aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.14 to 4.14.86Koen Vandeputte2018-12-1023-83/+72
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 180-usb-xhci-add-support-for-performing-fake-doorbell.patch Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.143Koen Vandeputte2018-12-1015-38/+43
| | | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0063-Improve-__copy_to_user-and-__copy_from_user-performa.patch - 201-extra_optimization.patch New symbol: - CONFIG_HARDEN_BRANCH_PREDICTOR Compile-tested on: ar7, at91, brcm2708, ixp4xx, layerscape, orion Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> [fix brcm2708/950-0149-Update-vfpmodule.c.patch] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 3.18 to 3.18.128Koen Vandeputte2018-12-103-20/+20
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 002-phy_drivers_backport.patch Compile-tested on: adm5120 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* apm821xx: WNDAP620: remove bad semicolon in dts after #includeChristian Lamparter2018-12-091-1/+1
| | | | | | | | | This patch fixes a build warning triggered by a semicolon in the dts after the #include directive. netgear-wndap620.dts:11:33: warning: extra tokens at end of #include directive Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx: move fifo-entry-size property to WNDR4700Christian Lamparter2018-12-092-1/+1
| | | | | | | | | This property (and value) came from Netgear's WNDR4700 stock firmware dts. However, other devices do not set it and the EMAC default is 16, which matches that of the programming notes of the APM82181 spec. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: add DT binding support to the TRX and minor parsersRafał Miłecki2018-12-092-0/+26
| | | | | | It allows specifying those parsers directly in the DT. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: fix firmware compatible string for dir860l-b1Russell Senior2018-12-081-1/+1
| | | | | | | | In commit d70ec3008d4cd0540a9f6c88fb7e786107f1679a, a firmware compatible string of "denx,uimage" was added for the Dlink DIR-860L-B1. Unfortunately, this was the wrong string. It needs "seama" instead. Signed-off-by: Russell Senior <russell@personaltelco.net>
* Add support for TL-WA801ND v4Romain MARIADASSOU2018-12-072-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | This add support for TP-Link TL-WA801ND v4 (same as TL-WA801ND v3) : Specification: - System-On-Chip: Qualcomm Atheros QCA9533 - CPU/Speed: 650 MHz - Flash-Chip: Winbond W25Q32BVSIG - Flash size: 4096 KiB - RAM: 32 MiB - Wireless No1: SoC-integrated: QCA9533 2.4GHz 802.11bgn Flash instructions: 1) To flash the image, rename the file openwrt-ar71xx-generic-tl-wa801nd-v4-squashfs-factory.bin to firmware.bin 2) Connect your device to the LAN port, then upload the firmware through web interface. It will try to download the image and flash it. It can take up to 2-3 minutes to finish. When it reaches 100%, the router will reboot itself. Signed-off-by: Romain MARIADASSOU <roms2000@free.fr>
* ath79: dts: Use PowerCloud CAP324 bicolor status LEDDaniel F. Dickinson2018-12-061-3/+3
| | | | | | | | | PowerCloud Systems CAP324 has a bicolor power LED and OpenWrt DTS files / base files support using both colours to better inform user of state and to better match stock firmware, so use green power to indicate normal operation. Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
* ath79: add support for I-O DATA WN-AG300DGRINAGAKI Hiroshi2018-12-065-2/+245
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AG300DGR is a 2T2R 2.4/5 GHz 11n router, based on Atheros AR1022. WN-AG300DGR does not have an LED to indicates power or system status, I set "router" LED as OpenWrt status LED. There is no eeprom data for 5 GHz wlan in "art" partition. Specification: - Atheros AR1022 - 64 MB of RAM (DDR2) - 8 MB of Flash (SPI-NOR) - 2T2R 2.4/5GHz wifi - 2.4 GHz: SoC internal - 5 GHz: Atheros AR93x2 - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 6x keys (4x buttons, 1x slide switch) - 1x USB 2.0 Type-A - UART through-hole on PCB - Vcc, GND, TX, RX from ethernet port side - 115200n8 Flash instruction using factory image: 1. Connect the computer to the LAN port on WN-AG300DGR 2. Connect power cable to WN-AG300DGR and turn it 3. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 4. Select the OpenWrt factory image and click update ("更新") button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: add support for Winchannel WB2000Chuanhong Guo2018-12-064-2/+235
