aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* mediatek: new target ubnt_unifi-6-lr-v1-ubootmodHenrik Riomar2022-07-042-5/+6
| | | | | | | | | based on current ubnt_unifi-6-lr-ubootmod Signed-off-by: Daniel Golle <daniel@makrotopia.org> [added SUPPORTED_DEVICES for compatibility with existing setups] Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com> (cherry picked from commit 5c8d3893a78fd81454930de30d90efaef99f8734)
* mediatek: new target mt7622-ubnt-unifi-6-lr-v1Henrik Riomar2022-07-045-31/+35
| | | | | | | | | | | | | Based on current mt7622-ubnt-unifi-6-lr, this is a preparation for adding a v2 version of this target * v1 - with led-bar * v2 - two simple GPIO connected LEDs (in later commits) Signed-off-by: Daniel Golle <daniel@makrotopia.org> [added SUPPORTED_DEVICES for compatibility with existing setups] Signed-off-by: Henrik Riomar <henrik.riomar@gmail.com> (cherry picked from commit 15a02471bb854245f8f94398c1e1d9ce29c2c341)
* mediatek: build ubnt-ledbar as a moduleChuanhong Guo2022-07-044-4/+18
| | | | | | | | | The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because of its I2C dependency. Build it as a module and let buildroot handle this config option instead. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> (cherry picked from commit d9ea9c06e98b597174e0e94e0a13934637c0c03e)
* mediatek: remove crypto-hw-mtk packageEneas U de Queiroz2022-07-041-23/+0
| | | | | | | | The MediaTek's Crypto Engine module is only available for mt7623, in which case it is built into the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit 3f2d0703b60357e3ff1865783335be9f51528eb8)
* mediatek: mt7622: fix banana pi r64 wps buttonNick Hainke2022-07-041-0/+40
| | | | | | | | | | | | | | | | Fix the wps button to prevent wrongly detected recovery procedures. In the official banana pi r64 git the wps button is set to GPIO_ACTIVE_LOW and not GPIO_ACTIVE_HIGH. Import patch to fix on boot unwanted recovery entering: Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level - failsafe button wps was pressed - - failsafe - Signed-off-by: Nick Hainke <vincent@systemli.org> (cherry-picked from commit 668619425526cb0d43f8536a2f6f15a6314e6553)
* mediatek/mt7629: Activate CONFIG_ARM_ARCH_TIMER_EVTSTREAMHauke Mehrtens2022-07-031-0/+2
| | | | | | | | | | The kernel configuration option CONFIG_MACH_MT7629 selects CONFIG_HAVE_ARM_ARCH_TIMER now. Handle this change in the config-5.10. This fixes some build problems. Fixes: 81530d69ef58 ("kernel: bump 5.10 to 5.10.121") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Refresh patches for all targetsHauke Mehrtens2022-07-0336-155/+79
| | | | | | | | | | | | | | | | This refreshes the patches on top of kernel 5.4.127. Deleted (upstreamed): bcm27xx/patches-5.10/950-0005-Revert-mailbox-avoid-timer-start-from-callback.patch [0] bcm27xx/patches-5.10/950-0678-bcm2711_thermal-Don-t-clamp-temperature-at-zero.patch [1] Needed manual modifications: bcm27xx/patches-5.10/950-0410-drm-atomic-Pass-the-full-state-to-CRTC-atomic-begin-.patch [0]: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.127&id=bb2220e0672b7433a9a42618599cd261b2629240 [1]: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.127&id=83603802954068ccd1b8a3f2ccbbaf5e0862acb0 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ramips: improve YunCore AX820 LEDsThibaut VARÈNE2022-07-011-6/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At least two AX820 hardware variants are known to exist, but they cannot be distinguished (same hardware revision, no specific markings). They appear to have the same LED hardware, but wired differently: - One has a red system LED at GPIO 15, a green wlan2g LED at GPIO 14 and a blue wlan5g LED at GPIO 16; - The other only offers a green system LED at GPIO 15, with GPIO 14 and 16 being apparently not connected Finally, a Yuncore datasheet says the canonical wiring should be: - Blue wlan2g GPIO 14, green system GPIO 15, red wlan5g GPIO 16 All GPIOs are tied to a single RGB LED which is exposed via lightpipe on the device front casing. Considering the above, this patch exposes all three LEDs, preserves the common system LED (GPIO 15) as the openwrt status LED, and removes the color information from the LEDs names since it is not consistent across hardware. The LED naming is made consistent with other YunCore devices. A note is added in DTS to ensure this information is always available and prevent unwanted changes in the future. Fixes: #10131 "YunCore AX820: GPIO LED not correct" Reviewed-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* kernel: bump 5.10 to 5.10.127John Audia2022-07-018-18/+18
| | | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 433dc5892a60003753655aac6e6a4b59fb13b2e4)
* qoriq: enable Book-E Watchdog TimerStijn Tintel2022-07-011-0/+2
| | | | | | | | | | | | | | | | Enable PowerPC Book-E Watchdog Timer support. Having this enabled in-kernel will result in procd starting it during boot. This effectively solves the problem of the WDT in the Winbond W83793 chip potentially resetting the system during sysupgrade, which could result in an unbootable device. While the driver is modular, resulting in procd not starting the WDT during boot (because that happens before kmod load), the WDT handover during sysupgrade results in the WDT being started. This normally shouldn't be a problem, but the W83793 WDT does not like procd's defaults, nor the handover happening during sysupgrade. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit 04071cb111f290417074de130d34ae5895fd3a7b)
* ipq40xx: cut ath10k board file for mikrotik subtargetJohn Thomson2022-07-013-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Avoid shipping ath10k board file in Mikrotik initram images Most will only ever need to use these initram images once—to initially load OpenWrt, but fix these images for more consistent Wi-Fi performance between the initram and installed squashfs images. OpenWrt BUILDBOT config ignores -cut packages in the initram images build. This results in BUILDBOT initram images including the linux-firmware qca4019 board-2.bin, and (initram image booted) Mikrotik devices loading a generic BDF, rather than the intended BDF data loaded from NOR as an api 1 board_file. buildbot snapshot booted as initram image: cat /etc/openwrt_version r19679-810eac8c7f dmesg | grep ath10k | grep -E board\|BDF [ 9.794556] ath10k_ahb a000000.wifi: Loading BDF type 0 [ 9.807192] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:16 crc32 11892f9b [ 12.457105] ath10k_ahb a800000.wifi: Loading BDF type 0 [ 12.464945] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:17 crc32 11892f9b CC: Robert Marko <robimarko@gmail.com> Fixes: 5eee67a72fed ("ipq40xx: mikrotik: dont include ath10k-board-qca4019 by default") Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> Reviewed-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit 602b5f6c60a2827bd918dfae0ffb271f8b88f4df) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ipq40xx: mikrotik: dont include ath10k-board-qca4019 by defaultRobert Marko2022-07-011-0/+1
| | | | | | | | | | | | | Since MikroTik subtarget now uses dynamic BDF loading its crucial that it doesnt include the board-2.bin at all which is provided by the ath10k-board-qca4019 package. So to resolve this dont include the ath10k-board-qca4019 package on the MikroTik subtarget. Signed-off-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit 5eee67a72fed52ac686dd467d93eea95d44c8dff) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ipq-wifi: remove packaged BDF-s for MikroTik devicesRobert Marko2022-07-011-6/+4
| | | | | | | | | | | | | Since we now provide the BDF-s for MikroTik IPQ40xx devices on the fly, there is noneed to include package and ship them like we do now. This also resolves the performance issues that happen as MikroTik changes the boards and ships them under the same revision but they actually ship with and require a different BDF. Signed-off-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit ab141a6e2cb645ff64adb107af2e8973a720c1c7) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ipq40xx: mikrotik: provide BDF-s on demandRobert Marko2022-07-011-0/+23
| | | | | | | | | | | | | Since we now can pass the API 1 BDF-s aka board.bin to the ath10k driver per radio lets use that to provide the BDF-s for MikroTik devices. This also resolves the performance issues that happen as MikroTik changes the boards and ships them under the same revision but they actually ship with and require a different BDF. Signed-off-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit 4d4462cc2ace4b044e99e9b22a24cb4d89c7db95) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* qoriq: enable HARDENED_USERCOPYStijn Tintel2022-07-011-1/+0
