aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* bcm4908: sysupgrade: add pkgtb format supportRafał Miłecki2021-12-131-2/+183
| | | | | | | | | | | | | | BCM4908 devices with U-Boot use pkgtb firmware format. It's based on U-Boot's FIT: DTB with configurations, images & embedded data. This format contains bootfs, rootfs and optionally a first stage U-Boot loader. Contained images need to be extracted & flashed. Broadcom used two sets of firmwares: main & backup. It uses UBI volumes "metadata1" & "metadata2" for storing U-Boot env variables with info about flashed images. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: use uniform vendor value for british telecomMoritz Warning2021-12-124-6/+6
| | | | | | British Telecom is mostly known as BT. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* kernel: bump 5.10 to 5.10.83John Audia2021-12-1232-114/+59
| | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: bcm53xx/patches-5.10/033-v5.16-0024-ARM-dts-BCM5301X-Fix-I2C-controller-interrupt.patch[1] bcm53xx/patches-5.10/033-v5.16-0025-ARM-dts-BCM5301X-Add-interrupt-properties-to-GPIO-no.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=b2cd6fdcbe0a5cb44e4610a08cc58261d494a885 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=9db1d4a3c2700e1cc84c3d61199411d75c2a3ec6 Build system: x86_64* Build-tested: bcm2711/RPi4B, ipq806x/R7800† Run-tested: bcm2711/RPi4B, ipq806x/R7800† * Had to revert 7c99085bd69742f66207d61e9f2da5ec4f8f9d2f in order to build (latest bump of ca-certificates) † Had to revert 7f1edbd41295dff9f2127b169fbc086c0fb2c14e in order to build (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149) Signed-off-by: John Audia <graysky@archlinux.us>
* ipq40xx: fix reset button GPIO for GL.iNet GL-B2200Enrico Mioso2021-12-121-1/+1
| | | | | | | | | GL.iNet's U-Boot checks for GPIO 40, not 43. Changing this allows the RESET button to work as expected. Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> CC: Daniel Golle <daniel@makrotopia.org> CC: Li Zhang <li.zhang@gl-inet.com>
* ramips: add support for HUMAX E10Kyoungkyu Park2021-12-123-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | HUMAX E10 (also known as HUMAX QUANTUM E10) is a 2.4/5GHz band AC router, based on MediaTek MT7621A. Specifications: - SoC: MT7621A - RAM: DDR3 128MB - Flash: SPI NOR 16MB (MXIC MX25L12805D) - WiFi: - 2.4GHz: MT7615 - 5GHz: MT7615 - Ethernet: 2x 10/100/1000Mbps - Switch: SoC internal - USB: 1x USB 2.0 Type-A - UART: J1 (57600 8N1) - pinout: [3V3] (RXD) (GND) (TXD) Installation via web interface: - Flash **factory** image through the stock web interface. Recovery procedure: 1. Connect ethernet cable between Router **LAN** port and PC Ethernet port. 2. Set your computer to a static IP **192.168.1.1** 3. Turn the device off and wait a few seconds. Hold the WPS button on front of device and insert power. 4. Send a firmware image to **192.168.1.6** using TFTP. You can use any TFTP client. (tftp, curl, Tftpd64...) - It can accept both images which is HUMAX stock firmware dump (0x70000-0x1000000) image and OpenWRT **sysupgrade** image. Signed-off-by: Kyoungkyu Park <choryu.park@choryu.space> [remove trailing whitespace] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: mt76x8: tidy up 02_networkSungbo Eo2021-12-121-8/+5
| | | | | | | * fix alphabetic sorting * consolidate duplicate cases Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: fix RCU issue in xt_FLOWOFFLOAD patchFelix Fietkau2021-12-111-3/+1
| | | | | | cond_resched() may not be called in a rcu-locked section Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ath79: fix various dts warningsChristian Lamparter2021-12-1113-5/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ar9344_openmesh_mr600-v1.dts:40.10-44.5: Warning (gpios_property): /leds-ath9k/wifi2g: Missing property '#gpio-cells' in node /ahb/pcie-controller@180c0000/wifi@0,0 or bad phandle => added gpio-controller + #gpio-cells qca955x_zyxel_nbg6x16.dtsi:121.3-13: Warning (reg_format): /ahb/usb@1b000000/port@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) ../dts/qca955x_zyxel_nbg6x16.dtsi:131.3-13: Warning (reg_format): /ahb/usb@1b400000/port@1:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1) qca955x_zyxel_nbg6x16.dtsi:120.20-123.4: Warning (avoid_default_addr_size): /ahb/usb@1b000000/port@1: Relying on default #address-cells value => ath79's usb-nodes are missing the address- and size-cells properties. These are needed for usb led trigger support. ar7242_ubnt_sw.dtsi:54.4-14: Warning (reg_format): /gpio_spi/gpio_spi@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1) => the #address-cells and #size-cells had to be nudged. qca9531_dlink_dch-g020-a1.dts:19.6-39.4: Warning (i2c_bus_bridge): /i2c: incorrect #size-cells for I2C bus => #size-cells = <0>; Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* lantiq: fixed wifi support for AVM FRITZ!Box 7430Joel Linn2021-12-111-2/+4