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WB2000 is a dual-band 11N AP using AR9344. The factory firmware used the original DB120 partition table with a small kernel partition at the end of firmware and the kernel will easily get oversized in the future. Since it has to be flashed using UART I also swapped kernel/rootfs and changed the default load address. Specification: - SoC: Atheros AR9344 - RAM: 128 MB - Flash: 16 MB - Ethernet: 10/100/1000 Mbps (Atheros AR8035) - 2x USB 2.0 - WIFI: AR9344(2G) + AR9382(5G) - RTC: DS1338 Known issue: 5G ath9k led doesn't work due to commit ccab68f. Flash instruction: Set up a TFTP server on your computer and configure static IP. Connect UART (J11 TX/GND/RX) and press any key to enter U-boot shell. 1. Change the default boot command: setenv bootcmd 'bootm 0x9f050000 || bootm 0x9fd50000' saveenv 2. Set your router ipaddr and server ipaddr. e.g.: setenv ipaddr 192.168.1.1 setenv serverip 192.168.1.50 3. Load and flash the firmware: tftp 0x80060000 fw.bin erase 0x9f050000 +$filesize cp.b $fileaddr 0x9f050000 $filesize 4. Reset your router: reset Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [Drop the i2c node unit address. Move the ath9k-leds node out of the spi node, it doesn't belong there. Add the #gpio-cells property to the pci wifi node. All fix dtc compiler warnings] Signed-off-by: Mathias Kresin <dev@kresin.me> merge
* ath79: fix ethernet configurations for I-O DATA ETG3-RINAGAKI Hiroshi2018-12-061-1/+13
| | | | | | | | | | | | This commit fixes several issues in eth0 on ETG3-R, and solve slowdown in NA(P)T speed. - add gmac-config with correct configurations - fix pll-data value And I added ref clock-frequency. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ath79: drop unused mtd splitterMathias Kresin2018-12-061-2/+0
| | | | | | | Neither the seama nor the wrgg splitter are used at the moment. Drop them for now to not bloat the target from the beginning. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: remove duplicate image build variablesMathias Kresin2018-12-066-19/+9
| | | | | | | Remove image build variables which are set to the same value as the default image build recipe. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: fix GL.iNet GL-AR300M sysupgradeMathias Kresin2018-12-065-7/+14
| | | | | | | | | | | The userspace boardname derived from the dts compatible was out of sync with the expected board added to the image metadata. This way a sysupgrade is refused. Sync the userspace boardname and the baordname used in the image metdata to allow a seamless sasupgrade. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add SoC or family compatibleMathias Kresin2018-12-0626-30/+24
| | | | | | | Add missing SoC specific compatibles and/or inherit the family compatibles like "ubnt,xm". Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: add AVM EVA firmware partition compatibleDavid Bauer2018-12-062-0/+2
| | | | | | | | | | This commit adds firmware partition compatible for the AVM FRITZ!Box 4020 and AVM FRITZ!WLAN Repeater 300E. This allows to select the correct mtdsplit parser instead of trying all available ones one by one. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: Define firmware partition format to all boards where applicablePetr Štetiar2018-12-0637-0/+37
| | | | | | | | | | Parsing "firmware" partition (to create kernel + rootfs) was implemented using OpenWrt downstream code enabled by CONFIG_MTD_SPLIT_FIRMWARE. With recent upstream mtd changes we can do it in a more clean way for DTS targets. It just requires adding a proper "compatible" string to the "firmware" partition node. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: fix dtc compiler warningsMathias Kresin2018-12-0611-38/+38
| | | | | | | | | | | | | | | | | The latest dtc compiler considers nodes named i2c or spi as the respective bus: /pinctrl/i2c: incorrect #address-cells for I2C bus /pinctrl/spi: incorrect #address-cells for SPI bus Rename the node to fix the false positives. Fix the spi node unit address for the DWR-512-B and UBNT-ER-e50 to get rid of the following warning: SPI bus unit address format error, expected "n" Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt76x8: select only the matching mt76 driverChen Minqiang2018-12-062-3/+9
| | | | | | | | | | | | | | | | | | | | | Select the matching mt76 driver for the PCI wireless of the following devices: - HiWiFi HC5861B - Mercury MAC1200R v2.0 - Netgear AC1200 R6120 - Buffalo WCR-1166DS - ZyXEL Keenetic Extra II - Wavlink WL-WN575A3 Because every device has selected the corresponding mt76 driver, we can include kmod-mt7603 instead of the mt76 metapackage, which used for the wireless of the mt7628 and mt7688 WiSoC. Signed-off-by: Chen Minqiang <ptpt52@gmail.com> [select kmod-mt7603 as target default package, add wireless driver for WL-WN575A3] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ath79: rename qca9533.dtsi to qca953x.dtsiChuanhong Guo2018-12-068-11/+11
