aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* kernel: add missing symbol to 5.10 configStijn Tintel2022-12-141-0/+1
| | | | | | | | | | Kernel 5.10.158 added a prompt for the FUNCTION_ERROR_INJECTION symbol. This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing those builds to fail due to a missing symbol. Add the symbol to fix this. Fixes: 6801c460b6a7 ("kernel: bump 5.10 to 5.10.158") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add missing symbol to 5.15 configStijn Tintel2022-12-141-0/+1
| | | | | | | | | | Kernel 5.15.82 added a prompt for the FUNCTION_ERROR_INJECTION symbol. This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing those builds to fail due to a missing symbol. Add the symbol to fix this. Fixes: 68426e54eda4 ("kernel: bump 5.15 to 5.15.82") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* qoriq: switch to kernel 5.15Stijn Tintel2022-12-141-2/+1
| | | | | | | | | The testing kernel has been running fine for months on a rather complex network setup, with one exception being a crash in __xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so let's switch the qoriq target to kernel 5.15 by default. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ipq806x: 5.15: standardize wpq864 partition tableChristian Marangi2022-12-141-43/+43
| | | | | | | | | | Compex WPQ864 contains a non standard partition table. Each partition node should be named partition and should contain a valid reg. Fix an extra "-" present after the reg for SBL2_1 partition. Also add "0:" to each qcom default partition following smem naming. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq806x: 5.15: fix wrong boot-partitions values for split partitionsChristian Marangi2022-12-143-3/+3
| | | | | | | | | | | | | The refreshed patch actually use the format of <start size start size> instead of <start end start end>. This cause boot fail since the rootfs can't be mounted with these wrong values. Fix it to the correct format in each affected dts. Fixes: #11498 Fixes: 6134ba4a34db ("ipq806x: 5.15: add boot-partitions binding to fix block warning") Tested-by: Matt Buczko <mbuczko@hotmail.com> # Askey RT4230W Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ath79: add support for TP-Link CPE605-v1Andrew Cameron2022-12-134-0/+45
| | | | | | | | | | | | | | | | | | | | | | | | TP-Link CPE605-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on Atheros AR9344 Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 1x 10/100 Mbps Ethernet - 64 MB of DDR2 RAM - 8 MB of SPI-NOR Flash - 23dBi high-gain directional antenna and a dedicated metal reflector - Power, LAN, WLAN5G green LEDs - 3x green RSSI LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Signed-off-by: Andrew Cameron <apcameron@softhome.net>
* ramips: add support for Etisalat S3Mikhail Zhilkin2022-12-135-3/+265
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Etisalat S3 is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB Flash: 128 MiB Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7615E): a/n/ac, 4x4 Ethernet: 5x GbE (WAN, LAN1, LAN2, LAN3, LAN4) USB ports: 1x USB3.0 Button: 2 buttons (Reset & WPS) LEDs: - 1x Status (RGB) - 1x 2.4G (blue, hardware, mt76-phy0) - 1x 5G (blue, hardware, mt76-phy1) Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Login to the router web interface under admin account 2. Navigate to Settings -> Configuration -> Save to Computer 3. Decode the configuration. For example, using cfgtool.py tool (see related section): cfgtool.py -u configurationBackup.cfg 4. Open configurationBackup.xml and find the following line: <PARAMETER name="Password" type="string" value="<your router serial \ is here>" writable="1" encryption="1" password="1"/> 5. Insert the following line after and save: <PARAMETER name="Enable" type="boolean" value="1" writable="1" encryption="0"/> 6. Encode the configuration. For example, using cfgtool.py tool: cfgtool.py -p configurationBackup.xml 7. Upload the changed configuration (configurationBackup_changed.cfg) to the router 8. Login to the router web interface (SuperUser:ETxxxxxxxxxx, where ETxxxxxxxxxx is the serial number from the backplate label) 9. Navigate to Settings -> WAN -> Add static IP interface (e.g. 10.0.0.1/255.255.255.0) 10. Navigate to Settings -> Remote cotrol -> Add SSH, port 22, 10.0.0.0/255.255.255.0 and interface created before 11. Change IP of your client to 10.0.0.2/255.255.255.0 and connect the ethernet cable to