aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for Netgear WN3000RPv3Rodolphe de Saint Léger2022-03-166-155/+186
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3100RPv2 http://www.netgear.com/support/product/wn3100rpv2.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This device seems to be same hardware as a WN3000RPv3 Flash instructions: - Use the Netgear WebUI to upgrade to OpenWRT using the factory image (see note below), - Use the sysupgrade image for upgrading versions from OpenWRT, - TFTP recovery procedure can be used to flash the factory image (preferred method). Note: - The WebUI may not reboot automatically, wait at least 5 minutes before powercycling the device Flashing using TFTP: - Set you IP address to 192.168.1.10/24 (no gateway) - Connect your machine to the Ethernet port - Power off the device and wait for 10 seconds, - Hold the reset button and power on the device (do not release reset), - Hold the reset button until the green light is flashing (Approx. 15s) - launch tftp, set mode to binary and connect to 192.168.1.1 - put the factory firmware image - All leds will switch off (like a power off), this is normal - Wait for the device to reboot in the new OpenWRT image (max 5 mins) - The first boot will take longer than usual. - After boot, the Device IP on the ethernet port is 192.168.1.1 Signed-off-by: Rodolphe de Saint Léger <rdesaintleger@gmail.com> [drop unneeded includes in dts, wrap commit message] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7620: Add support for D-Link DWR-961 A1Pawel Dembicki2022-03-168-172/+273
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DWR-961 A1 Wireless Router is based on the MT7620A SoC. It's a merge of two Amit boards: DWR-960 with ethernet part of Lava LR-25G001. ROMID it's taken from Telenor branded version and it works with tested device. Images from D-Link site for this router are from DWR-953 and it have ROMID DLK6E2424001. I don't know if it's mistake on web-site or if it's will require different image. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612 mpcie card) - 5x 10/100/1000 Mbps Ethernet: 4xLAN and 1xWAN (QCA8337) - 2x internal, non-detachable antennas (Wifi 2.4G) - 3x external, detachable antennas (2x LTE, 1x Wifi 5G) - 1x LTE modem cat 6 - UART (J5) header on PCB (57600 8n1) - 13x LED, 2x button - JBOOT bootloader Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* qoriq: enable I2C in target kernel configStijn Tintel2022-03-161-0/+3
| | | | | | | | | | | The I2C controller used in QorIQ PPC devices requires the mpc-i2c driver, which is enabled by the I2C_MPC kernel config symbol. Enable this and its dependencies in the target kernel config, as is done for the mpc85xx target. This fixes missing hwmon, rtc and tpm devices on the M300. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* bcm4908: include U-Boot DTB files for ASUS GT-AX6000 & Netgear RAX220Rafał Miłecki2022-03-151-0/+34
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: include CONFIG_KEXEC_SIG in configsPhilip Prindeville2022-03-153-1/+2
| | | | | | | | | | | | | | Seeing failure to build because of missing symbols related to provisioning CONFIG_KEXEC and signed images. Without this, if you set CONFIG_KERNEL_KEXEC=y and try to build, target/linux will hang at: scripts/kconfig/conf --syncconfig Kconfig ... kexec system call (KEXEC) [Y/n/?] y kexec file based system call (KEXEC_FILE) [Y/n/?] y Verify kernel signature during kexec_file_load() syscall (KEXEC_SIG) [N/y/?] (NEW) Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
* kernel: backport DSA patches fixing null-pointer dereference for 5.10Marek Behún2022-03-152-0/+151
| | | | | | | | | Backport patches 381a730182f1 ("net: dsa: Move VLAN filtering syncing out of dsa_switch_bridge_leave") 108dc8741c20 ("net: dsa: Avoid cross-chip syncing of VLAN filtering") from upstream (currently in net-next) to fix null-pointer dereference. Signed-off-by: Marek Behún <kabel@kernel.org>
* ath79: add support for Araknis AN-700-AP-I-ACMichael Pratt2022-03-135-0/+119
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: 2AG6R-AN700APIAC Araknis AN-700-AP-I-AC is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP1750 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3 - QCA9880 WLAN PCI card, 5 GHz, 3x3, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state **MAC addresses:** MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH *:xb art 0x0 phy1 2.4G *:xc --- phy0 5GHz *:xd --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Araknis AN-500-AP-I-ACMichael Pratt2022-03-135-0/+120
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: 2AG6R-AN500APIAC Araknis AN-500-AP-I-AC is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EAP1200 the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - QCA9557 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - QCA9882 WLAN PCI card 168c:003c, 5 GHz, 2x2, 26dBm - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM NT5TU32M16 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state **MAC addresses:** MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH *:e1 art 0x0 phy1 2.4G *:e2 --- phy0 5GHz *:e3 --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: add support for Araknis AN-300-AP-I-NMichael Pratt2022-03-135-0/+134
