DEV_NVME.html [^3]: https://cateee.net/lkddb/web-lkddb/NVME_CORE.html Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
* mpc85xx: p2020: kernel: refresh configurationŠimon Bořek2023-02-071-5/+15
| | | | | | | 'make kernel_oldconfig CONFIG_TARGET=subtarget' applied to current master Signed-off-by: Šimon Bořek <simon.borek@nic.cz>
* bcm47xx: revert bgmac back to the old limited max frame sizeRafał Miłecki2023-02-072-0/+66
| | | | | | | | | | | | | | Bumping max frame size has significantly affected network performance and memory usage. It was done by upstream commit that first appeared in the 5.7 release. Allocating 512 (BGMAC_RX_RING_SLOTS) buffers, 10 k each, is clearly a bad idea on 32 MiB devices. This commit fixes support for Linksys E1000 V2.1 which gives up after allocating ~346 such buffers running 5.15 kernel. Ref: 230c9da963aa ("bcm53xx: revert bgmac back to the old limited max frame size") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq806x: add missing enclosing reserved-memory block on C2600/AD7200Filip Matijević2023-02-071-8/+10
| | | | | | | | | | | | Most of the time when booting kernel prints a warning from mm/page_alloc.c when pstore/ramoops is being initialized and ramoops is not functional. Fix this by moving ramopps node into reserved-memory block as described in kernel documentation. Fixes: 2964e5024c ("ipq806x: kernel ramoops storage for C2600/AD7200") Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com>
* ipq807x: refresh kernel configRobert Marko2023-02-071-1/+3
| | | | | | | Refresh the ipq807x kernel config to keep it up to date and in sync with the generic one. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: fix assignment of lan port numbers for Cell C RTL30VWCezary Jackiewicz2023-02-061-2/+2
| | | | | | After switching to DSA, the LAN ports in Cell C RTL30VW have swapped numbers. Assigning the right numbers. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ipq806x: onhub: Enable fstools_partname_fallback_scanBrian Norris2023-02-043-9/+3
| | | | | | | | | | | | | | | | | | | | When fstools is unable to parse our root=<...> arg correctly, it can fall back to scanning all block devices for a 'rootfs_data' partition. This fallback was deemed wrong (or at least, a breaking/incompatible change) for some targets, so we're forced to opt back into it with fstools_partname_fallback_scan=1. Without this, OnHub devices will use a rootfs-appended loop device for rootfs_data instead of the intended 3rd partition. While I'm at it, just move all the boot args into the 'cros-vboot' build rule, instead of using the custom bootargs-append. All cros-vboot subtargets here are using the same rootwait (to support both eMMC and USB boot) and root/partition args. Signed-off-by: Brian Norris <computersforpeace@gmail.com> [ drop unrelated comments in commit description ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq807x: remove libwolfsslcpu-crypto dependencyRosen Penev2023-02-041-1/+1
| | | | Signed-off-by: Rosen Penev <rosenp@gmail.com>
* treewide: replace wpad-basic-wolfssl defaultRosen Penev2023-02-0459-143/+143
| | | | | | | The newly merged mbedtls backend is smaller and has fewer ABI related issues than the wolfSSL one. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: mt7621-dts: fix phy-mode of external phy on GB-PC2Arınç ÜNAL2023-02-031-1/+1
| | | | | | | | The phy-mode property must be defined on the MAC instead of the PHY. Define phy-mode under gmac1 which the external phy is connected to. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* x86: add Barracuda Networks F12 interfacesTomasz Maciej Nowak2023-02-031-0/+8
| | | | | | | | | | | | | | | | | | | | Match interface numbers with printed numbers on device enclosure and assign first port as WAN interface. Notes Serial console is available through RJ-45 port with Cisco pinout baud: 19200, parity: none, flow control: none The device is setup with UEFI. To enter setup hold DEL or ESC key on boot. Default UEFI Administrator password is: bcndk1 For users using graphics IC it's advisable to disable display with: i915.disable_display=1 appending to kernel command line inside bootloader, to save about 0.5-0.6W energy on idle. For users not using graphics IC, disable it in UEFI, this will save about 1.5W energy on idle. Pins marked CN19 are ATX power On/Off button. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ramips: mt7621-dts: fix compatible string for mt7530 on TP-Link EAP615-WallArınç ÜNAL2023-02-031-1/+0