the WAN port of the router 12. Connect to the router using SSH shell under SuperUser account 13. Run in SSH shell: sh 14. Make a mtd backup (optional, see related section) 15. Change bootflag to Sercomm1 and reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 reboot 16. Login to the router web interface under admin account 17. Remove dots from the OpenWrt factory image filename 18. Update firmware via web using OpenWrt factory image Revert to stock --------------- Change bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 mtd backup ---------- 1. Set up a tftp server (e.g. tftpd64 for windows) 2. Connect to a router using SSH shell and run the following commands: cd /tmp for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \ tftp -l mtd$i -p 10.0.0.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done tftp -l mtd.md5 -p 10.0.0.2 Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery MAC Addresses ------------- +-----+------------+---------+ | use | address | example | +-----+------------+---------+ | LAN | label | *:50 | | WAN | label + 11 | *:5b | | 2g | label + 2 | *:52 | | 5g | label + 3 | *:53 | +-----+------------+---------+ The label MAC address was found in Factory 0x21000 cfgtool.py ---------- A tool for decoding and encoding Sercomm configs. Link: https://github.com/r3d5ky/sercomm_cfg_unpacker Co-authored-by: Karim Dehouche <karimdplay@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* generic: move pending 870 ca8210 fix crash patch to backportChristian Marangi2022-12-132-0/+0
| | | | | | | Patch got merged upstream in kernel 6.1. Move it to backport to better track it. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* generic: fix wrong PTR_ERR use in of net mac address ascii patchChristian Marangi2022-12-132-4/+4
| | | | | | | | | | | | | | | | | | | | nvmem_cell_read return a pointer error when an error occurs. Currently we convert the pointer error to an int while the rest of the function return a void* and expcet an error pointer. Fix this PTR_ERR msuse fixing compilation warning. Fixes the following compilation warning: net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address': net/ethernet/eth.c:547:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion] 547 | return PTR_ERR(mac); | ^~~~~~~~~~~~ net/ethernet/eth.c: In function 'nvmem_cell_get_mac_address_ascii': net/ethernet/eth.c:564:24: warning: returning 'long int' from a function with return type 'void *' makes pointer from integer without a cast [-Wint-conversion] 564 | return PTR_ERR(mac_ascii); | ^~~~~~~~~~~~~~~~~~ Fixes: 7b863af180da ("kernel: move mac-address-ascii patches to generic") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* gemini: Set proper default networksLinus Walleij2022-12-121-0/+15
| | | | | | | | Some Gemini devices are NAS type devices and need to ask for DHCP IP on eth0. Some has a LAN/WAN setup. Add sensible defaults for all known devices. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* uml: switch to Kernel 5.15Christian Lamparter2022-12-121-2/+1
| | | | | | Switch over from testing version. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: remove MR32's openwrt specific patch for LEDsChristian Lamparter2022-12-121-28/+0
| | | | | | | | The patch managed to sneak into v5.15 whereas it was properly deleted for v5.10. Fixes: 8f6e2bb17886 ("bcm53xx: remove MR32's specific get_leds_dt code") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* sunxi: fix sunxi-ir kconfig and descriptionChukun Pan2022-12-123-2/+15
| | | | | | | | | | | Removed a20 in description, since it only works for a10, a13 and a31. Also refreshed kernel config. Fixes: #10466 Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (moved fixes, refreshed, added CONFIG_DVB_USB=n) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* sunxi: modules: remove useless AddDepends/rtcChukun Pan2022-12-121-4/+2
| | | | | | | | | AddDepends/rtc has been removed in commit 3da7fe6, same here. Fixes: 3da7fe6 ("kernel: remove useless AddDepends/rtc abstraction") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (RTC_SUPPORT - though this is implied by the TARGET_sunxi) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: modules/lib-lz4: add lz4hc_compressTony Butler2022-12-111-0/+1
| | | | | | | | | enable option `CONFIG_CRYPTO_LZ4HC` to match default kernel config this only adds the `lz4hc_compress` module, and has no effect on the `lz4_decompress` module which already supports any flavor Signed-off-by: Tony Butler <spudz76@gmail.com>