| | | | | | | | | | | | adds the correct offset for the calibration data. The values are according to the OpenWrt Forum Thread: "Fritzbox 7430 and wifi". Link: <https://forum.openwrt.org/t/fritzbox-7430-and-wifi/86944> Reported-by: RENErica Signed-off-by: Joel Linn <jl@conductive.de> [changed commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for WD My Net N600Ryan Mounce2021-12-116-87/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: AR9344 RAM: 128MB Flash: 16MiB SPI NOR 5GHz WiFi: AR9382 PCIe 2x2:2 802.11n 2.4GHz WiFi: AR9344 (SoC) AHB 2x2:2 802.11n 5x Fast ethernet via SoC switch (green LEDs) 1x USB 2.0 4x front LEDs from SoC GPIO 1x front WPS button from SoC GPIO 1x bottom reset button from SoC GPIO UART header JP1, 115200 no parity 1 stop TX GND VCC (N/P) RX Flash factory image via "emergency room" recovery: - Configure your computer with a static IP 192.168.1.123/24 - Connect to LAN port on the N600 switch - Hold reset putton - Power on, holding reset until the power LED blinks slowly - Visit http://192.168.1.1/ and upload OpenWrt factory image - Wait at least 5 minutes for flashing, reboot and key generation - Visit http://192.168.1.1/ (OpenWrt LuCI) and upload OpenWrt sysupgrade image Signed-off-by: Ryan Mounce <ryan@mounce.com.au> [dt leds preparations] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: add support for jjPlus JWAP230Olivier Valentin2021-12-113-0/+195
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The jjPlus JWAP230 is an access point board built around the QCA9558, with built-in 2.4GHz 3x3 N WiFi (28dBm). It can be expanded with 2 mini-PCIe boards, and has an USB2 root port. Specifications: - SOC: Qualcomm Atheros QCA9558 - CPU: 720MHz - H/W switch: QCA8327 rev 2 - Flash: 16 MiB SPI NOR (en25qh128) - RAM: 128 MiB DDR2 - WLAN: AR9550 built-in SoC bgn 3T3R (ath9k) - PCI: 2x mini-PCIe (optional 5V) - LEDs: 6x LEDs (3 are currently available) - Button: 1x Reset (not yet defined) - USB2: - 1x Type A root port - 1x combined mini-PCIe - Ethernet: - 2x 10/100/1000 (1x PoE 802.3af (36-57 V)) Notes: The device used to be supported in the ar71xx target. For upgrades: Please use "sysupgrade --force -n <image>". This will restore the device back to OpenWrt defaults! MAC address assignment: use source LAN art 0x0 WAN art 0x6 WLAN art 0x1002 (as part of the calibration data) Flash instructions: - install from u-boot with tftp (requires serial access) > setenv ipaddr a.b.c.d > setenv serverip e.f.g.h > tftp 0x80060000 \ openwrt-ath79-generic-jjplus_jwap230-squashfs-sysupgrade.bin > erase 0x9f050000 +${filesize} > cp.b $fileaddr 0x9f050000 $filesize > setenv bootcmd bootm 0x9f050000 > saveenv Signed-off-by: Olivier Valentin <valentio@free.fr> [Added DT-Leds (based on ar71xx), Added more notes about sysupgrade, fixed "qca9550" to match SoC in commit and dts file name] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: remove old lzma tuning patchChristian Lamparter2021-12-111-22/+0
| | | | | | | | | | | | | | | | | | | | | Chen Minqiang reported in his GitHub PR #4733 that: With CONFIG_TARGET_INITRAMFS_COMPRESSION_LZMA=y option set, the popular x86/amd64 target's initramfs-kernel failed to boot. The cause for this boot failure is that the LZMA compression uses a the first bytes to encode the compression parameters. It does not have a fixed magic. Yes, this only works if the the existing lzma options in the upstream are not changed. This patch does away with OpenWrt special LZMA options tuning since it is rather unlikely that upstream will improve the compression algorithm detection after all this time. Even though, the tuning produced a smaller initramfs (~1.1% in a spot check). Link: <https://github.com/openwrt/openwrt/pull/4733> Reported-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* x86: add/improve support for Sophos SG/XG productsStan Grishin2021-12-112-4/+13
| | | | | | | | | * Better product ID for Sophos SG/XG-105 models * Add support for Sophos SG/XG-135 r1, r2 with/without wireless Signed-off-by: Stan Grishin <stangri@melmac.ca> [Changed subject to x86 - probably eaten somewhere, the PR had it] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: add more disabled config optionsJosef Schlehofer2021-12-111-0/+2
| | | | | | | | | | | | | | | | | | NET_DSA_MSCC_FELIX: Marvell 88E6xxx Ethernet switch fabric support (NET_DSA_MV88E6XXX) [N/m/y/?] n Ocelot / Felix Ethernet switch support (NET_DSA_MSCC_FELIX) [N/m/y/?] (NEW) Error in reading or end of file. make[6]: *** [scripts/kconfig/Makefile:71: syncconfig] Error 1 make[5]: *** [Makefile:603: syncconfig] Error 2 IR_IMON_RAW: SoundGraph iMON Receiver (early raw IR models) (IR_IMON_RAW) [N/m/?] (NEW) Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [squashed with "kernel: add missing IR_IMON_RAW config symbol"] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for Zbtlink ZBT-WG1602Sergey Ryazanov2021-12-053-0/+228