| | | | | | | | | | The correct compatible string for the multi-chip module MT7530 switch in MT7621AT, MT7621DAT and MT7621ST SoCs is mediatek,mt7621. Remove the property on TP-Link EAP615-Wall which will default to the said string. Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: use on-flash partition table for Sercomm BZV/CHJJan Hoffmann2023-02-032-8/+330
| | | | | | | | | | | | | | | | | | | These devices have a partition table stored in flash, which compensates for any pre-existing bad blocks by enlarging the respective partition. This means that the current static partition table is only correct for devices without any bad blocks. Typical results of this mismatch are degraded wireless performance and wrong MAC addresses, when the factory partition is shifted due to a bad block somewhere before it. If there is a bad block already before the ubi partition, then OpenWrt may not run at all because the kernel can't find the rootfs. Use the on-flash partition table to fix these issues. Replace the two reserved partitions by the full partition list, as the driver does not allow merging them. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* treewide: strip useless `default n` Kconfig linesTony Butler2023-02-034-6/+0
| | | | | | | | | | Kconfig docs say: > The default value deliberately defaults to 'n' in order to avoid > bloating the build. Apply this rule everywhere, to avoid more cloning of bad examples Signed-off-by: Tony Butler <spudz76@gmail.com>
* ramips: add support for TP-Link Deco M4R v4Mark Ceeha2023-02-034-0/+221
| | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the V4 hardware revision of the Deco M4R. V4 is a complete overhaul of the hardware compared to V1 and V2, and is much more similar to the Archer C6 V3 and C6U V1. Specifications: SoC: MediaTek MT7621AT (2 cores at 880 MHz, 4 threads) RAM: Kingston D1216ECMDXGJD (256 MB) Wireless 2.4 GHz: MediaTek MT7603EN Wireless 5 GHz: MediaTek MT7613BEN Flash: 16 MB SPI NOR Installation: Flash the *-factory.bin image in the U-Boot recovery webserver. You can trigger this webserver by holding the reset button until the LED flashes yellow, or by hooking up to serial pads on the board (clearly labeled GND, RX and TX) and pressing `x` early in boot. Once the factory image has been flashed, you can use the regular upgrade procedure with sysupgrade images for subsequent flashes. Signed-off-by: Mark Ceeha <hi@shiz.me> Tested-by: Mark Ceeha <hi@shiz.me>
* bcm47xx: Refresh kernel 5.15Hauke Mehrtens2023-02-0320-177/+91
| | | | | | | | | | | | | This makes the patches and the kernel configuration apply on top of kernel 5.15. The following patch was removed because the old IDE subsystem was removed from upstream kernel: target/linux/bcm47xx/patches-5.15/610-pci_ide_fix.patch This was tested successfully on a ASUS WL-500g Premium V1. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm47xx: Copy kernel from 5.10 to 5.15Hauke Mehrtens2023-02-0335-0/+3441
| | | | | | | Copy patches and configuration from kernel 5.10 to kernel 5.15 files. No changes were done. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu/uDPU: add quotes to unmount fileRosen Penev2023-02-031-2/+2
| | | | | | This is the last relevant shellcheck warning thrown. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mvebu/uDPU: remove $? usageRosen Penev2023-02-031-12/+18
| | | | | | | shellcheck warns against it with SC2086. It also hides a bug that shellcheck marks with SC2015. Fixed those with explicit if/else. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mvebu/uDPU: remove echo yRosen Penev2023-02-031-2/+2
| | | | | | | It's a bit of a hack. mkfs.ext4 has an -F parameter that does the same thing. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mvebu/uDPU: simplify grep usageRosen Penev2023-02-031-7/+7
