aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* realtek: build factory images for all DGS-1210 modelsMarkus Stockhausen2022-07-081-7/+7
| | | | | | | | | Currently we build factory images only for DGS-1210-28 model. Relax that constraint and take care about all models. Tested on DGS-1210-20 and should work on other models too because of common flash layout. Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
* kernel: backport mtd dynamic partition patchChristian Marangi2022-07-0811-9/+221
| | | | | | | | | | | Backport upstream solution that permits to declare nvmem cells with dynamic partition defined by special parser. This provide an OF node for NVMEM and connect it to the defined dynamic partition. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport mtd patch adding of_platform_populate() callsRafał Miłecki2022-07-0812-28/+174
| | | | | | This is required for non-parser drivers handling MTD devices. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* rockchip: reliably distribute net interruptsRonny Kotzschmar2022-07-071-2/+9
| | | | | | | | | On the NanoPI R4S it takes an average of 3..5 seconds for the network devices to appear in '/proc/interrupts'. Wait up to 10 seconds to ensure that the distribution of the interrupts really happens. Signed-off-by: Ronny Kotzschmar <ro.ok@me.com>
* mediatek: mt7622: add missing vbus regulator node to totolink-a8000ru dtsAndrew Sim2022-07-071-0/+10
| | | | | | | | | | On boot, kernel log complains no vbus supply is found: `xhci-mtk 1a0c0000.usb: supply vbus not found, using dummy regulator` so add the dts node entries to solve the issue Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
* kernel: Add missing mediatek configuration optionsHauke Mehrtens2022-07-063-2/+6
| | | | | | | | | | When building the mediatek/mt7629 target in OpenWrt 22.03 the kernel does not have a configuration option for CONFIG_CRYPTO_DEV_MEDIATEK. Add this option to the generic kernel configuration and also add two other configuration options which are removed when we refresh the mt7629 kernel configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* realtek: rename u-boot-env2 to board-nameLuiz Angelo Daros de Luca2022-07-051-1/+1
| | | | | | | | | | | | | | | | | | | | Some realtek boards have two u-boot-env partitions. However, in the DGS-1210 series, the mtdblock2 partition is not a valid u-boot env and simply contains the board/device name, followed by nulls. 00000000 44 47 53 2d 31 32 31 30 2d 32 38 2d 46 31 00 00 |DGS-1210-28-F1..| 00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00040000 00000000 44 47 53 2d 31 32 31 30 2d 35 32 2d 46 31 00 00 |DGS-1210-52-F1..| 00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00040000 The misleading u-boot-env2 name also confuses uboot-envtools. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* realtek: build DGS-1210 images with CAMEO tagMarkus Stockhausen2022-07-052-0/+5
| | | | | | | | From now on we will insert CAMEO tags into sysupgrade images for DGS-1210 devices. This will make the "OS:...FAILED" and "FS:...FAILED" messages go away. Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
* mediatek: mt7622: fix white dome LED of UniFi 6 LRDaniel Golle2022-07-041-3/+1
| | | | | | | | | | The recent differentiation between v1 and v2 of the UniFi 6 LR added support for the v2 version which has GPIO-controlled LEDs instead of using an additional microcontroller to drive an RGB led. The polarity of the white LED, however, was inverted and the default states didn't make a lot of sense after all. Fix that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mvebu: cortexa72: fix ImageBuilder for IEI Puzzle devicesDaniel Golle2022-07-041-2/+0
| | | | | | | | | The line trying to generate the standard sdcard.img.gz fails due to boot.scr not being generated. Remove the line in order to use the default sdcard.img.gz which is exactly the same but includes generating the boot.scr file. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ath79: ag71xx: reuse skbuff_head with napi skb apiSieng Piaw Liew2022-07-041-1/+5
| | | | | | | | | | | | napi_build_skb() reuses NAPI skbuff_head cache in order to save some cycles on freeing/allocating skbuff_heads on every new Rx or completed Tx. Use napi_consume_skb() to feed the cache with skbuff_heads of completed Tx so it's never empty. Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com> [ fixed commit title ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ramips: Add Xiaomi Mi Router 4A 100M InternationalNita Vesa2022-07-033-1/+69
