aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: do not print error log when mdio bus is disabledShiji Yang2023-07-261-1/+1
| | | | | | | | | | The mdio bus is used to control externel switch. In most cases, they are disabled, which is the normal behavior. Treating this as an error makes no sense, so we need to change the notification level from error to info. Fixes: a2acdf960704 ("ramips: mt7620: remove useless GMAC nodes") Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit 285f0668f4058a935389985eb80353c8a5adbc7d)
* ramips: backport upstream mt762x PCIe driver error log fixesShiji Yang2023-07-263-0/+102
| | | | | | | | | | | | | | | | | | | | | These patches silence some mt762x PCIe driver error messeges by removing the useless debugging codes and replacing incorrectly used 'dev_err()' with 'dev_info()': PCI: mt7621: Use dev_info() to log PCIe card detection [1] mips: pci-mt7620: do not print NFTS register value as error log [2] mips: pci-mt7620: use dev_info() to log PCIe device detection result [3] Patch [1] has already been merged into the Linux 6.3 branch. Patches [2] and [3] have been merged into the "mips-next" tree, and they will be part of the upcoming Linux 6.5. [1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?h=v6.4-rc7&id=50233e105a0332ec0f3bc83180c416e6b200471e [2] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=9f9a035e6156a57d9da062b26d2a48d031744a1e [3] https://git.kernel.org/pub/scm/linux/kernel/git/mips/linux.git/commit/?id=89ec9bbe60b61cc6ae3eddd6d4f43e128f8a88de Signed-off-by: Shiji Yang <yangshiji66@qq.com> (cherry picked from commit 4e74777fa8111a2bdf63164a4920a42917faec28)
* lantiq: add patches headersAleksander Jan Bajkowski2023-07-269-32/+129
| | | | | | | | This commit adds headers to the patches, so they can be applied with the git am command. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> (cherry picked from commit 5d51079fd064a86119c6f44920e737cf5e25d3a0)
* kernel: update patches for mediatek filogicFelix Baumann2023-07-261-1/+1
| | | | | | | | Fix complaint from actions Check Kernel patches (mediatek, filogic) https://github.com/openwrt/openwrt/actions/runs/5569719763/job/15081672586?pr=13072 Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* kernel: drop mips highmem offset start overridesFelix Fietkau2023-07-242-38/+0
| | | | | | | | | | | | The maximum offset that can be supported is 0x20000000 Do not override it to to something bigger than that on MT7621, as that could cause issues based on the fixed memory mappings. This makes the last 64 MB RAM unusable on MT7621 devices with 512 MB but avoids incurring a heavy performance hit Fixes: cd2b74e01e8d ("ramips: mt7621: disable highmem support and remove highmem offset patch") Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry picked from commit a110de8152df46a1e2adf7010ba75fb3b1236cd8)
* ramips: mt7621: disable highmem support and remove highmem offset patchFelix Fietkau2023-07-242-3/+19
| | | | | | | | | | | On MT7621 it was observed, that enabling highmem support causes a significant performance drop, as documented in: https://github.com/openwrt/openwrt/issues/13151 By adjusting the highmem start offset, we avoid leaving any RAM unaddressable, even on devices with 512 MB Fixes: https://github.com/openwrt/openwrt/issues/13151 Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry picked from commit cd2b74e01e8d5f5b80b82db1cb204c13ed99dd58)
* mediatek: add support for ZyXEL NWA50AX ProDavid Bauer2023-07-234-1/+257
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Mediatek MT7981 RAM: 512M DDR4 FLASH: 256M NAND ETH: MaxLinear GPY211 (2.5GbE N Base-T) WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax) BTN: 1x Reset LED: 1x Multi-Color UART Console ------------ Available below the rubber cover next to the ethernet port. Settings: 115200 8N1 Layout: <12V> <LAN> GND-RX-TX-VCC Logic-Level is 3V3. Don't connect VCC to your UART adapter! Installation Web-UI ------------------- Upload the Factory image using the devices Web-Interface. As the device uses a dual-image partition layout, OpenWrt can only installed on Slot A. This requires the current active image prior flashing the device to be on Slot B. In case this is not the case, OpenWrt will boot only one time, returning to the ZyXEL firmware the second boot. If this happens, first install a ZyXEL firmware upgrade of any version and install OpenWrt after that. Installation TFTP / Recovery ---------------------------- This installation routine is especially useful in case of a bricked device. Attach to the UART console header of the device. Interrupt the boot procedure by pressing Enter. The bootloader has a reduced command-set available from