* lantiq: vr9: include usb driver for fritz 7430Tony Butler2022-12-111-1/+2
| | | | | | | | | | Reported by user: missing driver for USB; add to image definition https://github.com/openwrt/openwrt/issues/11326 Resolves: #11326 Signed-off-by: Tony Butler <spudz76@gmail.com> Acked-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* kernel: Refresh kernel 5.10Hauke Mehrtens2022-12-111-4/+4
| | | | | | | Make the patches apply cleanly again. Fixes: 8327e0fb72f0 ("kernel: backport the dev_set_threaded export to 5.10") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: fix usb driver not loaded for GL-A1300Weiping Yang2022-12-111-0/+8
| | | | | | | This patch enables USB support for the GL.iNet GL-A1300 Repair the usb driver startup phase is not loaded Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* kernel: bump 5.10 to 5.10.158John Audia2022-12-115-8/+8
| | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.157John Audia2022-12-1121-89/+56
| | | | | | | | | | | | | | | Manually rebased: backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch hack-5.10/645-netfilter-connmark-introduce-set-dscpmark.patch Removed upstreamed: pending-5.10/706-netfilter-nf_flow_table-add-missing-locking.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.157&id=b8e494240e69f91517256adcd6fda62d0671772d Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: add symbol in generic config for 5.10.157John Audia2022-12-111-0/+1
| | | | | | Add CONFIG_INET_TABLE_PERTURB_ORDER=16 to generic config Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.82John Audia2022-12-1116-202/+202
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.81John Audia2022-12-1148-178/+142
| | | | | | | | | | | | | | | | | | | | Manually rebased: backport-5.15/715-v6.0-net-ethernet-mtk_eth_soc-add-the-capability-to-run-m.patch hack-5.15/645-netfilter-connmark-introduce-set-dscpmark.patch[1] Removed upstreamed: pending-5.15/701-netfilter-nf_flow_table-add-missing-locking.patch[2] All other patches automatically rebased 1. Rebase by Kevin 'ldir' Darbyshire-Bryant<ldir@darbyshire-bryant.me.uk> 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.81&id=8db9e60cdfdae5b049e32e82323da8f0f989066a Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-stock Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: add symbol in generic config for 5.15.81John Audia2022-12-111-0/+1
| | | | | | Add CONFIG_INET_TABLE_PERTURB_ORDER=16 to generic config Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: backport the dev_set_threaded export to 5.10Felix Fietkau2022-12-101-0/+24
| | | | | | Fixes mt76 build error Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: backport mtk_wed.h from 5.15 to 5.10Felix Fietkau2022-12-101-0/+209
| | | | | | Fixes mt76 build error Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: fix Teltonika RUT230 v1 MAC assignmentDavid Bauer2022-12-091-2/+2
| | | | | | | | | The MAC-Address setup for the Teltonika RUT230 v1 was swapped for the LAN / WAN ports. Also the Label-MAC was assigned incorrect, as the WiFi MAC is printed on the case as part of the SSID, however only the LAN MAC-Address is designated as a MAC-Address. Signed-off-by: David Bauer <mail@david-bauer.net>
* realtek: update GPIO bindings for DGS-1210-10PJan-Niklas Burfeind2022-12-091-4/+26
| | | | | | | | | | | | | | | | add three missing LEDs - PoE-Max - Link/Act - PoE add two missing buttons - mode - reset The last was dropped in commit 61a3d0075b15 ("realtek: update GPIO bindings in the dts files in dts-5.10") Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
* realtek: d-link: add support for dgs-1210-28mp-fAndreas Böhler2022-12-084-90/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | General hardware info: ---------------------- D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4 combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz, DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable with a total PoE power budget of 370W. Power over Ethernet: -------------------- The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports each. They are controlled by a Nuvoton MCU. In order to enable PoE, the realtek-poe package is required. It is installed by default, but currently it requires the manual editing of /etc/config/poe. Keep in mind that the port number assignment does not match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and 24-17. LEDs