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FCC ID: U2M-AN300APIN Araknis AN-300-AP-I-N is an indoor wireless access point with 1 Gb ethernet port, dual-band wireless, internal antenna plates, and 802.3at PoE+ this board is a Senao device: the hardware is equivalent to EnGenius EWS310AP the software is modified Senao SDK which is based on openwrt and uboot including image checksum verification at boot time, and a failsafe image that boots if checksum fails **Specification:** - AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2 - AR9382 WLAN PCI on-board 168c:0030, 5 GHz, 2x2 - AR8035-A PHY RGMII GbE with PoE+ IN - 40 MHz clock - 16 MB FLASH MX25L12845EMI-10G - 2x 64 MB RAM 1839ZFG V59C1512164QFJ25 - UART console J10, populated, RX shorted to ground - 4 antennas 5 dBi, internal omni-directional plates - 4 LEDs power, 2G, 5G, wps - 1 button reset NOTE: all 4 gpio controlled LEDS are viewed through the same lightguide therefore, the power LED is off for default state **MAC addresses:** MAC address labeled as ETH Only one Vendor MAC address in flash at art 0x0 eth0 ETH *:7d art 0x0 phy1 2.4G *:7e --- phy0 5GHz *:7f --- **Serial Access:** the RX line on the board for UART is shorted to ground by resistor R176 therefore it must be removed to use the console but it is not necessary to remove to view boot log optionally, R175 can be replaced with a solder bridge short the resistors R175 and R176 are next to the UART RX pin at J10 **Installation:** Method 1: Firmware upgrade page: (if you cannot access the APs webpage) factory reset with the reset button connect ethernet to a computer OEM webpage at 192.168.20.253 username and password 'araknis' make a new password, login again... Navigate to 'File Management' page from left pane Click Browse and select the factory.bin image Upload and verify checksum Click Continue to confirm wait about 3 minutes Method 2: Serial to load Failsafe webpage: After connecting to serial console and rebooting... Interrupt uboot with any key pressed rapidly execute `run failsafe_boot` OR `bootm 0x9fd70000` wait a minute connect to ethernet and navigate to 192.168.20.253 Select the factory.bin image and upload wait about 3 minutes **Return to OEM:** Method 1: Serial to load Failsafe webpage (above) Method 2: delete a checksum from uboot-env this will make uboot load the failsafe image at next boot because it will fail the checksum verification of the image ssh into openwrt and run `fw_setenv rootfs_checksum 0` reboot, wait a minute connect to ethernet and navigate to 192.168.20.253 select OEM firmware image and click upgrade Method 3: backup mtd partitions before upgrade **TFTP recovery:** Requires serial console, reset button does nothing rename initramfs-kernel.bin to '0101A8C0.img' make available on TFTP server at 192.168.1.101 power board, interrupt boot with serial console execute `tftpboot` and `bootm 0x81000000` NOTE: TFTP may not be reliable due to bugged bootloader set MTU to 600 and try many times **Format of OEM firmware image:** The OEM software is built using SDKs from Senao which is based on a heavily modified version of Openwrt Kamikaze or Altitude Adjustment. One of the many modifications is sysupgrade being performed by a custom script. Images are verified through successful unpackaging, correct filenames and size requirements for both kernel and rootfs files, and that they start with the correct magic numbers (first 2 bytes) for the respective headers. Newer Senao software requires more checks but their script includes a way to skip them. The OEM upgrade script is at /etc/fwupgrade.sh OKLI kernel loader is required because the OEM software expects the kernel to be less than 1536k and the OEM upgrade procedure would otherwise overwrite part of the kernel when writing rootfs. Note on PLL-data cells: The default PLL register values will not work because of the external AR8035 switch between the SOC and the ethernet port. For QCA955x series, the PLL registers for eth0 and eth1 can be see in the DTSI as 0x28 and 0x48 respectively. Therefore the PLL registers can be read from uboot for each link speed after attempting tftpboot or another network action using that link speed with `md 0x18050028 1` and `md 0x18050048 1`. The clock delay required for RGMII can be applied at the PHY side, using the at803x driver `phy-mode` setting through the DTS. Therefore, the Ethernet Configuration registers for GMAC0 do not need the bits for RGMII delay on the MAC side. This is possible due to fixes in at803x driver since Linux 5.1 and 5.3 Signed-off-by: Michael Pratt <mcpratt@pm.me>
* ath79: improve factory.bin for some Senao devicesMichael Pratt2022-03-131-1/+3
| | | | | | | | | | | | | | | | | | | | | | | Some boards with firmware made with Senao SDK based on Linux 3.3 have the following lines in the OEM upgrade script at /etc/fwupgrade.sh local append="" local CONF_TAR="/tmp/sysupgrade.tgz" [ -f "$CONF_TAR" ] && append="-j $CONF_TAR" and \# check FWINFO filename [ -z $(ls FWINFO* | grep -i ${modelname}) ] && errcode="1" This addition also prevents needing to factory reset after flashing for some boards that also have these lines in the script \# Support downgrade but do default (Smart v2.x.x.x -> senaowrt v1.x.x.x) [ $(ls FWINFO* | grep -i ${modelname} | cut -d "-" -f4 | cut -c 2) -lt 2 ] && append="" Signed-off-by: Michael Pratt <mcpratt@pm.me>
