aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* generic: backport fix for Winbond SPI NANDDaniel Golle2023-08-131-0/+49
| | | | | | | | Avoid using stack allocated memory for DMA operations. Fixes: 156c00dedc ("generic: backport Winbond W25N02KV SPI-NAND support") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit e6f8b699189139f09c3685332310ff870610de5e)
* generic: 5.15: rename patches to match correct versionDaniel Golle2023-08-132-0/+0
| | | | | | | | Rename two patches which were only accepted in Linux 6.2, but were marked as if they were accepted in Linux 6.1. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 42e14d3ed870e56c29bff84ce686839d9bab2034)
* armsr: remove redundant phy-marvell-10g moduleDaniel Golle2023-08-131-11/+0
| | | | | | | | | | | | the Marvell 10G PHY driver is no way specific to ARM SystemReady systems, it frequently occurs on SFP+ copper modules and is useful on many targets. Hence it been added to package/kernel/linux/modules/netdevices and we can remove the now redundant target-specific module. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit c524a76f4c09a4e3fa4572612d336b4ef7ff2fb8)
* mediatek: filogic: mt7988: mark RTC clock as criticalDaniel Golle2023-08-131-1/+8
| | | | | | | | | A dependency of the MT7988 MMC host controller on the SoC's RTC clock being running has been discovered. Mark RTC clock as critical to fix MMC host on MT7988. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 0454691960e16bb93ed01f89352cbb375008aaf5)
* mvebu: mcbin-singleshot: enable hearbeat LED by defaultTomasz Maciej Nowak2023-08-111-0/+22
| | | | | | | | | | This has been a part of modified upstream patch but got lost on major kernel bump to 5.15, so bring it back. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> [Add patch for kernel 6.1 too] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 5e6bab661a1028d583338c5823f6a3b9d6444ce0)
* ath79: move ubnt-xm 64M RAM boards back to genericFelix Baumann2023-08-118-31/+33
| | | | | | | | | | return ubnt_rocket-m and ubnt_powerbridge-m back to ath79-generic They have enough RAM-ressources to not be considered as tiny. This reverts the commit f4415f7635164ec07ddc22f56df93555804b5767 partially Signed-off-by: Felix Baumann <felix.bau@gmx.de> (cherry picked from commit 9e86a96af5ecea6e73fa463d6cfa4408e2b49d35)
* kernel: bump 5.15 to 5.15.125John Audia2023-08-1026-37/+39
| | | | | | | | | | | | | 1. Add new symbols to generic config 2. Bump kernel Changelog: https://lore.kernel.org/stable/2023080818-groin-gradient-a031@gregkh/ All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me> [Refreshed on top of OpenWrt 23.05] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit daed3322d347cae5fa538907b5f1fa5d5cfc08c6)
* kernel: bump 5.15 to 5.15.124John Audia2023-08-1024-38/+42
| | | | | | | | | | | | | | | | Changelog: https://lore.kernel.org/stable/2023080341-curliness-salary-4158@gregkh/ 1. Needed to make a change to to package/kernel/linux/modules/netsupport.mk due to upstream moving vxlan to its own directory[1]. @john-tho suggested using the the 6.1 xvlan FILES to circumvent. 2. All patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.124&id=77396fa9096abdbfbb87d63e73ad44d5621cf103 Signed-off-by: John Audia <therealgraysky@proton.me> [Refreshed on top of OpenWrt 23.05] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 81c1172c3626157ff9a146430cd14e32c9c80a5a)
* realtek: add support for HPE 1920-8g-poe+Pawel Dembicki2023-08-096-108/+154
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware information: --------------------- - RTL8380 SoC - 8 Gigabit RJ45 PoE ports (built-in RTL8218B) - 2 SFP ports (built-in SerDes) - RJ45 RS232 port on front panel - 32 MiB NOR Flash - 128 MiB DDR3 DRAM - PT7A7514 watchdog - PoE chips: Nuvoton M0516LDE + BCM59121 Known issues: --------------------- - PoE LEDs are uncontrolled. (Manual taken from f2f09bc00280) Booting initramfs image: ------------------------ - Prepare a FTP or TFTP server serving the OpenWrt initramfs image and connect the server to a switch port. - Connect to the console port of the device and enter the extended boot menu by typing Ctrl+B when prompted. - Choose the menu option "<3> Enter Ethernet SubMenu". - Set network parameters via the option "<5> Modify Ethernet Parameter". Enter the FTP/TFTP filename as "Load File Name" ("Target File Name" can be left blank, it is not required for booting from RAM). Note that the configuration is saved on flash, so it only needs to be done once. - Select "<1> Download Application Program To SDRAM And