aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 5.10 to 5.10.150John Audia2022-11-0133-280/+132
| | | | | | | | | | | | Manually rebased: bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me> [Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit aa2fa2eb76f13e48cd39d844dca34627da00cb5d)
* ramips: Correct Unielec 01 and 06 dts wan macaddr byte locationDavid Bentham2022-10-303-6/+6
| | | | | | | | | | | Recent backport patch b5cb5f352d3133ac8384275be7d47264ad135e74 had missed changing the macaddr_factory address location. This patch corrects the address location. Fixes: b5cb5f352d31 ("ramips: fix WAN mac address allocation for Unielec 01 and 06 models") Signed-off-by: David Bentham <db260179@gmail.com> [Fix dts node name too] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm4908: backport bcm4908_enet fix for NULL dereferenceRafał Miłecki2022-10-284-4/+103
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 31e4e566545e53594bafe846c170a5d2fa6821e3)
* bcm4908: optimize Ethernet driver by using build_skb()Rafał Miłecki2022-10-281-0/+152
| | | | | | | | This should slightly improve performance thanks to the better cache usage. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 6a02205a4d94a7b6a888ec55d1aecd60ebb20d77)
* kernel: mtd: backport SafeLoader parserRafał Miłecki2022-10-279-5/+239
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 711f1a8bcbdde1ee9e2934d707fb1765fc644268)
* kernel: mtd: backport extended dynamic partitions supportRafał Miłecki2022-10-277-5/+154
| | | | | | | | This gets rid of "nvmem-cells" limitation. Dynamic partitions can be defined for any (sub)partitions layout. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 4eda414b09c790344e47c1cebe78e5433b4dc10d)
* ath79: fix reference clock for RouterBoard 912UAGPavel Kamaev2022-10-231-1/+1
| | | | | | | | | | | This fixes reference clock frequency of RB912. 25 MHz frequency leads to system clock running too fast, uptime incrementing too fast and delays (like `sleep 10`) returning too early. Board has quartz with NSK 3KHAA Z 40 000 marking. Signed-off-by: Pavel Kamaev <pavel@kamaev.me> (cherry picked from commit a716ac55649707e8279de6f2ea66c7f6060c982c)
* ramips: fix WAN mac address allocation for Unielec 01 and 06 modelsDavid Bentham2022-10-233-6/+15
| | | | | | | | | | | | | | | | | | | | | | | Manufacturer has predetermined mac address values for lan and wan ports. This change keeps inline with other mt7621 devices mac address allocation from factory mtd partition. Example from hexdump output: 0xe000 0x6 (lan) - 0xe006 0x6 (wan) 0000e000 70 b3 d5 10 02 96 70 b3 d5 10 02 95 ff ff ff ff Previous change had created an overlapping mac address situation as it would increment by one based on the lan mac address location found in the factory partition, which would sometimes increment to the same as the mt7603 wifi chip. Tested on Unielec u7621-01 model Signed-off-by: David Bentham <db260179@gmail.com> (cherry picked from commit 67660d36674c8c1504cbf3cd199409d0b209f802)
* ramips: rt3883: enable lzma-loader for Belkin F9K1109v1Robert Senderek2022-10-231-1/+1
| | | | | | | | Fixes boot loader LZMA decompression issues Fixes: #10968 Signed-off-by: Robert Senderek <robert.senderek@10g.pl> (cherry picked from commit ac296f621058119501ccd54e7cb2a243af5dc5a0)
* ramips: mt7621: enable lzma-loader for Asus RT-N56U-B1Alex Khodin2022-10-231-0/+1
| | | | | | | | | Fixes boot loader LZMA decompression issues. Without this change the board end up in a boot loop. Signed-off-by: Alex Khodin <mxktz1@gmail.com> (cherry picked from commit f6099d797460b23e06fb0c391606346993b4593e)
* bcm53xx: enable Broadcom 4366b1 firmware for Asus RT-AC88UArınç ÜNAL2022-10-231-1/+1
| | | | | | | | | | | | | On some of the hardware revisions of Asus RT-AC88U, brcmfmac detects the 4366b1 wireless chip and tries to load the firmware file which doesn't exist because it's not included in the image. Therefore, include firmware for 4366b1 along with 4366c0. This way, all hardware revisions of the router will be supported by having brcmfmac use the firmware file for the wireless chip it detects. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit 2b9bb5b187022f8b64c84781c071d6c2b0ce3e45)
* octeon: fix imagebuilder generation by introducing generic targetNick Hainke2022-10-232-5/+5
| | | | | | | | | | | | | | The generic imagebuilder does not have a generic in the name, although this is the default naming scheme. Use bcm53xx as template for this fix. Before the fix: openwrt-imagebuilder-octeon.Linux-x86_64.tar.xz After: openwrt-imagebuilder-octeon-generic.Linux-x86_64.tar.xz Signed-off-by: Nick Hainke <vincent@systemli.org> (cherry picked from commit a67f484e67b1d0930cb4b10b9e3787ecf7e71579)
* ath79: support Ruckus ZoneFlex 7321Lech Perczak2022-10-233-0/+63