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zbtlink ZBT-WG1602 is a Wi-Fi router intendent to use with WWAN (UMTS/LTE/3G/4G) modems. The router board offsers a couple of miniPCIe slots with USB and SIM only and another one pure miniPCIe slot as well as five Gigabit Ethernet ports (4xLAN + WAN). Specification: * SoC: MT7621A * RAM: 256/512 MiB * Flash: 16/32 MiB (SPI NOR) * external watchdog (looks like Torexsemi XC6131B) * Eth: 10/100/1000 Mbps Ethernet x5 ports (4xLAN + WAN) * WLAN 2GHz: MT7603EN (.11n, MIMO 2x2) * WLAN 5GHz: MT7612EN (.11ac, MIMO 2x2) * WLAN Ants: detachable x2, shared by 2GHz & 5GHz radios * miniPCIe: 2x slots with USB&SIM + 1x slot with regular PCIe bus * WWAN Ants: detachable x4 * External storage: microSD (SDXC) slot * USB: 2.0 Type-A port * LED: 11 (5 per Eth phy, 3 SoC controlled, 2 WLAN 2/5 controlled, 1 power indicator) * Button: 1 (reset) * UART: console (115200 baud) * Power: DC jack (12 V / 2.5 A) Additional HW information: * SoC USB port #1 is shared by internal miniPCIe slot and external Type-A USB port, USB D+/D- lines are toggled between ports using a GPIO controlled DPDT switch. * Power of the USB enabled miniPCIe slots can be individually controlled using dedicated GPIO lines. * Vendor firmware feeds the external watchdog with 1s pulses. GPIO watchdog driver is able to either generate a 1us pulses or toggle the output line. 1us is not enough for the external watchod timer, so the line toggling driver mode is utilized. Installation: Vendor's firmware is OpenWrt (LEDE) based, so the sysupgrade image can be directly used to install OpenWrt. Firmware must be upgraded using the 'force' and 'do not save configuration' command line options (or correspondig web interface checkboxes) since the vendor firmware is from the pre-DSA era. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ath79: add support for TP-Link EAP225 v1Sander Vanheule2021-12-054-0/+64
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link EAP225 v1 is an AC1200 (802.11ac Wave-1) ceiling mount access point. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 2x2 * Wireless 5Ghz (QCA9882): a/n/ac, 2x2 * Ethernet (AR8033): 1× 1GbE, 802.3at PoE Flashing instructions: * Ensure the device is upgraded to firmware v1.4.0 * Exploit the user management page in the web interface to start telnetd by changing the username to `;/usr/sbin/telnetd -l/bin/sh&`. * Immediately change the malformed username back to something valid (e.g. 'admin') to make ssh work again. * Use the root shell via telnet to make /tmp world writeable (chmod 777) * Extract /usr/bin/uclited from the device via ssh and apply the binary patch listed below. The patch is required to prevent `uclited -u` in the last step from crashing. * Copy the patched uclited binary back to the device at /tmp/uclited (via ssh) * Upload the factory image to /tmp/upgrade.bin (via ssh) * Run `chmod +x /tmp/uclited && /tmp/uclited -u` to install OpenWrt. uclited patching: --- xxd uclited +++ xxd uclited-patched @@ -53811,7 +53811,7 @@ 000d2330: 8c44 0000 0320 f809 0000 0000 8fbc 0010 .D... .......... 000d2340: 8fa6 0a4c 02c0 2821 8f82 87c4 0000 0000 ...L..(!........ -000d2350: 8c44 0000 0c13 461c 27a7 0018 8fbc 0010 .D....F.'....... +000d2350: 8c44 0000 2402 0000 0000 0000 8fbc 0010 .D..$........... 000d2360: 1040 001d 0000 1821 8f99 8378 3c04 0058 .@.....!...x<..X 000d2370: 3c05 0056 2484 ad68 24a5 9f00 0320 f809 <..V$..h$.... .. To make sure the correct file is patched, the following MD5 checksums should match the unpatched and patched files: 4bd74183c23859c897ed77e8566b84de uclited 4107104024a2e0aeaf6395ed30adccae uclited-patched Debricking: * Serial port can be soldered on unpopulated 4-pin header (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors running from pins 1 (TXD) and 2 (RXD). Do NOT bridge the pull-down for pin 2, running parallel to the header. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via the LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr Tested by forum user KernelMaker. Link: https://forum.openwrt.org/t/eap225-v1-firmware/87116 Signed-off-by: Sander Vanheule <sander@svanheule.net>
* realtek: sort the port list numericallyBjørn Mork2021-12-051-4/+1
| | | | | | | | | | | Mac adresses are assigned in the order given by the port list. The interfaces are also brought up in this order. This target supports devices with up to 52 ports. Sorting these alphabetically is very confusing, and assigning mac addresses in alphabetic order does not match stock firmware behaviour. Suggested-by: Sander Vanheule <sander@svanheule.net> Signed-off-by: Bjørn Mork <bjorn@mork.no>