Run". Initial installation: --------------------- - Boot an initramfs image as described above, then use sysupgrade to install OpenWrt permanently. After initial installation, the bootloader needs to be configured to load the correct image file - Enter the extended boot menu again and choose "<4> File Control", then select "<2> Set Application File type". - Enter the number of the file "openwrt-kernel.bin" (should be 1), and use the option "<1> +Main" to select it as boot image. - Choose "<0> Exit To Main Menu" and then "<1> Boot System". NOTE: The bootloader on these devices can only boot from the VFS filesystem which normally spans most of the flash. With OpenWrt, only the first part of the firmware partition contains a valid filesystem, the rest is used for rootfs. As the bootloader does not know about this, you must not do any file operations in the bootloader, as this may corrupt the OpenWrt installation (selecting the boot image is an exception, as it only stores a flag in the bootloader data, but doesn't write to the filesystem). Example PoE config file (/etc/config/poe): --------------------- config global option budget '180' config port option enable '1' option id '1' option name 'lan8' option poe_plus '1' option priority '2' config port option enable '1' option id '2' option name 'lan7' option poe_plus '1' option priority '2' config port option enable '1' option id '3' option name 'lan6' option poe_plus '1' option priority '2' config port option enable '1' option id '4' option name 'lan5' option poe_plus '1' option priority '2' config port option enable '1' option id '5' option name 'lan4' option poe_plus '1' option priority '2' config port option enable '1' option id '6' option name 'lan3' option poe_plus '1' option priority '2' config port option enable '1' option id '7' option name 'lan2' option poe_plus '1' option priority '2' config port option enable '1' option id '8' option name 'lan1' option poe_plus '1' option priority '2' Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (cherry picked from commit b370753fc409eb2220af7caed9ffd66beed2d041)
* mediatek: filogic: restore non-const type in pinctrl-mt7988 driverDaniel Golle2023-08-071-17/+17
| | | | | | | | | When building with Linux 5.15 the 'const' type results in warnings. Restore the original non-const type in those cases. Fixes: 36d0aa9c2d ("mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDK") Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 1eb67cb0704a61f49d9be9f88aecbce1d881f8c9)
* mediatek: filogic: update MT7988 device treeDaniel Golle2023-08-072-166/+394
| | | | | | | | | * move ethernet to mt7988a.dtsi * move switch definition to mt7988a.dtsi * add PHY LEDs Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 64b99802a61a477ed23fc1f3426fb19d1bc0c6f3)
* mediatek: filogic: sync pinctrl-mt7988 with MediaTek SDKDaniel Golle2023-08-071-115/+300
| | | | | | | Update pinctrl driver for the MT7988 with driver from mtk-openwrt-feeds. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 36d0aa9c2db0f74614b04a152fb092bcc74afb8e)
* mediatek: filogic: enable driver for MediaTek XS-PHYDaniel Golle2023-08-071-1/+1
| | | | | | | | Enable driver for MediaTek SuperSpeedPlus XS-PHY transceiver for the USB3.1 GEN2 controllers found in the MT7988 SoC. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit dc4aafb30939316a163c2eaede6811d871cace2f)
* mediatek: filogic: fix broken sysupgrade scriptPetr Štetiar2023-08-071-0/+1
| | | | | | | | | Changes introduced in commit 54dc1cde48a4 ("mediatek: filogic: add support for Xiaomi WR30U") missed to end the case item with mandatory `;;` which lead to a broken sysupgrade. Fixes: 54dc1cde48a4 ("mediatek: filogic: add support for Xiaomi WR30U") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mediatek: filogic: add specific layout for WR30UHank Moretti2023-08-075-0/+43
| | | | | | | | | Because this device enable NMBM by default, most users use custom U-Boot with NMBM-Enabled in Chinese forums. This layout is the same as the ubootmod layout but enabling NMBM. Signed-off-by: Hank Moretti <mchank9999@gmail.com>
* mediatek: filogic: add support for Xiaomi WR30UHank Moretti2023-08-077-3/+366
