aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ath79: add support for Alcatel HH40VAndreas Böhler2023-04-234-0/+191
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Alcatel HH40V is a CAT4 LTE router used by various ISPs. Specifications ============== SoC: QCA9531 650MHz RAM: 128MiB Flash: 32MiB SPI NOR LAN: 1x 10/100MBit WAN: 1x 10/100MBit LTE: MDM9607 USB 2.0 (rndis configuration) WiFi: 802.11n (SoC integrated) MAC address assignment ====================== There are three MAC addresses stored in the flash ROM, the assignment follows stock. The MAC on the label is the WiFi MAC address. Installation (TFTP) =================== 1. Connect serial console 2. Configure static IP to 192.168.1.112 3. Put OpenWrt factory.bin file as firmware-system.bin 4. Press Power + WPS and plug in power 5. Keep buttons pressed until TFTP requests are visible 6. Wait for the system to finish flashing and wait for reboot 7. Bootup will fail as the kernel offset is wrong 8. Run "setenv bootcmd bootm 0x9f150000" 9. Reset board and enjoy OpenWrt Installation (without UART) =========================== Installation without UART is a bit tricky and requires several steps too long for the commit message. Basic steps: 1. Create configure backup 2. Patch backup file to enable SSH 3. Login via SSH and configure the new bootcmd 3. Flash OpenWrt factory.bin image manually (sysupgrade doesn't work) More detailed instructions will be provided on the Wiki page. Tested by: Christian Heuff <christian@heuff.at> Signed-off-by: Andreas Böhler <dev@aboehler.at>
* ath79: use gpios for switch management in WZR-HP-G300NH variantsTony Ambardar2023-04-231-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | The RTL8366S/RB switch node in DTS defines "mii-bus = <&mdio0>" to permit management via SMI but this has likely never worked, instead falling back to using GPIOs in the past: rtl8366s switch: cannot find mdio bus from bus handle (yet) rtl8366s switch: using GPIO pins 19 (SDA) and 20 (SCK) rtl8366s switch: RTL8366 ver. 1 chip found Recently, the rtl8366s and rtl8366_smi drivers were changed from built-in to loadable modules. This affected driver probing order and caused switch initialization (and network access) to fail: rtl8366s switch: using MDIO bus 'ag71xx_mdio' rtl8366s switch: unknown chip id (ffff) rtl8366s switch: chip detection failed, err=-19 Force using GPIOs to manage the switch by dropping the "mii-bus" DTS definition, which works for both built-in and loadable switch drivers. Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module") Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module") Tested-by: Tony Ambardar <itugrok@yahoo.com> # WZR-HP-G300NH (RTL8366S) Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ath79: fix switch support for WZR-HP-G300NH devicesTony Ambardar2023-04-231-1/+2
| | | | | | | | | | | | Switch drivers for RTL8366S/RB were packaged as modules but not properly added to device definitions for WZR-HP-G300NH router variants, breaking network access to both after installation or upgrade. Assign the correct switch driver package for each router. Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module") Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module") Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ramips: fix lzma-loader for buffalo_WSR_600DHPHaoan Li2023-04-231-0/+1
| | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of similar devices. Fixes: #11919 Signed-off-by: Haoan Li <lihaoan1001@163.com>
* bmips: shg2500: add BCM4360 fallback SPROMÁlvaro Fernández Rojas2023-04-232-2/+16
| | | | | | | | Apart from the embedded BCM63268 wireless, this device has an external BCM4360 connected by PCIe which needs a fallback SPROM. b43 isn't enabled for this device because BCM4360 isn't supported (AC PHY). Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: dgnd3700v2: add b43 wireless driverÁlvaro Fernández Rojas2023-04-231-0/+1
| | | | | | | | Apart from the embedded BCM6362 wireless, Netgear DGND3700v2 has external BCM43228 wireless connected by PCIe. Fallback SPROM isn't needed for this one because it has a physical SPROM. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: leds-sercomm-msp430: improve driverÁlvaro Fernández Rojas2023-04-231-3/+7
| | | | | | | - Add missing module functions. - Fix infinite pattern trigger by converting negative values to 0. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: enet: add missing module functionsÁlvaro Fernández Rojas2023-04-232-3/+14
