aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ramips: increase spi-max-frequency to 50 MHz for D-Link DIR-810LAdrian Schmutzler2020-03-051-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Read times drop when increasing frequency to 25 MHz and 50 MHz, but not in between or for further increase. So, use 50 MHz as the lowest frequency with the fastest speed. Test results (thanks to Roger): The device reports a mx25l6405d flash chip. I tried all the maximum values in the devices' datasheet (Table 10. AC CHARACTERISTICS). All of them worked with and without "m25p,fast-read": > 10 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 1m 33.00s user 0m 0.01s sys 1m 7.56s > 25 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 34.42s user 0m 0.02s sys 0m 23.58s > 25 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 34.45s user 0m 0.02s sys 0m 23.59s > 33 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 34.39s user 0m 0.00s sys 0m 23.60s > 33 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 34.46s user 0m 0.01s sys 0m 23.62s > 50 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.81s user 0m 0.01s sys 0m 18.25s > 50 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.84s user 0m 0.00s sys 0m 18.25s > 66 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.80s user 0m 0.01s sys 0m 18.23s > 66 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.80s user 0m 0.02s sys 0m 18.23s > 86 MHz root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.84s user 0m 0.01s sys 0m 18.24s > 86 MHz, fast read root@OpenWrt:~# time cat /dev/mtd* > /dev/null real 0m 26.80s user 0m 0.02s sys 0m 18.23s Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: fix and tidy up DTS for D-Link DIR-810LAdrian Schmutzler2020-03-051-8/+10
| | | | | | | | | | | | | This patch addresses several issues for D-Link DIR-810L: - add correct button codes - harmonize button node names - use generic flash@0 - remove unused pin groups from state_default - improve sorting of properties Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: fix partition offset for D-Link DIR-810LAdrian Schmutzler2020-03-051-2/+2
| | | | | | | | | | | | | | The Jffs2 partition for the D-Link DIR-810L is currently off by 0x10000. Apply the correct offset based on the other partitions' size/offset and the information about stock OS from the Wiki. This is just based on the named information and _not_ verified on device. Fixes: 36e3424fa520 ("ramips: add support for dir810l and asus rp-n53") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ipq806x: add newline at the end of qcom-ipq8064-v1.0.dtsiAdrian Schmutzler2020-03-051-1/+1
| | | | | | | The file does not have a newline at the end. Add it to apply to common style. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: fix support of EnGenius EAP2200Adrian Schmutzler2020-03-053-21/+21
| | | | | | | | | | | | This fixes a typo in the device string for MAC address setup in 02_network and corrects the indent in the device's DTS files. While at it, move the aliases section before the keys section to have it closer to the top of the file. Fixes: a736d912e2ba ("ipq40xx: add support for EnGenius EAP2200") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for NETGEAR R6700v2/AC2400Adrian Schmutzler2020-03-045-0/+141
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 256M DDR3 FLASH: 128M NAND WiFi: MediaTek MT7615N an+ac MediaTek MT7615N bgn ETH: MediaTek MT7621AT BTN: 1x Connect (WPS), 1x WLAN, 1x Reset LED: Power (white/amber), WAN(white/amber), 2.4G(white), 5G(white), USB(white) , GuestWifi(white) 4x LAN(white/amber), Wifi Button(white), WPS Button(white) Installation: Login to netgear webinterface and flash factory.img Based on a discontinued GitHub Pull Request by kuyokushin <codenamezero@protonmail.com> https://github.com/openwrt/openwrt/pull/2545 NOTE: Netgear R6700 v2 have five clones: R6900 v2, R7450, Nighthawk AC2400, Nighthawk AC2100 and already added R6800. Rest of them should be really easy supportable. Image for R6700v2 should work perfectly with them. Please refer: https://github.com/openwrt/openwrt/pull/2614 Tested-by: Víctor Gibrán <victorgibranmz@hotmail.com> [R6700v2] Tested-by: John Landrum <jl31m10@yahoo.com> [AC2400] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [add guest led to mt7621_netgear_r6700-v2.dts end edit commit message] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: mt7621: add support for Netgear R6800Pawel Dembicki2020-03-047-0/+272