| | | | | | | | | | | | The international version of Mi Router 4A 100M is physically identical to the non-international one, but appears to be using a different partitioning scheme with the "overlay" partition being 2MiB in size instead of 1MiB. This means the following "firmware" partition starts at a different address and the DTS needs to be adjusted for the firmware to work. Signed-off-by: Nita Vesa <werecatf@outlook.com>
* ramips: Add suport for COMFAST CF-WR617ACSergei Iudin2022-07-033-0/+140
| | | | | | | | | | | | | | | | | Specifications: Chipset:MT7628DA+MT7612E Antenna : 2.4Ghz:2x5dbi Antenna + 5.8Ghz:2x5dbi Antenna Wireless Rate:2.4Ghz 300Mbps , 5.8Ghz 867Mbps Output Power :100mW(20dbm) Physical port:110/100Mbps RJ45 WAN Port , 310/100Mbps RJ45 LAN Port Flash: 8Mb DRam: 64Mb Flashing: default bootloader attempts to boot from tftp://192.168.1.10/firmware_auto.bin using 192.168.1.1 Known issues: mac-address-increment for 5GHZ doesnt work, i failed to figure out why. Original firmware using +1 from original value in factory partition. Signed-off-by: Sergei Iudin <tsipa740@gmail.com>
* ramips: add support for Beeline SmartBox GIGAMikhail Zhilkin2022-07-039-3/+349
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Beeline SmartBox GIGA is a wireless WiFi 5 router manufactured by Sercomm company. Device specification -------------------- SoC Type: MediaTek MT7621AT RAM: 256 MiB, Nanya NT5CC128M16JR-EK Flash: 128 MiB, Macronix MX30LF1G18AC Wireless 2.4 GHz (MT7603EN): b/g/n, 2x2 Wireless 5 GHz (MT7613BE): a/n/ac, 2x2 Ethernet: 3 ports - 2xGbE (WAN, LAN1), 1xFE (LAN2) USB ports: 1xUSB3.0 Button: 1 button (Reset/WPS) PCB ID: DBE00B-1.6MM LEDs: 1 RGB LED Power: 12 VDC, 1.5 A Connector type: barrel Bootloader: U-Boot Installation ----------------- 1. Downgrade stock (Beeline) firmware to v.1.0.02; 2. Give factory OpenWrt image a shorter name, e.g. 1001.img; 3. Upload and update the firmware via the original web interface. Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update. Revert to stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3 2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely. MAC Addresses ------------- +-----+-----------+---------+ | use | address | example | +-----+-----------+---------+ | LAN | label | *:16 | | WAN | label + 1 | *:17 | | 2g | label + 4 | *:1a | | 5g | label + 5 | *:1b | +-----+-----------+---------+ The label MAC address was found in Factory 0x21000 Notes ----- 1. The following scripts are required for the build: sercomm-crypto.py - already exists in OpenWrt sercomm-partition-tag.py - already exists in OpenWrt sercomm-payload.py - already exists in OpenWrt sercomm-pid.py - new, the part of this pull request sercomm-kernel-header.py - new, the part of this pull request 2. This device (same as other Sercomm S2,S3-based devices) requires special LZMA and LOADADDR settings for successful boot: LZMA_TEXT_START=0x82800000 KERNEL_LOADADDR=0x81001000 LOADADDR=0x80001000 3. This device (same as several other Sercomm-based devices - Beeline, Netgear, Etisalat, Rostelecom) has partition map (mtd1) containing real partition offsets, which may differ from device to device depending on the number and location of bad blocks on NAND. "fixed-partitions" is used if the partition map is not found or corrupted. This behavour (it's the same as on stock firmware) is provided by MTD_SERCOMM_PARTS module. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* kernel: bump 5.15 to 5.15.50Rui Salvaterra2022-07-036-11/+11
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* realtek: EnGenius EWS2910P: declare and hog the poe-enable GPIOAlexandru Gagniuc2022-07-021-0/+7
| | | | | | | | | | | | GPIO 1 on the RTL8231 is used to force the PoE MCU to disable power outputs. It is not used by any driver, but if accidentally set low, PoE outputs are disabled. This situation is hard to debug, and requires knowledge of the Broadcom PoE protocol used by the MCU. To prevent this situation, hog it as an output high. This is consistent with the ZyXel GS1900 series handles it. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