| | | | | | | | The random crashes observed with HARDENED_USERCOPY enabled no longer seem to occur. Enable HARDENED_USERCOPY to improve security. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit 61587c92425ecdcabb82a6c81cff698a23ffb049)
* qoriq: disable CONFIG_COMPATStijn Tintel2022-07-011-8/+0
| | | | | | | | We do not need support for 32 bit applications, as we're building everything for 64 bit. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit 3e1848ee0ff3b01461a9d2f772bde27a4101f3d9)
* qoriq: 02_network fix sweth globbing logicThibaut VARÈNE2022-07-011-1/+1
| | | | | | | This prevents invalid configuration of non-existent sweth devices. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit 5fdbae463c57fa48709d876abaadbbbd5938f84f)
* qoriq: define reset button for Firebox M300Thibaut VARÈNE2022-07-012-1/+13
| | | | | | | This patch provides support for the Firebox M300 reset button. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit 19231cf83835db563ee7431b502fe1695ef1f559)
* qoriq: define leds for Firebox M300Thibaut VARÈNE2022-07-012-1/+22
| | | | | | | | | This patch provides support for the Firebox M300 only user-controllable bi-color LED, and makes the green "shield" LED act as the typical OpenWrt status led. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit 4ab421b81d383c127135716f56a1e18337575516)
* ath79: add support for RouterBOARD mAPThibaut VARÈNE2022-06-305-0/+134
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik mAP-2nd (sold as mAP) is an indoor 2.4Ghz AP with 802.3af/at PoE input and passive PoE passthrough. See https://mikrotik.com/product/RBmAP2nD for more details. Specifications: - SoC: QCA9533 - RAM: 64MB - Storage: 16MB NOR - Wireless: QCA9533 802.11b/g/n 2x2 - Ethernet: 2x 10/100 ports, 802.3af/at PoE in port 1, 500 mA passive PoE out on port 2 - 7 user-controllable LEDs Note: the device is a tiny AP and does not distinguish between both ethernet ports roles, so they are both assigned to lan. With the current setup, ETH1 is connected to eth1 and ETH2 is connected to eth0 via the embedded switch port 2. Flashing: TFTP boot initramfs image and then perform sysupgrade. The "ETH1" port must be used to upload the TFTP image. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Tested-By: Andrew Powers-Holmes <aholmes@omnom.net> Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit e1223dbee332b89caf71850eb909104529595c31)
* ipq40xx: mikrotik: make RouterBoot partition writeableThibaut VARÈNE2022-06-305-5/+0
| | | | | | | | | | Linux MTD requires the parent partition be writable for a child partition to be allowed write permission. In order for soft_config to be writeable (and modifiable via sysfs), the parent RouterBoot partition must be writeable Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit bb929a0f9cbabef59eaced57d5162d112640c3cd)
* ath79: mikrotik: add rw soft_config to extra devicesJohn Thomson2022-06-302-2/+0
| | | | | | | | Linux MTD requires the parent partition be writable for a child partition to be allowed write permission. Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> (cherry picked from commit 86fb287ad564e344d9630d8235104da144406d08)
* kernel: fix variable erasesize patchJohn Thomson2022-06-301-208/+64
| | | | | | | | | | Update this pending patch to remove the untested (variable eraseregions) section, alongside simplifying the patch. Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> [refresh and split out unrelated refreshes] Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry picked from commit 4f7065ed250932d6ff725ba175e734ad4c782f14)
* x86: 64: Add kmod-igc to default packagesHauke Mehrtens2022-06-291-1/+1
| | | | | | | | | This adds the igc driver for the Intel 2.5GBit Ethernet chip to the default packages. Fixes: #10064 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit aae3a8a254275f8be5c45d766ac7b5afb82a9fe6)
* kernel: add missing symbol to 5.10 configStijn Tintel2022-06-291-0/+1
| | | | | | | | | Kernel 5.10.124 introduced a new symbol 'LIB_MEMNEQ'. Add it to the generic 5.10 config. Fixes: 9e5d743422ed ("kernel: bump 5.10 to 5.10.124") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit f3caba679b812bdaa374929350548025e792eeec)