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: ESMT F50L1G41LB 128MB RAM: NT52B128M16JR-FL 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, Mesh Power: DC 12V 1A Flash instructions: 1. Get ssh access Check this link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000ne/153769/22 2. Backup import partitions ``` dev: size erasesize name mtd1: 00100000 00020000 "BL2" mtd2: 00040000 00020000 "Nvram" mtd3: 00040000 00020000 "Bdata" mtd4: 00200000 00020000 "Factory" mtd5: 00200000 00020000 "FIP" mtd8: 02200000 00020000 "ubi" mtd9: 02200000 00020000 "ubi1" mtd12: 00040000 00020000 "KF" ``` Use these commands blow to backup your stock partitions. ``` nanddump -f /tmp/BL2.bin /dev/mtd1 nanddump -f /tmp/Nvram.bin /dev/mtd2 nanddump -f /tmp/Bdata.bin /dev/mtd3 nanddump -f /tmp/Factory.bin /dev/mtd4 nanddump -f /tmp/FIP.bin /dev/mtd5 nanddump -f /tmp/ubi.bin /dev/mtd8 nanddump -f /tmp/KF.bin /dev/mtd12 ``` Then, transfer them to your computer via scp, netcat, tftp or others and keep them in a safe place. 3. Setup Nvram Get the current stock: `cat /proc/cmdline` If you find `firmware=0` or `mtd=ubi`, use these commands: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=1 nvram set flag_last_success=1 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ``` If you find `firmware=1` or `mtd=ubi1`, use these commands: ``` nvram set boot_wait=on nvram set uart_en=1 nvram set flag_boot_rootfs=0 nvram set flag_last_success=0 nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit ``` 4. Flash stock-initramfs-factory.ubi If you find `firmware=0` or `mtd=ubi`: `ubiformat /dev/mtd9 -y -f /tmp/stock-initramfs-factory.ubi` If you find `firmware=1` or `mtd=ubi1`: `ubiformat /dev/mtd8 -y -f /tmp/stock-initramfs-factory.ubi` Then reboot your router, it should boot to the openwrt initramfs system now. 5. Setup uboot-env Now it will be setup automatically in upgrade process, you can skip this step. If your `fw_setenv` did not work, you need run this command: `echo "/dev/mtd1 0x0 0x10000 0x20000" > /etc/fw_env.config` Then setup uboot-env: ``` fw_setenv boot_wait on fw_setenv uart_en 1 fw_setenv flag_boot_rootfs 0 fw_setenv flag_last_success 1 fw_setenv flag_boot_success 1 fw_setenv flag_try_sys1_failed 8 fw_setenv flag_try_sys2_failed 8 fw_setenv mtdparts "nmbm0:1024k(bl2),256k(Nvram),256k(Bdata), 2048k(factory),2048k(fip),256k(crash),256k(crash_log), 34816k(ubi),34816k(ubi1),32768k(overlay),12288k(data),256k(KF)" ``` 6. Flash stock-squashfs-sysupgrade.bin Use shell command: `sysupgrade -n /tmp/stock-squashfs-sysupgrade.bin` Or go to luci web. If you need to change to Openwrt U-Boot layout, do next. If you do not need, please ignore it. Change to OpenWrt U-Boot: 1. Flash ubootmod-initramfs-factory.ubi Check mtd partitions: `cat /proc/mtd` ``` mtd7: 00040000 00020000 "KF" mtd8: 02200000 00020000 "ubi_kernel" mtd9: 04e00000 00020000 "ubi" ``` Run following command: `ubiformat /dev/mtd8 -y -f /tmp/ubootmod-initramfs-factory.ubi` Then reboot your router, it should boot to the openwrt initramfs system now. 2. Check mtd again ``` mtd7: 00040000 00020000 "KF" mtd8: 07000000 00020000 "ubi" ``` Make sure mtd8 is ubi. 3. Install kmod-mtd-rw Run command: `opkg update && opkg install kmod-mtd-rw` Or get it in openwrt server, or build it yourself, then install it manually Then run this command: `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Clean up pstore Run Command: `rm -f /sys/fs/pstore/*` 5. Format ubi and create new ubootenv volume ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB ``` 6. (Optional) Add recovery boot feature. ``` ubimkvol /dev/ubi0 -n 2 -N recovery -s 10MiB ubiupdatevol /dev/ubi0_2 /tmp/ubootmod-initramfs-recovery.itb ``` 7. Flash Openwrt U-Boot ``` mtd write /tmp/ubootmod-preloader.bin BL2 mtd write /tmp/ubootmod-bl31-uboot.fip FIP ``` 6. Flash ubootmod-squashfs-sysupgrade.itb Use shell command: `sysupgrade -n /tmp/ubootmod-squashfs-sysupgrade.itb` Or go to luci web. Now everything is done, Enjoy! Go Back to stock from Openwrt U-Boot: 1. Force flash ubootmod-initramfs-recovery.itb Use shell command: `sysupgrade -F -n /tmp/ubootmod-initramfs-recovery.itb` Or go to luci web. Then it should boot to the openwrt initramfs system now. 2. Format ubi and Nvram ``` ubidetach -p /dev/mtd8; ubiformat /dev/mtd8 -y; ubiattach -p /dev/mtd8 mtd erase Nvram ``` 3. Install kmod-mtd-rw Run command: `opkg update && opkg install kmod-mtd-rw` Or get it in openwrt server, or build it yourself, then install it manually Then run this command: `insmod /lib/modules/$(uname -r)/mtd-rw.ko i_want_a_brick=1` 4. Flash stock U-Boot and ubi ``` mtd write /tmp/BL2.bin BL2 mtd write /tmp/FIP.bin FIP mtd write /tmp/ubi.bin ubi ``` Then reboot your router, waiting it finished rollback in minutes. Go Back to stock from stock layout Openwrt: Just run command: `ubiformat /dev/mtd8 -y -f /tmp/ubi.bin` Then reboot your router, waiting it finished rollback in minutes. Notes: 1. Openwrt U-Boot and ubootmod openwrt did not enable NMBM. Please make your backup safe. Signed-off-by: Hank Moretti <mchank9999@gmail.com>