* realtek: add support for Panasonic Switch-M8eG PN28080KINAGAKI Hiroshi2022-03-133-0/+338
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Panasonic Switch-M8eG PN28080K is a 8 + 1 port gigabit switch, based on RTL8380M. Specification: - SoC : Realtek RTL8380M - RAM : DDR3 128 MiB (Winbond W631GG8KB-15) - Flash : SPI-NOR 32 MiB (Macronix MX25L25635FMI-10G) - Ethernet : 10/100/1000 Mbps x8 + 1 - port 1-8 : TP, RTL8218B (SoC) - port 9 : SFP, RTL8380M (SoC) - LEDs/Keys : 7x / 1x - UART : RS-232 port on the front panel (connector: RJ-45) - 3:TX, 4:GND, 5:GND, 6:RX (pin number: RJ-45) - 9600n8 - Power : 100-240 VAC, 50/60 Hz, 0.5 A - Plug : IEC 60320-C13 - Stock OS : VxWorks based Flash instruction using initramfs image: 1. Prepare the TFTP server with the IP address 192.168.1.111 2. Rename the OpenWrt initramfs image to "0101A8C0.img" and place it to the TFTP directory 3. Download the official upgrading firmware (ex: pn28080k_v30000.rom) and place it to the TFTP directory 4. Boot M8eG and interrupt the U-Boot with Ctrl + C keys 5. Execute the following commands and boot with the OpenWrt initramfs image rtk network on tftpboot 0x81000000 bootm 6. Backup mtdblock files to the computer by scp or anything and reboot 7. Interrupt the U-Boot and execute the following commands to re-create filesystem in the flash ffsmount c:/ ffsfmt c:/ this step takes a long time, about ~ 4 mins 8. Execute the following commands to put the official images to the filesystem updatert <official image> example: updatert pn28080k_v30000.rom this step takes about ~ 40 secs 9. Set the environment variables of the U-Boot by the following commands setenv loadaddr 0xb4e00000 setenv bootcmd bootm saveenv 10: Download the OpenWrt initramfs image and boot with it tftpboot 0x81000000 0101A8C0.img bootm 11: On the initramfs image, download the sysupgrade image and perform sysupgrade with it sysupgrade <imagename> 12: Wait ~ 120 seconds to complete flashing Note: - "Switch-M8eG" is a model name, and "PN28080K" is a model number. Switch-M8eG has an another (old) model number ("PN28080"), it's not a Realtek based hardware. - Switch-M8eG has a "POWER" LED (Green), but it's not connected to any GPIO pin. - The U-Boot checks the runtime images in the flash when booting and fails to execute anything in "bootcmd" variable if the images are not exsisting. - A filesystem is formed in the flash (0x100000-0x1DFFFFF) on the stock firmware and it includes the stock images, configuration files and checksum files. It's unknown format, can't be managed on the OpenWrt. To get the enough space for OpenWrt, move the filesystem to the head of "fs_reserved" partition by execution of "ffsfmt" and "updatert". - On the other devices in the same series of Switch-M8eG PN28080K, the INT pin on the PCA9555 is not connected to anywhere. Back to the stock firmware: 1. Delete "loadaddr" variable and set "bootcmd" to the original value on U-Boot: setenv loadaddr setenv bootcmd 'bootm 0x81000000' on OpenWrt: fw_setenv loadaddr fw_setenv bootcmd 'bootm 0x81000000' 2. Perform reset or reboot on U-Boot: reset on OpenWrt: reboot Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Reviewed-by: Sander Vanheule <sander@svanheule.net>
* realtek: enable pca953x driver for rtl838x subtargetINAGAKI Hiroshi2022-03-131-0/+3
| | | | | | | | | | The system status LED on Panasonic Switch-M8eG PN28080K is connected to a PCA9539PW. To use the LED as a status LED of OpenWrt while booting, enable the pca953x driver and built-in to the kernel. Also enable CONFIG_GPIO_PCA953X_IRQ to use interrupt via RTL83xx GPIO. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Acked-by: Sander Vanheule <sander@svanheule.net>
* realtek: add ZyXEL GS1900-24 v1 supportMartin Kennedy2022-03-132-0/+137
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL GS1900-24 v1 is a 24 port switch with two SFP ports, similar to the other GS1900 switches. Specifications -------------- * Device: ZyXEL GS1900-24 v1 * SoC: Realtek RTL8382M 500 MHz MIPS 4KEc * Flash: 16 MiB * RAM: Winbond W9751G8KB-25 64 MiB DDR2 SDRAM * Ethernet: 24x 10/100/1000 Mbps, 2x SFP 100/1000 Mbps * LEDs: * 1 PWR LED (green, not configurable) * 1 SYS LED (green, configurable) * 24 ethernet port link/activity LEDs (green, SoC controlled) * 2 SFP status/activity LEDs (green, SoC controlled) * Buttons: * 1 "RESET" button on front panel (soft reset) * 1 button ('SW1') behind right hex grate (hardwired power-off) * Power: 120-240V AC C13 * UART: Internal populated 10-pin header ('J5') providing RS232; connected to SoC UART through a SIPEX 3232EC for voltage level shifting. * 'J5' RS232 Pinout (dot as pin 1): 2) SoC RXD 3) GND 10) SoC TXD Serial connection parameters: 115200 8N1. Installation ------------ OEM upgrade method: * Log in to OEM management web interface * Navigate to Maintenance > Firmware > Management * If "Active Image" has the first option selected, OpenWrt will need to be flashed to the "Active" partition. If the second option is selected, OpenWrt will need to be flashed to the "Backup" partition. * Navigate