* qoriq: use FIT uImage for Firebox M300 kernelStijn Tintel2022-06-291-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This requires U-Boot environment changes: setenv OpenWrt_kernel watchguard_firebox-m300-fit-uImage.itb setenv loadaddr 0x20000000 setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; mmc dev 0; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr' Trying to sysupgrade an image containing this change on an M300 already running OpenWrt will fail with the following error: Tue Jun 14 12:06:21 EEST 2022 upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n). Tue Jun 14 12:06:21 EEST 2022 upgrade: Kernel switched to FIT uImage. Update U-Boot environment. Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from bootdisk... Tue Jun 14 12:06:21 EEST 2022 upgrade: Extract boot sector from the image Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from image... Image check failed. This is to prevent rendering your device unbootable. Make the U-Boot environment changes as instruced above, and then flash the image using sysupgrade -F. The config can be kept, there is no need to use -n. After the new image booted successfully, you can increase the compat_version: uci set system.@system[0].compat_version='1.1' uci commit Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit c4b499bc03ab0e2eea643c46d1d781ab64e78931)
* qoriq: use KERNEL_SUFFIX in Build/sdcard-imgStijn Tintel2022-06-291-1/+1
| | | | | | | | | | Use the KERNEL_SUFFIX variable in Build/sdcard-img, rather than using hardcoded "-kernel.bin", to allow overriding KERNEL_SUFFIX for a device. Fixes: 080a769b4da8 ("qoriq: new target") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit 86948716dbc1c220d4be504cfe5433bfd9e1d630)
* kernel: bump 5.10 to 5.10.125John Audia2022-06-273-3/+3
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 53d99fedc7afd96adfb6f38fc939c9ee9981c2ed)
* kernel: bump 5.10 to 5.10.124John Audia2022-06-2727-91/+91
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 9e5d743422edc4036cda7d96b96ba62705f382de)
* kernel: bump 5.10 to 5.10.122John Audia2022-06-2721-56/+56
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 9edc514e3dafcc36db69046a37daab818cfc1a07)
* kernel: bump 5.10 to 5.10.121John Audia2022-06-2734-62/+62
| | | | | | | | | | | | | Manually rebased: oxnas/patches-5.10/100-oxnas-clk-plla-pllb.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Signed-off-by: John Audia <therealgraysky@proton.me> (cherry picked from commit 706a4ec40cce108f484b40805bfa48619a0a7f09)
* x86: fix damaged config 5.10 refreshChristian Lamparter2022-06-272-3/+3
| | | | | | | | | | | | | Restore CONFIG_I8K + CONFIG_INTEL_INT0002_VGPIO that got removed when I refreshed the config. Each x86 target gets its own CONFIG_CRYPTO_BLAKE2S + LIB settings as only the x86_64 can use the accelerated x86 version. Also remove two extra spaces that sneaked into geode's config. Fixes: 539e60539a2f ("generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]") Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 9fc2d58bf8b37f80e8027dc55b6007e0bfa66ebe)
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-2755-2/+107
| | | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 539e60539a2fde6531bd179c94bb9c7f8f490f2b)
* mediatek: UniFi 6 LR: disable RTCDaniel Golle2022-06-271-0/+6
| | | | | | | | | There is not RTC battery connected to the SoC of the UniFi 6 LR board. Disable the RTC to prevent the system coming up with time set to 2000-01-01 00:00:00 after each reboot. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 692d87a27b44ac73c10cd511c00ee0bec1316d9f)
* ramips: decrease SPI frequency for Phicomm K2PAviana Cruz2022-06-271-2/+1
| | | | | | | | | | | Some K2P comes with the worse boards with GD25Q128 (may be A2), which only works with 50MHz frequency and less. Reduce spi frequency so that these routers can boot. remove m25p,fast-read because it isn't needed for 50MHz SPI. Signed-off-by: Aviana Cruz <gwencroft@proton.me> Signed-off-by: Chuanhong Guo <gch981213@gmail.com> (cherry picked from commit 857ea3f690aba8513b356926d9c430adafc7c50b)
* apm821xx: WNDAP660: fix ethernet port orderingChristian Lamparter2022-06-254-13/+13