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ruckus ZoneFlex 7321 is a dual-band, single radio 802.11n 2x2 MIMO enterprise access point. It is very similar to its bigger brother, ZoneFlex 7372. Hardware highligts: - CPU: Atheros AR9342 SoC at 533 MHz - RAM: 64MB DDR2 - Flash: 32MB SPI-NOR - Wi-Fi: AR9342 built-in dual-band 2x2 MIMO radio - Ethernet: single Gigabit Ethernet port through AR8035 gigabit PHY - PoE: input through Gigabit port - Standalone 12V/1A power input - USB: optional single USB 2.0 host port on the 7321-U variant. Serial console: 115200-8-N-1 on internal H1 header. Pinout: H1 ---------- |1|x3|4|5| ---------- Pin 1 is near the "H1" marking. 1 - RX x - no pin 3 - VCC (3.3V) 4 - GND 5 - TX JTAG: Connector H5, unpopulated, similar to MIPS eJTAG, standard, but without the key in pin 12 and not every pin routed: ------- H5 |1 |2 | ------- |3 |4 | ------- |5 |6 | ------- |7 |8 | ------- |9 |10| ------- |11|12| ------- |13|14| ------- 3 - TDI 5 - TDO 7 - TMS 9 - TCK 2,4,6,8,10 - GND 14 - Vref 1,11,12,13 - Not connected Installation: There are two methods of installation: - Using serial console [1] - requires some disassembly, 3.3V USB-Serial adapter, TFTP server, and removing a single T10 screw, but with much less manual steps, and is generally recommended, being safer. - Using stock firmware root shell exploit, SSH and TFTP [2]. Does not work on some rare versions of stock firmware. A more involved, and requires installing `mkenvimage` from u-boot-tools package if you choose to rebuild your own environment, but can be used without disassembly or removal from installation point, if you have the credentials. If for some reason, size of your sysupgrade image exceeds 13312kB, proceed with method [1]. For official images this is not likely to happen ever. [1] Using serial console: 0. Connect serial console to H1 header. Ensure the serial converter does not back-power the board, otherwise it will fail to boot. 1. Power-on the board. Then quickly connect serial converter to PC and hit Ctrl+C in the terminal to break boot sequence. If you're lucky, you'll enter U-boot shell. Then skip to point 3. Connection parameters are 115200-8-N-1. 2. Allow the board to boot. Press the reset button, so the board reboots into U-boot again and go back to point 1. 3. Set the "bootcmd" variable to disable the dual-boot feature of the system and ensure that uImage is loaded. This is critical step, and needs to be done only on initial installation. > setenv bootcmd "bootm 0x9f040000" > saveenv 4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed: > setenv serverip 192.168.1.2 > setenv ipaddr 192.168.1.1 > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7321-initramfs-kernel.bin > bootm 0x81000000 5. Optional, but highly recommended: back up contents of "firmware" partition: $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7321_fw1_backup.bin $ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7321_fw2_backup.bin 6. Copy over sysupgrade image, and perform actual installation. OpenWrt shall boot from flash afterwards: $ ssh root@192.168.1.1 # sysupgrade -n openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin [2] Using stock root shell: 0. Reset the device to factory defaullts. Power-on the device and after it boots, hold the reset button near Ethernet connectors for 5 seconds. 1. Connect the device to the network. It will acquire address over DHCP, so either find its address using list of DHCP leases by looking for label MAC address, or try finding it by scanning for SSH port: $ nmap 10.42.0.0/24 -p22 From now on, we assume your computer has address 10.42.0.1 and the device has address 10.42.0.254. 2. Set up a TFTP server on your computer. We assume that TFTP server root is at /srv/tftp. 3. Obtain root shell. Connect to the device over SSH. The SSHD ond the frmware is pretty ancient and requires enabling HMAC-MD5. $ ssh 10.42.0.254 \ -o UserKnownHostsFile=/dev/null \ -o StrictHostKeyCheking=no \ -o MACs=hmac-md5 Login. User is "super", password is "sp-admin". Now execute a hidden command: Ruckus It is case-sensitive. Copy and paste the following string, including quotes. There will be no output on the console for that. ";/bin/sh;" Hit "enter". The AP will respond with: grrrr OK Now execute another hidden command: !v54! At "What's your chow?" prompt just hit "enter". Congratulations, you should now be dropped to Busybox shell with root permissions. 4. Optional, but highly recommended: backup the flash contents before installation. At your PC ensure the device can write the firmware over TFTP: $ sudo touch /srv/tftp/ruckus_zf7321_firmware{1,2}.bin $ sudo chmod 666 /srv/tftp/ruckus_zf7321_firmware{1,2}.bin Locate partitions for primary and secondary firmware image. NEVER blindly copy over MTD nodes, because MTD indices change depending on the currently active firmware, and all partitions are writable! # grep rcks_wlan /proc/mtd Copy over both images using TFTP, this will be useful in case you'd like to return to stock FW in future. Make sure to backup both, as OpenWrt uses bot firmwre partitions for storage! # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7321_firmware1.bin -p 10.42.0.1 # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7321_firmware2.bin -p 10.42.0.1 When the command finishes, copy over the dump to a safe place for storage. $ cp /srv/tftp/ruckus_zf7321_firmware{1,2}.bin ~/ 5. Ensure the system is running from the BACKUP image, i.e. from rcks_wlan.bkup partition or "image 2". Otherwise the installation WILL fail, and you will need to access mtd0 device to write image which risks overwriting the bootloader, and so is not covered here and not supported. Switching to backup firmware can be achieved by executing a few consecutive reboots of the device, or by updating the stock firmware. The system will boot from the image it was not running from previously. Stock firmware available to update was