* mediatek: add support for Acer Predator W6David Bauer2023-08-058-0/+579
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: MediaTek MT7986A RAM: 1GB DDR4 FLASH: 4GB eMMC WiFi: 2x2 2.4 GHz 802.11 b/g/n/ax MT7916 DBDC 4x4 5 GHz 802.11 a/n/ac/ax MT7986 2x2 6 GHz 802.11ax MT7916 DBDC ETH: 4x LAN 1Gbit/s (MT7531) 1x WAN 2.5Gbit/s (GPY211) BTN: RESET, WPS LED: Antenna LEDs (GPIO) Mood-LED (Kinetic KTD2601) - unsupported UART: Header nest to USB port - 3V3 115200 8N1 [BUTTON] GND - RX - TX [USB] Installation ------------ 1. Connect to the device using serial console. 2. Interrupt the Autoboot process when promted by sending '0' twice. 3. Serve the OpenWrt initramfs image using TFTP at 192.168.1.66. Name the image "predator.bin" and conenct the TFTP server to the routers LAN port. 4. Configure U-Boot to allow loading unsigned images from MMC $ setenv bootcmd 'mmc read 0x40000000 0x00004400 0x0010000; fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 0x40000000'; saveenv 5. Transfer the image from U-Boot $ setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 predator.bin; fdt addr $(fdtcontroladdr); fdt rm /signature; bootm 6. Wait for OpenWrt to boot 7. Transfer the OpenWrt sysupgrade image to the router using scp. 8. Install OpenWrt using sysupgrade. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 7e7eb5312d7810084547bb54a4b6867c2da08182)
* kernel: bump 5.15 to 5.15.123John Audia2023-07-3194-569/+212
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Manually rebased: bcm4908/patches-5.15/071-v6.1-0001-net-broadcom-bcm4908_enet-handle-EPROBE_DEFER-when-g.patch bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch[*] bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch Removed upstreamed: backport-5.15/735-v6.5-net-bgmac-postpone-turning-IRQs-off-to-avoid-SoC-han.patch[1] backport-5.15/817-v6.5-01-leds-trigger-netdev-Recheck-NETDEV_LED_MODE_LINKUP-o.patch[2] pending-5.15/143-jffs2-reduce-stack-usage-in-jffs2_build_xattr_subsys.patch[3] pending-5.15/160-workqueue-fix-enum-type-for-gcc-13.patch[4] bcm53xx/patches-5.15/036-v6.5-0003-ARM-dts-BCM5301X-Drop-clock-names-from-the-SPI-node.patch[5] bcm53xx/patches-5.15/036-v6.5-0015-ARM-dts-BCM5301X-fix-duplex-full-full-duplex.patch[6] ipq807x/patches-5.15/0048-v6.1-clk-qcom-reset-Allow-specifying-custom-reset-delay.patch[7] ipq807x/patches-5.15/0049-v6.2-clk-qcom-reset-support-resetting-multiple-bits.patch[8] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=02474292a44205c1eb5a03634ead155a3c9134f4 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=86b93cbfe104e99fd3d25a49748b99fb88101573 3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=79b9ab357b6f5675007f4c02ff8765cbd8dc06a2 4. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=d528faa9e828b9fc46dfb684a2a9fd8c2e860ed8 5. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=5899bc4058e89d5110a23797ff94439c53b77c25 6. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=95afd2c7c7d26087730dc938709e025a303e5499 7. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=40844343a8853a08b049d50c967e2a1e28f0ece6 8. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.123&id=6ad5ded420f5d96f7c65b68135f5787a1c7e58d7 Build system: x86/64 Build-tested: ramips/tplink_archer-a6-v3 Run-tested: ramips/tplink_archer-a6-v3 Co-authored-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Audia <therealgraysky@proton.me> [rebased ipq40xx/patches-5.15/902-dts-ipq4019-ap-dk04.1.patch ] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 8590531048f138ff719c8b317c443a6a7538a762) [Refreshed on top of openwrt-23.05] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* bcm53xx: backport more DT changes queued for v6.6Rafał Miłecki2023-07-298-28/+290
| | | | | | | Those sort out BCM53573 Ethernet info finally. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit ca8868a51127f6081a524d47eab937b90af0bf05)
* bcm53xx: add BCM53573 Ethernet fix sent upstream for v6.6Rafał Miłecki2023-07-291-0/+28
| | | | | | | | | | | | | | It seems that DSA-based b53 driver never worked with BCM53573 SoCs and BCM53125. In case of swconfig-based b53 this fixes a regression. Switching bgmac from using mdiobus_register() to of_mdiobus_register() resulted in MDIO device (BCM53125) having of_node set (see of_mdiobus_register_phy()). That made downstream b53 driver read invalid data from DT and broke Ethernet support. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 79fd3e62b4910731c13692b2daa2083e0f95c023)