| | | | | | | | | | Instead of using the shell's evaluation, use grep's -q parameter. Found with shellcheck's SC2143. Also replaced a head call with grep's -m. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* kernel: bump 5.10 to 5.10.166John Audia2023-02-0316-56/+56
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.91John Audia2023-02-0319-198/+198
| | | | | | | | | | | | | Manually rebased: pending-5.15/103-kbuild-export-SUBARCH.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* mt76: update to the latest version, import WED related mtk_eth_soc patchesFelix Fietkau2023-02-0237-104/+2202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 6c256218e59e wifi: mt76: dma: use napi_build_skb 679254c50f27 mt7915: add CONFIG_MT76_LEDS to cflags 15b9dd6b1b6a wifi: mt76: mt7915: call mt7915_mcu_set_thermal_throttling() only after init_work 8e5c21fe7c5c wifi: mt76: mt7915: rework mt7915_mcu_set_thermal_throttling 87cb74fe42d9 wifi: mt76: mt7915: rework mt7915_thermal_temp_store() c6f24b83eba5 wifi: mt76: mt7915: add error message in mt7915_thermal_set_cur_throttle_state() 99e96b89ee4d wifi: mt76: mt7915: add chip id condition in mt7915_check_eeprom() 833cd420480f wifi: mt76: mt7921: fix channel switch fail in monitor mode f1f8bae6092d wifi: mt76: mt7921: add ack signal support f47087a6dd62 wifi: mt76: mt7996: fix chainmask calculation in mt7996_set_antenna() 2f3b0acc1588 wifi: mt76: mt7996: update register for CFEND_RATE 7e9540dcbd70 wifi: mt76: mt7996: do not hardcode vht beamform cap a37e427d0959 wifi: mt76: connac: fix POWER_CTRL command name typo 98aa346042bd wifi: mt76: mt7915: remove BW160 and BW80+80 support 94fed6a43541 wifi: mt76: mt7921: fix invalid remain_on_channel duration 3c162384d80a wifi: mt76: introduce mt76_queue_is_wed_rx utility routine a409a9454587 wifi: mt76: mt7915: fix memory leak in mt7915_mcu_exit 8b27ecd3a684 wifi: mt76: mt7996: fix memory leak in mt7996_mcu_exit 683760461dd0 wifi: mt76: dma: free rx_head in mt76_dma_rx_cleanup 0c750cf08f85 wifi: mt76: dma: fix memory leak running mt76_dma_tx_cleanup 5de9ae29bea2 wifi: mt76: mt7915: avoid mcu_restart function pointer dad96dd3e62d wifi: mt76: mt7603: avoid mcu_restart function pointer 19d36dd9c8ea wifi: mt76: mt7615: avoid mcu_restart function pointer 6fe2c2383d3d wifi: mt76: mt7921: avoid mcu_restart function pointer 9df89143bf71 wifi: mt76: mt7915: get rid of wed rx_buf_ring page_frag_cache 8d51d11760cb wifi: mt76: fix switch default case in mt7996_reverse_frag0_hdr_trans 0d8057dbd51c wifi: mt76: mt7921u: add support for Comfast CF-952AX ddbf4e933d54 wifi: mt76: mt7915: set sku initial value to zero 06a8904e954e wifi: mt76: mt7915: wed: enable red per-band token drop 724a337caef9 wifi: mt76: mt7915: fix WED TxS reporting 747ca943a5bb wifi: mt76: add flexible polling wait-interval support 133d7859977a wifi: mt76: mt7921: reduce polling time in pmctrl 5fe319a0550e wifi: mt76: add memory barrier to SDIO queue kick 822f060b9d19 wifi: mt76: mt7921: fix rx filter incorrect by drv/fw inconsistent c6794954a723 wifi: mt76: mt7915: fix memory leak in mt7915_mmio_wed_init_rx_buf 9686cd7cc65c wifi: mt76: switch to page_pool allocator 04da4eaa8235 wifi: mt76: enable page_pool stats 1af4a911ebcb wifi: mt76: mt7915: release rxwi in mt7915_wed_release_rx_buf e8c10835cf06 wifi: mt76: fix compile error without CONFIG_PAGE_POOL_STATS 0cf0ede7cc42 net: ethernet: mtk_wed: add reset to rx_ring_setup callback 715b3ed9708a net: ethernet: mtk_wed: add reset to tx_ring_setup callback 9107381d0ff3 wifi: mt76: mt7921: fix error code of return in mt7921_acpi_read 36d2a5bf7802 wifi: mt76: mt7996: rely on mt76_connac2_mac_tx_rate_val c67f57d2cda2 wifi: mt76: dma: add reset to mt76_dma_wed_setup signature 3dace36e2941 wifi: mt76: dma: reset wed queues in mt76_dma_rx_reset 4b229d2da562 wifi: mt76: mt7915: add mt7915 wed reset callbacks f83958376085 wifi: mt76: mt7915: complete wed reset support 321edbb414dc wifi: mt76: mt7996: rely on mt76_connac_txp_common structure bdb7dc38a6d1 wifi: mt76: mt7996: rely on mt76_connac_txp_skb_unmap 8688756305c6 wifi: mt76: mt7996: rely on