| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
| |
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug
wireless router with the following specifications:
- CPU: MediaTek MT7628AN 580MHz
- Flash: 8MB
- RAM: 64MB
- Ethernet: 2x 10/100 Mbps (switched)
- 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm
- 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: 4 programmable + LAN, WAN, POWER
- Buttons: reset, WPS
Flashing instructions:
Factory U-boot launches a TFTP client if WPS button is pressed during power-on.
Rename the sysupgrade file and configure a TFTP as follows:
- Client (WL-WN575A3) IP: 192.168.10.101
- Server IP: 192.168.10.100
- Filename: firmware.bin
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
|
|
|
|
|
|
| |
the images were generated for the wrong flash size.
Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
|
|
|
|
|
|
|
|
| |
It's supposed to significantly improve performance but doesn't seem to
affect Northstar unfortunately. It seems only some other platforms were
limited because of this DMA setup mistake.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
| |
The original repo in this Makefile disappeared from the internet so use another
copy of this repository on kernel.org. Also switch from git:// to https://
while being at it.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Port 1 registers the same IO resources as port 2 in the kernel resource
tree, which is wrong.
Fix this by using it's own resources as indicated in the overview
(cns3xxx.h).
Compiled & Tested on several GW2388-4 laguna boards which utilizes all 3
ports.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
| |
disabling some unnecessary code
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
| |
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The patch "build: drop UBI EOF marker from images by default"
(commit d27bce8d28eb129af0abd9c80a7756301b7d588a) removed the
end-of-UBI marker. Without this marker, the boards will panic
during boot:
[ 1.683458] ubi0: attaching mtd4
[ 1.696181] ubi0 warning: scan_peb: valid VID header but corrupted EC header at PEB 31
[ 1.704367] ubi0 error: scan_peb: bad image sequence number 549886691 in PEB 32, expected 184585623
[ 1.713377] Erase counter header dump:
[ 1.717110] magic 0x55424923
[ 1.720843] version 1
[ 1.723797] ec 0
[ 1.726752] vid_hdr_offset 512
[ 1.729880] data_offset 2048
[ 1.733094] image_seq 549886691
[ 1.736740] hdr_crc 0x92ba8130
[ 1.740472] erase counter header hexdump:
[ 1.744493] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd4, error -22
[ 1.751528] UBI error: cannot attach mtd4
[ 1.755373] hctosys: unable to open rtc device (rtc0)
[ 1.761130] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[ 1.768604] Please append a correct "root=" boot option; here are the available partitions:
[...]
[ 1.856992] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[ 1.866519] Rebooting in 1 seconds..Auto calibration ---
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
|
|
|
| |
Fixes a ralink wireless driver related kernel crash as soon as a lot of
data is tranfered via wireless.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- remove not existing properties
- remove properties having the same values as the included dtsi
- remove nodes which are disabled in the included dtsi and not enabled
in dts
- replace the deprecated pinctrl-* compatible strings
- use the same labels for nodes as the included dtsi
- move common used vr9 pci properties to vr9.dtsi
- remove the unused stp node from HomeHub 2B devcie tree source file
- fix spaces vs. tabs and remove superfluous linebreaks
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
| |
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
|
|
|
|
|
|
|
|
| |
This fixes ondemand frequency scaling and moves ipq806x onto upstream driver
Also switching to ondemand frequency scaling as it is fixed now
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
|
|
|
|
|
|
| |
Preparing for cpufreq driver switch to generic cpufreq-dt
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
|
|
|
|
|
|
| |
Preparing for cpufreq driver switch to generic cpufreq-dt
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
|
|
|
|
|
|
| |
leds in correct color accordance - blink power led with white during boot and with amber when flashing firmware - fixed usb leds - enabled unused wps and rfkill leds as wlan leds. Now rfkill led is for 2.4GHz and wps - 5GHz WIFI - removed unneeded bootargs - removed unneeded pci pins from R7800 DT (driver already handles it in proper way) and add tx offsetting - nand ecc step size - fixed sata ports
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
|
|
|
|
|
|
|
| |
The i2c-ramips driver does not work for the MT7628/MT7688 SoCs, the
i2c-mt7621 driver does.
Signed-off-by: Sven Schwermer <sven.schwermer@arcor.de>
|
|
|
|
| |
Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The MikroTik hEX v3 (RB750Gr3) is a MT7621AT board which is similar to most MT7621 reference designs, it can be easily supported by this patch; however, the stock RouterBOOT bootloader has to be replaced by a MT7621 SDK U-Boot such as https://github.com/ndoo/RB750Gr3-U-Boot - U-Boot configured for the RB750Gr3 (16MiB SPI flash, 256MiB DDR3 RAM at 1200MHz).
RouterBOOT, the stock bootloader, does not initialize the UART and boots silently, making it preferable to replace it with a MT7621 SDK U-Boot with UART (57600 8N1) that supports HTTP, TFTP or serial upload of sysupgrade firmware and U-Boot.