CLI, but more commands can be executed by abusing the atns command. Boot a OpenWrt initramfs image available on a TFTP server at 192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin. $ atnf nwa50axpro-openwrt-initramfs.bin $ atna 192.168.1.88 $ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff; bootm" Upon booting, set the booted image to the correct slot: $ zyxel-bootconfig /dev/mtd9 get-status $ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid $ zyxel-bootconfig /dev/mtd9 set-active-image 0 Copy the OpenWrt sysupgrade image to the device using scp. Write the sysupgrade image to NAND using sysupgrade. $ sysupgrade -n image.bin Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit f0445746f6fd96fc7c5394b238153bd2ff22bc5b)
* mediatek: filogic: set DEVICE_DTS_LOADADDR for BPi-R3Daniel Golle2023-07-221-0/+1
| | | | | | | | U-Boot complains that the overlayed DT needs relocation, so set DEVICE_DTS_LOADADDR to have it relocated. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit b1d10e0174f71099016a7e6dcd27b65a77fd51b4)
* octeon: ubnt-edgerouter-4/6p: devicetree cleanupCarsten Spieß2023-07-153-30/+10
| | | | | | | | | | | removed redundant eeprom partition nodes from cn7130_ubnt_edgerouter-4.dts and cn7130_ubnt_edgerouter-6p.dts as they are identically defined in cn7130_ubnt_edgerouter-e300.dtsi. Signed-off-by: Carsten Spieß <mail@carsten-spiess.de> (integrated eeprom referenced node in the .dtsi) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 700f11aaadb7baa38285ed8f928e976a29a72eed)
* octeon: ubnt-edgerouter-e300: fix missing MTD partitionCarsten Spieß2023-07-151-16/+22
| | | | | | | | | | | | | | | The MAC addresses should be read from 3rd MTD partition, but only two MTD partitions are populated. To fix it, a partitions node has to surround the partition nodes in device tree. Tested with Edgerouter 6P Signed-off-by: Carsten Spieß <mail@carsten-spiess.de> (fixed checkpatch complains) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 2b1d7965c7e74e1b31ff29a966eaf6334b0d7057)
* octeon: ubnt-edgerouter-e300: fix LED settingsCarsten Spieß2023-07-151-2/+2
| | | | | | | | | | | | | | LEDs on Edgerouter 6P didn't work correctly: blue /white LED swapped, on/off state inverted Fixed in device tree: swap the GPIO ports for power:blue and power:white LEDs change LED activity from LOW to HIGH Tested on Edgerouter 6P Signed-off-by: Carsten Spieß <mail@carsten-spiess.de> (cherry picked from commit 9009672930f7bda99ec8f6f09a92eb49b6c9aac8)
* armsr: v8: fix NVMEM_IMX_OCOTP_ELE build errorChristian Lamparter2023-07-151-0/+1
| | | | | | | | | | | there's a new symbol NVMEM_IMX_OCOTP_ELE that needs to be defined. otherwise the build will fail: | i.MX On-Chip OTP Controller support (NVMEM_IMX_OCOTP_ELE) [N/m/y/?] (NEW) | make[6]: *** [scripts/kconfig/Makefile:77: syncconfig] Error 1 | make[5]: *** [Makefile:628: syncconfig] Error 2 Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm53xx: backport DT changes queued for v6.6Rafał Miłecki2023-07-1410-4/+450
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 37ff916af789911fdefb802ce9903e866eb82435)
* mediatek: replace hack for MaxLinear 2.5G PHYDaniel Golle2023-07-133-166/+63
| | | | | | | Replace hack with proper patch also for Linux 5.15. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 712fa3eff82086da8a13e7e5bc577df17892a581)
* mediatek: dts: mt7988a: remove boottrap hackDaniel Golle2023-07-131-5/+0
| | | | | | | | The PHY driver now uses regmap created from pio syscon, we no longer need the boottrap device. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit f321a49fd523a8d393be8e3cd2de41d67855da91)
* mediatek: use backported Ethernet PHY driver also for 5.15Daniel Golle2023-07-134-1345/+1417
| | | | | | | | Backport in-SoC Gigabit Ethernet PHY driver instead of carrying the driver in files-5.15. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 9fac59009657068d5a58b3d0255d4ca1507dd457)
* mediatek: dts: mt7988a: wire-up mediatek,pio for PHY LEDsDaniel Golle2023-07-132-1/+2
| | | | | | | | | | | The PHY driver needs to read a register containing the values of the bootstrap pins (which happen to be the PHY LEDs) to determine the LED polarities. Allow regmap access to first pinctrl bank by adding the 'syscon' compatible, and reference the pinctrl in the MDIO bus where the PHY driver will look for it. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 1f1e0b1144ebaa4ba8b948a12d989a0a6fc9b76f)
* mediatek: filogic: add H3C Magic NX30 Pro supportChukun Pan2023-07-135-0/+278