| | | | | | | | | | | | | | | | | | | Tim Small reported: | Viewing the 'Network' -> 'Switch' config page in LuCI: | | The LuCI LAN 1 port corresponds to the port physically | labelled 2 at the rear of the device. | [...] | | When a patch cord is attached to the port labelled 1 [...], | the LED labelled °2 illuminates. => essentially, the Ports and LEDs are reversed. Reported-by: Tim Small Fixes: #10111 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 36483600d337ab3ec8a6dabeaa160614d07f5588)
* ramips: mt7621-dts: fix claiming rgmii2 pin group for EdgeRouter X SFPArınç ÜNAL2022-06-252-5/+7
| | | | | | | | | | | | | | | | | | | | For a TX->TX connected external phy to transmit/receive data, the rgmii2 pin group needs to be claimed with gpio function, at least for EdgeRouter X SFP. We already claim the pin group under the pinctrl node with gpio function on the gpio node on mt7621_ubnt_edgerouter-x.dtsi. However, we should claim a pin group under its consumer node. It's the ethernet node in this case, which we already claim the rgmii2 pin group under it on mt7621.dtsi. Therefore, set the function as gpio on the rgmii2 node for EdgeRouter X SFP and get rid of claiming the rgmii2 pin group under the pinctrl node. With this change, we also get to remove a definition from mt7621_ubnt_edgerouter-x.dtsi which is specific to EdgeRouter X SFP. This change is tested on an EdgeRouter X SFP. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> (cherry picked from commit a1ad8377355c41a7cc3012b707fcecab923cbc90)
* ramips: force ZyXEL NR7101 to boot from "Kernel" partitionBjørn Mork2022-06-251-0/+1
| | | | | | | | | | | | | | | | | | | | Make sure BootingFlag points to the system partition we install to. The BootingFlag variable selects which system partition the system boots from (0 => "Kernel", 1 => "Kernel2"). OpenWrt does not yet have device specific support for this dual image scheme, and can therefore only boot from "Kernel". This has not been an issue until now, since all known OEM firmware versions have ignored "Kernel2" - leaving the BootingFlag fixed at 0. But the newest OEM firmware has a new upgrade procedure, installing to the "inactive" system partition and setting BootingFlag accordingly. This workaround is needed until the dual image scheme is fully supported. Signed-off-by: Bjørn Mork <bjorn@mork.no> (cherry picked from commit 79112e7d4758cc79dea506ffebdf40e00d94fa06)
* ath79: fix rootfs padding for D-Link DAP-2xxxSebastian Schaper2022-06-251-1/+2
| | | | | | | | | | | | It was observed that `rootfs_data` was sometimes not correctly erased after performing sysupgrade, resulting in previous settings to prevail. Add call to `wrgg-pad-rootfs` in sysupgrade image recipe to ensure any previous jffs2 will be wiped, consistent with DAP-2610 from the ipq40xx target, which introduced the double-flashing procedure for these devices. Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net> (cherry picked from commit f770c33d7bb94b610d3a1c1fa84bc917678b65bc)
* mpc85xx: p2020: add RTC ds1307 to kernelJosef Schlehofer2022-06-251-0/+1
| | | | | | | | | | | | | | | If the RTC module is compiled as a module, the hctosys fails to initialize because ds1307 is loaded later. Fixes: [ 2.004145] hctosys: unable to open rtc device (rtc0) [ 11.957997] rtc-ds1307 0-006f: registered as rtc0 This is similar to commit 5481ce9a1157a43d8b2c963e03fb243e70974361, which was done for imx6 target. Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (cherry picked from commit dc7f78da97c62cd6c17a75f754da5bf6b957837d)
* bcm53xx: remove 07_set_preinit_iface_bcm53xxChristian Lamparter2022-06-251-14/+0
| | | | | | | | | with the switch to DSA setup, the switch gets correctly programmed via the device-tree now. This hack is no longer necessary. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 554ca44730731da6fddc51e1d3027c5e666a7d0d)
* realtek: make "u-boot-env" partition writable for Netgear 3xx seriesAndreas Böhler2022-06-241-1/+0
| | | | | | | | | | The Netgear GS3xx devices do not properly initialise the port LEDs during startup unless the boot command in U-Boot is changed. Making the U-Boot env partition writable allows this modification to be done from within OpenWrt by calling "fw_setenv bootcmd rtk network on\; boota". Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit d9e12c21fa98c90d0cc355e344d90469c5fd42c1)