Furthermore, RouterOS, the stock firmware, is contained in a proprietary modification of SquashFS without GPL sources; UART is also disabled in stock firmware.
The combination of LEDE firmware generated by this PR and MT7621 SDK U-Boot expects the printed MAC address to reside at offset `0xe000` of the factory partition (absolute offset is `0x4e000`); this is similar to the factory MAC address offset for several other MT7621 devices.
A 16MiB flash dump suitable for use with flashrom will be provided if/once this patch is accepted and binaries are built by LEDE buildbot. Alternatively, writing the U-Boot to the SPI flash starting at 0x0 offset and booting the board with serial console attached will allow TFTP, HTTP or serial upload of sysupgrade firmware.
Signed-off-by: Andrew Yong <me@ndoo.sg>
|
|
|
|
|
|
|
|
|
|
| |
This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches.
Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood.
Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed
by P. Wassi).
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
|
|
|
|
|
|
|
| |
This patch adds the kmod-usb3 and kmod-usb-ledtrig-usbport packages to the
DIR-860L B1 profile. The DIR-860L B1 has a USB 3 port.
Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
|
|
|
|
| |
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.
LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.
The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.
LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.
64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.
All of 4.4 kernel patches porting from SDK release or upstream.
QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX
Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
|
|
|
|
|
|
|
|
|
|
|
| |
- setting read-only flag to important partitions
- enabling PA to improve 2.4 GHz signal strength
- add missing leds
- rename colour led
- add mac adress to 5GHz wlan interface
- included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h>
Signed-off-by: Henryk Heisig hyniu@o2.pl
|
|
|
|
|
|
|
|
|
| |
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 064f467264c5c9b6eca0bb96b587f9412b770cc5)
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit eb0ce57270d0b5b81b224b9336cf54707497eede)
Modified after cherry-pick:
obj in Makefile
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Created minimal patchset based on BB rev 43158 by Eddi De Pieri
14.07/openwrt.git 79472c025449efae9310defad0d3a73cff14d756
If the VR9 based router provides FXS ports and they shoud enabled then
the following must added to the kernel command line:
mem=[TOTALMEMSIZE-2M] vpe1_load_addr=ADDRESS vpe1_mem=2M maxvpes=1
maxtcs=1
To use FXS 2M of RAM are needed for the VPE firmware. The size is set
by vpe1_mem.
The available RAM must be reduced by this size using the mem argument.
A correct load address (example 0x83e00000) for the firmware must be given,
too.
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
(required not-distributable firmware blob - dump it by yourself from original firmware)
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
(cherry picked from commit 8d924d43c0ea6839a3a33e54982e8da48b736001)
Modified after cherry-pick:
compatible attribute
Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
|
|
|
|
|
|
| |
KERNEL BUG: BAD_PAGE_STATE in process appears here and there during intensive memory usage.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
|
|
|
|
|
|
|
| |
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
|
|
|
|
| |
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
|
|
|
|
|
|
| |
add blank lines and use macros for GPIOs
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
|
|
|
|
|
|
|
|
| |
Refresh patches for all targets that support kernel 4.4.
compile/run-tested on ar71xx, brcm47xx, kirkwood.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
|
| |
This fixes the build of the ipq806x target.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
| |
Both the MR12 and MR16 are single gigabit ethernet devices, similar to the
MR18. This change gives them the correct network config on a fresh install.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
[Jo-Philipp Wich: adjust for alphabetical ordering, line wrap commit msg]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
|
|
|
|
|
|
|
|
|
| |
In 814d70b2 the member mac06_exchange_en of struct
ar8327_pad_cfg was changed to mac06_exchange_dis,
but wpj344 was not adopted to stay in sync.
Signed-off-by: Christian Mehlis <christian@m3hlis.de>
Reported-by: Nick Dennis <ndennis@rapiduswireless.com>
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
| |
Thanks to leaving .pattern file we can easily insert extra step between
linksys-pattern-partition and trx-v2-with-loader, e.g. rootfs one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
|
| |
The old usbdev trigger never supported assigning more than 1 USB port.
This code we got was never working as expected and it was missing 2 more
ports. Switch to usbport to have LED working with all ports.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
|
|
|
|
|
|
|
|
|
| |
Fixes the same hctosys init issue as described in commit
5481ce9a1157a43d8b2c963e03fb243e70974361
The Gateworks Ventana family uses an emulated Dallas 1672
RTC device.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
|
|
|
|
|
| |
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
|
|
|
|
|
| |
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
|
|
|
|
|
| |
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
|
|
|
|
|
|
|
|
| |
Support splitting WRGG images, found in some D-Link devices (e.g.
DAP-2695).
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: John Crispin <john@phrozen.org>
|
|
|
|
| |
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|