to Maintenance > Firmware > Upload * Upload the openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin file by your preferred method to the previously determined partition. When prompted, select to boot from the newly flashed image, and reboot the switch. * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin U-Boot TFTP method: * Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10). * Set up a TFTP server on your client and make it serve the initramfs image. * Connect serial, power up the switch, interrupt U-boot by hitting the space bar, and enable the network: > rtk network on > Since the GS1900-24 v1 is a dual-partition device, you want to keep the OEM firmware on the backup partition for the time being. OpenWrt can only be installed in the first partition anyway (hardcoded in the DTS). To ensure we are set to boot from the first partition, issue the following commands: > setsys bootpartition 0 > savesys * Download the image onto the device and boot from it: > tftpboot 0x81f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-initramfs-kernel.bin > bootm * Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it: > sysupgrade /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24-v1-squashfs-sysupgrade.bin Signed-off-by: Martin Kennedy <hurricos@gmail.com>
* kernel: bump 5.10 to 5.10.104John Audia2022-03-133-12/+12
| | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* ramips: Apply pinctrl DTS changes to TL-WPA8631PJoe Mullally2022-03-131-9/+13
| | | | | | | | | Applies changes from 7774b86019 to new device committed later. Fix some whitespace in the DTS. Use standard model name format in DTS. Fixes: 6c743c3006f9 ("ramips: Add support for TP-Link TL-WPA8631P v3") Signed-off-by: Joe Mullally <jwmullally@gmail.com> Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
* ath79: Add LED labels for Airtight C-75Sven Schwermer2022-03-131-0/+2
| | | | | | | | | Keep labels since OpenWrt userland tooling (get_dt_led) depends on them to find the LED instances referenced by the led-* aliases. The label for the amber power LED was removed in 4eefdc7adb. Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
* ramips: update WLAN MAC address of JCG Y2Chukun Pan2022-03-131-0/+4
| | | | | | | | MAC addresses on OEM firmware: 04:xx:xx:xx:xx:c8 factory 0x4 wlan2g 06:xx:xx:xx:xx:c8 [not on flash] wlan5g Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: update WLAN MAC address of Phicomm K2PChukun Pan2022-03-132-2/+13
| | | | | | | The wireless mac address difference of this machine is similar to that of D-Link DIR-853-R1, so use the same practice. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ramips: Add support for Dual-Q H721Dawsen Gao2022-03-132-0/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Dual-Q H721 is a router platform board, it is the smaller model of the U7621-06. The device has the following specifications: MT7621AT (880 MHz) 256 of RAM (DDR3) 16 MB of FLASH (MX25l12805d SPI) 5x 1 Gbps Ethernet (MT7621 built-in switch) 1x M.2 (NGFF) 3.7V 3A max for 5G M.2 Modem work at USB3.0 mode 1x Minipcie 3.7V 3A max for LTE Modem work at USB2.0 Mode 2x Minipcie for WIFI card 4x Lan+1x Wan 10/100M/1000M RJ45 port 14x LEDs (1x GPIO-controlled) 1x reset button 1x UART header (4-pins) 1x mico SD-card reader 1x DC jack for main power (5~27 V) The following has been tested and is working: Ethernet switch miniPCIe slots (tested with Wi-Fi cards and LTE modem cards) miniSIM slot (works with normal size simcard) sysupgrade reset button micro SD-card reader Installation: This board has no locked down bootloader. The seller can be asked to install openwrt, so upgrades are standard sysupgrade method. Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. Signed-off-by: Dawsen Gao <dawsen_gao@163.com> [change author name (used SoB one), add ethernet pinctrl, apply sorting to device recipe] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* bcm4908: include U-Boot in imagesRafał Miłecki2022-03-111-3/+32
| | | | | | This is a step forward in adding support for devices with U-Boot. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* imx: fix USB supportPiotr Dymacz2022-03-111-0/+1
| | | | | | | | | | | The ChipIdea USB kernel driver gained support for disabling glue drivers in 5.8, see upstream commmit: 95caa2ae70fd ("usb: chipidea: allow disabling glue drivers if EMBEDDED"). This enables 'CONFIG_USB_CHIPIDEA_IMX' in the 'imx' target kernel config which brings back USB support. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* x86: legacy: enable pata_sis driverMatthias Schiffer2022-03-101-0/+1
| | | | | | | | This driver is needed to boot from CompactFlash on the Siemens Futro S400. The device has an AMD NX1500 CPU, which seems to be unsupported by the geode subtarget, so it must use legacy. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* kernel: wwan: add MeigLink SLM750 modem supportDaniel Golle2022-03-101-0/+33
| | | | | | | | | | Add patch found in Teltonika RUT9_R_00.07.01.4 GPL SDK download[1] adding USB IDs of the MeigLink SLM750 to the relevant kernel drivers. Newer versions of Teltonika's 2G/3G/4G RUT9XX WWAN router series come with this kind of modem. [1]: https://wiki.teltonika-networks.com/view/GPL Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: allow USB power control on TP-Link MR3020v3Dmitry Chigiryov2022-03-091-1/+12