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: W25N01GVZEIG 128MB RAM: NT5CB128M16JR-FL 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, WPS Power: DC 12V 1A Flash instructions: 1. PC run command: "telnet 192.168.124.1 99" Username: H3C, password is the web login password of the router. 2. Download preloader.bin and bl31-uboot.fip 3. PC run command: "python3 -m http.server 80" 4. Download files in the telnet window: "wget http://192.168.124.xx/xxx.bin" Replace xx with your PC's IP and the preloader.bin and bl31-uboot.fip. 5. Flushing openwrt's uboot: "mtd write xxx-preloader.bin BL2" "mtd write xxx-bl31-uboot.fip FIP" 6. Connect to the router via the Lan port, set a static ip of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 7. Download initramfs image, reboot router, waiting for tftp recovery to complete. 8. After openwrt boots up, perform sysupgrade. Note: 1. The u-boot-env partition on mtd is empty, OEM stores their env on ubi:u-boot-env. 2. Back up all mtd partitions before flashing. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> (cherry picked from commit e78d1a06c8a47be9ea5a306bfb43f3d7ceb89646)
* mediatek: add support for Netgear EX6250v2 seriesWenli Looi2023-07-134-0/+279
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear EX6250v2, EX6400v3, EX6410v2, EX6470 are wall-plug 802.11ac (Wi-Fi 5) extenders. Like other MT7629 devices, Wi-Fi does not work currently as there is no driver. Related: https://github.com/openwrt/openwrt/pull/5084 For future reference, 2.4GHz MAC = LAN+1, 5GHz MAC = LAN+2. Specifications: * MT7629, 256 MiB RAM, 16 MiB SPI NOR * MT7761N (2.4GHz) / MT7762N (5GHz) - no driver * Ethernet: 1 port 10/100/1000 * UART: 115200 baud (labeled on board) Installation: * Flash the factory image through the stock web interface, or TFTP to the bootloader. NMRP can be used to TFTP without opening the case. * After installation, perform a factory reset. Wait for the device to boot, then hold the reset button for 10 seconds. This is needed because sysupgrade in the stock firmware will attempt to preserve its configuration using sysupgrade.tgz. See https://github.com/openwrt/openwrt/pull/4182 Revert to stock firmware: * Flash the stock firmware to the bootloader using TFTP/NMRP. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> (cherry picked from commit 73de41898fcd06d837b013449c370c493bcdc595)
* image: add additional fields to Netgear encrypted imageWenli Looi2023-07-132-0/+11
| | | | | | | | | | | | | | | | | These fields are used for EAX12 and EX6250v2 series, and perhaps other devices. Compatibility is preserved with the WAX202 and WAX206. In addition, adds the related vars to DEVICE_VARS so that the variables work correctly with multiple devices. References in GPL source: https://www.downloads.netgear.com/files/GPL/EAX12_EAX11v2_EAX15v2_GPL_V1.0.3.34_src.tar.gz * tools/imgencoder/src/gj_enc.c Contains code that generates the encrypted image. Signed-off-by: Wenli Looi <wlooi@ucalgary.ca> (cherry picked from commit 0a1ebccc8702cadc50bc096f1e185472f3927786)
* ath79: DTS improvement for buzzer on RB951G-2HnDPavel Pernička2023-07-121-0/+6
| | | | | | | | | | | Mikrotik RB951 router has a buzzer on the board, which makes annoying noises due to the interference caused by PoE input or Wifi transmission when no GPIO pin state is set. I added buzzer node to device's DTS in order to set deault level to 1 and to provide easier access for it. Signed-off-by: Pavel Pernička <pernicka.pa@gmail.com> (cherry picked from commit dac0a133cf8dbf0bd9afabecdc1092456c451ec7)
* ath79: add support for MikroTik RB951G-2HnDMichał Kępień2023-07-125-0/+70
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MikroTik RB951G-2HnD is a wireless SOHO router that was previously supported by the ar71xx target, see commit 7a709573d7 ("ar71xx: add kernel support for the Mikrotik RB951G board"). Specifications -------------- - SoC: Atheros AR9344 (600 MHz) - RAM: 128 MB (2x 64 MB) - Storage: 128 MB NAND flash (various manufacturers) - Ethernet: Atheros AR8327 switch, 5x 10/100/1000 Mbit/s - 1x PoE in (port 1, 8-30 V input) - Wireless: Atheros AR9340 (802.11b/g/n) - USB: 2.0 (1A) - 8x LED: - 1x power (green, not configurable) - 1x user (green, not configurable) - 5x GE ports (green, not configurable) - 1x wireless (green, not configurable) - 1x button (restart) Unlike on the RB951Ui-2HnD, none of the LEDs on this device seem to be GPIO-controllable, which was also the case for older OpenWRT versions that supported this board via a mach file. The Ethernet port LEDs are controlled by the switch chip. See https://mikrotik.com/product/RB951G-2HnD for more details. Flashing -------- TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedures at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Michał Kępień <openwrt@kempniu.pl> (cherry picked from commit db02cecd6ad2e5962e6e9d8307da34855a083ad6)