* mediatek: 5.15: refresh patchesNick Hainke2022-07-012-7/+2
| | | | | | | | Refresh patches: - 510-net-mediatek-add-flow-offload-for-mt7623.patch - 920-dts-mt7622-bpi-r64-fix-wps-button.patch Signed-off-by: Nick Hainke <vincent@systemli.org>
* generic: 5.15: refresh patchesNick Hainke2022-07-013-3/+3
| | | | | | | | | Refresh patches: - 402-mtd-blktrans-call-add-disks-after-mtd-device.patch - 420-mtd-set-rootfs-to-be-root-dev.patch - 495-mtd-core-add-get_mtd_device_by_node.patch Signed-off-by: Nick Hainke <vincent@systemli.org>
* mediatek: mt7622: fix banana pi r64 wps buttonNick Hainke2022-07-011-0/+45
| | | | | | | | | | | | | | | Fix the wps button to prevent wrongly detected recovery procedures. In the official banana pi r64 git the wps button is set to GPIO_ACTIVE_LOW and not GPIO_ACTIVE_HIGH. Import patch to fix on boot unwanted recovery entering: Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level - failsafe button wps was pressed - - failsafe - Signed-off-by: Nick Hainke <vincent@systemli.org>
* ath79: use rtl8366s and rtl8366_smi as a moduleLuiz Angelo Daros de Luca2022-07-012-4/+2
| | | | | | | | | | | | | rtl8366s is used only by dlink_dir-825-b1 and the netgear_wndr family (wndr3700, wndr3700-v2, wndr3800ch, wndr3800.dts, wndrmac-v1, wndrmac-v2). Not tested in real hardware. With rtl8366rb, rtl8366s, rtl8367 as modules, rtl8366_smi can also be a loadable module. This change was tested with tl-wr2543-v1. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* ath79: use rtl8367 as a moduleLuiz Angelo Daros de Luca2022-07-012-2/+1
| | | | | | | rtl8367 is used only by tl-wr2543-v1. Tested both normal and failsafe modes. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* ath79: use rtl8366rb as a moduleLuiz Angelo Daros de Luca2022-07-013-2/+2
| | | | | | | | | | | It looks like rtl8366rb is used only by tplink_tl-wr1043nd-v1 and buffalo_wzr-hp-g300nh-rb. There is no need to have it built-in as it works as a loadable module. Tested both failsafe and normal boot on tl-wr1043nd-v1. buffalo_wzr-hp-g300nh-rb was not tested. Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* ramips: improve YunCore AX820 LEDsThibaut VARÈNE2022-07-011-6/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At least two AX820 hardware variants are known to exist, but they cannot be distinguished (same hardware revision, no specific markings). They appear to have the same LED hardware, but wired differently: - One has a red system LED at GPIO 15, a green wlan2g LED at GPIO 14 and a blue wlan5g LED at GPIO 16; - The other only offers a green system LED at GPIO 15, with GPIO 14 and 16 being apparently not connected Finally, a Yuncore datasheet says the canonical wiring should be: - Blue wlan2g GPIO 14, green system GPIO 15, red wlan5g GPIO 16 All GPIOs are tied to a single RGB LED which is exposed via lightpipe on the device front casing. Considering the above, this patch exposes all three LEDs, preserves the common system LED (GPIO 15) as the openwrt status LED, and removes the color information from the LEDs names since it is not consistent across hardware. The LED naming is made consistent with other YunCore devices. A note is added in DTS to ensure this information is always available and prevent unwanted changes in the future. Fixes: #10131 "YunCore AX820: GPIO LED not correct" Reviewed-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* qoriq: enable Book-E Watchdog TimerStijn Tintel2022-07-012-0/+4
| | | | | | | | | | | | | | | Enable PowerPC Book-E Watchdog Timer support. Having this enabled in-kernel will result in procd starting it during boot. This effectively solves the problem of the WDT in the Winbond W83793 chip potentially resetting the system during sysupgrade, which could result in an unbootable device. While the driver is modular, resulting in procd not starting the WDT during boot (because that happens before kmod load), the WDT handover during sysupgrade results in the WDT being started. This normally shouldn't be a problem, but the W83793 WDT does not like procd's defaults, nor the handover happening during sysupgrade. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* bcm27xx: add support for Raspberry Pi Zero 2Stijn Tintel2022-07-013-6/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Due to licensing uncertainty, we do not include the firmwares for the wireless chips used in the Raspberry Pi Zero 2 W. To have working wireless, follow the instructions below. For people building their own images: mkdir -p files/lib/firmware/brcm wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436-sdio.bin wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436-sdio.txt wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436s-sdio.bin wget -P files/lib/firmware/brcm/ https://github.com/RPi-Distro/firmware-nonfree/raw/bullseye/debian/config/brcm80211/brcm/brcmfmac43436s-sdio.txt Now build the OpenWrt image as usual, and it will include the firmware files in the correct location. For people using ext4 images: Write the ext4 image to the sdcard, then mount the 2nd partition and put the firmware files from the links above in /lib/firmware/brcm relative from the mount point where the partition is mounted. For people using squashfs images: Write the squashfs image to the sdcard, place it in the Raspberry Pi Zero 2 W, boot it and wait for the overlay filesystem to be created. Find the offset of the overlay filesystem in sysfs: # cat /sys/devices/virtual/block/loop0/loop/offset 25755648 Shut down the device, unplug the power and move the SD card to a Linux computer. Mount the 2nd partition of the sdcard as a loop device with the offset found earlier. sudo mount /dev/sdh2 -o loop,offset=25755648 /mnt/temp Put the firmware files from the links above in /upper/lib/firmware/brcm relative to the mount point where the loop device is mounted. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Peter van Dijk <peter@7bits.nl>
* ath79: add support for ASUS RP-AC51Tamas Balogh2022-06-306-6/+165
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RP-AC51 Repeater Category: AC750 300+433 (OEM w. unstable driver) AC1200 300+866 (OpenWrt w. stable driver) Hardware specifications: Board: AP147 SoC: QCA9531 2.4G b/g/n WiFi: QCA9886 5G n/ac DRAM: 128MB DDR2 Flash: gd25q128 16MB SPI-NOR LAN/WAN: AR8229 1x100M Clocks: CPU:650MHz, DDR:600MHz, AHB:200MHz MAC addresses as verified by OEM firmware: use address source Lan/W2G *:C8 art 0x1002 (label) 5G *:CC art 0x5006 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 Start the Asus firmware restoration utility, specify the factory image and press upload Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: set computer to a static ip, 192.168.1.10 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* ath79: add support for ASUS PL-AC56Tamas Balogh2022-06-307-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus PL-AC56 Powerline Range Extender Rev.A1 (in kit with Asus PL-E56P Powerline-slave) Hardware specifications: Board: AP152 SoC: QCA9563 2.4G n 3x3 PLC: QCA7500 WiFi: QCA9882 5G ac 2x2 Switch: QCA8337 3x1000M Flash: 16MB 25L12835F SPI-NOR DRAM SoC: 64MB w9751g6kb-25 DRAM PLC: 128MB w631gg6kb-15 Clocks: CPU:775.000MHz, DDR:650.000MHz, AHB:258.333MHz, Ref:25.000MHz MAC addresses as verified by OEM firmware: use address source Lan/Wan/PLC *:10 art 0x1002 (label) 2G *:10 art 0x1000 5G *:14 art 0x5000 Important notes: the PLC firmware has to be provided and copied manually onto the device! The PLC here has no dedicated flash, thus the firmware file has to be uploaded to the PLC controller at every system start the PLC functionality is managed by the script /etc/init.d/plc_basic, a very basic script based on the the one from Netadair (netadair dot de) Installation: Asus windows recovery tool: have to have the latest Asus firmware flashed before continuing! install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 start the Asus firmware restoration utility, specify the factory image and press upload do NOT power off the device after OpenWrt has booted until the LED flashing TFTP Recovery method: have to have the latest Asus firmware flashed before continuing! set computer to a static ip, 192.168.1.75 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit do NOT power off the device after OpenWrt has booted until the LED flashing Additional notes: the pairing buttons have to have pressed for at least half a second, it doesn't matter on which plc device (master or slave) first it is possible to pair the devices without the button-pairing requirement simply by pressing reset on the slave device. This will default to the firmware settings, which is also how the plc_basic script is setting up the master device, i.e. configuring it to firmware defaults the PL-E56P slave PLC has its dedicated 4MByte SPI, thus it is capable to store all firmware currently available. Note that some other slave devices are not guarantied to have the capacity for the newer ~1MByte firmware blobs! To have a good overlook about the slave device, here are its specs: same QCA7500 PLC controller, same w631gg6kb-15 128MB RAM, 25L3233F 4MB SPI-NOR and an AR8035-A 1000M-Transceiver Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* kernel: bump 5.10 to 5.10.127John Audia2022-06-298-18/+18
| | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* mvebu: add Methode euroDPU supportRobert Marko2022-06-295-4/+35
| | | | | | | | | | | | | | | | Add support for Methode euroDPU which is based on uDPU but does not have a second SFP cage, instead of which a Maxlinear G.hn IC is used. PHY mode is set to 1000Base-X despite Maxlinear IC being capable of 2500Base-X since until 5.15 support for mvebu is available trying to use 2500Base-X will cause buffer overruns for which the fix is not easily backportable. Installation instructions: 1. Boot the FIT initramfs image (openwrt-mvebu-cortexa53-methode_edpu-initramfs.itb) 2. sysupgrade using the openwrt-mvebu-cortexa53-methode_edpu-firmware.tgz Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* mvebu: update and refactor uDPU DTSRobert Marko2022-06-293-34/+211
| | | | | | | | | | | | | | | | | | uDPU DTS has pending upstream fixups, so backport those as well as split the DTS into a DTSI and DTS in preparation for euroDPU support which uses uDPU as the base. Ethernet aliases have not yet been sent upstream but will be soon in order for U-boot to set the correct MAC on both ethernet interfaces instead of just one. Since U-boot environment now has its own partition, update the envtools config script to search for it instead. Patch hardcoding PHY mode is also not applicable anymore, so drop it and set in the uDPU DTS directly. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ath79: add support for RouterBOARD mAPThibaut VARÈNE2022-06-295-0/+134
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik mAP-2nd (sold as mAP) is an indoor 2.4Ghz AP with 802.3af/at PoE input and passive PoE passthrough. See https://mikrotik.com/product/RBmAP2nD for more details. Specifications: - SoC: QCA9533 - RAM: 64MB - Storage: 16MB NOR - Wireless: QCA9533 802.11b/g/n 2x2 - Ethernet: 2x 10/100 ports, 802.3af/at PoE in port 1, 500 mA passive PoE out on port 2 - 7 user-controllable LEDs Note: the device is a tiny AP and does not distinguish between both ethernet ports roles, so they are both assigned to lan. With the current setup, ETH1 is connected to eth1 and ETH2 is connected to eth0 via the embedded switch port 2. Flashing: TFTP boot initramfs image and then perform sysupgrade. The "ETH1" port must be used to upload the TFTP image. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Tested-By: Andrew Powers-Holmes <aholmes@omnom.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ipq40xx: mikrotik: make RouterBoot partition writeableThibaut VARÈNE2022-06-295-5/+0
| | | | | | | | | Linux MTD requires the parent partition be writable for a child partition to be allowed write permission. In order for soft_config to be writeable (and modifiable via sysfs), the parent RouterBoot partition must be writeable Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ath79: mikrotik: add rw soft_config to extra devicesJohn Thomson2022-06-292-2/+0
| | | | | | | Linux MTD requires the parent partition be writable for a child partition to be allowed write permission. Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* kernel: fix variable erasesize patchJohn Thomson2022-06-292-416/+128
| | | | | | | | | Update this pending patch to remove the untested (variable eraseregions) section, alongside simplifying the patch. Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> [refresh and split out unrelated refreshes] Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* kernel: cut broken SPI_NOR 4K eraseblock LIMIT patchJohn Thomson2022-06-299-149/+0