conveniently dumped in point 4 :-) 6. Prepare U-boot environment image. Install u-boot-tools package. Alternatively, if you build your own images, OpenWrt provides mkenvimage in host staging directory as well. It is recommended to extract environment from the device, and modify it, rather then relying on defaults: $ sudo touch /srv/tftp/u-boot-env.bin $ sudo chmod 666 /srv/tftp/u-boot-env.bin On the device, find the MTD partition on which environment resides. Beware, it may change depending on currently active firmware image! # grep u-boot-env /proc/mtd Now, copy over the partition # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1 Store the stock environment in a safe place: $ cp /srv/tftp/u-boot-env.bin ~/ Extract the values from the dump: $ strings u-boot-env.bin | tee u-boot-env.txt Now clean up the debris at the end of output, you should end up with each variable defined once. After that, set the bootcmd variable like this: bootcmd=bootm 0x9f040000 You should end up with something like this: bootcmd=bootm 0x9f040000 bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init baudrate=115200 ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup) mtdids=nor0=ar7100-nor0 bootdelay=2 ethact=eth0 filesize=78a000 fileaddr=81000000 partition=nor0,0 mtddevnum=0 mtddevname=u-boot ipaddr=10.0.0.1 serverip=10.0.0.5 stdin=serial stdout=serial stderr=serial These are the defaults, you can use most likely just this as input to mkenvimage. Now, create environment image and copy it over to TFTP root: $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt $ sudo cp u-boot-env.bin /srv/tftp This is the same image, gzipped and base64-encoded: H4sIAAAAAAAAA+3QQW7TQBQAUF8EKRtQI6XtJDS0VJoN4gYcAE3iCbWS2MF2Sss1ORDYqVq6YMEB3rP0 Z/7Yf+aP3/56827VNP16X8Zx3E/Cw8dNuAqDYlxI7bcurpu6a3Y59v3jlzCbz5eLECbt8HbT9Y+HHLvv x9TdbbpJVVd9vOxWVX05TotVOpZt6nN8qilyf5fKso3hIYTb8JDSEFarIazXQyjLIeRc7PvykNq+iy+T 1F7PQzivmzbcLpYftmfH87G56Wz+/v18sT1r19vu649dqi/2qaqns0W4utmelalPm27I/lac5/p+OluO NZ+a1JaTz8M3/9hmtT0epmMjVdnF8djXLZx+TJl36TEuTlda93EYQrGpdrmrfuZ4fZPGHzjmp/vezMNJ MV6n6qumPm06C+MRZb6vj/v4Mk/7HJ+6LarDqXweLsZnXnS5vc9tdXheWRbd0GIdh/Uq7cakOfavsty2 z1nxGwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAD+1x9eTkHLAAAEAA== 7. Perform actual installation. Copy over OpenWrt sysupgrade image to TFTP root: $ sudo cp openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin /srv/tftp Now load both to the device over TFTP: # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1 # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin -g 10.42.0.1 Vverify checksums of both images to ensure the transfer over TFTP was completed: # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin And compare it against source images: $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7321-squashfs-sysupgrade.bin Locate MTD partition of the primary image: # grep rcks_wlan.main /proc/mtd Now, write the images in place. Write U-boot environment last, so unit still can boot from backup image, should power failure occur during this. Replace MTD placeholders with real MTD nodes: # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd> # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd> Finally, reboot the device. The device should directly boot into OpenWrt. Look for the characteristic power LED blinking pattern. # reboot -f After unit boots, it should be available at the usual 192.168.1.1/24. Return to factory firmware: 1. Boot into OpenWrt initramfs as for initial installation. To do that without disassembly, you can write an initramfs image to the device using 'sysupgrade -F' first. 2. Unset the "bootcmd" variable: fw_setenv bootcmd "" 3. Write factory images downloaded from manufacturer website into fwconcat0 and fwconcat1 MTD partitions, or restore backup you took before installation: mtd write ruckus_zf7321_fw1_backup.bin /dev/mtd1 mtd write ruckus_zf7321_fw2_backup.bin /dev/mtd5 4. Reboot the system, it should load into factory firmware again. Quirks and known issues: - Flash layout is changed from the factory, to use both firmware image partitions for storage using mtd-concat, and uImage format is used to actually boot the system, which rules out the dual-boot capability. - The 5GHz radio has its own EEPROM on board, not connected to CPU. - The stock firmware has dual-boot capability, which is not supported in OpenWrt by choice. It is controlled by data in the top 64kB of RAM which is unmapped, to avoid the interference in the boot process and accidental switch to the inactive image, although boot script presence in form of "bootcmd" variable should prevent this entirely. - U-boot disables JTAG when starting. To re-enable it, you need to execute the following command before booting: mw.l 1804006c 40 And also you need to disable the reset button in device tree if you intend to debug Linux, because reset button on GPIO0 shares the TCK pin. - On some versions of stock firmware, it is possible to obtain root shell, however not much is available in terms of debugging facitilies. 1. Login to the rkscli 2. Execute hidden command "Ruckus" 3. Copy and paste ";/bin/sh;" including quotes. This is required only once, the payload will be stored in writable filesystem. 4. Execute hidden command "!v54!". Press Enter leaving empty reply for "What's your chow?" prompt. 5. Busybox shell shall open. Source: https://alephsecurity.com/vulns/aleph-2019014 Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit f1d112ee5a43e8c4a22db05b94bbcd0677a34486)