* ath79: mikrotik: extract common bits for RB951x-2HnD devicesMichał Kępień2023-07-122-80/+83
| | | | | | | | | Mikrotik RouterBOARD 951Ui-2HnD and Mikrotik RouterBOARD RB951G-2HnD are very similar devices. Extract the DTS bits that are identical for these two boards to a separate DTSI file. Signed-off-by: Michał Kępień <openwrt@kempniu.pl> (cherry picked from commit c6ef4170945c6ab5432382110389f31fea92a76c)
* bcm53xx: backport DT changes from v6.5Rafał Miłecki2023-07-1125-9/+4634
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 8674b41c0d84f09e14bf8ebe08e1d6dc6ac5fa64)
* kernel: bgmac: fix regressed support for BCM53573 SoCsRafał Miłecki2023-07-101-0/+45
| | | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit d54f3b2cfdbd34aa61ca67fd590eebfdf3db51cf)
* bcm47xx: fix bgmac MTU patch filenameRafał Miłecki2023-07-101-0/+0
| | | | | | Fixes: 4970dd027bce ("bcm47xx: revert bgmac back to the old limited max frame size") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 83aeb0bbd47638b42ee6cdda351d0c51e014d790)
* kernel: backport NVMEM patches queued for the v6.5Rafał Miłecki2023-07-1013-1/+920
| | | | | | | This includes some driver changes and support for fixed cells layout. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> (cherry picked from commit 07bdc5551558287f7a99f6ae8e6d82d7d09d5781)
* kernel: net: phy: realtek: fix rtl822x_probe on unsupported devicesMartin Schiller2023-07-082-21/+5
| | | | | | | | | Calling rtl822x_probe() on phy devices which uses the rtl822x_read_mmd() and rtl822x_write_mmd() functions makes no sense and the probe ends with an EOPNOTSUPP error. Signed-off-by: Martin Schiller <ms@dev.tdt.de> (cherry picked from commit 5af7d47cd7fb936dc7d640e1ba63443152d0416a)
* ramips/mt7621: disable the cpufreq driverFelix Fietkau2023-07-081-7/+3
| | | | | | | It causes a noticeable performance decrease Signed-off-by: Felix Fietkau <nbd@nbd.name> (cherry picked from commit dc38199b96ee3ef0ac52873893c42e28fa0564fa)
* kernel: sort generic configurationAleksander Jan Bajkowski2023-07-081-1/+1
| | | | | | | | | | | | | This was done by executing these commands: $ ./scripts/kconfig.pl '+' target/linux/generic/config-5.15 /dev/null > target/linux/generic/config-5.15-new $ mv target/linux/generic/config-5.15-new target/linux/generic/config-5.15 $ ./scripts/kconfig.pl '+' target/linux/generic/config-6.1 /dev/null > target/linux/generic/config-6.1-new $ mv target/linux/generic/config-6.1-new target/linux/generic/config-6.1 Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> (cherry picked from commit 4f197f91342bc5e1f202c091c2c2f90e949d0749)
* kernel: bump 5.15 to 5.15.120John Audia2023-07-085-6/+6
| | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 0dc0504fc8e5f0c3cafe6c1da7192f51a09c5bc3)
* x86: set CONFIG_X86_AMD_PLATFORM_DEVICEJohn Audia2023-07-082-2/+2
| | | | | | | Needed by AMD processors using Carrizo and later chipsets Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 946100ba4128dbee8faf3c03afb692bca74d75fa)
* mxs: rework image generationZoltan HERPAI2023-07-065-100/+56
| | | | | | | | Migrate to "new" image generation method. Device profiles will be generated based on image/Makefile instead of profiles/ , which will also allow to automatically build images for all supported devices via buildbot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ipq-wifi: fix upstream board-2.bin ZTE M289F snafuChristian Lamparter2023-07-041-1/+1
| | | | | | | | | | | | | | | | | | | | | The upstream board-2.bin file in the linux-firmware.git repository for the QCA4019 contains a packed board-2.bin for this device for both 2.4G and 5G wifis. This isn't something that the ath10k driver supports. Until this feature either gets implemented - which is very unlikely -, or the upstream boardfile is mended (both, the original submitter and ath10k-firmware custodian have been notified). OpenWrt will go back and use its own bespoke boardfile. This unfortunately means that 2.4G and on some revisions the 5G WiFi is not available in the initramfs image for this device. Fixes: #12886 Reported-by: Christian Heuff <christian@heuff.at> Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 75505c5ec724b9b961dcb411bac1d4b9aede3e1d)
* ramips: mt7621: add TP-Link EAP613 v1Sander Vanheule2023-07-034-0/+166