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6800, aka Netgear AC1900 and R6800-100PES. Specification: - SoC: MediaTek MT7621AT (880 MHz) - Flash: 128 MiB NAND - RAM: 256 MiB - Wireless: MediaTek MT7615EN b/g/n , MediaTek MT7615EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - USB 2.0 - USB 3.0 - Serial baud rate of Bootloader and factory firmware: 57600 Known issues: - Device has 3 wifi LEDs: Wifi 5Ghz, Wifi 2.4Ghz and Wifi on/off. Wifi on/off is not used. Installation: - apply factory image via stock web-gui. Back to stock: - nmrpflash can be used to recover to the stock Netgear firmware. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq806x: add 5.4 as testing kernel versionAnsuel Smith2020-03-031-0/+1
| | | | | | | | | | | Add 5.4 kernel version as a new testing kernel option. Ref: https://github.com/openwrt/openwrt/pull/2793 Tested-by: Hannu Nyman <hannu.nyman@iki.fi> [ipq8065, R7800] Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ipq8065, NBG6817] Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [added Tested-by tags] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* generic: add missing symbol from 5.4 configAnsuel Smith2020-03-031-0/+19
| | | | | | Add missing symbol displayed with ipa806x kernel config Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: fix broken stmmac notifierAnsuel Smith2020-03-031-0/+84
| | | | | | | Backport a patch in 5.6 to fix stmmac notifier registration Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: add patch to fix broken usb3Ansuel Smith2020-03-031-0/+29
| | | | | | | | | Due to changes in syscon driver, the phy dwc3 driver needs to use device_node_to_regmap since it has to skip the new introduced clk check. This fix broken usb3 on this target. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: move mdio node to ipq8064 dtsAnsuel Smith2020-03-0315-540/+410
| | | | | | | As mdio0 is used in every dts move it to general ipq8064 dts and use label to set device specific definition. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: rework dts to use labelAnsuel Smith2020-03-0313-2695/+2698
| | | | | | We should use label instead of redefine the node. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: remove wrong compatible from timer nodeAnsuel Smith2020-03-031-2/+1
| | | | | | This compatible definition deprecated long ago. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: add patch to disable pretimeout on timer platformAnsuel Smith2020-03-031-0/+98
| | | | | | | | | Currently the watchdog timer is broken as it tries to get an interrupt to setup pretimeout. Since our platform have a different type of interrupt disable it and use legacy watchdog probe. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: use mdio dedicated driverAnsuel Smith2020-03-0314-70/+137
| | | | | | | Enable kernel config flag Convert all dts to use the new mdio driver Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: add ipq806x mdio driverAnsuel Smith2020-03-031-0/+206
| | | | | | | | | This was created by Chunkeey some time ago. Since mdio driver works or doesn't work and since this was tested by me for 1 year, include it to remove the use of the generic bitbang gpio driver for switch driver. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: update config for kernel 5.4Ansuel Smith2020-03-031-22/+56
| | | | | | Adds new symbol and update flag with new kernel names. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: fix tsens driverAnsuel Smith2020-03-035-178/+231
| | | | | | | | | | Rework tsens driver. Since in the new kernel 5.4 init common do more than it should, inizialize the kernel memory directly in the driver and drop use of this function. Rework all the patch with the new variable names. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: rework L2 cache patchAnsuel Smith2020-03-031-16/+54
| | | | | | | | Rework l2 scaling patch to fix some compile warning and to imporve the caling timings by removing call to unnecessary function. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: update nvmem cpufreq driverAnsuel Smith2020-03-031-31/+36
| | | | | | | Rework the nvmem cpufreq driver to reflect changed in kernel 5.4 Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: drop upstream patchAnsuel Smith2020-03-0316-2941/+0
| | | | | | This patchset has been merged upstream. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: refresh patches for kernel 5.4Ansuel Smith2020-03-0328-112/+118
| | | | | | Refresh patches and minor changes for new kernel support Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: correct wrong node in r7800 dtsAnsuel Smith2020-03-031-5/+7
| | | | | | A mux node was missing in the gpio node of the r7800 dts. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: use correct definition for nand-controller nodeAnsuel Smith2020-03-0313-22/+22