* ath79: support Ruckus ZoneFlex 7372Lech Perczak2022-10-235-0/+355
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ruckus ZoneFlex 7372 is a dual-band, dual-radio 802.11n 2x2 MIMO enterprise access point. Ruckus ZoneFlex 7352 is also supported, lacking the 5GHz radio part. Hardware highligts: - CPU: Atheros AR9344 SoC at 560 MHz - RAM: 128MB DDR2 - Flash: 32MB SPI-NOR - Wi-Fi 2.4GHz: AR9344 built-in 2x2 MIMO radio - Wi-Fi 5Ghz: AR9582 2x2 MIMO radio (Only in ZF7372) - Antennas: - Separate internal active antennas with beamforming support on both bands with 7 elements per band, each controlled by 74LV164 GPIO expanders, attached to GPIOs of each radio. - Two dual-band external RP-SMA antenna connections on "7372-E" variant. - Ethernet 1: single Gigabit Ethernet port through AR8035 gigabit PHY - Ethernet 2: single Fast Ethernet port through AR9344 built-in switch - PoE: input through Gigabit port - Standalone 12V/1A power input - USB: optional single USB 2.0 host port on "-U" variants. The same image should support: - ZoneFlex 7372E (variant with external antennas, without beamforming capability) - ZoneFlex 7352 (single-band, 2.4GHz-only variant). which are based on same baseboard (codename St. Bernard), with different populated components. Serial console: 115200-8-N-1 on internal H1 header. Pinout: H1 --- |5| --- |4| --- |3| --- |x| --- |1| --- Pin 5 is near the "H1" marking. 1 - RX x - no pin 3 - VCC (3.3V) 4 - GND 5 - TX JTAG: Connector H2, similar to MIPS eJTAG, standard, but without the key in pin 12 and not every pin routed: ------- H2 |1 |2 | ------- |3 |4 | ------- |5 |6 | ------- |7 |8 | ------- |9 |10| ------- |11|12| ------- |13|14| ------- 3 - TDI 5 - TDO 7 - TMS 9 - TCK 2,4,6,8,10 - GND 14 - Vref 1,11,12,13 - Not connected Installation: There are two methods of installation: - Using serial console [1] - requires some disassembly, 3.3V USB-Serial adapter, TFTP server, and removing a single T10 screw, but with much less manual steps, and is generally recommended, being safer. - Using stock firmware root shell exploit, SSH and TFTP [2]. Does not work on some rare versions of stock firmware. A more involved, and requires installing `mkenvimage` from u-boot-tools package if you choose to rebuild your own environment, but can be used without disassembly or removal from installation point, if you have the credentials. If for some reason, size of your sysupgrade image exceeds 13312kB, proceed with method [1]. For official images this is not likely to happen ever. [1] Using serial console: 0. Connect serial console to H1 header. Ensure the serial converter does not back-power the board, otherwise it will fail to boot. 1. Power-on the board. Then quickly connect serial converter to PC and hit Ctrl+C in the terminal to break boot sequence. If you're lucky, you'll enter U-boot shell. Then skip to point 3. Connection parameters are 115200-8-N-1. 2. Allow the board to boot. Press the reset button, so the board reboots into U-boot again and go back to point 1. 3. Set the "bootcmd" variable to disable the dual-boot feature of the system and ensure that uImage is loaded. This is critical step, and needs to be done only on initial installation. > setenv bootcmd "bootm 0x9f040000" > saveenv 4. Boot the OpenWrt initramfs using TFTP. Replace IP addresses as needed: > setenv serverip 192.168.1.2 > setenv ipaddr 192.168.1.1 > tftpboot 0x81000000 openwrt-ath79-generic-ruckus_zf7372-initramfs-kernel.bin > bootm 0x81000000 5. Optional, but highly recommended: back up contents of "firmware" partition: $ ssh root@192.168.1.1 cat /dev/mtd1 > ruckus_zf7372_fw1_backup.bin $ ssh root@192.168.1.1 cat /dev/mtd5 > ruckus_zf7372_fw2_backup.bin 6. Copy over sysupgrade image, and perform actual installation. OpenWrt shall boot from flash afterwards: $ ssh root@192.168.1.1 # sysupgrade -n openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin [2] Using stock root shell: 0. Reset the device to factory defaullts. Power-on the device and after it boots, hold the reset button near Ethernet connectors for 5 seconds. 1. Connect the device to the network. It will acquire address over DHCP, so either find its address using list of DHCP leases by looking for label MAC address, or try finding it by scanning for SSH port: $ nmap 10.42.0.0/24 -p22 From now on, we assume your computer has address 10.42.0.1 and the device has address 10.42.0.254. 2. Set up a TFTP server on your computer. We assume that TFTP server root is at /srv/tftp. 3. Obtain root shell. Connect to the device over SSH. The SSHD ond the frmware is pretty ancient and requires enabling HMAC-MD5. $ ssh 10.42.0.254 \ -o UserKnownHostsFile=/dev/null \ -o StrictHostKeyCheking=no \ -o MACs=hmac-md5 Login. User is "super", password is "sp-admin". Now execute a hidden command: Ruckus It is case-sensitive. Copy and paste the following string, including quotes. There will be no output on the console for that. ";/bin/sh;" Hit "enter". The AP will respond with: grrrr OK Now execute another hidden command: !v54! At "What's your chow?" prompt just hit "enter". Congratulations, you should now be dropped to Busybox shell with root permissions. 