mt76_connac_tx_complete_skb fbf986dbd4c0 wifi: mt76: mt7996: rely on mt76_connac2_mac_decode_he_radiotap adc556cbce37 wifi: mt76: mt7996: avoid mcu_restart function pointer 5eb4e2303be4 wifi: mt76: remove __mt76_mcu_restart macro e7a61c5f70f5 wifi: mt76: add EHT phy type b375845abc10 wifi: mt76: connac: add CMD_CBW_320MHZ 68b17a243332 wifi: mt76: connac: add helpers for EHT capability 02ec1f61b3a2 wifi: mt76: connac: add cmd id related to EHT support 9209294cd81b wifi: mt76: increase wcid size to 1088 5e85136c9b2f wifi: mt76: add EHT rate stats for ethtool a171f672fdeb wifi: mt76: mt7996: add variants support eda8fd62c105 wifi: mt76: mt7996: add helpers for wtbl and interface limit 4a5a9f4cdc3b wifi: mt76: mt7996: rework capability init 06b73c155680 wifi: mt76: mt7996: add EHT capability init ae71a1b8294f wifi: mt76: mt7996: add support for EHT rate report 65bdfae2991d wifi: mt76: mt7996: enable EHT support in firmware b2360d59747c wifi: mt76: mt7996: add EHT beamforming support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq807x: Enable CPU frequency scaling statsHannu Nyman2023-01-311-1/+1
| | | | | | | Enable the CPU frequency scaling statistics in kernel config. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> Reviewed-by: Robert Marko <robimarko@gmail.com>
* realtek: use generic earlycon setup on 5.15INAGAKI Hiroshi2023-01-309-15/+32
| | | | | | | | | | Use generic earlycon on Linux Kernel instead of initialization in platform setup. And also, drop bootargs with console= parameter from I-O DATA BSH-G24MB. It uses 115200bps as baud-rate, the same as default in rtl838x.dtsi. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
* mxs: switch default kernel to 5.15Zoltan HERPAI2023-01-302-245/+1
| | | | | | | The testing kernel has been available since Mar/2022, let's switch to it by default. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ath25: mark as source-onlyRobert Marko2023-01-301-1/+1
| | | | | | | | | | | | | | | ath25 seems to be a target with low number of users according to download statistics, most of which are for older releases anyway. Users that we managed to find are currently building images downstream as due to low amount of RAM (32MB) default config will not work. Target also suffers from inability for the 5.15 kernel bump to be tested which is a requirment for the next release. So, for those reasons, lets mark it as source-only so that Buildbots dont use the resources for building the images for this target anymore. Signed-off-by: Robert Marko <robimarko@gmail.com>
* zynq: remove kconfig for 5.10Chuanhong Guo2023-01-301-546/+0
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* zynq: switch default kernel to 5.15Nick Hainke2023-01-301-2/+1
| | | | | | | The default kernel should be switched to 5.15 in order to enable testing by a broader audience. Signed-off-by: Nick Hainke <vincent@systemli.org>
* realtek: remove KERNEL_PATCHVER overridesSander Vanheule2023-01-294-8/+0
| | | | | | | | | | On the realtek target, the subtarget makefiles include a KERNEL_PATCHVER setting, shadowing KERNEL_PATCHVER from target/linux/realtek/Makefile. This makes the realtek target an exception in this regard, and makes switching kernel version a bit bothersome. Remove the overrides so all subtargets use the same kernel version. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* kernel: make it possible for packages to select page pool supportFelix Fietkau2023-01-292-0/+22
| | | | | | Will be used by the next mt76 update Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: add fix for a page pool related crash on GROFelix Fietkau2023-01-292-0/+70
| | | | | | Needed for upcoming mt76 page pool support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport page pool fragment support from v5.15Felix Fietkau2023-01-294-4/+802
| | | | | | Required for an upcoming mt76 update Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: fix wrong return code in platform_check_image()Chen Minqiang2023-01-292-1/+2
| | | | | | Ensure that the platform_check_image() function returns an error code. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-02-12 20:52:48 +0000