| | | | | | | | | | | | | By switching EPHY_LED4_N_JTRST_N from EPHY_LED4_N to GPIO#39 we can control USB port power an all current revisions of MR3020v3. It was not a thing on some first revisions, pin was unused. But for now on all current MR3020v3 boards EPHY_LED4_N_JTRST_N pin is connected to USB power key. Also it was not used as EPHY indicator on any revision of the board. Signed-off-by: Dmitry Chigiryov <dmitry.chigiryov@ya.ru> [changed author address (used SoB one)] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix DEVICE_VENDOR for unbranded devicesSungbo Eo2022-03-095-9/+9
| | | | | | | | | | | | | | | In commit ee66fe4ea9a6 ("ramips: convert DEVICE_TITLE to new variables"), DEVICE_VENDOR of some unbranded devices were set incorrectly: * WR512-3GN is not a dev board from Ralink. * "XDX-RN502J" is the whole model name and should be not split. This patch sets their DEVICE_VENDOR to "Unbranded", and changes their DTS model properties accordingly. Ref: d0bf15f23595 ("ramips: add support for A5-V11 board (resubmit)") Ref: 9085b05d9e71 ("ramips: rt305x: support for wr512-3gn-like routers") Ref: 0e486d2fd297 ("ramips: add support for unbranded XDX-RN502J board") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt7621: add support for Zbtlink ZBT-WG1608Kim Namu2022-03-094-0/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1608 is a Wi-Fi router intendent to use with WWAN (4G/5G) modems. Specifications: * SoC: MediaTek MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * Wi-Fi: * MediaTek MT7603E : 2.4Ghz * MediaTek MT7613BE : 5Ghz * Ethernet: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * M.2: 1x slot with USB&SIM * EM7455/EM12-G/EM160R/RM500Q-AE * USB: 1x 3.0 Type-A port * External storage: 1x microSD (SDXC) slot * UART: console (115200 baud) * LED: * 1 power indicator * 1 WLAN 2.4G controlled (wlan 2G) * 3 SoC controlled (wlan 5G, wwan, internet) * 5 per Eth phy (4xLAN + WAN) MAC Addresses: * LAN : f8:5e:3c:xx:xx:e0 (Factory, 0xe000 (hex)) * WAN : f8:5e:3c:xx:xx:e1 (Factory, 0xe006 (hex)) * 2.4 GHz: f8:5e:3c:xx:xx:de (Factory, 0x0004 (hex)) * 5 GHz : f8:5e:3c:xx:xx:df (Factory, 0x8004 (hex)) Installation: * Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Recovery Mode: * Press reset button, power up the device, wait for about 10sec. * Upload sysupgrade image through the firmware recovery mode web page at 192.168.1.1. Signed-off-by: Kim Namu <namu@theseed.io>
* ramips: add support for Asus RT-AC1200Ray Wang2022-03-093-26/+194
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Asus RT-AC1200 is a 2.4/5GHz dual band AC router, based on MediaTek MT7628AN. Specification: * SoC: MT7628AN * RAM: DDR2 64 MiB * Flash: 16 MiB NOR (W25Q128BV) * Wi-Fi: * 2.4GHz: SoC Built-in * 5GHz: MT7612EN * Ethernet: 5x 100Mbps * Switch: SoC built-in * USB: 1x 2.0 Flash Layout: 0x0000000-0x0030000 : "bootloader" 0x0030000-0x0040000 : "nvram" 0x0040000-0x0050000 : "factory" 0x0050000-0x1000000 : "firmware" MAC address: LAN: factory 0x28 WAN: factory 0x22 2.4G: factory 0x4 5G: factory 0x8004 Installation via **recovery** mode: 1. Download the Asus recovery firmware (windows) tool from http://dlcdnet.asus.com/pub/ASUS/LiveUpdate/Release/Wireless/Rescue.zip 2. Set your ethernet IP manually 192.168.1.5 / 255.255.255.0 with NO gateway. 3. Plug in your ethernet to LAN port 1 on the router. 4. Load up the recovery software with the firmware file, but don't press "Upload" yet. 5. Plug in the router to power WHILE HOLDING the reset button in. While CONTINUING to hold the button, select "Upload" Continue to hold the reset button in until it finishes and verifies! 6. If that doesn't work try pressing "Upload" first just before you do step 5. At some point while holding reset the rescue tool will finally detect and upload the firmware. That's when you can let go of the reset button. 7. The router will reboot and not much will happen. Wait a minute or 2. 8. Power off and on the router again. Voila. Set everything your Ethernet IP back to DHCP (automatically) and you're good to go. Revert to stock firmware: 1. Install stock image via recovery mode. Tested-by: Ivan Pavlov <AuthorReflex@gmail.com> Signed-off-by: Ray Wang <raywang777@foxmail.com>
* ramips: add support for Renkforce WS-WN530HP3-ABirger Koblitz2022-03-083-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Renkforce WS-WN530HP3-A ceiling- mountable Wireless Access Point, which is powered over PoE. Hardware: - SoC: Mediatek MT7621DAT - RAM: 128MiB on SoC - Flash: 16MiB GigaDevice GD25Q128C - 2.4Ghz Wifi: Mediatek MT603EN - 5GHz Wifi: MT613BEN - Ethernet: - 1x 1GBit WAN port, passive PoE capable - 2x 1GBit LAN ports LEDs: 1x Bi-Color LED (red/blue) Buttons: 1x Reset Button, 1x Power Button Installation: Power on the access point and immedately press the reset button for 10 seconds. Connect web-browser to 192.168.10.1 and upload sysupgrade image. Flash uploaded image and wait about 2 minutes for reboot. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed SoB]
* ath79: fix button labels for WZR-HP-AG300H and WZR-600DHPJeffery To2022-03-081-0/+6