4. Optional, but highly recommended: backup the flash contents before installation. At your PC ensure the device can write the firmware over TFTP: $ sudo touch /srv/tftp/ruckus_zf7372_firmware{1,2}.bin $ sudo chmod 666 /srv/tftp/ruckus_zf7372_firmware{1,2}.bin Locate partitions for primary and secondary firmware image. NEVER blindly copy over MTD nodes, because MTD indices change depending on the currently active firmware, and all partitions are writable! # grep rcks_wlan /proc/mtd Copy over both images using TFTP, this will be useful in case you'd like to return to stock FW in future. Make sure to backup both, as OpenWrt uses bot firmwre partitions for storage! # tftp -l /dev/<rcks_wlan.main_mtd> -r ruckus_zf7372_firmware1.bin -p 10.42.0.1 # tftp -l /dev/<rcks_wlan.bkup_mtd> -r ruckus_zf7372_firmware2.bin -p 10.42.0.1 When the command finishes, copy over the dump to a safe place for storage. $ cp /srv/tftp/ruckus_zf7372_firmware{1,2}.bin ~/ 5. Ensure the system is running from the BACKUP image, i.e. from rcks_wlan.bkup partition or "image 2". Otherwise the installation WILL fail, and you will need to access mtd0 device to write image which risks overwriting the bootloader, and so is not covered here and not supported. Switching to backup firmware can be achieved by executing a few consecutive reboots of the device, or by updating the stock firmware. The system will boot from the image it was not running from previously. Stock firmware available to update was conveniently dumped in point 4 :-) 6. Prepare U-boot environment image. Install u-boot-tools package. Alternatively, if you build your own images, OpenWrt provides mkenvimage in host staging directory as well. It is recommended to extract environment from the device, and modify it, rather then relying on defaults: $ sudo touch /srv/tftp/u-boot-env.bin $ sudo chmod 666 /srv/tftp/u-boot-env.bin On the device, find the MTD partition on which environment resides. Beware, it may change depending on currently active firmware image! # grep u-boot-env /proc/mtd Now, copy over the partition # tftp -l /dev/mtd<N> -r u-boot-env.bin -p 10.42.0.1 Store the stock environment in a safe place: $ cp /srv/tftp/u-boot-env.bin ~/ Extract the values from the dump: $ strings u-boot-env.bin | tee u-boot-env.txt Now clean up the debris at the end of output, you should end up with each variable defined once. After that, set the bootcmd variable like this: bootcmd=bootm 0x9f040000 You should end up with something like this: bootcmd=bootm 0x9f040000 bootargs=console=ttyS0,115200 rootfstype=squashfs init=/sbin/init baudrate=115200 ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee bootdelay=2 mtdids=nor0=ar7100-nor0 mtdparts=mtdparts=ar7100-nor0:256k(u-boot),13312k(rcks_wlan.main),2048k(datafs),256k(u-boot-env),512k(Board Data),13312k(rcks_wlan.bkup) ethact=eth0 filesize=1000000 fileaddr=81000000 ipaddr=192.168.0.7 serverip=192.168.0.51 partition=nor0,0 mtddevnum=0 mtddevname=u-boot stdin=serial stdout=serial stderr=serial These are the defaults, you can use most likely just this as input to mkenvimage. Now, create environment image and copy it over to TFTP root: $ mkenvimage -s 0x40000 -b -o u-boot-env.bin u-boot-env.txt $ sudo cp u-boot-env.bin /srv/tftp This is the same image, gzipped and base64-encoded: H4sIAAAAAAAAA+3QTW7TQBQAYB+AQ2TZSGk6Tpv+SbNBrNhyADSJHWolsYPtlJaDcAWOCXaqQhdIXOD7 Fm/ee+MZ+/nHu58fV03Tr/dFHNf9JDzdbcJVGGRjI7Vfurhu6q7ZlbHvnz+FWZ4vFyFM2mF30/XPhzJ2 X4+pe9h0k6qu+njRrar6YkyzVToWberL+HImK/uHVBRtDE8h3IenlIawWg1hvR5CUQyhLE/vLcpdeo6L bN8XVdHFumlDTO1NHsL5mI/9Q2r7Lv5J3uzeL5bX27Pj+XjRdJZfXuaL7Vm73nafv+1SPd+nqp7OFuHq dntWpD5tuqH6e+K8rB+ns+V45n2T2mLyYXjmH9estsfD9DTSuo/DErJNtSu76vswbjg5NU4D3752qsOp zu8W8/z6dh7mN1lXto9lWx3eNJd5Ng5V9VVTn2afnSYuysf6uI9/8rQv48s3Z93wn+o4XFWl3Vg0x/5N Vbbta5X9AgAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAID/+Q2Z/B7cAAAEAA== 7. Perform actual installation. Copy over OpenWrt sysupgrade image to TFTP root: $ sudo cp openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin /srv/tftp Now load both to the device over TFTP: # tftp -l /tmp/u-boot-env.bin -r u-boot-env.bin -g 10.42.0.1 # tftp -l /tmp/openwrt.bin -r openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin -g 10.42.0.1 Verify checksums of both images to ensure the transfer over TFTP was completed: # sha256sum /tmp/u-boot-env.bin /tmp/openwrt.bin And compare it against source images: $ sha256sum /srv/tftp/u-boot-env.bin /srv/tftp/openwrt-ath79-generic-ruckus_zf7372-squashfs-sysupgrade.bin Locate MTD partition of the primary image: # grep rcks_wlan.main /proc/mtd Now, write the images in place. Write U-boot environment last, so unit still can boot from backup image, should power failure occur during this. Replace MTD placeholders with real MTD nodes: # flashcp /tmp/openwrt.bin /dev/<rcks_wlan.main_mtd> # flashcp /tmp/u-boot-env.bin /dev/<u-boot-env_mtd> Finally, reboot the device. The device should directly boot into OpenWrt. Look for the characteristic power LED blinking pattern. # reboot -f After unit boots, it should be available at the usual 192.168.1.1/24. Return to factory firmware: 1. Boot into OpenWrt initramfs as for initial installation. To do that without disassembly, you can write an initramfs image to the device using 'sysupgrade -F' first. 