| | | | | | From kernel Documentation this should be called nand-controller Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: include ipq806x-v1.0 dtsiAnsuel Smith2020-03-031-0/+1
| | | | | | | Since this dtsi now have wrong definition in the upstream version, include it to overwrite and remove any problem. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: remove skeleton definitionAnsuel Smith2020-03-031-4/+7
| | | | | | This was already deprecated. With kernel 5.4 it has been removed. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: copy files to kernel 5.4Ansuel Smith2020-03-0374-0/+16474
| | | | | | Copy files to kernel 5.4 to start porting. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* kirkwood: switch kernel version to 5.4Pawel Dembicki2020-03-031-3/+1
| | | | | | | | | | | | | 5.4 support is ready and tested. Compile tested: all target devices Run tested: pogoplug v4, nsa310b and two unofficial supported devices Tested-by: Sungbo Eo <mans0n@gorani.run> Tested-by: Alberto Bursi <alberto.bursi@outlook.it> [pogoplug v4 and nsa310b] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [fixed the switch, removed maintainer variable] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kirkwood: fix switch dts node in EA4500 and EA3500Pawel Dembicki2020-03-032-77/+22
| | | | | | | | | | | | Changes made in switch nodes in d42c9ce commit causes problem with correct mvsw61xx detection. This commit undo that changes. mvsw61xx is platform driver, so it need to be in main root of dts. Fixes: d42c9ce326aa ("kirkwood: add kernel 4.19 support") Tested-by: Marcin Fedan <mfedan@gmail.com> [EA4500] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: initial refresh of 5.4 patchesPawel Dembicki2020-03-033-70/+21
| | | | | | | | | | Refreshed all patches. Changed: 105-ea4500.patch-> Upstream DSA driver was updated. Patch was fixed 202-linksys-find-active-root.patch -> Upstream driver was moved. Patch was fixed Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: initial refresh 5.4 configPawel Dembicki2020-03-031-16/+38
| | | | | | Refreshed kernel config with updated NAND config. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: copy files and config from 4.19 to 5.4Pawel Dembicki2020-03-0317-0/+1721
| | | | | | | This commit is simple copy config, files and patches from 4.19 to 5.4 kernel. No changes was done. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* mediatek: update uci-defaults for renamed smp packet steering optionAlan Swanson2020-03-031-4/+1
| | | | | | | | Leave as enabled by default for mediatek. Also remove obsolete settings from when packet steering was moved from netifd to a simplified hotplug script. Signed-off-by: Alan Swanson <reiver@improbability.net>
* ramips: mt7530: more detailed output for unexpected etag_ctrlYousong Zhou2020-03-031-1/+2
| | | | Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* ramips: mt7530: remove redundant global attrs for port mirroringYousong Zhou2020-03-031-88/+0
| | | | | | | | | | | | | | | | | | | | Global attributes enable_mirror_tx/enable_mirror_rx depend on runtime value of another global attribute mirror_source_port which just resides in the memory The same functionality can be achieved by directly setting port attribute of the same names. E.g. the following two groups of commands achieve the same thing swconfig dev switch0 set mirror_source_port 3 swconfig dev switch0 set enable_mirror_tx 1 swconfig dev switch0 set mirror_source_port 4 swconfig dev switch0 set enable_mirror_tx 1 swconfig dev switch0 port 3 set enable_mirror_tx 1 swconfig dev switch0 port 4 set enable_mirror_tx 1 Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* bcm53xx: fix ASUS firmwares to use vendor formatRafał Miłecki2020-03-021-6/+13
| | | | | | | | Image building process was missing "asus-trx" step which resulted in raw TRX files (without ASUS footer with device id). Fixes: 0b9de8daa70e ("bcm53xx: add profiles for all other (SoftMAC) devices") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: x86_64: drop CALGARY IOMMU on 5.4Kevin Darbyshire-Bryant2020-03-021-2/+2
| | | | | | It's snuck back in on kernel 5.4 configs, so drop it there too. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: mt7620: disable images for Netgear 2700Petr Štetiar2020-03-021-0/+1
| | | | | | Because openwrt-ramips-mt7620-netgear_ex2700-squashfs-factory.bin is too big. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: add missing LED migration for Archer C7David Bauer2020-03-011-0/+3
| | | | | | | | | | | | When changing the LED names for the Archer C7 to represent the correct color, a migration for existing UCI entries was not created. Add a migration to keep existing LED configurations working. Fixes commit c79c001b593b ("ar71xx: Archer C7 v1 LED names and RFKILL fixes") Signed-off-by: David Bauer <mail@david-bauer.net>