| | | | | | | | These were present in ar71xx but overlooked when porting to ath79. Fixes: 480bf2827392 ("ath79: add support for Buffalo WZR-HP-AG300H") Signed-off-by: Jeffery To <jeffery.to@gmail.com>
* ath79: add support for MikroTik RouterBOARD mAP liteThibaut VARÈNE2022-03-085-1/+81
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik RouterBOARD mAPL-2nd (sold as mAP Lite) is a small 2.4 GHz 802.11b/g/n PoE-capable AP. See https://mikrotik.com/product/RBmAPL-2nD for more info. Specifications: - SoC: Qualcomm Atheros QCA9533 - RAM: 64 MB - Storage: 16 MB NOR - Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 1.5 dBi antenna - Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 802.3af/at PoE in - 4 user-controllable LEDs: · 1x power (green) · 1x user (green) · 1x lan (green) · 1x wlan (green) Flashing: TFTP boot initramfs image and then perform sysupgrade. Follow common MikroTik procedure as in https://openwrt.org/toh/mikrotik/common. Note: following 781d4bfb397cdd12ee0151eb66c577f470e3377d The network setup avoids using the integrated switch and connects the single Ethernet port directly. This way, link speed (10/100 Mbps) is properly reported by eth0. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* ipq806x: provide ramoops for R7800/XR500 by defaultHannu Nyman2022-03-081-2/+2
| | | | | | | | | | | | | Add kmod-ramoops to the default set of device packages in R7800 and XR500, so that the ramoops kernel crash logs are provided by default for these routers. The capability was earlier defined by 97158fe1 and cf346dfa, but the feature was not yet turned on by default. The possible kernel crashes are stored into /sys/fs/pstore/* Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ath79: Add green power LED to Airtight C-75Sven Schwermer2022-03-081-7/+15
| | | | | | | In addition to the missing green LED definition, the polarity of the amber power LED was incorrect which is fixed here. Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
* lantiq: xrx200: fix use after free bugAleksander Jan Bajkowski2022-03-084-0/+30
| | | | | | | The skb->len field is read after the packet is sent to the network stack. In the meantime, skb can be freed. This patch fixes this bug. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* realtek: add support for I-O DATA BSH-G24MBINAGAKI Hiroshi2022-03-072-0/+206
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA BSH-G24MB is a 24 port gigabit switch, based on RTL8382M. Specification: - SoC : Realtek RTL8382M - RAM : DDR2 128 MiB (Nanya NT5TU128M8HE-AC) - Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G) - Ethernet : 10/100/1000 Mbps x24 - port 1-8 : RTL8218B - port 9-16 : RTL8218B (SoC) - port 17-24 : RTL8218B - LEDs/Keys : 2x, 1x - UART : pin header on PCB - JP2: 3.3V, TX, RX, GND from rear side - 115200n8 - Power : 100 VAC, 50/60 Hz - Plug : IEC 60320-C13 Flash instruction using sysupgrade image: 1. Boot BSH-G24MB normally 2. Connect BSH-G24MB to the DHCP enabled network 3. Find the device's IP address and open the WebUI and login Note: by default, the device obtains IP address from DHCP server of the network 4. Open firmware update page ("ファームウェア アップデート") 5. Rename the OpenWrt sysupgrade image to "bsh-g24mb_v100.image" and select it 6. Press apply ("適用") button to perform update 7. Wait ~150 seconds to complete flashing Note: - BSH-G24MB has a power-related LED ("電源"), but it's not connected to the GPIO of the SoC or RTL8231 and cannot be controlled. Instead of it, use system status LED on other than running-state. - "sys_loop" LED indicates system status and loop-detection status in stock firmware. - BSH-G24MB has 2x os-image partitions named as "RUNTIME"/"RUNTIME2" in 16 MiB SPI-NOR flash and the size of image per partition is only 6848 KiB. The secondary image is never used on stock firmware, so also use it on OpenWrt to get more space. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* bcm4908: fix init on CFE devicesRafał Miłecki2022-03-071-1/+1
| | | | | | | exit in preinit script was stopping whole process Fixes: 93259e8ca261 ("bcm4908: support "rootfs_data" on U-Boot devices") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* realtek: net: dsa: configure better brport flags when ports leave the bridgeBjørn Mork2022-03-061-0/+148
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ensures that the DSA driver sets exactly the same default flags as the bridge when a port joins or leaves. Without this we end up with a confusing flag mismatch, where DSA and bridge ports use different sets of flags. This is critical as the "learning" mismatch will be harmful to the network, causing all traffic to be flooded on all ports. The original commit was buggy, trying to set the flags one-by-one in a loop. This was not supported by the API and the end result was that all but the last flag were cleared. This bug was implicitly fixed upstream by commit e18f4c18ab5b ("net: switchdev: pass flags and mask to both {PRE_,}BRIDGE_FLAGS attributes"). This is a minimum temporary stop measure fix for the critical lack of "learning" only. The major API change associated with a full v5.12+ backport is neither required nor wanted. A simpler fix, moving the call to dsa_port_bridge_flags() out of the loop, has therefore been merged into this