* realtek: make Netgear GS1xx u-boot env partition writableStijn Segers2022-06-241-1/+0
| | | | | | | | | | | | Make the u-boot environment partition for the NETGEAR GS108T v3 and GS110TPP writable (they share a DTS), so the values can be manipulated from userspace. See https://forum.openwrt.org/t/57875/1567 for a real world example. Signed-off-by: Stijn Segers <foss@volatilesystems.org> (cherry picked from commit 9c381d3386ab375a4c79812641192faef368d191)
* ramips: fix booting on ZyXEL NBG-419N v2Piotr Dymacz2022-06-201-0/+1
| | | | | | | | | | | | | | This fixes a well known "LZMA ERROR 1" error, reported previously on numerous of other devices from 'ramips' target. Fixes: #9842 Fixes: #8964 Reported-by: Juergen Hench <jurgen.hench@gmail.com> Tested-by: Juergen Hench <jurgen.hench@gmail.com> Signed-off-by: Demetris Ierokipides <ierokipides.dem@gmail.com> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> (cherry picked from commit fd72e595c2b2a46bab8cbc7e9415fbfeae7b5b0d)
* realtek: add support for power LED on Netgear GS108Tv3Pascal Ernster2022-06-191-0/+27
| | | | | | | | | | | | | | | | | | | | | | The Netgear GS108Tv3 is already supported by OpenWrt, but is missing LED support. After OpenWrt installation, all LEDs are off which makes the installation quite confusing. This enables support for the green/amber power LED to give feedback about the current status. This is basically just a verbatim copy of commit c4927747d25a ("realtek: add support for power LED on Netgear GS308Tv1"). Please note that both LEDs are wired up in an anti-parallel fashion, which means that only one of both LEDs/colors can be switched on at the same time. If both LEDs/colors are switched on simultanously, the LED goes dark. Tested-by: Pascal Ernster <git@hardfalcon.net> Signed-off-by: Pascal Ernster <git@hardfalcon.net> [add title to commit reference] Signed-off-by: Sander Vanheule <sander@svanheule.net> (cherry picked from commit adbdfc9366fed2d28dbd36883ddbdb566a313f71)
* realtek: add support for power LED on Netgear GS308Tv1Andreas Böhler2022-06-191-0/+27
| | | | | | | | | | | The Netgear GS308Tv1 is already supported by OpenWrt, but is missing LED support. After OpenWrt installation, all LEDs are off which makes the installation quite confusing. This enables support for the green/amber power LED to give feedback about the current status. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit c4927747d25af59db8233a66a59fdf9e8c0e395d)
* ramips: fix RT-AC57U button levelDavid Bauer2022-06-181-1/+1
| | | | | | | | Both buttons on the RT-AC57U are active-low. Fix the GPIO flag for the WPS cutton to fix button behavior. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 535b0c70b1c466733b009144f81f5207f1ecd311)
* mpc85xx: enable error reporting for RAM and PCIeJosef Schlehofer2022-06-141-0/+4
| | | | | | | | | | | | | | | | | | | | | All Freescale processors used in this target are capable to detect error and correction. [1] It can not be used as kernel module. [2] This is helpful to report hardware errors. It enables three kernel options: - EDAC, which is a subsystem - EDAC_LEGACY_SYSFS, it enables sysfq nodes - MP85XX, support for Freescale MPC8349, MPC8560, MPC8540, MPC8548, T4240 EDAC is already enabled for following targets: qoriq, octeon, octeontx and zynq. [1] https://cateee.net/lkddb/web-lkddb/EDAC.html [2] https://patchwork.ozlabs.org/patch/554908/ Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> (cherry picked from commit bfc73f42df3189a2eb34bebc8d9e73b3389a83a2)
* sunxi/cortexa53: enable armv8-CE crypto algorithmsEneas U de Queiroz2022-06-111-0/+10
| | | | | | | | This enables armv8 crypto extensions version of AES, GHASH, SHA1, and CRC T10 algorithms in the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit 9be35180f43a4916f53430d8c93437d33896e860)
* rockchip/armv8: enable armv8-CE crypto algorithmsEneas U de Queiroz2022-06-111-0/+9
| | | | | | | | This enables armv8 crypto extensions version of AES, GHASH, and CRC T10 algorithms in the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit b1346d35e470662c98912efc49108733ee7c101c)
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-01 15:58:02 +0000