* x86: add preinit hook for bootloader upgradeTomasz Maciej Nowak2020-03-012-1/+21
| | | | | | | | | | | | | | | | This commit fills the void for current OpenWrt installations which will be still on old bootloader version even after "x86: add bootloader upgrade on sysupgrade", since it performs bootloader upgrade only on sysupgrade. To keep all OpenWrt deploynents on the same GRUB version, add preinit hook, which will perform upgrade of the bootloader on first boot after sysupgrade. It's temporary solution and should be deleted, when the first release including this hook will no longer be supported by OpenWrt team. We can assume that all installations should be on current bootolader version and from there sysupgrade routine will be sufficient. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: add bootloader upgrade on sysupgradeTomasz Maciej Nowak2020-03-012-3/+28
| | | | | | | | | | | | | | Currently bootloader always stays on the same version as when first written to boot medium (not true if partition layout changed, which will trigger sysupgrade process to write full disk image). That creates inconveniences as it always stays with same features or/and bugs. Users wishing to add support to additional modules or new version, would need to write the whole image, potentially destroying previous system configuration. To fix these, this commit adds additional routine to sysupgrade which upgrades unconditionally the bootloader to the latest state provided by OpenWrt. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* x86: image: cleanup before creating imageTomasz Maciej Nowak2020-03-011-0/+2
| | | | | | | | | There can be some leftovers from other image recipes, if the same directory names are used and multiply image types are selected. Therefore remove directories used in the recipe, before contents for the image are prepared. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* imx6: 5.4: dts: backport lsm9ds1 imu support for GW553xTim Harvey2020-03-011-0/+73
| | | | | | | | | Add one node for the accel/gyro i2c device and another for the separate magnetometer device in the lsm9ds1. Signed-off-by: Tim Harvey <tharvey@gateworks.com> [commit subject/description tweaks, kernel version in patch filename] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: 5.4: backport fxos8700 accel support from 5.5Tim Harvey2020-03-011-0/+912
| | | | | | | | | | | | Backport kernel module from 5.5 for FXOS8700CQ, which is a small, low-power, 3-axis linear accelerometer and 3-axis magnetometer combined into a single package. The device features a selectable I2C or point-to-point SPI serial interface with 14-bit accelerometer and 16-bit magnetometer ADC resolution along with smart-embedded functions. Signed-off-by: Tim Harvey <tharvey@gateworks.com> [added commit description] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* mvebu: uDPU: drop patch compiling dtbTomasz Maciej Nowak2020-03-012-11/+1
| | | | | | | | | If device recipe has specified DEVICE_DTS variable, the dtb is built anyway by OpenWrt buildroot image rules. Drop the patch and adjust the location of compiled dtb. Cc: Scott Roberts <ttocsr@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: rework uDPU-firmware recipeTomasz Maciej Nowak2020-03-011-3/+9
| | | | | | | | | Tar has ability to change current dir, so use that instead additional command invocation. Also being here, change tar arguments to make final archive reproducible. Cc: Scott Roberts <ttocsr@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: uDPU: clean package selectionTomasz Maciej Nowak2020-03-011-3/+1
| | | | | | | | | This device receipe selects bunch of packages which some are re-defined, unnecessary or irrelevant. Clean them up, so only basic functionality persist. Cc: Scott Roberts <ttocsr@gmail.com> Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: image: keep global DTS_DIR intactTomasz Maciej Nowak2020-03-011-1/+2
| | | | | | | | Don't rewrite global DTS_DIR, instead, use proper variable for specifying devices dts directory. For consistency, also specify the variable in default profile, as suggested by Adrian Schmutzler. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* ar71xx: correct AVM FRITZ Repeater 450E WPS button flagDavid Bauer2020-03-011-1/+1
| | | | | | | | | The AVM FRITZ!WLAN Repeater 450E's WPS button is not active low. Correct the active low flag to avoid unintenional activation of failsafe mode on boot. Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 14:34:11 +0000