| | | | | | | | | | | | | | | | | | Since 4e0c54bc5bc8 ("kernel: add support for kernel 5.4"), the spi-nor limit 4k erasesize to spi-nor chips below a configured size patch has not functioned as intended. For uniform erasesize SPI-NOR devices, both nor->erase_opcode & mtd->erasesize are used in erase operations. These are set before, and not modified by, this CONFIG_MTD_SPI_NOR_USE_4K_SECTORS_LIMIT patch. Thus, an SPI-NOR device with CONFIG_MTD_SPI_NOR_USE_4K_SECTORS will always use 4k erasesize (where the device supports it). If this patch was fixed to function as intended, there would be cases where devices change from a 4K to a 64K erasesize. Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* x86: 64: Add kmod-igc to default packagesHauke Mehrtens2022-06-291-1/+1
| | | | | | | | This adds the igc driver for the Intel 2.5GBit Ethernet chip to the default packages. Fixes: #10064 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: add support for ASUS RP-AC87Tamas Balogh2022-06-294-0/+200
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RP-AC87 ac2600 Repeater 2.4GHz 800Mbps 5GHz 1733Mbps Hardware specifications: SoC: MT7621A 2 cores 4 threads @880MHz WiFi2G: MT7615E 2G 4x4 b/g/n Wifi5G: MT7615E 5G 4x4 n/ac DRAM: 128MB DDR3 @1200mhz Flash: 16MB MX25L12805D SPI-NOR LAN/WAN: MT7530 1x1000M MAC addresses as verified by OEM firmware: use address source Lan/W5G *:B0 factory 0x8004 (label) W2G *:B4 factory 0x0 Installation: Asus windows recovery tool: install the Asus firmware restoration utility unplug the router, hold the reset button while powering it on release when the power LED flashes slowly specify a static IP on your computer: IP address: 192.168.1.75 Subnet mask 255.255.255.0 Start the Asus firmware restoration utility, specify the factory image and press upload Do not power off the device after OpenWrt has booted until the LED flashing. TFTP Recovery method: set computer to a static ip, 192.168.1.2 connect computer to the LAN 1 port of the router hold the reset button while powering on the router for a few seconds send firmware image using a tftp client; i.e from linux: $ tftp tftp> binary tftp> connect 192.168.1.1 tftp> put factory.bin tftp> quit Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
* qoriq: add kernel 5.15 supportStijn Tintel2022-06-292-0/+403
| | | | | | Add support for kernel 5.15 as testing kernel for qoriq. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* qoriq: enable HARDENED_USERCOPYStijn Tintel2022-06-291-1/+0
| | | | | | | The random crashes observed with HARDENED_USERCOPY enabled no longer seem to occur. Enable HARDENED_USERCOPY to improve security. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* qoriq: disable CONFIG_COMPATStijn Tintel2022-06-291-8/+0
| | | | | | | We do not need support for 32 bit applications, as we're building everything for 64 bit. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* qoriq: 02_network fix sweth globbing logicThibaut VARÈNE2022-06-291-1/+1
| | | | | | This prevents invalid configuration of non-existent sweth devices. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* qoriq: define reset button for Firebox M300Thibaut VARÈNE2022-06-292-1/+13
| | | | | | This patch provides support for the Firebox M300 reset button. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* qoriq: define leds for Firebox M300Thibaut VARÈNE2022-06-292-1/+22
| | | | | | | | This patch provides support for the Firebox M300 only user-controllable bi-color LED, and makes the green "shield" LED act as the typical OpenWrt status led. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* kernel: add missing symbol to 5.15 configStijn Tintel2022-06-291-0/+1
| | | | | | | | Kernel 5.15.49 introduced a new symbol 'LIB_MEMNEQ'. Add it to the generic 5.15 config. Fixes: f1cd14448221 ("kernel: bump 5.15 to 5.15.49") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: add missing symbol to 5.10 configStijn Tintel2022-06-291-0/+1