modified backport. Fixes: afa3ab54c03d ("realtek: Backport bridge configuration for DSA") Signed-off-by: Bjørn Mork <bjorn@mork.no> Acked-by: Daniel Golle <daniel@makrotopia.org> Tested-by: Stijn Tintel <stijn@linux-ipv6.be> [fix typos in commit message] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ramips: use parser_trx for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-062-2/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WCR-1166DS uses trx-fomatted firmware and the custom magic number (0x5C436F74, "\Cot") is required for OpenWrt installation from OEM WebUI. But the current mtdsplit_trx doesn't support the custom magic number and fail to parse and split to kernel and rootfs when the factory image is flashed. Then, the kernel fails to mount rootfs automatically and panics. Before the commit fddc78bc116bc043fb5cd92dbc45cfd054c21af8, mtdsplit_trx was patched in ramips target and the device-specific magic number was supported only for WCR-1166DS[1]. But the patch was not inherited to the later version of the kernel and deleted by the above commit, then, the custom magic number support was broken. [1]: https://github.com/openwrt/openwrt/blob/05d6e92594c507dcd1f4be6c1bcb2282fe1abe1f/target/linux/ramips/patches-4.4/0400-mtd-mtdsplit-add-support-for-custom-trx-magic-for-Buffalo-WCR-1166DS.patch#L27 log (factory image): [ 1.165312] spi-mt7621 10000b00.spi: sys_freq: 193333333 [ 1.195782] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 1.205353] 7 fixed-partitions partitions found on MTD device spi0.0 [ 1.217938] Creating 7 MTD partitions on "spi0.0": [ 1.227436] 0x000000000000-0x000000030000 : "u-boot" [ 1.238427] 0x000000030000-0x000000040000 : "u-boot-env" [ 1.250123] 0x000000040000-0x000000050000 : "factory" [ 1.261306] 0x000000050000-0x000000810000 : "firmware" [ 1.282051] 0x000000810000-0x000000fd0000 : "firmware2" [ 1.293594] 0x000000fd0000-0x000000fe0000 : "glbcfg" [ 1.304719] 0x000000fe0000-0x000000ff0000 : "board_data" ... [ 1.452424] /dev/root: Can't open blockdev [ 1.460619] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6 [ 1.475434] Please append a correct "root=" boot option; here are the available partitions: [ 1.491986] 1f00 192 mtdblock0 [ 1.491989] (driver?) [ 1.504938] 1f01 64 mtdblock1 [ 1.504941] (driver?) [ 1.517885] 1f02 64 mtdblock2 [ 1.517888] (driver?) [ 1.530831] 1f03 7936 mtdblock3 [ 1.530834] (driver?) [ 1.543777] 1f04 7936 mtdblock4 [ 1.543781] (driver?) [ 1.556724] 1f05 64 mtdblock5 [ 1.556727] (driver?) [ 1.569672] 1f06 64 mtdblock6 [ 1.569675] (driver?) [ 1.582617] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 1.598976] Rebooting in 1 seconds.. This patch fixes this issue by using parser_trx with specifying custom magic number in dts instead of mtdsplit_trx. log (fixed factory image): [ 1.202044] spi-mt7621 10000b00.spi: sys_freq: 193333333 [ 1.225369] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 1.235015] 7 fixed-partitions partitions found on MTD device spi0.0 [ 1.247603] Creating 7 MTD partitions on "spi0.0": [ 1.257106] 0x000000000000-0x000000030000 : "u-boot" [ 1.269447] 0x000000030000-0x000000040000 : "u-boot-env" [ 1.281192] 0x000000040000-0x000000050000 : "factory" [ 1.294208] 0x000000050000-0x000000810000 : "firmware" [ 1.305774] 2 trx partitions found on MTD device firmware [ 1.316540] Creating 2 MTD partitions on "firmware": [ 1.326399] 0x00000000001c-0x000000214754 : "linux" [ 1.336063] mtd: partition "linux" doesn't start on an erase/write block boundary -- force read-only [ 1.357070] 0x000000214754-0x0000007c0000 : "rootfs" [ 1.366994] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 1.386368] mtd: device 5 (rootfs) set to be root filesystem [ 1.398700] 1 squashfs-split partitions found on MTD device rootfs [ 1.411027] 0x000000520000-0x0000007c0000 : "rootfs_data" [ 1.422841] 0x000000810000-0x000000fd0000 : "firmware2" [ 1.436282] 0x000000fd0000-0x000000fe0000 : "glbcfg" [ 1.447408] 0x000000fe0000-0x000000ff0000 : "board_data" ... [ 1.611216] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: switch parser of trx for mt76x8 subtargetINAGAKI Hiroshi2022-03-061-1/+1
| | | | | | | | | | This patch enable parser_trx and disable mtdsplit_trx for mt76x8 subtarget. The trx format is used only on Buffalo WCR-1166DS in mt76x8 subtarget and the parser need to be switched to parser_trx to use the custom magic number in the header for WCR-1166DS. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: backport patch to allow using parser_trx from ramipsINAGAKI Hiroshi2022-03-061-0/+33
| | | | | | | This patch adds a patch to allow using parser_trx from ramips target, mainly for Buffalo devices. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: move parser_trx patches of custom magic to genericINAGAKI Hiroshi2022-03-065-4/+5
| | | | | | | | This patch moves the patches of parser_trx in mediatek target to generic/backport-5.10 to use the changes from ramips target and backport the additional patch of the parser. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: update MAC address configuration for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-061-2/+2