| | | | | | | | | qca9533 is a costdown version of qca9531 which doesn't have USB and PCIE. Rename the misleading dtsi names and fix the SoC type of gl-ar300m. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [apply the changes for the gl-x750 as well] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: disable sdhc for HC5661AChuanhong Guo2018-12-062-5/+0
| | | | | | | | | | | | | Currently OpenWrt doesn't support switching MT7628 into AP mode (which is done by writing some undocumented registers in MTK SDK) Without doing so, enabling SD breaks 4 FE ports and the SD controller doesn't work since SD pins aren't configured correctly. Disable SDHC on HC5661A to recover the 4 FE ports. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [drop the sdhci node completely] Signed-off-by: Mathias Kresin <dev@kresin.me>
* apm821xx, ath79, ipq40xx, ipq806x, lantiq, ramips: base-files: Use generic ↵Petr Štetiar2018-12-066-273/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | diag.sh I wanted to add status LEDs support to my imx6 based board and have found out, that I could use diag.sh script found in ramips platform, which seems to be also shared in a few other platforms: 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh And @chunkeey suggested to me, that I can also add lantiq, ipq806x and apm821xx to the list of platforms which could share this generic diag.sh. I've extended the base diag.sh in a way, that if it detects any of the DTS LED aliases, then it would use the generic DTS set_led_state code. The code in platform's diag.sh has moved to base-files package in this commit: base-files: diag.sh: Make it more generic towards DTS so it could be reused Signed-off-by: Petr Štetiar <ynezz@true.cz> Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
* kernel: add DT binding support to AVM EVA parserDavid Bauer2018-12-061-0/+6
| | | | | | | It allows selecting split-firmware parser directly by specifying image-format in the device-tree. Signed-off-by: David Bauer <mail@david-bauer.net>
* octeon: Evaluate board names in alphabetical orderJonathan Thibault2018-12-061-5/+5
| | | | Signed-off-by: Jonathan Thibault <jonathan@navigue.com>
* ipq806x: dts: Add support for RGMII RX and TX clock delaysRam Chandra Jangir2018-12-061-0/+3
| | | | | | | This change enables support to select phy4 in RGMII mode and enables RGMII TX/RX clock internal delays. Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* kernel: ar83xx: Add support for three GMAC's connectionRam Chandra Jangir2018-12-064-1/+69
| | | | | | | | | | | | | We have IPQ8064 AP161 board which has three GMAC's * RGMII x2 * SGMII x1. The existing ar8327 driver does not have support for three GMAC's connection, hence this change adds support for the same. This has been verified on AP148 and AP161 board. Signed-off-by: xiaofeis <xiaofeis@codeaurora.org> Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* ar71xx: Add usb drivers in Archer C7 v4/v5 imagesDaniel Halmschlager2018-12-051-1/+1
| | | | | | | | | | | | This commit adds the default usb packages - kmod-usb-core - kmod-usb2 - kmod-usb-ledtrig-usbport for Archer C7 v4 and v5. (The C7 v5 configuration is based on the v4, therefore the change for v4 also applies for v5.) Signed-off-by: Daniel Halmschlager <dh@dev.halms.at>
* ipq40xx: fix openmesh sysupgrade with tar content out of orderMarek Lindner2018-12-051-3/+3
| | | | | | | | | | | | The tar extraction depends on the order in which the files are added to the tar file. Since the order is not guaranteed and depends on the host system, the combined mtd write fails with sysupgrade images built on some systems. Fix by changing to tar file order independent mtd write. Fixes: 86e18f6706e1 ("ipq806x: add support for OpenMesh A42") Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: add support for EnGenius EAP1300Steven Lin2018-12-056-7/+261
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm 2. Load image via GUI a. Upgrade EAP1300 to FW v3.5.3.2 In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade. b. Transfer to OpenWrt from EnGenius. In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin. 3. Revert to EnGenius EAP1300 To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration. $ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin Signed-off-by: Steven Lin <steven.lin@senao.com>
* brcm2708-gpu-fw: add fw required for camera moduleStijn Tintel2018-12-051-0/+2