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The TP-Link EAP613 v1 is a ceiling-mount 802.11ax access point. It can be powered via PoE or a DC barrel connector (12V). Connecting to the UART requires fine soldering and careful manipulation of any soldered wires. Device details: * SoC: MT7621AT * Flash: 16 MiB SPI NOR * RAM: 256 MiB DDR3L * Wi-Fi: * MT7905DA + MT7975D: 2.4 GHz + 5 GHz (DBDC), 2x2:2 * Two stamped metal antennas (ANT1, ANT2) * One PCB antenna (ANT3) * One unpopulated antenna (ANT4) * Ethernet: * 1× 10/100/1000 Mbps port with PoE * LEDs: * Array of four blue LEDs with one control line * Buttons: * Reset * Board test points: * UART: next to CPU RF-shield and power circuits * JTAG: under CPU RF-shield (untested) * Watchdog: 3PEAK TPV706 (not implemented) Althought three antennas are populated, the MT7905DA does not support the additional Rx chain for background DFS detection (or Bluetooth) according to commit 6cbcc34f50a3 ("ramips: disable unsupported background radar detection"). MAC addresses: * LAN: 48:22:54:xx:xx:a2 (device label) * WLAN 2.4 GHz: 48:22:54:xx:xx:a2 * WLAN 5 GHz: 48:22:54:xx:xx:a3 The radio calibration blob stored in flash also contains valid MAC addresses for both radio bands (OUI 00:0c:43). Factory install: 1. Enable SSH on the device via web interface 2. Log in with SSH, and run `cliclientd stopcs` 3. Upload -factory.bin image via web interface. It may be necessary to shorten the filename of the image to e.g. 'factory.bin'. Recovery: 1. Open the device by unscrewing four screws from the backside 2. Carefully remove board from the housing 3. Connect to UART (3.3V): * Find test points labelled "VCC", "GND", "UART_TX", "UART_RX" * Solder wires to test points or connect otherwise. Be careful not to damage the PCB e.g. by pulling on soldered wires. * Open console with 115200n8 settings 4. Interrupt bootloader and use tftpboot to start an initramfs: setenv ipaddr $DEVICE_IP setenv serverip $SERVER_IP tftpboot 84000000 openwrt-initramfs-kernel.bin bootm DO NOT use saveenv to store modified u-boot environment variables. The environment is saved at flash offset 0x30000, which erases part of the (secondary) bootloader. The device uses two bootloader stages. The first stage will load the second stage from a uImage stored at flash offset 0x10000. In case of a damaged second stage, the first stage should allow uploading a new image via y-modem (untested). Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit 11588c52b47c2c3b2cdc7849ce9e4804bfdb8bb5)
* mediatek: define NMBM management region for WAX220David Bauer2023-07-021-0/+5
| | | | | | | | | The NETGEAR WAX220 employs NMBM on SPI-NAND. In order to avoid dealing with invalid factory data, enable NMBM in the area preceding the UBI volume. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 92eec257dd562547bc08ee76c1901eb22b66937c)
* generic: filter out CONFIG_FRAME_WARNRobert Marko2023-07-021-0/+1
| | | | | | | | | | | | | | CONFIG_FRAME_WARN value is set by config/Config-kernel.in based on the target type dynamically since commit: 16a2051 ("kernel: Set CONFIG_FRAME_WARN depending on target"). However, CONFIG_FRAME_WARN was not set to get filtered out so it ended up in multiple target configs during refreshes. So, lets filter out CONFIG_FRAME_WARN as its set dynamically to prevent it ending up in more target configs. Signed-off-by: Robert Marko <robert.marko@sartura.hr> (cherry picked from commit 7a9a4168bb7f4b77c300afb99c163c793305e84f)
* zbt-wd323: add GPIO WDT supportJoshua O'Leary2023-07-021-0/+8
| | | | | | | | | | | | | | | Watchdog has not been properly configured for this router - the PCB has a hardware watchdog connected to one of the GPIO pin 21 [1] This commit provides this fix [2] Without this fix, the ZBT-WD323 is unusable in OpenWRT because it power cycles every 30 seconds due to the watchdog tripping [1] https://forum.openwrt.org/t/zbt-wd323-router-power-cycles-every-30-seconds/77535/7 [2] https://forum.openwrt.org/t/zbt-wd323-images-unusable-proposed-workaround/162145/5 Signed-off-by: Joshua O'Leary <josh.oleary@mobile-power.co.uk> (cherry picked from commit 008cc836fe42577af2843730dfefd31b750c7de6)
* ramips: add support for Sercomm S1500 devicesMikhail Zhilkin2023-07-027-3/+561
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for following wireless routers: - Beeline SmartBox PRO (Serсomm S1500 AWI) - WiFire S1500.NBN (Serсomm S1500 BUC) This commit is based on this PR: - Link: https://github.com/openwrt/openwrt/pull/4770 - Author: Maximilian Weinmann <x1@disroot.org> The opening of this PR was agreed with author. My changes: - Sorting, minor changes and some movings between dts and dtsi - Move leds to dts when possible - Recipes for the factory image - Update of the installation/recovery/return to stock guides - Add reset GPIO for the pcie1 Common specification -------------------- SoC: MediaTek MT7621AT (880 MHz, 2 cores) Switch: MediaTek MT7530 (via SoC MT7621AT) Wireless: 2.4 GHz, MT7602EN, b/g/n, 2x2 Wireless: 5 GHz, MT7612EN, a/n/ac, 2x2 Ethernet: 5 ports - 5×GbE (WAN, LAN1-4) Mini PCIe: via J2 on PCB, not soldered