| | | | | | | | This patch converts MAC address configuration of Buffalo WCR-1166DS in 02_network to use the generic function of OpenWrt. And also, add label_mac. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: increase spi frequency for Buffalo WCR-1166DSINAGAKI Hiroshi2022-03-061-1/+1
| | | | | | | Use higher frequency than current and up the speed to access to the flash on WCR-1166DS. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: Add support for TP-Link TL-WPA8631P v3Joe Mullally2022-03-064-0/+217
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | AV1300 Gigabit Passthrough Powerline ac Wi-Fi Extender Specifications -------------- * SoC: MediaTek MT7621AT * CPU: 880 MHz MIPS 1004KEc dual-core CPU * RAM: 64 MiB DDR2 (Zentel A3R12E40DBF-8E) * Flash: 8 MiB SPI NOR (GigaDevice GD25Q64CSIG) * Ethernet: SoC built-in Switch 5x 1GbE * Port 0: PLC (connected through AR8035-A) * Port 1-3: LAN * WLAN: 2x2 2.4GHz 300 Mbps + 2x2 5GHz 867 Mbps (MT7603EN + MT7613BEN) * PLC: HomePlug AV2 (Qualcomm QCA7500) * PLC Flash: 2MiB SPI NOR (GigaDevice GD25Q16CSIG) * Buttons: Reset, LED, Pair, Wi-Fi * LEDs: Power (green), PLC (green/amber), LAN (green), 2.4G (green), 5G (green) * UART: J1 (57600 baud) * Pinout: (3V3) (GND) (RX) (TX) * Visually identify GND from connection to PCB ground plane Installation ------------ Installation is possible from the OEM web interface. Make sure to install the latest OEM firmware first, so that the PLC firmware is at the latest version. However, please first check the OpenWRT Wiki page for confirmation that your OEM firmware version is supported. Signed-off-by: Joe Mullally <jwmullally@gmail.com>
* mediatek: add support for Ruijie RG-EW3200GX PROLanghua Ye2022-03-054-1/+370
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | X32 Pro is another product name for it in the Chinese market. Specifications: - SoC: MT7622B - RAM: 256MB - Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR - Ethernet: 5x1GbE - Switch: MT7531BE - WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN - 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red) - 2Keys: Mesh button + Reset button - UART: Marked J19 on board. 3.3v, 115200n1 - Power: 12V 2.5A MAC addresses as verified by OEM firmware: use address source WAN *:F4 ethaddr@product_info LAN *:F5 5g *:F6 2g *:F7 Flash instruction: 1. Serve the initramfs.img using a TFTP server with address 10.10.10.3. 2. Interrupt the uboot startup process via UART. 3. Select "System Load Linux to SDRAM via TFTP" item. 4. (important) Back up firmware(mtd7) partitions with: dd if=/dev/mtd7 of=/tmp/firmware.bin and then download the firmware.bin image via SCP. 5. Flash the OpenWrt sysupgrade firmware. Recovery stock firmware: 1. Transfer the firmware.bin image to the device. 2. Flash the image with: mtd write firmware.bin firmware Signed-off-by: Langhua Ye <y1248289414@outlook.com>
* kernel: add support for XMC XM25QH128CLanghua Ye2022-03-051-0/+11
| | | | | | | The XMC XM25QH128C is a 16MB SPI NOR chip. The patch is verified on Ruijie RG-EW3200GX PRO. Datasheet available at https://www.xmcwh.com/uploads/435/XM25QH128C.pdf Signed-off-by: Langhua Ye <y1248289414@outlook.com>
* kernel: bump 5.10 to 5.10.103Rui Salvaterra2022-03-05153-1535/+523
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* bcm4908: support "rootfs_data" on U-Boot devicesRafał Miłecki2022-03-043-13/+122
| | | | | | | | | | | | | | | | | | | | | | | | | 1. Create "rootfs_data" dynamicaly U-Boot firmware images can contain only 2 UBI volumes: bootfs (container with U-Boot + kernel + DTBs) and rootfs (e.g. squashfs). There is no way to include "rootfs_data" UBI volume or make firmware file tell U-Boot to create one. For that reason "rootfs_data" needs to be created dynamically. Use preinit script to handle that. Fire it right before "mount_root" one. 2. Relate "rootfs_data" to flashed firmware As already explained flashing new firmware with U-Boot will do nothing to the "rootfs_data". It could result in new firmware reusing old "rootfs_data" overlay UBI volume and its file. Users expect a clean state after flashing firmware (even if flashing the same one). Solve that by reading flash counter of running firmware and storing it in "rootfs_data" UBI volume. Every mismatch will result in wiping old data. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: 5.10: remove CONFIG_DEVTMPFS{,_MOUNT} from kconfigsRui Salvaterra2022-03-016-11/+0
| | | | | | They are required for container support, but are handled in Config-kernel.in. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: 5.10: allocate last level PTEs in high memoryRui Salvaterra2022-03-017-7/+7
| | | | | | | | | | Enable support for allocating user space page table entries in high memory [1], for the targets which support this feature. This saves precious low memory (permanently mapped, the only type of memory directly accessible by the kernel). [1] https://www.kernel.org/doc/html/latest/vm/highmem.html Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.102John Audia2022-03-0118-90/+50
| | | | | | | | | | | | | | | Removed upstreamed: bcm4908/patches-5.10/180-i2c-brcmstb-fix-support-for-DSL-and-CM-variants.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.102&id=f333c1916fd6b55900029bf8f918cc00009e2111 Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-24 10:42:29 +0000