2. Unset the "bootcmd" variable: fw_setenv bootcmd "" 3. Write factory images downloaded from manufacturer website into fwconcat0 and fwconcat1 MTD partitions, or restore backup you took before installation: mtd write ruckus_zf7372_fw1_backup.bin /dev/mtd1 mtd write ruckus_zf7372_fw2_backup.bin /dev/mtd5 4. Reboot the system, it should load into factory firmware again. Quirks and known issues: - This is first device in ath79 target to support link state reporting on FE port attached trough the built-in switch. - Flash layout is changed from the factory, to use both firmware image partitions for storage using mtd-concat, and uImage format is used to actually boot the system, which rules out the dual-boot capability. The 5GHz radio has its own EEPROM on board, not connected to CPU. - The stock firmware has dual-boot capability, which is not supported in OpenWrt by choice. It is controlled by data in the top 64kB of RAM which is unmapped, to avoid the interference in the boot process and accidental switch to the inactive image, although boot script presence in form of "bootcmd" variable should prevent this entirely. - U-boot disables JTAG when starting. To re-enable it, you need to execute the following command before booting: mw.l 1804006c 40 And also you need to disable the reset button in device tree if you intend to debug Linux, because reset button on GPIO0 shares the TCK pin. - On some versions of stock firmware, it is possible to obtain root shell, however not much is available in terms of debugging facitilies. 1. Login to the rkscli 2. Execute hidden command "Ruckus" 3. Copy and paste ";/bin/sh;" including quotes. This is required only once, the payload will be stored in writable filesystem. 4. Execute hidden command "!v54!". Press Enter leaving empty reply for "What's your chow?" prompt. 5. Busybox shell shall open. Source: https://alephsecurity.com/vulns/aleph-2019014 - Stock firmware has beamforming functionality, known as BeamFlex, using active multi-segment antennas on both bands - controlled by RF analog switches, driven by a pair of 74LV164 shift registers. Shift registers used for each radio are connected to GPIO14 (clock) and GPIO15 of the respective chip. They are mapped as generic GPIOs in OpenWrt - in stock firmware, they were most likely handled directly by radio firmware, given the real-time nature of their control. Lack of this support in OpenWrt causes the antennas to behave as ordinary omnidirectional antennas, and does not affect throughput in normal conditions, but GPIOs are available to tinker with nonetheless. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit 59cb4dc91d500edc2e6b462e223e367806557cc5)
* kernel: mtd: fix unbalanced of_node_put() in dynamic partitions codeRafał Miłecki2022-10-211-0/+101
| | | | | | Fixes: cae4d089bc1d3 ("kernel: backport mtd dynamic partition patch") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 76a470d5df971bd4c7309480a585d7fbaef63621)
* kernel: bump 5.10 to 5.10.147John Audia2022-10-1816-108/+36
| | | | | | | | | | | | Removed upstreamed: bcm53xx/patches-5.10/083-v6.0-clk-iproc-Do-not-rely-on-node-name-for-correct-PLL-s.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.147&id=a8e6cde5062fb2aff81f86cc0770591714bee545 Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit e2da6a0a59a81a4fc0fdffde31abf22ee121e9f5)
* mt7621: hiwifi_hc5962: fix reboot loop by using LZMA loaderPetr Štetiar2022-10-181-0/+1
| | | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. References: https://github.com/openwrt/openwrt/issues/10645#issuecomment-1282607274 Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit b63d6d4730fd0dc30ce6707338c398e8b9d61d86)
* mt7621: netgear_ex6150: fix reboot loop by using LZMA loaderPetr Štetiar2022-10-181-0/+1
| | | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #10645 Signed-off-by: Petr Štetiar <ynezz@true.cz> (cherry picked from commit 7dd1cab1c16f374716b1ee7a5bf99f849b74c1dc)
* mpc85xx: p1010: make TP-Link WDR4900 v1 build againMatthias Schiffer2022-10-141-3/+17
| | | | | | | | Add the spi-loader as a pre-kernel stage, so we can lift the kernel size limit. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit 2fa53c9214b7b93fd82ad1ff885145b9e1c1f71b)
* mpc85xx: add SPI kernel loader for TP-Link TL-WDR4900 v1Matthias Schiffer2022-10-1422-0/+1364
| | | | | | | | | | | Similar to the lzma-loader on our MIPS targets, the spi-loader acts as a second-stage loader that will then load and start the actual kernel. As the TL-WDR4900 uses SPI-NOR and the P1010 family does not have support for memory mapping of this type of flash, this loader needs to contain a basic driver for the FSL ESPI controller. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit a296055b82fbb20457273492069ce9d62009e2a1)
* ramips: fix ZyXEL NWA55AXE model nameDavid Bauer2022-10-141-1/+1
| | | | | | | The model name was missing a letter. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 9c8605dee238cdf52e88b6a1aa64d5b7bf5dd846)
* ramips: add support for ZyXEL NWA50AX / NWA55AXEDavid Bauer2022-10-147-2/+248