* realtek: update watchdog timer patchSander Vanheule2021-12-051-22/+45
| | | | | | | | The Realtek Otto watchdog timer driver was accepted upstream, and is queued for 5.17. Update the patch's file name, and replace by the final version. Signed-off-by: Sander Vanheule <sander@svanheule.net>
* x86: added support to generate VHDX imagesOldřich Jedlička2021-12-052-1/+7
| | | | | | | Added support to generate dynamic-sized VHDX images for Hyper-V. Compile-tested on x86 and run-tested on Windows 10 21H2 (Hyper-V). Signed-off-by: Oldřich Jedlička <oldium.pro@gmail.com>
* ipq806x: revert SDC clock changes for NBG6817 MMCShane Synan2021-12-052-24/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Revert the SDC "CLK_SET_RATE_GATE" changes to the SDC clock regulator structures. See https://elinux.org/images/b/b8/Elc2013_Clement.pdf > if ((clk->flags & CLK_SET_RATE_GATE) && clk->prepare_count) { > > For this particular clock, setting its rate is possible only if the > clock is ungated (not yet prepared) This fixes the MMC failing to initialize on newer ZyXEL NBG6817 hardware revisions with Kingston MMC. Older revisions should hopefully be unaffected. Check MMC hardware details with: cd /sys/block/mmcblk0/device/ && \ tail -v cid date name manfid fwrev hwrev oemid rev Known problematic MMC names (broken before this commit): * M62704 (dated 12/2018) via myself * M62704 (dated 11/2018) via Drake Stefani Known unaffected MMC names (already working without this commit): * S10004 (dated 12/2015) via slh Without enabling dynamic debugging, this error manifests in the kernel hardware serial console as the following: [ 2.746605] mmc0: error -110 whilst initialising MMC card […trimmed other messages…] [ 2.877832] Waiting for root device /dev/mmcblk0p5... Enabling Linux dynamic kernel debugging provides additional messages. For guidance, see the Linux kernel documentation: https://www.kernel.org/doc/html/latest/admin-guide/dynamic-debug-howto.html First, enable dynamic debugging in OpenWRT's configuration: 1. Run "make menuconfig" 2. Select "Global build settings --->" 3. Select "Kernel build options --->" 4. Enable "Compile the kernel with dynamic printk" via spacebar 5. Save and exit (arrow key to "Exit" until prompted to save, save) Alternatively, set "CONFIG_KERNEL_DYNAMIC_DEBUG=y" in your .config. Then, turn on dynamic debugging at boot: Modify bootargs in target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts to add… bootargs = "[…existing bootargs…] dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8"; For example: chosen { - bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1"; + bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1 dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8"; append-rootblock = "root=/dev/mmcblk0p"; Then, compile and flash the resulting build. If you are testing before this commit on newer MMC hardware, be prepared to recover! NOTE: If you have hardware serial console access, you don't need to use TFTP recovery to change the active boot partition. Reboot to working alternative partition via serial console: 1. Connect to hardware serial console * See https://openwrt.org/toh/zyxel/nbg6817#serial 2. Interrupt boot at "Hit any key to stop autoboot:" 3. Run "ATSE NBG6817" 4. Copy the result (e.g. "001976FE4B04") * Changes with **every boot** - can't reuse this 5. On your local system, run "./zyxel-uboot-password-tool.sh <copied value here>" * Example: "./zyxel-uboot-password-tool.sh 001976FE4B04" 6. Run the command provided by the password tool * Example: "ATEN 1,910F129B" * Changes with **every boot** - can't reuse this 7. Run "ATGU" * You now have full u-boot shell until next boot - unlocking is not remembered 8. Run either "run boot_mmc" (for booting partition set "FF") or "run boot_mmc_1" (for booting partition set "01") * These commands are not affected by dual-boot partition flags NOTE: This will NOT set the dual-boot partition flag. You'll need to fix that manually. The "nbg6817-dualboot" script may help: https://github.com/pkgadd/nbg6817/blob/master/nbg6817-dualboot zyxel-uboot-password-tool.sh - sourced from commit 459c8c9ef816156107e297964d088ddee2b4eef5: ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ a )) printf "ATEN 1,%X\n" $p Kernel serial console log BEFORE commit with dynamic debug enabled: […trimmed…] [ 3.171343] mmci-pl18x 12400000.sdcc: designer ID = 0x51 [ 3.171397] mmci-pl18x 12400000.sdcc: revision = 0x0 [ 3.175811] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz [ 3.181134] mmci-pl18x 12400000.sdcc: No vqmmc