| | | | | | | | Kernel 5.10.124 introduced a new symbol 'LIB_MEMNEQ'. Add it to the generic 5.10 config. Fixes: 9e5d743422ed ("kernel: bump 5.10 to 5.10.124") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* realtek: add DGS-1210-28 factory imageLuiz Angelo Daros de Luca2022-06-282-1/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | DGS-1210 switches support dual image, with each image composed of a kernel and a rootfs partition. For image1, kernel and rootfs are in sequence. The current OpenWrt image (written using a serial console), uses those partitions together as the firmware partition, ignoring the partition division. The current OEM u-boot fails to validate image1 but it will only trigger firmware recovery if both image1 and image2 fail, and it does not switch the boot image in case one of them fails the check. The OEM factory image is composed of concatenated blocks of data, each one prefixed with a 0x40-byte cameo header. A normal OEM firmware will have two of these blocks (kernel, rootfs). The OEM firmware only checks the header before writing unconditionally the data (except the header) to the correspoding partition. The OpenWrt factory image mimics the OEM image by cutting the kernel+rootfs firmware at the exact size of the OEM kernel partition and packing it as "the kernel partition" and the rest of the kernel and the rootfs as "the rootfs partition". It will only work if written to image1 because image2 has a sysinfo partition between kernel2 and rootfs2, cutting the kernel code in the middle. Steps to install: 1) switch to image2 (containing an OEM image), using web or these CLI commands: - config firmware image_id 2 boot_up - reboot 2) flash the factory_image1.bin to image1. OEM web (v6.30.016) is crashing for any upload (ssh keys, firmware), even applying OEM firmwares. These CLI commands can upload a new firmware to the other image location (not used to boot): - download firmware_fromTFTP <tftpserver> factory_image1.bin - config firmware image_id 1 boot_up - reboot To debrick the device, you'll need serial access. If you want to recover to an OpenWrt, you can replay the serial installation instructions. For returning to the original firmware, press ESC during the boot to trigger the emergency firmware recovery procedure. After that, use D-Link Network Assistant v2.0.2.4 to flash a new firmware. The device documentation does describe that holding RESET for 12s trigger the firmware recovery. However, the latest shipped U-Boot "2011.12.(2.1.5.67086)-Candidate1" from "Aug 24 2021 - 17:33:09" cannot trigger that from a cold boot. In fact, any U-Boot procedure that relies on the RESET button, like reset settings, will only work if started from a running original firmware. That, in practice, cancels the benefit of having two images and a firmware recovery procedure (if you are not consider dual-booting OpenWrt). Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
* ath79: support for TP-Link EAP225 v4Sven Hauer2022-06-283-0/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This model is almost identical to the EAP225 v3. Major difference is the RTL8211FS PHY Chipset. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MIMO * Ethernet (RTL8211FS): 1× 1GbE, 802.3at PoE Flashing instructions: * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J4 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. Signed-off-by: Sven Hauer <sven.hauer+github@uniku.de>
* kernel: backport RTL8211F clkout-disable patchSander Vanheule2022-06-271-0/+119
| | | | | | | | | | | | | | In Linux v5.14 an extra feature was introduced for the RTL8211F phy, allowing to disable a clock output from the phy. Part of that patch is to always (soft) reset the phy upon initialisation. This phy reset is required to have a working ethernet on the TP-Link EAP225-Outdoor v3 and EAP225 v4 after a reboot. Otherwise the ethernet port will only function properly on cold boots. Tested-by: Andre Klärner <kandre@ak-online.be> # EAP225-Outdoor v3 Tested-by: Sven Hauer <sven.hauer+github@uniku.de> # EAP225 v4 Signed-off-by: Sander Vanheule <sander@svanheule.net>
* lantiq: dts: td-w8980: Remove duplicate PCI propertiesMartin Blumenstingl2022-06-271-3/+1
| | | | | | | | | lantiq,bus-clock, interrupt-map-mask and interrupt-map are already defined with these exact values in vr9.dtsi. Drop them from vr9_tplink_tdw8980.dts to just have one place where these are maintained. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* kernel: bump 5.15 to 5.15.49Rui Salvaterra2022-06-2727-229/+168
| | | | | | | | | Deleted (upstreamed): generic/backport-5.15/702-v5.19-34-net-ethernet-mtk_eth_soc-fix-misuse-of-mem-alloc-int.patch [1] [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.49&id=fcba12a4308143f1f1dcb0face8b3ffb51edcc5c Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-23 23:23:07 +0000