and Buttons: ----------------- On stock firmware, the mode button is supposed to switch the LED indicators of all port LEDs between Link Activity and PoE status. The currently selected mode is visualized using the respective LEDs. PoE Max indicates that the maximum PoE budget has been reached. Since there is currently no support for this behavior, these LEDs and the mode button can be used independently. Serial connection: ------------------ The UART for the SoC (115200 8N1) is available via unpopulated standard 0.1" pin header marked J6. Pin1 is marked with arrow and square. Pin 1: Vcc 3.3V Pin 2: Tx Pin 3: Rx Pin 4: Gnd OEM installation from Web Interface: ------------------------------------ 1. Make sure you are booting using OEM in image 2 slot. If not, switch to image2 using the menus System > Firmware Information > Boot from image2 Tools > reboot 2. Upload image in vendor firmware via Tools > Backup / Upgrade Firmware > image1 3. Toogle startup image via System > Firmware Information > Boot from image1 4. Tools > reboot Other installation methods not tested, but since the device shares the board with the DGS-1210-28, the following should work: Boot initramfs image from U-Boot: --------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin` command 5. Boot the image with `bootm` command Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ramips: add support for Wavlink WS-WN572HP3 4GJan-Niklas Burfeind2022-12-073-0/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Wavlink WS-WN572HP3 4G is an 802.11ac dual-band outdoor router with LTE support. Specifications; * Soc: MT7621DAT * RAM: 128MiB * Flash: NOR 16MiB GD-25Q128ESIG3 * Wi-Fi: * MT7613BEN: 5GHz * MT7603EN: 2.4GHz * Ethernet: 2x 1GbE * USB: None - only used internally * LTE Modem: Quectel EC200T-EU * UART: 115200 baud * LEDs: * 7 blue at the front * 1 Power * 2 LAN / WAN * 1 Status * 3 RSSI (annotated 4G) * 1 green at the bottom (4G LED) * Buttons: 1 reset button Installation: * press and hold the reset button while powering on the device * keep it pressed for ten seconds * connect to 192.168.10.1 via webbrowser (chromium/chrome works, at least Firefox 106.0.3 does not) * upload the sysupgrade image, confirm the checksum, wait 2 minutes until the device reboots Revert to stock firmware: * same as installation but use the recovery image for WL-WN572HP3 Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ramips: define loadaddr for all UniFi devicesDavid Bauer2022-12-071-0/+2
| | | | | | | | Define the load-address for the DTB of all Ubiquiti UniFi devices using FIT images. From the GPL code we can assume these boards are affected by the same relocating issue with the vendor bootloader. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: also move &slot0 from dtsi down to board dtsDaniel Golle2022-12-073-10/+20
| | | | | | | | | As the referenced MTD partition is only present in the dts, also move &slot0 down to the dts files. Fixes: 64e9b62829 ("mediatek: remove redundant flash entry from dtsi") Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: remove redundant flash entry from dtsiDaniel Golle2022-12-073-74/+16
| | | | | | | | | | Splitting-off the common parts of Ruijie RG-EW3200GX PRO and reyee AX3200-E5 went wrong because the flash descriptiom was kept also in the dtsi. Remove it there, as flash definition is added by both board dts files. Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: optimize the firmware recipe for Netgear NAND devicesShiji Yang2022-12-061-11/+7
| | | | | | | | | | | | | | 1. Drop useless character '0xff' before fake filesystem header. 2. Reduce useless padding to shrink the size of the sysupgrade image. 3. Do not check the size of sysupgrade image. It does not make sense to check the size of a compressed package. 4. Do not take the size of netgear header into account because it will not be written to Flash. 5. Use the default lzma compression dictionary parameter '-d24' to get better performance. Tested on Netgear R6100 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* ath79: convert Netgear R6100 radio calibration to nvmem-cellsShiji Yang2022-12-062-6/+12
| | | | | | | | use nvmem-cells implementation to avoid copying art calibration data to rootfs. Tested on Netgear R6100 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
* kernel: ca8210: Fix crash by zero initializing dataHauke Mehrtens2022-12-062-0/+60