| | | | | | | | | - Add missing MODULE_DEVICE_TABLE(). - Switch bcm6348-iudma to module_platform_driver(). - Add missing MODULE_AUTHOR, MODULE_DESCRIPTION, MODULE_LICENSE and MODULE_ALIAS. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: pci: use standard module functionsÁlvaro Fernández Rojas2023-04-233-24/+21
| | | | | | | late_initcall_sync() is no longer needed so standard module functions can be used on all bmips PCI/PCIe drivers. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: drop custom b43-sprom fixupsÁlvaro Fernández Rojas2023-04-232-1199/+0
| | | | | | b43-sprom fixups and no longer used and can be removed from bmips targets. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: switch to generic bcma/ssb fallback SPROMÁlvaro Fernández Rojas2023-04-2312-64/+12
| | | | | | | | Stop using bmips b43-sprom fixups and switch to generic bcma/ssb fallback SPROMs. This way we don't need to include the b43-sprom fixups on devices without Broadcom wireless. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: add bcma/ssb fallback SPROM supportÁlvaro Fernández Rojas2023-04-236-3/+1841
| | | | | | | This adds generic kernel support for Broadcom Fallback SPROMs so that it can be used in any target, even non Broadcom ones. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* generic: 5.15: replace ramips AR8033 fiber patch with 5.18 patchesDaniel Kestrel2023-04-225-184/+375
| | | | | | | | | | | | A patch was added in kernel 5.4 to support the fiber operation of AR8033 with ramips devices. In kernel 5.18 similar enhancements were added to the kernel. Those patches are required for other fiber based devices but when added, build fails for ramips targets. This commit removes the ramips patch and adds the kernel 5.18 ones. Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de> [ split commit,refresh patch and improve commit message ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* generic: 5.10: replace ramips AR8033 fiber patch with 5.18 patchesDaniel Kestrel2023-04-226-184/+456
| | | | | | | | | | | | A patch was added in kernel 5.4 to support the fiber operation of AR8033 with ramips devices. In kernel 5.18 similar enhancements were added to the kernel. Those patches are required for other fiber based devices but when added, build fails for ramips targets. This commit removes the ramips patch and adds the kernel 5.18 ones. Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de> [ split commit, refresh patch and improve commit title ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* generic: 5.10: replace pending 730-net-phy-at803x-fix... with upstreamChristian Marangi2023-04-2210-32/+34
| | | | | | | | | Replace pending 730-net-phy-at803x-fix-feature-detection.patch with upstream version and move it to backport. Refresh other related patch while moving it. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* kernel: refresh 729-net-phy-realtek-introduce-rtl822x_probe.patchDaniel Golle2023-04-221-7/+7
| | | | | | | The patch needs to be refreshed to apply cleanly. Fixes: 998b973157 ("kernel: net: phy: realtek: improve RealTek 2.5G PHY driver") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for TP-Link TL-XDR4288/608xChukun Pan2023-04-228-4/+543
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7986A 4x A53 Flash: ESMT F50L1G41LB 128MB RAM: ESMT M15T4G16256A 512MB Ethernet (Max Speed): XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan WiFi: XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R) XDR6086/XDR6088: WiFi1: MT7976GN 2.4GHz 4T4R WiFi2: MT7976AN 5GHz 4T4R Button: Reset, WPS, Turbo USB: 1 x USB 3.0 Power: DC 12V 4A Flash instructions: 1. Execute the following operation to open nc shell: https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting 2. Replace the stock bootloader to OpenWrt's: dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip 3. Connect to your PC via the Gigabit port of the router, set a static ip on the ethernet interface of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 4. Download the initramfs image, and restart the router, waiting for tftp recovery to complete. 5. After openwrt boots up, perform sysupgrade. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> [Add uboot build, fit and sysupgrade support, fix RealTek PHYs] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: net: phy: realtek: improve RealTek 2.5G PHY driverDaniel Golle2023-04-228-31/+251