on the board UART: J4 -> GND[], TX, VCC(3.3V), RX BootLoader: U-Boot SerComm/Mediatek Beeline SmartBox PRO specification ---------------------------------- RAM (Nanya NT5CB128M16FP): 256 MiB NAND-Flash (ESMT F59L2G81A): 256 MiB USB ports: 2xUSB2.0 LEDs: Status (white), WPS (blue), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (reset, wps), 1 switch button (ROUT<->REP) Power: 12 VDC, 1.5 A PCB Sticker: 970AWI0QW00N256SMT Ver. 1.0 CSN: SG15******** MAC LAN: 94:4A:0C:**:**:** Manufacturer's code: 0AWI0500QW1 WiFire S1500.NBN specification ------------------------------ RAM (Nanya NT5CC64M16GP): 128 MiB NAND-Flash (ESMT F59L1G81MA): 128 MiB USB ports: 1xUSB2.0 LEDs: Status (white), WPS (white), 2g (white), 5g (white) + 10 LED Ethernet Buttons: 2 button (RESET, WPS) Power: 12 VDC, 1.0 A PCB Sticker: 970BUC0RW00N128SMT Ver. 1.0 CSN: MH16******** MAC WAN: E0:60:66:**:**:** Manufacturer's code: 0BUC0500RW1 MAC address table (PRO) ----------------------- use address source LAN *:23 factory 0x1000 (label) WAN *:24 factory $label +1 2g *:23 factory $label 5g *:25 factory $label +2 MAC addresses (NBN) ------------------- use address source LAN *:0e factory 0x1000 WAN *:0f LAN +1 (label) 2g *:0f LAN +1 5g *:10 LAN +2 OEM easy installation --------------------- 1. Remove all dots from the factory image filename (except the dot before file extension) 2. Upload and update the firmware via the original web interface 3. Two options are possible after the reboot: a. OpenWrt - that's OK, the mission accomplished b. Stock firmware - install Stock firmware (to switch booflag from Sercomm0 to Sercomm1) and then OpenWrt factory image. Return to Stock --------------- 1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot: printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock2 reboot 2. Install stock firmware via the web OEM firmware interface Recovery -------- Use sercomm-recovery tool. Link: https://github.com/danitool/sercomm-recovery Tested-by: Pavel Ivanov <pi635v@gmail.com> Tested-by: Denis Myshaev <denis.myshaev@gmail.com> Tested-by: Oleg Galeev <olegingaleev@gmail.com> Tested-By: Ivan Pavlov <AuthorReflex@gmail.com> Co-authored-by: Maximilian Weinmann <x1@disroot.org> Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit 2d6784a033a994043759fa3b94c48afd5df81f88)
* ramips: sercomm.mk: preparation for Sercomm s1500 devices supportMikhail Zhilkin2023-07-021-5/+9
| | | | | | | | | | | | | | This commit moves a part of the code from the "sercomm-factory-cqr" recipe to the separate "sercomm-mkhash" recipe. This simplifies recipes and allows insert additional recipes between these code blocks (required for the future support for Beeline SmartBox PRO router). dd automatically fills the file by 0x00 if the filesize is less than offset where we start writing. We drop such dd command so we need to add --extra-padding-size 0x190 to the sercomm-pid.py call. Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit f560be583a858bc3099f2b1f0aa0ddec62cfd91c)
* kernel: bump 5.15 to 5.15.119John Audia2023-07-0230-129/+129
| | | | | | | | | Build system: x86_64 Build-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3 Run-tested: x86_64/ACEMAGICIAN T8PLUS, ramips/tplink_archer-a6-v3 Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 42cb0f0f260484ac07e3d698ebc5c546e1800051)
* mediatek: add support for Mercusys MR90X v1Mikhail Zhilkin2023-07-019-0/+357
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Mercusys MR90X(EU) v1 router. Device specification -------------------- SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit RAM: MediaTek MT7986BLA (512MB) Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB) Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8) Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2) WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4 WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4 LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs on ethernet ports Button: 1 (Reset) USB ports: No Power: 12 VDC, 2 A Connector: Barrel Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI slots contain "seconduboot" (also U-Boot 2022.01-rc4) Serial console (UART) --------------------- V +-------+-------+-------+-------+ | +3.3V | GND | TX | RX | +---+---+-------+-------+-------+ | +--- Don't connect The R3 (TX line) and R6 (RX line) are absent on the PCB. You should solder them or solder the jumpers. Installation (UART) ------------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm 4. Once inside OpenWrt, set / update env variables: fw_setenv baudrate 115200 fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv fdtcontroladdr 5ffc0e70 fw_setenv ipaddr 192.168.1.1 fw_setenv loadaddr 0x46000000 fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)" fw_setenv netmask 255.255.255.0 fw_setenv serverip 192.168.1.2 fw_setenv stderr serial@11002000 fw_setenv stdin serial@11002000 fw_setenv stdout serial@11002000 fw_setenv tp_boot_idx 0 5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image Installation (without UART) --------------------------- 1. Login as root via SSH (router IP, port 20001, password - your web interface password) 2. Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and SSH settings from the p.1) 3. Add a newline after "#!/bin/sh": telnetd -l /bin/login.sh 4. Save "65-iptv" file 5. Toggle "IPTV/VLAN Enable" checkbox in the router web interface and save 6. Make sure that telnetd is running: netstat -ltunp | grep 23 7. Login via telnet to router IP, port 23 (no username and password are required) 8 Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the router (e.g., using WinSCP and SSH settings from the p.1) 9. Stock busybox doesn't contain ubiupdatevol command. Hence, we need to download and upload the full version of busybox to the router. For example, from here: https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64 Upload busybox-arm64 to the /tmp dir of the router and run: in the telnet shell: cd /tmp chmod a+x busybox-arm64 10. Check "initramfs-kernel.bin" size: du -h initramfs-kernel.bin 11. Delete old and create new "kernel" volume with appropriate size (greater than "initramfs-kernel.bin" size): ubirmvol /dev/ubi0 -N kernel ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB 12. Write OpenWrt "initramfs-kernel.bin" to the flash: ./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin 13. u-boot-env can be empty so lets create it (or overwrite it if it already exists) with the necessary values: fw_setenv baudrate 115200 fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv fdtcontroladdr 5ffc0e70 fw_setenv ipaddr 192.168.1.1 fw_setenv loadaddr 0x46000000 fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)" fw_setenv netmask 255.255.255.0 fw_setenv serverip 192.168.1.2 fw_setenv stderr serial@11002000 fw_setenv stdin serial@11002000 fw_setenv stdout serial@11002000 fw_setenv tp_boot_idx 0 14. Reboot to OpenWrt initramfs: reboot 15. Login as root via SSH (IP 192.168.1.1, port 22) 16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router 17. Run sysupgrade: sysupgrade -n /tmp/sysupgrade.bin Recovery -------- 1. Press Reset button and power on the router 2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and upload the OEM firmware Recovery (UART) --------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm 4. Do what you need (restore partitions from a backup, install OpenWrt etc.) Stock layout ------------ 0x000000000000-0x000000200000 : "boot" 0x000000200000-0x000000300000 : "u-boot-env" 0x000000300000-0x000003500000 : "ubi0" 0x000003500000-0x000006700000 : "ubi1" 0x000006700000-0x000006f00000 : "userconfig" 0x000006f00000-0x000007300000 : "tp_data" ubi0/ubi1 format ---------------- U-Boot at boot checks that all volumes are in place: +-------------------------------+ | Volume Name: uboot Vol ID: 0| | Volume Name: kernel Vol ID: 1| | Volume Name: rootfs Vol ID: 2| +-------------------------------+ MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | label | 00:eb:xx:xx:xx:be | label | | LAN | 00:eb:xx:xx:xx:be | label | | WAN | 00:eb:xx:xx:xx:bf | label+1 | | WLAN 2g | 00:eb:xx:xx:xx:be | label | | WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 | +---------+-------------------+-----------+ label MAC address was found in UBI partition "tp_data", file "default-mac". OEM wireless eeprom is also there (file "MT7986_EEPROM.bin"). Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com> (cherry picked from commit e4fe3097ef6a961874b66932a0ac4be18070630a) [Fix merging conflict] Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
* ipq4019: add support for ZTE MF287+ aka DreiNeoAndreas Böhler2023-07-014-0/+408
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF287+ is a LTE router used (exclusively?) by the network operator "3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only difference is the LTE modem) Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287) WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m14 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd13 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 14 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit f70ee53b08466f612546f699c556cbdaa39e1466)
* ipq40xx: Enable gpio-restart in kernel configurationAndreas Böhler2023-07-011-0/+1
| | | | | | | | Some ZTE devices require the gpio-restart driver to support restarting the LTE modem along with OpenWrt Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit 9ffdaa7fa1478146b5d8c77d4b3a5d4d4007a487)