* ipq4019: fix support for AVM FRITZ!Repeater 3000Alexander Friese2023-07-271-0/+3
| | | | | | | | | new versions of the device have NAND with 8bit ECC which was not yet supported before. This change removes ECC restrictions. Signed-off-by: Alexander Friese <af944580@googlemail.com> (cherry picked from commit 6b11f0ec83ceb9747dcbb0ffca0882b90da46b59)
* ipq40xx: add support for Teltonika RUTX50David Bauer2023-07-265-2/+203
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M Flash: 16MB SPI-NOR (W25Q128) 128MB SPI-NAND (XTX) WiFi: 2T2R (2GHz 802.11n ; 5 GHz 802.11ac) ETH: 4x LAN ; 1x WAN (Gigabit) CELL: Quectel RG501Q 3G/4G/5G UART: Available on the goldfinger connector (Pinout silkscreened) 115200 8N1 3V3 - Only connect RX / TX / GND Installation ------------ 1. Enable SSH in the Teltonika UI (System --> Administration --> Access Control) 2. Check from which partition set the device is currently running from. $ cat /proc/boot_info/rootfs/primaryboot In case this output reads 0, install a Software update from Teltonika first. After upgrade completion, check this file now reads 1 before continuing. 2. Transfer the OpenWrt factory image to the device using scp. Use the same password (user root!) as used for the Web-UI. $ scp -O openwrt-factory.bin root@192.168.1.1:/tmp 3. Connect to the device using ssh as the root user. 4. Install OpenWrt by writing the factory image to flash. $ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin 5. Instruct the bootloaer to boot from the first partition set. $ echo 0 > /proc/boot_info/rootfs/primaryboot $ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin $ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin $ mtd write /tmp/bootconfig.bin /dev/mtd2 $ mtd write /tmp/bootconfig1.bin /dev/mtd3 6. Reboot the device. $ reboot Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 844bb4bfad84cc6267f9b138d1f63b07ed3b77d0)
* ipq40xx: move Teltonika RUT STM32 IO to specific DTSDavid Bauer2023-07-262-37/+37
| | | | | | | Prepare to re-use the DTS for the RUTX50. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit dbc4be142e206e681ac53afa3fd1e4018e7843b7)
* kernel: move NXP DPAA2 SFP patches to generic patchesMathew McBride2023-07-262-2/+2
| | | | | | | | | | | | | These are used by both the armsr (EFI boot) and layerscape targets for phylink-controlled SFP support on NXP DPAA2 platforms (LS1088,LS2088,LX2160). This is in place of commit a7bd96c98f8f ("layerscape: add patches for SFP support on DPAA2 platforms") in the main branch. armsr in main started at kernel 6.1 so there is not an equivalent 5.15 commit to cherry pick. Signed-off-by: Mathew McBride <matt@traverse.com.au>
* layerscape: base-files: remove redundant RAMFS_COPY_* additionsMathew McBride2023-07-261-2/+2
| | | | | | | | All the tools (e.g fw_setenv, ubiupdatevol) and config (fw_env.config) needed for sysupgrade are already included in /lib/upgrade/stage2 Signed-off-by: Mathew McBride <matt@traverse.com.au> (cherry picked from commit 094c37708ace9040e294c5aa7be34bc9e7a8dcc1)
* layerscape: remove Traverse LS1043 boardsMathew McBride2023-07-2610-735/+0
| | | | | | | | | | | | | | | | | The Traverse LS1043 boards were not publicly released, all the production has been going to OEM customers who do not use the image format defined in the OpenWrt tree. Only a few samples were circulated outside Traverse and our OEM customers. The public release (then called Five64) of this series was cancelled in favour of our LS1088A based design (Ten64). It is best to remove these boards to avoid wasting OpenWrt project and contributor resources. Signed-off-by: Mathew McBride <matt@traverse.com.au> (cherry picked from commit 8e7ba6fbae80838c2219ee38307af9c883606c2c)
* layerscape: armv8_64b: add Traverse Ten64 NAND variantMathew McBride2023-07-267-1/+90
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ten64 board[1] is based around NXP's Layerscape LS1088A SoC. It is capable of booting both standard Linux distributions from disk devices, using EFI, and booting OpenWrt from NAND. See the online manual for more information, including the flash layout[2]. This patchset adds support for generating Ten64 images for NAND boot. For disk boot, one can use the EFI support that was recently added to the armvirt target. We previously supported NAND users by building inside our armvirt/EFI target[3], but this approach is not suitable for OpenWrt upstream. Users who used our supplied NAND images will be able to upgrade to this via sysupgrade. Signed-off-by: Mathew McBride <matt@traverse.com.au> [1] - https://www.traverse.com.au/hardware/ten64 [2] - https://ten64doc.traverse.com.au/hardware/flash/ [3] - Example: https://gitlab.com/traversetech/ls1088firmware/openwrt/-/commit/285e4360e1604eb466880d245d48efd9962143a5 (cherry picked from commit af0546da3440dba24217949527e503820350ff05)