| | | | | | This fixes crashes at bootup on pistachio. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: add support for reyee AX3200-E5Alex Hansen2022-12-066-255/+416
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This is yet another model of the Ruijie RG-EW3200GX PRO with a slightly different flash layout, install process is the same. Specifications: SoC: MT7622B RAM: 256MB Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR Ethernet: 5x1GbE Switch: MT7531BE WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red) 2Keys: Mesh button + Reset button UART: Marked J19 on board. 3.3v, 115200n1 Power: 12V 2.5A Flash instruction: 1. Serve the initramfs.img using a TFTP server with address 10.10.10.3. 2. Interrupt the uboot startup process via UART. 3. Select "System Load Linux to SDRAM via TFTP" item. 4. (important) Back up firmware(mtd7) partitions with: dd if=/dev/mtd7 of=/tmp/firmware.bin and then download the firmware.bin image via SCP. 5. Flash the OpenWrt sysupgrade firmware. Recovery stock firmware: 1. Transfer the firmware.bin image to the device. 2. Flash the image with: mtd write firmware.bin firmware Signed-off-by: Alex Hansen <mralexh123@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: mt7621: enable lzma-loader for netis WF2881Joonhyuk Song2022-12-061-1/+2
| | | | | | Fixes boot loader LZMA decompression issues (LZMA ERROR 1) Signed-off-by: Joonhyuk Song <thenoface303@gmail.com>
* ramips: mt7621: mikrotik 760igs (hEX S) fix SFPJohn Thomson2022-12-061-0/+1
| | | | | | | | | | | | | This device uses an AR8031/AR8033 chip to convert SoC gmac1 RGMII to 1000base-x or sgmii for the SFP fibre cage. The SFP cage requires phy-mode rgmii-rxid, and without it will not recieve any packets: ethtool -S sfp rx_fcs_errors will increase when packets should be being received, but no other _rx counters will change. Fixes: c77858aa792 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii") Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* mediatek: mt7623: build mt6577_auxadc driver into kernelDaniel Golle2022-12-052-1/+3
| | | | | | | | | Set CONFIG_MT6577_AUXADC=y as otherwise reading temperature of the thermal-zone doesn't work on MT7623 (it does work fine without this driver on MT7622 and MT7986). Fixes: f2ae4e2f8c ("mediatek: clean up platform kernel modules") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: use ARTIFACTS for initramfs-factory of I-O DATA WN-AX1167GRINAGAKI Hiroshi2022-12-051-19/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use ARTIFACTS to generate initramfs-based factory image of I-O DATA WN-AX1167GR instead of redundant recipe which generate on KERNEL_INITRAMFS. Note: WN-AX1167GR has 2x OS images on stock firmware. stock log: flash manufacture id: c2, device id 20 18 MX25L12805D(c2 2018c220) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 10 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config " 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "iNIC_rf" 0x000000060000-0x0000007e0000 : "Kernel" 0x000000800000-0x000000f80000 : "app" 0x000000f90000-0x000000fa0000 : "Key" 0x000000fa0000-0x000000fb0000 : "backup" 0x000000fb0000-0x000001000000 : "storage" 1st image is "Kernel" and 2nd is "app" when booted from 1st image. In OpenWrt, those 2x partitions are combined to "firmware" with undefined (empty) areas (0x7e0000-0x7fffff, 0xf80000-0xf8ffff). The size of an OS image partition is 0x780000 (7680 KiB = 7.5 MiB), so check-size for initramfs-factory image needs to be called with the size. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for HiWiFi HC5611Senis John2022-12-045-0/+44
| | | | | | | | | | | | | | | | | | | | | | | CPU: MediaTek MT7628AN @ 575 MHz Flash: 16 MB RAM: 128 MB Ethernet: 10/100Mbps x 1 Wlan: 300 Mbps USB: USB 2.0 x 1 LED: red/green x 1 Button: reset x 1 1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh 2. Upload the openwrt firmware to the router via SCP 3. Login the router via SSH 4. Run `mtd -r write path_to_firmware.bin firmware` I have tested on my device. - The LED will display RED on power-on, After system start completed, trun GREEN - Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device - USB can working under official u-boot Signed-off-by: Senis John <thank243@gmail.com>
* rockchip: enable watchdog driverKien Truong2022-12-041-1/+2
| | | | | | | | Enable Synopsys DesignWare watchdog driver for rockchip device Tested on NanoPi R2S Signed-off-by: Kien Truong <duckientruong@gmail.com>
* Revert "mvebu: switch default kernel to 5.15"Petr Štetiar2022-12-041-1/+2