regulator found [ 3.186788] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio) [ 3.192902] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2 [ 3.215609] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0 [ 3.227532] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v [ 3.247518] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0 […trimmed…] [ 3.997725] mmc0: req done (CMD2): -110: 00000000 00000000 00000000 00000000 [ 4.003631] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000 [ 4.003659] mmc0: error -110 whilst initialising MMC card [ 4.016481] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0 Notice how the initial clock is 52 MHz, which is incorrect - MMC requires negotiation to enable higher speeds. Kernel serial console log AFTER commit with dynamic debug enabled: […trimmed…] [ 3.168996] mmci-pl18x 12400000.sdcc: designer ID = 0x51 [ 3.169051] mmci-pl18x 12400000.sdcc: revision = 0x0 [ 3.173492] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz [ 3.178808] mmci-pl18x 12400000.sdcc: No vqmmc regulator found [ 3.184702] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio) [ 3.190573] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2 [ 3.217873] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0 [ 3.229250] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v [ 3.249111] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0 […trimmed…] [ 4.392652] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000 [ 4.392785] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 1 [ 4.406554] mmc0: starting CMD6 arg 03b70201 flags 0000049d […trimmed…] Now, the MMC properly initializes and later switches to high speed. Thanks to: * Ansuel for maintaining/help with the IPQ806x platform, kernel code * slh for additional debugging and suggestions * dwfreed for confirming newer MMC details, clock frequency * robimarko for device driver debug printing help, clock debugging * Drake for testing and confirmation with their own newer NBG6817 ...and anyone else I missed! Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com> Tested-by: Shane Synan <digitalcircuit36939@gmail.com>
* mediatek: enable bmt on mt7622-rfb1Felix Fietkau2021-12-041-0/+11
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: bmt: use generic mtd apiChuanhong Guo2021-12-041-50/+57
| | | | | | | | | | | BMT replaces nand-specific ops for erasing and writing, but the mtk-snand driver only implements generic mtd api. Replace erase, block_isbad, block_markbad in mtd_info for generic mtd drivers. Fixes: b600aee3ed ("mediatek: attach bmt to the new snand driver") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add support for ipTIME A3004NS-dualYuchan Seo2021-12-042-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3004NS-dual is a 2.4/5GHz band router, based on Mediatek MT7621. Specifications: - SoC: MT7621 (880MHz) - RAM: DDR3 256M - Flash: SPI NOR 16MB - WiFi: - 2.4GHz: MT7602E - 5GHz : MT7612E - Ethernet: - 4x LAN - 1x WAN - USB: 1 * USB3.0 port - UART: - 3.3V, TX, RX, GND / 57600 8N1 Installation via web interface: - 1. Flash Initramfs image using OEM Firmware's web GUI - 2. Boot into OpenWrt and perform Sysupgrade with sysupgrade image. Revert to stock firmware: - 1. Boot into OpenWrt and perform Sysupgrade with OEM Stock Firmware image. Signed-off-by: Yuchan Seo <hexagonwin@disroot.org> Reviewed-by: Sungbo Eo <mans0n@gorani.run>
* kirkwood: add support for Ctera C200 V1 NASPawel Dembicki2021-12-046-1/+421
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 2-Bay NAS - maximum two 3.5" Harddisks Hardware: - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz - Ram: 512MB (4x Nanya NT5TU128M8GE-AC) - NAND Flash: 256MB (Samsung 216 K9F2G08U0C) - Lan: 1x GBE (Marvell 88E1116R-NNC1) - Storage: 2x SATA HDD 3.5" Slot - USB: 2x USB 2.0 port - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND) - LEDs: 13x GPIO controlled - Buttons: 2x GPIO controlled Known issues: - Buzzer is unused due lack of proper driver Installation: - Apply factory initramfs image via stock web-gui. - Do sysupgrade to make installation complete. Back to stock: - OpenWrt rootfs partition use unused space after stock firmware. - Full revert is possible. - Login via ssh and run: ctera_c200-v1_back_to_factory Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Reviewed-by: Sungbo Eo <mans0n@gorani.run> [apply sorting to device recipe] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: fix tl-mr3020-v3 switch topology to configure vlans via luciSergey V. Lobanov2021-12-041-1/+4
| | | | | | | | | | Currently it is not possible to configure VLANs via LUCI on tplink tl-mr3020-v3. This patch fixes switch topology for the LUCI interface. Signed-off-by: Sergey V. Lobanov <sergey@lobanov.in> [copied commit message from github PR] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: mt7620: Enable PHY aneg of Lava LR-25G001Pawel Dembicki2021-12-042-7/+6