* ramips: do not print error log when mdio bus is disabledShiji Yang2023-07-261-1/+1
| | | | | | | | | | The mdio bus is used to control externel switch. In most cases, they are disabled, which is the normal behavior. Treating this as an error makes no sense, so we need to change the notification level from error to info. Fixes: a2acdf960704 ("ramips: mt7620: remove useless GMAC nodes") Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit 285f0668f4058a935389985eb80353c8a5adbc7d)
* ramips: backport upstream mt762x PCIe driver error log fixesShiji Yang2023-07-263-0/+102
| | | | | | | | | | | | | | | | | | | | | These patches silence some mt762x PCIe driver error messeges by removing the useless debugging codes and replacing incorrectly used 'dev_err()' with 'dev_info()': PCI: mt7621: Use dev_info() to log PCIe card detection [1] mips: pci-mt7620: do not print NFTS register value as error log [2] mips: pci-mt7620: use dev_info() to log PCIe device detection result [3] Patch [1] has already been merged into the Linux 6.3 branch. Patches [2] and [3] have been merged into the "mips-next" tree, and they will be part of the upcoming Linux 6.5. [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?h=v6.4-rc7&id=50233e105a0332ec0f3bc83180c416e6b200471e [2] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=9f9a035e6156a57d9da062b26d2a48d031744a1e [3] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=89ec9bbe60b61cc6ae3eddd6d4f43e128f8a88de Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit 4e74777fa8111a2bdf63164a4920a42917faec28)
* lantiq: add patches headersAleksander Jan Bajkowski2023-07-269-32/+129
| | | | | | | | This commit adds headers to the patches, so they can be applied with the git am command. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> (cherry picked from commit 5d51079fd064a86119c6f44920e737cf5e25d3a0)
* kernel: update patches for mediatek filogicFelix Baumann2023-07-261-1/+1
| | | | | | | | Fix complaint from actions Check Kernel patches (mediatek, filogic) https://github.com/openwrt/openwrt/actions/runs/5569719763/job/15081672586?pr=13072 Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* kernel: drop mips highmem offset start overridesFelix Fietkau2023-07-242-38/+0
| | | | | | | | | | | | The maximum offset that can be supported is 0x20000000 Do not override it to to something bigger than that on MT7621, as that could cause issues based on the fixed memory mappings. This makes the last 64 MB RAM unusable on MT7621 devices with 512 MB but avoids incurring a heavy performance hit Fixes: cd2b74e01e8d ("ramips: mt7621: disable highmem support and remove highmem offset patch") Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry picked from commit a110de8152df46a1e2adf7010ba75fb3b1236cd8)
* ramips: mt7621: disable highmem support and remove highmem offset patchFelix Fietkau2023-07-242-3/+19
| | | | | | | | | | | On MT7621 it was observed, that enabling highmem support causes a significant performance drop, as documented in: https://github.com/openwrt/openwrt/issues/13151 By adjusting the highmem start offset, we avoid leaving any RAM unaddressable, even on devices with 512 MB Fixes: https://github.com/openwrt/openwrt/issues/13151 Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry picked from commit cd2b74e01e8d5f5b80b82db1cb204c13ed99dd58)
* mediatek: add support for ZyXEL NWA50AX ProDavid Bauer2023-07-234-1/+257
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Mediatek MT7981 RAM: 512M DDR4 FLASH: 256M NAND ETH: MaxLinear GPY211 (2.5GbE N Base-T) WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax) BTN: 1x Reset LED: 1x Multi-Color UART Console ------------ Available below the rubber cover next to the ethernet port. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. In case this is not the case, OpenWrt will boot only one time, returning to the ZyXEL firmware the second boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP / Recovery ---------------------------- This installation routine is especially useful in case of a bricked device. Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin. $ atnf nwa50axpro-openwrt-initramfs.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd9 get-status $ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd9 set-active-image 0 Copy the OpenWrt sysupgrade image to the device using scp. Write the sysupgrade image to NAND using sysupgrade. $ sysupgrade -n image.bin Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f0445746f6fd96fc7c5394b238153bd2ff22bc5b)