| | | | | | | | | | | | | | | | | | | | * use interface mode switching only when operating in C45 mode Linux prevents switching the interface mode when using C22 MDIO, hence use rate-adapter mode in case the PHY controlled via C22. * use phy_read_paged where appropriate * use existing generic inline functions to handle 10GbE advertisements instead of redundantly defining register macros in realtek.c which are not actually vendor-specific. * make sure 10GbE advertisement is valid, preventing false-positive warning "Downshift occurred from negotiated speed 2.5Gbps to actual speed 1Gbps, check cabling!" with some link-partners using 1G mode. * Support Link Down Power Saving Mode (ALDPS) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.10 to 5.10.178John Audia2023-04-2218-110/+41
| | | | | | | | | | | Removed upstreamed: backport-5.10/430-v6.3-ubi-Fix-failure-attaching-when-vid_hdr-offset-equals.patch[1] 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.178&id=0279e82e148407feec88466990de14bcba9e12c0 All other patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.108John Audia2023-04-2225-195/+41
| | | | | | | | | | | | | | | | | Removed upstreamed: backport-5.15/430-v6.3-ubi-Fix-failure-attaching-when-vid_hdr-offset-equals.patch[1] backport-5.15/612-v6.3-skbuff-Fix-a-race-between-coalescing-and-releasing-S.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.108&id=85d7a7044b759d865d10395a357632af00de5867 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.108&id=906a6689bb0191ad2a44131a3377006aa098af59 Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* generic: update nvmem cell mac-address-ascii supportChukun Pan2023-04-212-42/+52
| | | | | | | | Instead of use mac-address-ascii in nvmem_get_mac_address function, move it into of_get_mac_addr_nvmem function to support more devices. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: MSG1500 X.00: switch to mac-address-ascii dtsChukun Pan2023-04-213-17/+30
| | | | | | | | The Config partition of some machines is special, and the openwrt script cannot read the protest_lan_mac correctly. This problem can be solved by reading the mac address (ascii) in dts. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: remove redundant code for tuf-ax4200Chukun Pan2023-04-211-2/+1
| | | | | | Remove redundant code in 02_network. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: move mac address setting togetherChukun Pan2023-04-211-4/+6
| | | | | | Simultaneously sort in the order of letters. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: fix network config for mt7986a-rfbChukun Pan2023-04-211-1/+3
| | | | | | | Fix the network configuration according to the device tree. Fixes: 5faff99 ("mediatek: filogic: fix mt7986a ethernet devicetree entries") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: filogic: update kernel config-5.15Daniel Golle2023-04-201-1/+4
| | | | | | | Expose thermal-zone as hwmon sensor, remove thermal emulation driver and add some missing symbols. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: bpi-r3: allow up to 3W per SFP moduleDaniel Golle2023-04-201-0/+2
| | | | | | | | | According to SinoVoip up to 3A @ 3.3V are available for both SFP modules together. Raise energy limit from 1W (default) to 3W, however, be aware that using modules consuming more than 1W will require active cooling! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.15 to 5.15.107John Audia2023-04-199-18/+18
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* bmips: pci-bcm6348: load IO resource from DT rangesÁlvaro Fernández Rojas2023-04-183-28/+14
| | | | | | Correctly load IO resource from DT ranges and remove the specific IO resource. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: drop unneeded ath9k fixupÁlvaro Fernández Rojas2023-04-182-243/+1
| | | | | | | We no longer need the custom ath9k fixup now that we're using the standard kmod-owl-loader. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* bmips: hg556a: switch to kmod-owl-loaderÁlvaro Fernández Rojas2023-04-183-14/+66
| | | | | | Stop using custom ath9k fixup and switch to standard kmod-owl-loader Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* ath79: mikrotik: update kernel on NAND using YafutMichał Kępień2023-04-183-8/+5