| | | | | | | | | | | | | | | | | | | | | | | | | In 20b09a2125f5 Lava LR-25G001 router have problem with two inactive ethernet ports. JBOOT bootloader didn't configure ethernet devices by default. The same situation was there. It is required to enable all phy ports. This is fragment of stock bootlog: switch reg write_athr offset=90, value=2b0 switch reg write_athr offset=8c, value=2b0 switch reg write_athr offset=88, value=2b0 switch reg write_athr offset=84, value=2b0 switch reg write_athr offset=80, value=2b0 This patch adds proper registers configuration ar8337 initvals. 0x2b0 value causes force flow control configuration, 0x1200 was used instead (flow control config auto-neg with phy). [1] When switch is now ok, let's fix port numeration too. Fixes: 20b09a2125f5 ("ramips: add support for Lava LR-25G001") [1] https://github.com/openwrt/openwrt/pull/4806#issuecomment-982019858 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq40xx: nvmem cells for EZVIZ CS-W3-WD1200G EUPChristian Lamparter2021-12-043-6/+34
| | | | | | | | | | introduce nvmem pre-cal + mac-address cells for both Wifis and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of the few devices in which the correct mac adress is already at the right place for Wifi, so no separate nvmem cell is needed. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: unbreak EZVIZ CS-W3-WD1200G EUP on 5.10Christian Lamparter2021-12-042-1/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | with current images, the device is no longer booting. It gets stuck in the bootloader with "Config not available" and drops to the uboot shell. |flash_type: 0 |Hit any key to stop autoboot: 0 |SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB |Config not availabale |(IPQ40xx) # This is because the default bootcmd "bootipq" will only read the first four MiB of the kernel image. With 5.10 the gzip'd kernel is slightly larger. So the part of the FIT image which had the configuration is cut off. Hence it can't find it. To update the bootcmd, you have to attach the serial console again and enter the following commands into the boot prompt: # setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm" # saveenv # run bootcmd This will allow booting kernels with up to six MiB. This also allows us to drop the DEVICE_DTS_CONFIG hack we had to use. Note: uboot doesn't support LZMA. It fails with: "Unimplemented compression type 3" Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* gemini: only provide squashfs image for storlink-derivatesChristian Lamparter2021-12-041-0/+1
| | | | | | | | | The itian sq201, raidsonic ib-4220-b and storlink sl93512r can't boot from ext4. This is because the rootfstype in the device-tree bootargs is set to "squashfs,jffs2". (And ext4 was not designed for raw NOR flash chips). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mvebu: next backport mvnet MQPrio offloadKabuli Chana2021-12-034-0/+395
| | | | | | linux-next MQPrio patches adding TC traffic shaping offload Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
* ath79: add Embedded Wireless Balin PlatformCatrinel Catrinescu2021-12-033-0/+143
| | | | | | | | | | | | | | | | | | | | | | | | | | Add the Embedded Wireless "Balin" platform, it is in ar71xx too SoC: QCA AR9344 or AR9350 RAM: DDR2-RAM 64MBytes Flash: SPI-NOR 16MBytes WLAN: 2 x 2 MIMO 2.4 & 5 GHz IEEE802.11 a/b/g/n Ethernet: 3 x 10/100 Mb/s USB: 1 x USB2.0 Host/Device bootstrap-pin at power-up PCIe: MiniPCIe - 1 x lane PCIe 1.2 Button: 1 x Reset-Button UART: 1 x Normal, 1 x High-Speed JTAG: 1 x EJTAG LED: 1 x Green Power/Status LED GPIO: 10 x Input/Output multiplexed The module comes already with the current vanilla OpenWrt firmware. To update, use "sysupgrade -n --force <image>" image directly in vendor firmware. This resets the existing configurations back to default! Signed-off-by: Catrinel Catrinescu <cc@80211.de> [indent, led function+color properties, fix partition unit-address, re-enable pcie port, mention button+led in commit message] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: sysupgrade: drop disabled UBI to UBI logicBjørn Mork2021-12-031-22/+2
| | | | | | | | | | | | | | | | The commented out code is not required, as the comment indicates. The purpose of this code seems to be to avoid issues caused by partially overwriting an existing UBI partition, where some of the erase counters would be reset but not the unmodified ones. This problem has been solved in a more generic way by the UBI EOF marker. This ensures that any old PEBs after the marker are properly initialized. It is therefore unnecessary to erase the whole partition before flashing a new OpenWrt factory image. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ipq806x: sysupgrade: drop unnecessary UBI to UBI logicBjørn Mork2021-12-031-17/+1