* mediatek: filogic: set DEVICE_DTS_LOADADDR for BPi-R3Daniel Golle2023-07-221-0/+1
| | | | | | | | U-Boot complains that the overlayed DT needs relocation, so set DEVICE_DTS_LOADADDR to have it relocated. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit b1d10e0174f71099016a7e6dcd27b65a77fd51b4)
* octeon: ubnt-edgerouter-4/6p: devicetree cleanupCarsten Spieß2023-07-153-30/+10
| | | | | | | | | | | removed redundant eeprom partition nodes from cn7130_ubnt_edgerouter-4.dts and cn7130_ubnt_edgerouter-6p.dts as they are identically defined in cn7130_ubnt_edgerouter-e300.dtsi. Signed-off-by: Carsten Spieß <mail@carsten-spiess.de> (integrated eeprom referenced node in the .dtsi) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 700f11aaadb7baa38285ed8f928e976a29a72eed)
* octeon: ubnt-edgerouter-e300: fix missing MTD partitionCarsten Spieß2023-07-151-16/+22
| | | | | | | | | | | | | | | The MAC addresses should be read from 3rd MTD partition, but only two MTD partitions are populated. To fix it, a partitions node has to surround the partition nodes in device tree. Tested with Edgerouter 6P Signed-off-by: Carsten Spieß <mail@carsten-spiess.de> (fixed checkpatch complains) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 2b1d7965c7e74e1b31ff29a966eaf6334b0d7057)
* octeon: ubnt-edgerouter-e300: fix LED settingsCarsten Spieß2023-07-151-2/+2
| | | | | | | | | | | | | | LEDs on Edgerouter 6P didn't work correctly: blue /white LED swapped, on/off state inverted Fixed in device tree: swap the GPIO ports for power:blue and power:white LEDs change LED activity from LOW to HIGH Tested on Edgerouter 6P Signed-off-by: Carsten Spieß <mail@carsten-spiess.de> (cherry picked from commit 9009672930f7bda99ec8f6f09a92eb49b6c9aac8)
* armsr: v8: fix NVMEM_IMX_OCOTP_ELE build errorChristian Lamparter2023-07-151-0/+1
| | | | | | | | | | | there's a new symbol NVMEM_IMX_OCOTP_ELE that needs to be defined. otherwise the build will fail: | i.MX On-Chip OTP Controller support (NVMEM_IMX_OCOTP_ELE) [N/m/y/?] (NEW) | make[6]: *** [scripts/kconfig/Makefile:77: syncconfig] Error 1 | make[5]: *** [Makefile:628: syncconfig] Error 2 Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: backport DT changes queued for v6.6Rafał Miłecki2023-07-1410-4/+450
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 37ff916af789911fdefb802ce9903e866eb82435)
* mediatek: replace hack for MaxLinear 2.5G PHYDaniel Golle2023-07-133-166/+63
| | | | | | | Replace hack with proper patch also for Linux 5.15. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 712fa3eff82086da8a13e7e5bc577df17892a581)
* mediatek: dts: mt7988a: remove boottrap hackDaniel Golle2023-07-131-5/+0
| | | | | | | | The PHY driver now uses regmap created from pio syscon, we no longer need the boottrap device. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit f321a49fd523a8d393be8e3cd2de41d67855da91)
* mediatek: use backported Ethernet PHY driver also for 5.15Daniel Golle2023-07-134-1345/+1417
| | | | | | | | Backport in-SoC Gigabit Ethernet PHY driver instead of carrying the driver in files-5.15. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 9fac59009657068d5a58b3d0255d4ca1507dd457)
* mediatek: dts: mt7988a: wire-up mediatek,pio for PHY LEDsDaniel Golle2023-07-132-1/+2
| | | | | | | | | | | The PHY driver needs to read a register containing the values of the bootstrap pins (which happen to be the PHY LEDs) to determine the LED polarities. Allow regmap access to first pinctrl bank by adding the 'syscon' compatible, and reference the pinctrl in the MDIO bus where the PHY driver will look for it. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 1f1e0b1144ebaa4ba8b948a12d989a0a6fc9b76f)
* mediatek: filogic: add H3C Magic NX30 Pro supportChukun Pan2023-07-135-0/+278