| | | | | | | | | | | | | | | | | | | | | Instead of erasing the entire NAND partition holding the kernel during every system upgrade and then flashing a Yaffs file system image prepared using kernel2minor (not accounting for bad blocks in the process), use the Yafut utility to replace the kernel executable on MikroTik NAND devices, preserving the existing Yaffs file system (including bad block information) on the partition holding the kernel. Add Yafut to DEFAULT_PACKAGES for the ath79/mikrotik target, so that the tool is included in the initramfs images created when building for multiple profiles. However, exclude Yafut from the images built for MikroTik devices with NOR flash as the tool is currently only meant to be used on devices with NAND flash. As this addresses the concerns for MikroTik NAND devices discussed in commit 9d96b6fb72 ("ath79/mikrotik: disable building NAND images"), re-enable building images for these devices. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* kernel: backport MEMREAD ioctlMichał Kępień2023-04-1815-17/+908
| | | | | | | | | MEMREAD is a new ioctl for MTD character devices that was first included in Linux 6.1. It allows userspace applications to use the Linux kernel's OOB autoplacement mechanism while reading data from NAND devices. The Yafut tool needs this ioctl to do its job. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* ath79: mikrotik: drop unused files from ramdiskMichał Kępień2023-04-181-2/+1
| | | | | | | | | | | | | | | | | | | The ramdisk used by sysupgrade on MikroTik devices currently includes U-Boot fw_* files that are not necessary for performing a system upgrade on that platform. The relevant lines were added to target/linux/ath79/mikrotik/base-files/lib/upgrade/platform.sh by commit a66eee6336 ("ath79: add mikrotik subtarget"), likely because they also existed in target/linux/ath79/nand/base-files/lib/upgrade/platform.sh, where the platform_do_upgrade_mikrotik_nand() function moved by commit a66eee6336 originally lived. However, these lines were added to target/linux/ath79/nand/base-files/lib/upgrade/platform.sh by commit 55e6c903ae ("ath79: GL-AR300M: provide NAND support; increase to 4 MB kernel"), which is not related to MikroTik devices in any way. Remove the code adding unused U-Boot fw_* files to the ramdisk used by sysupgrade on MikroTik devices. Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
* ath79: create Aruba AP-105 APBoot compatible imageDavid Bauer2023-04-181-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Alter the Aruba AP-105 image generation process so OpenWrt can be loaded with the vendor Aruba APBoot. This works by prepending the OpenWrt LZMA loader to the uImage and jumping directly to the loader. Aruba does not offer bootm on these boards. This approach keeps compatibility to devices which had their U-Boot replaced. Both bootloaders can boot the same image. The same modification is most likely also possible for the Aruba AP-175. With this patch, new installations do not require replacing the bootloader and can be performed from the serial console without opening the case. Installation ------------ 1. Attach to the serial console of the AP-105. Interrupt autoboot and change the U-Boot env. $ setenv apb_rb_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; netget 0x84000000 ap105.bin; go 0x84000040" $ setenv apb_fb_openwrt "cp.b 0xbf040000 0x84000000 0x10000; go 0x84000040" $ setenv bootcmd "run apb_fb_openwrt" $ saveenv 2. Load the OpenWrt initramfs image on the device using TFTP. Place the initramfs image as "ap105.bin" in the TFTP server root directory, connect it to the AP and make the server reachable at 192.168.1.66/24. $ run apb_rb_openwrt 3. Once OpenWrt booted, transfer the sysupgrade image to the device using scp and use sysupgrade to install the firmware. Signed-off-by: David Bauer <mail@david-bauer.net>
* ath79: fix LED pinout for Comfast CF-E314N v2Mark Onstid2023-04-171-6/+6
| | | | | | | | | | | | In addition to standardizing LED names to match the rest of the systems, this commit fixes a possibly erroneous pinout for LEDs in Comfast CF-E314N v2. In particular, rssimediumhigh and rssihigh are moved from pins 13 and 14 to 14 and 16 respectively. In addition to working on a test device, this pinout better matches the one set out in the prototype support patch for the device in Github PR #1873. Signed-off-by: Mark Onstid <turretkeeper@mail.com>
* ramips: add Xiaomi RA75 red signal ledOleksandr Zharov2023-04-171-0/+11
| | | | | | | | | | | | | | | | | RA75 has 5 physical LEDs under 2 indicators, mixed with light pipes: Indicator "System": GPIO0: blue GPIO2: amber Indicator "Signal": GPIO44: blue GPIO37: amber GPIO46: red All except GPIO46 were already added by Jo Deisenhofer. GPIO46 is used for UART1 by default, so it needs additional pin control change in devicetree to be operational. Verified on my RA75. Signed-off-by: Oleksandr Zharov <alex.zeed@gmail.com>