* filogic: add support for Netgear WAX220Flole Systems2023-06-265-0/+321
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SOC: MediaTek MT7986 RAM: 1024MB DDR3 FLASH: 128MB SPI-NAND (Winbond) WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz ETH: Realtek RTL8221B-VB-CG 2.5 N-Base-T PHY with PoE UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC) Installation ------------ 1. Download the OpenWrt initramfs image. Copy the image to a TFTP server 2. Connect the TFTP server to the WAX220. Conect to the serial console, interrupt the autoboot process by pressing '0' when prompted. 3. Download & Boot the OpenWrt initramfs image. $ setenv ipaddr 192.168.2.1 $ setenv serverip 192.168.2.2 $ tftpboot openwrt.bin $ bootm 4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using scp and install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Signed-off-by: Flole Systems <flole@flole.de> Signed-off-by: Stefan Agner <stefan@agner.ch> (cherry picked from commit 984786a2f7ec622c99e8c9cdada65d0ea0cf4e0b)
* kernel: bump 5.15 to 5.15.118John Audia2023-06-2538-48/+48
| | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 1f5fce27c195373fedcf233a48470de97752058f)
* ipq40xx: meraki-mr33, meraki-mr74: disable image generationLech Perczak2023-06-251-0/+2
| | | | | | | | | | | | | | After migrating to kernel 5.15, upgrading causes the units to become soft-bricked, hanging forever at the kernel startup. Kernel size limitation of 4000000 bytes is suspected here, but this is not fully confirmed. Disable the images to protect users from inadvertent bricking of units, because recovery of those is painful with Cisco's U-boot, until the root cause is found and fixed. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit 9d64cc068fbb15d9e6498c1eba79851823b2f4f5)
* ramips: fix lan leds for Wavlink WL-WN535K1Davide Fioravanti2023-06-253-5/+5
| | | | | | | | | | Previously both lan1 and lan2 leds were wrongly labelled as lan2. Moreover they were connected to the wrong lan port. Fixes 8fde82095ba0 ("ramips: add support for Wavlink WL-WN535K1") Reported-by: Nicolò Maria Semprini <nicosemp@gmail.com> Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> (cherry picked from commit c71dada92654a53c63bbc5bebcc40fe924750ed7)
* ramips: mt7621: add support for Zbtlink ZBT-WG1608 (32M)Kim DoHyoung2023-06-253-1/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G) modems. Specifications: * SoC: MediaTek MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * Wi-Fi: * MediaTek MT7603E : 2.4Ghz * MediaTek MT7613BE : 5Ghz * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * M.2: 1x slot with USB&SIM * EM7455/EM12-G/EM160R/RM500Q-AE * USB: 1x 3.0 Type-A port * External storage: 1x microSD (SDXC) slot * UART: console (115200 baud) * LED: * 1 power indicator * 1 WLAN 2.4G controlled (wlan 2G) * 3 SoC controlled (wlan 5G, wwan, internet) * 5 per Eth phy (4xLAN + WAN) MAC Addresses: * LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex)) * WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex)) * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex)) * 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex)) Installation: * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Recovery Mode: * Press reset button, power up the device, wait for about 10sec. * Upload sysupgrade image through the firmware recovery mode web page at 192.168.1.1. Signed-off-by: Kim DoHyoung <azusahmr@k-on.kr> (cherry picked from commit 0bbd5699c81d6887c4d895e85b56d8c23b1211ec)
* ath79: add support for Aruba AP-115David Bauer2023-06-233-0/+260
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== CPU Qualcomm Atheros QCA9558 RAM 256MB DDR2 FLASH 2x 16M SPI-NOR (Macronix MX25L12805D) WIFI Qualcomm Atheros QCA9558 Atheros AR9590 Installation ============ 1. Attach to the serial console of the AP-105. Interrupt autoboot and change the U-Boot env. $ setenv rb_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; netget 0x80060000 ap115.bin; go 0x80060000" $ setenv fb_openwrt "bank 1; cp.b 0xbf100040 0x80060000 0x10000; go 0x80060000" $ setenv bootcmd "run fb_openwrt" $ saveenv 2. Load the OpenWrt initramfs image on the device using TFTP. Place the initramfs image as "ap105.bin" in the TFTP server root directory, connect it to the AP and make the server reachable at 192.168.1.66/24. $ run rb_openwrt 3. Once OpenWrt booted, transfer the sysupgrade image to the device using scp and use sysupgrade to install the firmware. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 1b467a902ec9b8bf29805c6928627e8bbad0f14c)
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-25 19:36:24 +0000