| | | | | | | | | | | | | The purpose of this code seems to be to avoid issues caused by partially overwriting an existing UBI partition, where some of the erase counters would be reset but not the unmodified ones. This problem has been solved in a more generic way by the UBI EOF marker. This ensures that any old PEBs after the marker are properly initialized. It is therefore unnecessary to erase the whole partition before flashing a new OpenWrt factory image. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* kirkwood: sysupgrade: drop unnecessary UBI to UBI logicBjørn Mork2021-12-031-18/+1
| | | | | | | | | | | | | The purpose of this code seems to be to avoid issues caused by partially overwriting an existing UBI partition, where some of the erase counters would be reset but not the unmodified ones. This problem has been solved in a more generic way by the UBI EOF marker. This ensures that any old PEBs after the marker are properly initialized. It is therefore unnecessary to erase the whole partition before flashing a new OpenWrt factory image. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mvebu: sysupgrade: drop unnecessary UBI to UBI logicBjørn Mork2021-12-031-18/+1
| | | | | | | | | | | | | | | | | | The recent changes to the maximum kernel size for Mamba and Venom highlighted the fact that the old Mamba kernel size has been hardcoded in linksys_get_root_magic() even for devices with a different kernel/rootfs split. The purpose of this code seems to be to avoid issues caused by partially overwriting an existing UBI partition, where some of the erase counters would be reset but not the unmodified ones. This problem has been solved in a more generic way by the UBI EOF marker. This ensures that any old PEBs after the marker are properly initialized. It is therefore unnecessary to erase the whole partition before flashing a new OpenWrt factory image. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* mediatek: mt7623: switch to BPi-R2 to generic eMMC sysugpradeDaniel Golle2021-12-021-16/+3
| | | | | | | Make use of new functions in emmc.sh to implement sysupgrade on the BananaPi BPi-R2. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: mt7622: switch to generic eMMC sysupgradeDaniel Golle2021-12-022-18/+5
| | | | | | | Use functions in newly introduced emmc.sh for sysupgrade of the BananaPi BPi-R64. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: add support for GL.iNet GL-B2200TruongSinh Tran-Nguyen2021-12-028-2/+422
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro> [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [remove redundant check in platform.sh] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dishAlexander Couzens2021-12-027-3/+286
| | | | | | | | | | | | | | | | | | | | | | | | | | | | LHGG-60ad is IPQ4019 + wil6210 based. Specification: - Qualcomm IPQ4019 (717 MHz) - 256 MB of RAM (DDR3L) - 16 MB (SPI NOR) of flash - 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035. - WLAN: wil6210 802.11ad PCI card - No USB or SD card ports - UART disabled - 8x LEDs Biggest news is the wil6210 PCI card. Integration for its configuration and detection has already been taken care of when adding support for TP-Link Talon AD7200. However, signal quality is much lower than with stock firmware, so probably additional board-specific data has to be provided to the driver and is still missing at the moment. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [Fix Ethernet Interface] Signed-off-by: Nick Hainke <vincent@systemli.org>
* sunxi: update nanopi neo air that use brcmfmac43430a0Michel Promonet2021-12-021-1/+1
| | | | | | | | Update wifi firmware used for nanopi neo air, with cypress-firmware-43430-sdio there is no wifi detected, as brcmfmac-firmware-43430a0-sdio allow to acces to wifi. Signed-off-by: Michel Promonet <michel.promonet@free.fr>
* bcm4908: sysupgrade: refactor handling different firmware formatsRafał Miłecki2021-12-021-32/+76
| | | | | | | | | | This results in setting format specific data (format info, extract commands) in a single function. It should help maintaining sysupgrade code. This change has been tested on Asus GT-AC5300 and Netgear R8000P. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: sysupgrade: refactor handling different firmware formatsRafał Miłecki2021-12-021-165/+123