* ipq40xx: convert AP-365 to DSADavid Bauer2023-04-152-2/+2
| | | | | | | | | Re-enable the Aruba AP-365 with DSA support. Changes are trvivial, as the board design is pretty much the already updated AP-303. Run-tested on the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: backport fix for recently introduced UBI bugDaniel Golle2023-04-154-4/+142
| | | | | | | | | Import commit "ubi: Fix failure attaching when vid_hdr offset equals to (sub)page size" which did not yet make it to stable upstream Linux trees. Fixes: #12232 Fixes: #12339 Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: backport fix for a page pool related race conditionFelix Fietkau2023-04-142-0/+170
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* generic: move accepted patch to backport-5.15Daniel Golle2023-04-132-13/+37
| | | | | | | | | | The patch adding SFP quirk for MXPD 483II was accepted upstream and will be part of Linux v6.3: https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=ad651d68cee75e9ac20002254c4e5d09ee67a84b Move the patch from pending-5.15 to backport-5.15. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: sync pinctrl-mt7981 and pinctrl-mt7986 driversDaniel Golle2023-04-132-25/+150
| | | | | | | Now that new pinconf features have been backported sync pinctrl-mt7981 and pinctrl-m7986 with bleeding-edge upstream versions. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: backport new pinctrl featuresDaniel Golle2023-04-137-0/+1077
| | | | | | | | Backport new features for MediaTek pinctrl/pinconf drivers from upstream. This will serve as the base to improve pinconf bias/pull-up/pull-down on MT7981 and MT7986, and also prepare for upcoming support for MT7988. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mvebu: puzzle-mcu: add mcu write retry functionIan Chang2023-04-132-0/+126
| | | | | | | Avoid MCU getting "command reply receive timed out" message when LED configuration setting trigger function is enabled in heartbeat mode. Signed-off-by: Ian Chang <ianchang@ieiworld.com>
* base-files: fix Linksys upgrade, restore config stepMichael Trinidad2023-04-112-2/+2
| | | | | | | | | | | | | It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for devices using the linksys.sh script. As a result, configuration was not preserved over sysupgrade steps. This corrects a typo in the call of nand_do_upgrade_failed for ipq40xx and ipq806x devices using the linksys.sh script. Fixes: 8634c1080d50 ("ipq40xx: Fix Linksys upgrade, restore config step") Fixes: 2715aff5df83 ("ipq806x: Fix Linksys upgrade, restore config step") Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
* mvebu: cortexa9: fix Linksys upgrade, restore config stepMichael Trinidad2023-04-111-1/+6
| | | | | | | | | | | | It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for devices using the linksys.sh script. As a result, configuration was not preserved over sysupgrade steps. This restores the preservation of configs for mvebu/cortexa9 devices using the linksys.sh script. Fixes: e25e6d8e5407 ("base-files: fix and clean up nand sysupgrade code") Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
* kirkwood: fix Linksys upgrade, restore config stepMichael Trinidad2023-04-111-1/+6
| | | | | | | | | | | | | | It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for devices using the linksys.sh script. As a result, configuration was not preserved over sysupgrade steps. This restores the preservation of configs for kirkwood devices using the linksys.sh script. Fixes: e25e6d8e5407 ("base-files: fix and clean up nand sysupgrade code") Fixes: #12298 Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
* bcm53xx: switch to Kernel 5.15 by defaultPaul Spooren2023-04-101-2/+1
| | | | | | | Getting ready for the next release. Signed-off-by: Paul Spooren <mail@aparcar.org> Tested-by: Rafał Miłecki <rafal@milecki.pl>
* bcm4908: switch to Kernel 5.15 by defaultPaul Spooren2023-04-101-2/+1
| | | | | | | | Getting ready for the next release. Signed-off-by: Paul Spooren <mail@aparcar.org> [rmilecki: tested on GT-AC5300: boot, sysupgrade & 940 Mbps NAT] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bmips: dts: add missing phy modesÁlvaro Fernández Rojas2023-04-105-0/+17
| | | | | | PHY modes should be defined in the device tree for the bcm63xx internal switch. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 00:20:12 +0000