| | | | | | | | To be able to use the camera module, start_x=1 has to be set in config.txt. This will cause the bootloader to load the GPU firmware that contain the extra video codecs. Install these firmware files. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add missing symbolStijn Tintel2018-12-042-0/+2
| | | | Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: fix Netgear EX3700/EX3800 wireless driver selectionMathias Kresin2018-12-041-1/+1
| | | | | | Fix the typo to select kmod-mt76x2. Signed-off-by: Mathias Kresin <dev@kresin.me>
* Revert "kernel: use add_mtd_partitions() helper when using OpenWrt parsers"Rafał Miłecki2018-12-033-12/+20
| | | | | | | | | | | | | | | | | | | This reverts commit 7e88753ace0022bd56f77a7a647894f2936cf17b. Using subpartitions (hierarchical layout) resulted in calling MTD ops of parent partition instead of master device ops. That was expected and should work but testing revealed some bugs. Apparently the way MTD_ERASE_PARTIAL is implemented in the OpenWrt breaks something and using parent partition ops triggers using that code. On SmartRG SR400ac it was resulting in: [ 225.487519] jffs2: Erase at 0x01ac0000 failed immediately: errno -22 on the second boot (for some reason erasing was starting over) and it was breaking flash access in a long term. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for D-Link DWR-118-A1Pawel Dembicki2018-12-036-0/+215
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-118-A1 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 3x 10/100 Mbps Ethernet (3 LAN) - 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN) - 1x internal, non-detachable antenna - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - WIFI 5G LED not working - flash is very slow The status led has been assigned to the dwr-118-a1:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7620: select only the matching mt76 driverChen Minqiang2018-12-032-25/+28
| | | | | | | | | | | | | Because every device has selected the corresponding mt76 driver, we can now disable the mt76 metapackage by default to make sure that other devices (those don't need mt76) avoid selecting unwanted packages. We can find the hardware specifies and determine the dependencies on these sites: https://wikidevi.com/wiki/ https://openwrt.org/toh/hwdata/ Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: mt7620: drop mt76 driver for boards without mt76 wirelessChen Minqiang2018-12-031-4/+4
| | | | | | | These boards don't have a mt76 wireless at all and don't need any of the mt76 family drivers. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: mt7620: disable PCIe if nothing is attachedMathias Kresin2018-12-034-16/+0
| | | | | | | | All boards neither expose the PCIe as Mini-PCIe nor have anything attached to the PCIe Bus. Disable PCIe for those by dropping the node from the dts files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7620: add missing pci wifi nodes to dts filesChen Minqiang2018-12-033-0/+24
| | | | | | | | | These devices has pci wifi but not defined in dts: HC5761 HC5861 TINY-AC Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* kernel: use add_mtd_partitions() helper when using OpenWrt parsersRafał Miłecki2018-12-033-20/+12
| | | | | | | | | | | | | | | | | | | | | | | | This helper uses hierarchical partitions layout following the way upstream parsers work. It's closer to what we should use when mainlining our solutions. It also doesn't require hacky casting of struct mtd_partition to the const. THIS WILL AFFECT KERNEL PRINTING PARTITIONS IN THE LOG Something like: [ 3.930158] 0x0000004e0000-0x000001fb0000 : "rootfs_data" will get replaced by: [ 3.907338] Creating 1 MTD partitions on "rootfs": [ 3.912142] 0x00000031d400-0x000001ded400 : "rootfs_data" It's important to understand that "rootfs_data" in above example is a *subpartition* of the "rootfs" now. To get absolute addresses (e.g. for some debugging purposes) one has to add them to the "rootfs", e.g. [ 3.912548] 0x0000001c2c00-0x000001fb0000 : "rootfs" (0x1c2c00 + 0x31d400 = 0x4e0000) Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport 2 mtd partitioning fixesRafał Miłecki2018-12-0310-20/+133
| | | | | | This improves handling of subpartitions. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ath79: add support for Ubiquiti AirRouterRussell Senior2018-12-034-1/+48