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: W25N01GVZEIG 128MB RAM: NT5CB128M16JR-FL 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, WPS Power: DC 12V 1A Flash instructions: 1. PC run command: "telnet 192.168.124.1 99" Username: H3C, password is the web login password of the router. 2. Download preloader.bin and bl31-uboot.fip 3. PC run command: "python3 -m http.server 80" 4. Download files in the telnet window: "wget http://192.168.124.xx/xxx.bin" Replace xx with your PC's IP and the preloader.bin and bl31-uboot.fip. 5. Flushing openwrt's uboot: "mtd write xxx-preloader.bin BL2" "mtd write xxx-bl31-uboot.fip FIP" 6. Connect to the router via the Lan port, set a static ip of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 7. Download initramfs image, reboot router, waiting for tftp recovery to complete. 8. After openwrt boots up, perform sysupgrade. Note: 1. The u-boot-env partition on mtd is empty, OEM stores their env on ubi:u-boot-env. 2. Back up all mtd partitions before flashing. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (cherry picked from commit e78d1a06c8a47be9ea5a306bfb43f3d7ceb89646)
* mediatek: add support for Netgear EX6250v2 seriesWenli Looi2023-07-134-0/+279
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac (Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work currently as there is no driver. Related: https://github.com/openwrt/openwrt/pull/5084 For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2. Specifications: * MT7629, 256 MiB RAM, 16 MiB SPI NOR * MT7761N (2.4GHz) / MT7762N (5GHz) - no driver * Ethernet: 1 port 10/100/1000 * UART: 115200 baud (labeled on board) Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * After installation, perform a factory reset. Wait for the device to boot, then hold the reset button for 10 seconds. This is needed because sysupgrade in the stock firmware will attempt to preserve its configuration using sysupgrade.tgz. See https://github.com/openwrt/openwrt/pull/4182 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> (cherry picked from commit 73de41898fcd06d837b013449c370c493bcdc595)
* image: add additional fields to Netgear encrypted imageWenli Looi2023-07-132-0/+11
| | | | | | | | | | | | | | | | | These fields are used for EAX12 and EX6250v2 series, and perhaps other devices. Compatibility is preserved with the WAX202 and WAX206. In addition, adds the related vars to DEVICE_VARS so that the variables work correctly with multiple devices. References in GPL source: https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz * tools/imgencoder/src/gj_enc.c Contains code that generates the encrypted image. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> (cherry picked from commit 0a1ebccc8702cadc50bc096f1e185472f3927786)
* ath79: DTS improvement for buzzer on RB951G-2HnDPavel Pernička2023-07-121-0/+6
| | | | | | | | | | | Mikrotik RB951 router has a buzzer on the board, which makes annoying noises due to the interference caused by PoE input or Wifi transmission when no GPIO pin state is set. I added buzzer node to device's DTS in order to set deault level to 1 and to provide easier access for it. Signed-off-by: Pavel Pernička <pernicka.pa@gmail.com> (cherry picked from commit dac0a133cf8dbf0bd9afabecdc1092456c451ec7)
* ath79: add support for MikroTik RB951G-2HnDMichał Kępień2023-07-125-0/+70
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MikroTik RB951G-2HnD is a wireless SOHO router that was previously supported by the ar71xx target, see commit 7a709573d7 ("ar71xx: add kernel support for the Mikrotik RB951G board"). Specifications -------------- - SoC: Atheros AR9344 (600 MHz) - RAM: 128 MB (2x 64 MB) - Storage: 128 MB NAND flash (various manufacturers) - Ethernet: Atheros AR8327 switch, 5x 10/100/1000 Mbit/s - 1x PoE in (port 1, 8-30 V input) - Wireless: Atheros AR9340 (802.11b/g/n) - USB: 2.0 (1A) - 8x LED: - 1x power (green, not configurable) - 1x user (green, not configurable) - 5x GE ports (green, not configurable) - 1x wireless (green, not configurable) - 1x button (restart) Unlike on the RB951Ui-2HnD, none of the LEDs on this device seem to be GPIO-controllable, which was also the case for older OpenWRT versions that supported this board via a mach file. The Ethernet port LEDs are controlled by the switch chip. See https://mikrotik.com/product/RB951G-2HnD for more details. Flashing -------- TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedures at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Michał Kępień <openwrt@kempniu.pl> (cherry picked from commit db02cecd6ad2e5962e6e9d8307da34855a083ad6)
* ath79: mikrotik: extract common bits for RB951x-2HnD devicesMichał Kępień2023-07-122-80/+83
| | | | | | | | | Mikrotik RouterBOARD 951Ui-2HnD and Mikrotik RouterBOARD RB951G-2HnD are very similar devices. Extract the DTS bits that are identical for these two boards to a separate DTSI file. Signed-off-by: Michał Kępień <openwrt@kempniu.pl> (cherry picked from commit c6ef4170945c6ab5432382110389f31fea92a76c)
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-12 01:28:46 +0000