| | | | | | | | | | | | | | This reverts commit 5429411f732ba76eced30b5b596ec9c0374d0965 as upstream in commit e5f31552674e ("ethernet: fix PTP_1588_CLOCK dependencies") has changed `PTP_1588_CLOCK` dependency handling in 5.15 kernel. That currently leads to `CONFIG_NET_DSA_MV88E6XXX=m` in images produced by buildbots due to `CONFIG_ALL_KMODS=y` config option being used in those builds, which leads to a broken LAN bridge network on several devices. References: https://lists.infradead.org/pipermail/openwrt-devel/2022-December/039950.html Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7621: enable lzma-loader for ZyXEL WAP6805Bjørn Mork2022-12-031-1/+2
| | | | | | | Fixing "Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover". Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mvebu: switch default kernel to 5.15Stijn Segers2022-12-021-2/+1
| | | | | | | | | | | | | In light of https://github.com/openwrt/openwrt/issues/11077, switch mvebu to 5.15 which has been the testing kernel on this target since April - over half a year. Run-tested on the following subtargets: * cortexa9 (Turris Omnia - 03f41b1eb2f15ab06d5800274be6a67c64e2a629) * cortexa72 (MikroTik RB5009UG+S+IN) Tested-by: Enrico Mioso <mrkiko.rs@gmail.com> [GL-MV1000] Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* realtek: fix dell typoJan-Niklas Burfeind2022-12-011-3/+3
| | | | | | | should be add/delete or abbreviated add/del Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
* realtek: refactor keep vlan tag setup, fix tagged forwardingLuiz Angelo Daros de Luca2022-12-017-23/+109
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The code in dsa.c:rtl83xx_port_enable() was trying to set vlan_port_tag_sts_ctrl while dealing with differences between SoCs. However, not only that register has a different address, the register structure and even the 2-bit value semantic changes for each SoC. The vlan_port_tag_sts_ctrl field was dropped and converted into a vlan_port_keep_incoming_tag_set() function that abstracts the different between SoCs. The macro referencing that register migrated to the SoC specific c file as it will be privately used by each file. All magic numbers were converted into macros using BITMASK and FIELD_PREP. The vlan_port_tag_sts_ctrl debugfs was dropped for now as it is already broken for rtl93xx. The best place for SoC specific code might be in each respective c file and not in if/else clauses. The final result is: rtl838x: set ITAG_STS=TAGGED, same as before rtl839x: set ITAG_STS=TAGGED instead of IGR_P_ITAG_KEEP=0x1, fixing forwarding of tagged packets rtl930x: set EGR_ITAG_STS=TAGGED instead of IGR_P_ITAG=0x1, possibly fixing forwarding of tagged packets rtl931x: set EGR_ITAG_STS=TAGGED instead of OTPID_KEEP=0x1, possibly fixing forwarding of tagged packets Without (EGR_)ITAG_STS=TAGGED, at least for rtl839x, forwarded packets will drop the vlan tag while packets from the CPU will still have the correct tag. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* realtek: Fix rtl930x speed status accessorOlliver Schinagl2022-12-011-3/+3
| | | | | | | | | | | | | | The rtl930x speed status registers require 4 bits to indicate the speed status. As such, we want to divide by 8. To make things consistent with the rest of this code, use a bitshift however. This bug probably won't affect many users yet, as there aren't many rtl930x switches in the wild yet with more then 10 ports, and thus a low-impact bugfix. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> [also fix port field extraction] Signed-off-by: Sander Vanheule <sander@svanheule.net>
* ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6Alexander Couzens2022-11-279-217/+347
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP with a miniPCIe slot for a LTE modem. The wAP R AC is similar to the wAP AC but with the miniPCIe slot. The wAP R AC requires installing a LTE modem. The wAP LTE and wAP LTE6 comes with a LTE modem installed. See https://mikrotik.com/product/wap_r_ac for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - CPU: 4x ARM Cortex A7 - RAM: 128MB - Storage: 16MB NOR flash - Wireless: - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports one with 802.3af/at PoE in - 1x Mini PCI-E port (USB2) Installation: Boot the initramfs image via TFTP, then flash the sysupgrade image using sysupgrade. Details at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-15 12:53:00 +0000