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Mediatek MT7621 RAM: 256M DDR3 FLASH: 128M NAND ETH: 1x Gigabit Ethernet WiFi: Mediatek MT7915 (2.4/5GHz 802.11ax 2x2 DBDC) BTN: 1x Reset (NWA50AX only) LED: 1x Multi-Color (NWA50AX only) UART Console ------------ NWA50AX: Available below the rubber cover next to the ethernet port. NWA55AXE: Available on the board when disassembling the device. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. If the currently installed image is started from Slot A, the device will flash OpenWrt to Slot B. OpenWrt will panic upon first boot in this case and the device will return to the ZyXEL firmware upon next boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP ----------------- This installation routine is especially useful in case * unknown device password (NWA55AXE lacks reset button) * bricked device Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to owrt.bin $ atnf owrt.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd10 get-status $ zyxel-bootconfig /dev/mtd10 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd10 set-active-image 0 Copy the OpenWrt ramboot-factory image to the device using scp. Write the factory image to NAND and reboot the device. $ mtd write ramboot-factory.bin firmware $ reboot Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit a0b7fef0ffe4cd9cca39a652a37e4f3ce8f0a681)
* ramips: skip bbt scan on mt7621Felix Fietkau2022-10-101-1/+1
| | | | | | | reduces unnecessary flash reads and speeds up boot time Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 55e8d52157f191bf578cf716983764e64c6f94e4)
* ramips: enable support for mtk_bmt in the nand flash driverFelix Fietkau2022-10-101-0/+5
| | | | | Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 4947623d6c801365a60f383217c187e3d9dae953)
* ramips: mt7621_nand: initialize ECC_FDMADDRFelix Fietkau2022-10-101-0/+4
| | | | | | | This is needed for the ECC controller to access FDM data Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 73b2a4ca033bbd84d3e0373d4fd21c559ddc090b)
* ramips: mt7621_nand: reduce log verbosityStijn Tintel2022-10-101-1/+1
| | | | | | | | | | Avoid flooding the log with the message below by increasing the log level to debug: mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry-picked from commit 89c195925109d2b59f284bfdd23a3d853c67e27b)
* ramips: move mt7621_nand driver to filesStijn Tintel2022-10-102-1356/+1353
| | | | | | | | | | | | The patch was rejected by upstream. The mtk_nand driver should be modified to support the mt7621 flash controller instead. As there is no newer version to backport, or no upstream version to fix bugs, let's move the driver to the files dir under the ramips target. This makes it easier to make changes to the driver while waiting for mt7621 support to land in mtk_nand. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry-picked from commit 2f2e81a4ea110328c5434054d1412b4d1d8fde81)
* kernel: mtdsplit: support UBI after FIT imagesFelix Fietkau2022-10-101-2/+7
| | | | | | | Change the partition name accordingly. Same behavior as mtdsplit_uimage Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 62fd9f97090d05637a283d594f2d02958fd36a80)
* kernel: mtk_bmt: skip bitflip check if threshold isn't setChuanhong Guo2022-10-101-1/+1
| | | | | | | kernel spi-nand driver leaves this field empty and let mtd set it later. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> (cherry-picked from commit 6fa50e26e7c1221085d8e71cde7e9148c540c752)
* kernel: mtk_bmt: add debugfs file to attempt repair of remapped sectorsFelix Fietkau2022-10-101-1/+26
| | | | | | | This can be used for sectors that are not physically damaged Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 2a8a333ee96fb0c8d9875abf9fcd5c412f4b19ae)
* kernel: add support for mediatek NMBM flash mapping supportFelix Fietkau2022-10-104-4/+2361
| | | | | | | | This NAND flash remapping method is used on newer MediaTek devices with NAND flash. Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 06382d1af7b2c5afcde605db436522326fbf5467)
* kernel: mtk_bmt: on error, do not attempt to remap out-of-range blocksFelix Fietkau2022-10-102-15/+24
| | | | | | | Pass errors to caller instead Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit be1f2b4d9d01594c2fd20f37b8e63e7cb7a81572)
* kernel: mtk_bmt: fix block copying on remap with bmt v2Felix Fietkau2022-10-101-6/+6
| | | | | | | Copy from the previously mapped block (in case it was remapped already) Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 7d1e2be1605eda85e1a607a3d3ddefed1b961d3d)
* kernel: mtk_bmt: allow get_mapping_block to return an errorFelix Fietkau2022-10-104-8/+25
| | | | | | | | Used by the mapping implementation to indicate that no backing block is available Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit b4c7f8c5f7a2dab76fe90849e112c6bd8f80ab19)
* kernel: split up mtk_bmt driver codeFelix Fietkau2022-10-105-806/+857
| | | | | | | Keep a separate source file per variant Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 601c7b4adb0f91005a8755bf9575c68ac623cc33)
* ath79: fix model name of Extreme Networks WS-AP3805iTom Herbers2022-10-081-1/+1
| | | | | | | | Everywhere else the device is referred to as WS-AP3805i, only the model name wrongly only said AP3805i. Signed-off-by: Tom Herbers <mail@tomherbers.de> (cherry picked from commit 7d6032f310058d7e9b96d7e1dc4d49c8232beff7)