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Indoor low-power router with 2.4 GHz radio CPU: Atheros AR7241 rev 1 RAM: 32 MB Flash: 8 MB NOR SPI Switch: Atheros AR7240 Ports: 1x WAN, 4x LAN 10/100 Ethernet WLAN: Atheros AR9285 (2.4 GHz) USB: 1x USB2 host port Note: Ethernet WAN/LAN port naming is reversed from ar71xx. WAN is eth0; LAN is eth1.1. UART settings: 115200, 8N1 LEDs +-------------------------- | | | | | | | | VCC | x x RX | * x | x x | x x TX | * x GND | * x | | | | +-------------------------- ETHERNET PORTS Installation from Ubiquiti firmware, is as for other ubnt-xm AirOs devices. Signed-off-by: Russell Senior <russell@personaltelco.net>
* ath79: split ubnt outdoor device leds into separate dtsiRussell Senior2018-12-035-31/+39
| | | | | | Move common LED configuration into a separate includible dtsi. Signed-off-by: Russell Senior <russell@personaltelco.net>
* x86: make sysupgrade.tgz reachable againTomasz Maciej Nowak2018-12-031-1/+1
| | | | | | | | | Moving binding mount before check for saved sysupgrade configuration made it unreachable. Fix it by moving binding mount after the check. Fixes: f78b2616 (x86: mount writable bootfs) Reported-by: Lucian Cristian <luci@powerneth.ro> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ramips: merge relocate compile into build recipeMathias Kresin2018-11-302-10/+5
| | | | | | | Compile the loader if the relocate-kernel image recipe is used and get rid of the legacy build code to do so. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: specify "firmware" partition format in JBOOT devicesPawel Dembicki2018-11-305-3/+8
| | | | | | | | | | | | | Specify firmware partition format by compatible string. List of devices: -DWR-116-A1 -DWR-118-A2 -DWR-512-B -DWR-921-C1 -LR-25G001 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kernel: add DT binding support to the jimage parserPawel Dembicki2018-11-301-0/+11
| | | | | | | | It allows specifying jimage parser directly in the DT. Tested on LAVA LR-25G001 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for MTC Wireless Router WR1201Valentín Kivachuk2018-11-305-0/+187
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MTC Wireless Router WR1201 is the OEM name of the board. It is also sold rebranded as STRONG Dual Band Gigabit Router 1200. Specification: - SoC: MediaTek MT7621A (880 MHz) - Flash: 16 MiB - RAM: 128 MiB - Wireless: 2.4Ghz(MT7602EN) and 5Ghz (MT7612EN) - Ethernet speed: 10/100/1000 - Ethernet ports: 4+1 - 1x USB 3.0 - 1x microSD reader - Serial baud rate of Bootloader and factory firmware: 57600 The OEM webinterface writes only as much bytes as listed in the uImage header field to the flash. Also, the OEM webinterface evaluates the name field of uImage header before flashing (the string "WR1201_8_128") To flash via webinterface, is mandatory to use first initramfs.bin and after (from the OpenWrt) the sysupgrade.bin Some notes: - Some microSD will not work: mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising SDIO card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising MMC card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising SDIO card mtk-sd 1e130000.sdhci: card claims to support voltages below defined range mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising MMC card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising SDIO card mtk-sd 1e130000.sdhci: no support for card's volts mmc0: error -22 whilst initialising MMC card Signed-off-by: Valentín Kivachuk <vk18496@gmail.com>
* ramips: specify "firmware" partition formatINAGAKI Hiroshi2018-11-29246-0/+246
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specify firmware partition format by compatible string. formats in ramips: - denx,uimage - tplink,firmware - seama It's unlikely but the firmware splitting might not work any longer for the following boards, due to a custom header: - EX2700: two uImage headers - BR-6478AC-V2: edimax-header - 3G-6200N: edimax-header - 3G-6200NL: edimax-header - BR-6475ND: edimax-header - TEW-638APB-V2: umedia-header - RT-N56U: mkrtn56uimg But it rather looks like the uImage splitter is fine with the extra header. The following dts are not touched, due to lack of a compatible string in the matching firmware splitter submodule: - CONFIG_MTD_SPLIT_JIMAGE_FW DWR-116-A1.dts DWR-118-A2.dts DWR-512-B.dts DWR-921-C1.dts LR-25G001.dts - CONFIG_MTD_SPLIT_TRX_FW WCR-1166DS.dts WSR-1166.dts - CONFIG_MTD_SPLIT_MINOR_FW RBM11G.dts RBM33G.dts - CONFIG_MTD_SPLIT_LZMA_FW AR670W.dts - CONFIG_MTD_SPLIT_WRGG_FW DAP-1522-A1.dts Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: unifiy sysupgrade file extensionsMathias Kresin2018-11-292-8/+7
| | | | | | | Use .bin as file extension where possible. The user doesn't need to that sysupgrade images for NAND boards are tarballs. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 09:55:26 +0000