| | | | | | | | | | | | | | | | | | List of supported formats grew over time and implementation got a bit messy. There are multiple functions with format-specific parameters and commands. Refactor it by making platform_identify() setup all required info right after detecting firmware format. This simplifies formats handling in platform_other_check_image() and platform_do_upgrade() a lot. This has been tested on: 1. SmartRG SR400ac (TRX): non-NAND sysupgrade 2. Netgear R8000 (CHK): NAND aware and standard sysupgrade-s 3. D-Link DIR-885L (Seama): NAND aware and standard sysupgrade-s 4. Luxul XWR-3150 (LXL): NAND aware and standard sysupgrade-s Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: sysupgrade: simplify extracting image from Seama sealRafał Miłecki2021-12-021-15/+3
| | | | | | Use "oseama extract" which supports now writing to stdout. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* lantiq: xway_legacy: disable unused switchesAleksander Jan Bajkowski2021-11-301-8/+0
| | | | | | | | | | | | | | | | | | | | | The xway_legacy subtarget only supports 5 devices. Most compiled switch drivers are unused by any of these devices. The same drivers are compiled into the xway subtarget. They were probably copied from there when creating this subtarget. Switches used by devices: Arcadyan ARV4518PWR01 Realtek RTL8306SD Arcadyan ARV4518PWR01A Realtek RTL8306SD Arcadyan ARV4520PW Infineon ADM6996I Arcadyan ARV4525PW only PHY(IC+ IP101A) Arcadyan ARV452CQW Realtek RTL8306 The CONFIG_ETHERNET_PACKET_MANGLE symbol has also been disabled, as it is only needed by the driver for AR8216. Reduces kernel size by 19.9 kB. Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
* mpc85xx: Fix HiveAP-330 nvmem mac loaderMartin Kennedy2021-11-301-48/+54
| | | | | | | | | | | | | | | | We actually need to enclose the whole section of partitions in a `partitions { ... }` to assign it a `compatible = "fixed-partitions"; otherwise the partition referred to by `hwinfo` won't be registered when bringing up MTD partitions, for example as per: - <https://forum.openwrt.org/t/tp-link-c2600-missing-default-mac-mtd-partition-in-snapshot/103945/6> - commit e2b03c16eb44 ("ipq806x: add missing enclosing partitions block for TP-Link C2600")' Fixes: 8ec21d6bb210 ("mpc85xx: convert mtd-mac-address to nvmem implementation") Signed-off-by: Martin Kennedy <hurricos@gmail.com> [minor beautification] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* bcm4908: Deactivate pci featureHauke Mehrtens2021-11-291-1/+1
| | | | | | | | | | | This target does not activate CONFIG_PCI kernel configuration option, do not activate the PCI feature. This will deactivate some PCI drivers which are not building without PCI support in the kernel. If PCI_SUPPORT or PCIE_SUPPORT are activated in the kernel configuration the feature flag will be automatically set by the build system again. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Deactivate B53 symbols in generic configurationHauke Mehrtens2021-11-298-21/+10
| | | | | | | | | Deactivate all the symbols of the B53 DSA driver in the generic kernel configuration. Multiple targets are now using this drivers and they only need some of the options. This fixes the bcm4908 build which didn't deactivate all of the options. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* sunxi: remove kmod-rtc-sunxi for unsupported devicesChukun Pan2021-11-291-10/+10
| | | | | | | | | | | | | | | | From driver source: { .compatible = "allwinner,sun4i-a10-rtc", .data = &data_year_param[0] }, { .compatible = "allwinner,sun7i-a20-rtc", .data = &data_year_param[1] }, The rtc-sunxi module only supports allwinner a10 and a20 SoCs, other SoCs in the cortexa7 and cortexa53 subtarget using the CONFIG_RTC_DRV_SUN6I driver which is compiled into the kernel binary, so remove this package for these unsupported devices. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* realtek: netgear-gigabit: Add gpio-restart nodeSander Vanheule2021-11-281-0/+6
| | | | | | | | | | | | | | | | The Netgear GS110TPP v1 switch cannot reliably perform cold reboots using the system's internal reset controller. On this device, and the other supported Netgear switches, internal GPIO line 13 is connected to the system's hard reset logic. Expose this GPIO on all systems to ensure restarts work properly. Cc: Raylynn Knight <rayknight@me.com> Cc: Michael Mohr <akihana@gmail.com> Cc: Stijn Segers <foss@volatilesystems.org> Cc: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Sander Vanheule <sander@svanheule.net> Tested-by: Bjørn Mork <bjorn@mork.no>
* realtek: Enable gpio-restart driverSander Vanheule2021-11-281-0/+1
| | | | | | | | Add the gpio-restart driver to the realtek build. This way devices, which cannot reliably perform resets using the SoC's internal reset logic, can use a GPIO line to drive the SoC's hard reset input. Signed-off-by: Sander Vanheule <sander@svanheule.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 04:23:36 +0000