* ath79: add low_mem to tiny imageNick Hainke2022-10-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Devices with SMALL_FLASH enabled have "SQUASHFS_BLOCK_SIZE=1024" in their config. This significantly increases the cache memory required by squashfs [0]. This commit enables low_mem leading to a much better performance because the SQUASHFS_BLOCK_SIZE is reduced to 256. Example Nanostation M5 (XM): The image size increases by 128 KiB. However, the memory statisitcs look much better: Default tiny build: ------ MemTotal: 26020 kB MemFree: 5648 kB MemAvailable: 6112 kB Buffers: 0 kB Cached: 3044 kB low_mem enabled: ----- MemTotal: 26976 kB MemFree: 6748 kB MemAvailable: 11504 kB Buffers: 0 kB Cached: 7204 kB [0] - https://github.com/freifunk-gluon/gluon/commit/7e8af99cf504ca1dc389f282a0c94f4a911571be Signed-off-by: Nick Hainke <vincent@systemli.org> (cherry picked from commit f54ac98f8cec676761e5144ae06640b8007b4b04)
* ath79: move ubnt-xm to tinyNick Hainke2022-10-0511-265/+281
| | | | | | | | | | | | | | ath79 has was bumped to 5.10. With this, as with every kernel change, the kernel has become larger. However, although the kernel gets bigger, there are still enough flash resources. But the RAM reaches its capacity limits. The tiny image comes with fewer kernel flags enabled and fewer daemons. Improves: 15aa53d7ee65 ("ath79: switch to Kernel 5.10") Tested-by: Robert Foss <me@robertfoss.se> Signed-off-by: Nick Hainke <vincent@systemli.org> (cherry picked from commit f4415f7635164ec07ddc22f56df93555804b5767)
* kernel: fix possible mtd NULL pointer dereferenceRafał Miłecki2022-10-044-3/+33
| | | | | | Fixes: cae4d089bc1d3 ("kernel: backport mtd dynamic partition patch") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit a5265497a4f6da158e95d6a450cb2cb6dc085cab)
* kernel: bump 5.10 to 5.10.146John Audia2022-10-047-19/+19
| | | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit eed0a31b90e4feeb65f3b54853bd4db1f5bcd524)
* kernel: bump 5.10 to 5.10.145John Audia2022-10-047-50/+8
| | | | | | | | | | | | | | | Manually rebased: hack-5.10/780-usb-net-MeigLink_modem_support.patch Removed upstreamed: patches-5.10/110-gpio-mpc8xxx-Fix-support-for-IRQ_TYPE_LEVEL_LOW-flow.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.145&id=24196210b198e8e39296e277bb93b362aa207775 Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 8fe67fae1d619467b2b3300178d4309f17cfdb54)
* kernel: bump 5.10 to 5.10.144John Audia2022-10-041-1/+1
| | | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit eff4f8b2f0a2900c945c21c8183d1faa0ac35ec1)
* ramips: fix switch setup for ASUS RT-AX53UMatthias Schiffer2022-10-032-5/+1
| | | | | | | | The device has only 1 WAN + 3 LAN ports. Remove "lan4" interface corresponding to the non-existing port. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit 149fc3a269b435483b31df03d6fd9679286cf9e7)
* ramips: enable LZMA loader to fix Linksys RE6500 bootMark King2022-10-031-0/+1
| | | | | | | | | | | | At some point after 21.02.3 and before 22.03.0, the size limits of the Linksys RE6500 were reached and prevent booting from the 22.03.0 release or builds of current SNAPSHOT. This patch allows builds of master to boot again and has been tested on my device. Fixes: #8577 Signed-off-by: Mark King <mark@vemek.co> (cherry picked from commit bf5b1a53d4ff3f1d742f9ece1ab16555280417ec)
* bcm53xx: backport clk driver fix for DT nodes namesRafał Miłecki2022-10-032-62/+72
| | | | | | | It allows dropping downstream patch renaming DT nodes. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 77d9cce604d32005ddb90e91c6cc9b9cf35068d7)
* ath79: fix LibreRouter-v1 watchdog and poe_passSantiago Piccinini2022-10-021-0/+4
| | | | | | | Watchdog and poe_passthrough gpios require the jtag disabled. Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net> (cherry picked from commit 2ad949b11dbaa4c634868d55a4452d5a558776bd)
* build: fix issues with targets installed via feedsFelix Fietkau2022-09-271-1/+1
| | | | | | | | - fix including modules.mk when a target is being replaced - fix calling make targets from target/linux Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry-picked from commit 3a8825ad6acbf18b2b472ace56be58868af78be7)
* mpc85xx: add patch to fix gpio mpc8xxxJosef Schlehofer2022-09-241-0/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Backports Linux kernel patch [1] for kernel 5.10 where it applies cleanly. This was tested on CZ.NIC Turris 1.1 router running OpenWrt 22.03 release. Before: - In /var/log/messages: ``` [ 16.392988] lm90 0-004c: cannot request IRQ 48 [ 16.398280] lm90: probe of 0-004c failed with error -22 ``` - Sensors does not work: ``` root@turris:~# sensors No sensors found! Make sure you loaded all the kernel drivers you need. Try sensors-detect to find out which these are. ``` After: ``` root@turris:/# sensors sa56004-i2c-0-4c Adapter: MPC adapter (i2c@3000) temp1: +44.0°C (low = +0.0°C, high = +70.0°C) (crit = +85.0°C, hyst = +75.0°C) temp2: +73.8°C (low = +0.0°C, high = +70.0°C) ALARM (HIGH) (crit = +85.0°C, hyst = +75.0°C) ``` [1] https://lore.kernel.org/linux-gpio/20220906105431.30911-1-pali@kernel.org/ Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (cherry picked from commit 2f496c34b6dfbedbfbff8d2ade5d629f096e40bd) (c&p commit ID from openwrt's master) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm4908: fix -EPROBE_DEFER support in bcm4908_enetRafał Miłecki2022-09-212-1/+58
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 1722e23ffcf9038114142a2129c29eb3cdec8ff9)
* kernel: update U-Boot NVMEM driverRafał Miłecki2022-09-213-0/+59
| | | | | | | | 1. Fix casting 2. Support DT-defined variables Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 5652f378c6c607f99a15e6472cdca46c9c4b6162)
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 05:31:45 +0000