aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* target/linux/*: kmod-fs-ext{2,3} RIPJohn Crispin2014-07-1011-14/+10
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41560
* enable handling of the wan led on the WRT1900ACImre Kaloz2014-07-101-1/+1
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 41555
* kernel: revert an upstream linux-stable commit that is causing usb ↵Felix Fietkau2014-07-091-0/+206
| | | | | | | | regressions on some brcm47xx and ar71xx devices Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 41554
* kernel: 3.13: refresh patchesLuka Perkov2014-07-083-31/+20
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 41553
* kernel: ledtrig-netdev: use netdev_notifier_infoLuka Perkov2014-07-083-4/+31
| | | | | | | | | | Since kernel 3.11, the third parameter passed to notifier_call() is of type struct netdev_notifier_info. This patch fixes an oops when setting a netdev LED trigger. Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 41552
* kernel: update 3.14 to 3.14.11Luka Perkov2014-07-084-5/+5
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 41551
* brcm63xx: fixup patches borked by allowing too much fuzzJonas Gorski2014-07-0882-222/+210
| | | | | | | | | | Move defines and board_info structs back to their proper locations so (de-)selecting SOC support won't break the build. Reported-by: Álvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 41550
* brcm47xx: make reboot a more reliableHauke Mehrtens2014-07-072-0/+34
| | | | | | | | | | | | A reboot is issued by setting the watchdog timer to a low value, when the value is decreased from 1 to 0 by the hardware the system will reboot. Setting this value to 1 does not work every time, it is a little bit more reliable when setting it to 3. This timer runs with some MHz or KHz so nobody will notice the increased waiting. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41548
* brcm47xx: add buttons support for Netgear WNR3500LHauke Mehrtens2014-07-072-0/+50
| | | | | | | | Ticket: #14406 Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 41547
* brcm47xx: remove unneeded images from generic targetHauke Mehrtens2014-07-071-15/+0
| | | | | | | | | broadcom-wl now builds in the mips74k profile, so remove these chips from the generic profile. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41546
* rb532: remove broken markFelix Fietkau2014-07-071-1/+1
| | | | | | Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 41544
* rb532: add wan interfaceFelix Fietkau2014-07-071-0/+4
| | | | | | Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 41543
* rb532: fix jffs2 imagesFelix Fietkau2014-07-071-2/+2
| | | | | | Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 41542
* rb532: really fix squashfs imagesFelix Fietkau2014-07-073-2/+13
| | | | | | | | | | | | | The previous attempt (r40717) to fix squashfx made the system bootable but overlayfs remained broken. This enables block2mtd again using the right partition number and naming and adds MTD_ROOTFS_SPLIT option. However onboard rootfs partition name had to be renamed to place overlay on CF instead of onboard NAND. Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 41541
* kernel: do not build kernel modules by defaultHauke Mehrtens2014-07-064-93/+2
| | | | | | | | | | | No config option should be set to m in the default config, because there is also some script needed which picks the module up into the image and that is missing this way. Always create a kmod when building a module. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41539
* mpc83xx: add support for kernel 3.10Hauke Mehrtens2014-07-0611-0/+4552
| | | | | | | | This is compile tested only, please run test and report back. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41538
* mpc52xx: add support for kernel 3.10Hauke Mehrtens2014-07-061-0/+291
| | | | | | | | This is compile tested only, please run test and report back. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41537
* au1000: add support for kernel 3.10Hauke Mehrtens2014-07-066-0/+197
| | | | | | | | This is compile tested only, please run test and report back. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41534
* kernel: update 3.14 to 3.14.10Luka Perkov2014-07-065-10/+10
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 41533
* ar7: enable the low-memory feature flagJonas Gorski2014-07-061-1/+1
| | | | | | | | | Most ar7 devices have only 16 MiB RAM, so select low_mem to give them a chance to work. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 41532
* gemini: add support for kernel 3.10Hauke Mehrtens2014-07-0617-0/+4928
| | | | | | | | This is compile tested only, please run test and report back. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41531
* brcm47xx: image: legacy: take over old devices imagesHauke Mehrtens2014-07-061-25/+52
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 41530
* brcm47xx: image: mips74k: take over some device imagesHauke Mehrtens2014-07-061-20/+38
| | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41529
* brcm47xx: image: prepare for using mips74k subtargetHauke Mehrtens2014-07-061-0/+20
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 41528
* brcm47xx: fix bcm4705 rebooting when initializing the switch.Hauke Mehrtens2014-07-062-0/+34
| | | | | | | | | | | When the Ethernet controller is powered down and someone wants to access the mdio bus like the witch driver (b53) the system crashed if PCI_D3hot was set before. This patch deactivates this power sawing mode when a switch driver is in use. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41527
* b53: hardcode reset GPIO for Linksys WRT300N 1.1Hauke Mehrtens2014-07-061-0/+1
| | | | | | | | | | | | According to the thread https://forum.openwrt.org/viewtopic.php?id=48281 b53 uses GPIO 7: [ 4.470000] b53_common: [DBG] b53_switch_reset_gpio using 7 and causes device to self-reboot. GPIO 8 was found in CFE boot log: "Reset switch via GPIO 8 ..." Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 41526
* cns21xx: make patch apply againHauke Mehrtens2014-07-052-4/+4
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41522
* kernel: add missing config optionsHauke Mehrtens2014-07-054-0/+8
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41521
* brcm47xx: add LEDs for Netgear WNR3500LHauke Mehrtens2014-07-052-2/+54
| | | | | | | | | https://dev.openwrt.org/ticket/14406 Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41520
* brcm47xx: make it possible to unregister the adm switchHauke Mehrtens2014-07-052-54/+94
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41517
* brcm47xx: fix LEDs on WRTSL54GSHauke Mehrtens2014-07-052-2/+34
| | | | | | | | | https://dev.openwrt.org/ticket/16991 Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41516
* brcm47xx: increase fallback mac addresses by oneHauke Mehrtens2014-07-052-4/+4
| | | | | | | | | | Now the mac address is increased by two for the first fallback mac address. It could be that the address increased should be used for the wan port. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41515
* brcm47xx: do not use mac addresses with 00:90:4C prefix, prevent mac address ↵Hauke Mehrtens2014-07-052-0/+136
| | | | | | | | | | | | | | collisions. The address prefix 00:90:4C is used by Broadcom in their initial configuration. When a mac address with the prefix 00:90:4C is used all devices from the same series are sharing the same mac address. To prevent mac address collisions we replace them with a mac address based on the base address. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41513
* brcm47xx: get switch name from swconfig firstHauke Mehrtens2014-07-051-3/+5
| | | | | | | | | Without this patch the switch config for the adm switch did not worked, because hey are not names eth0. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41512
* adm6996: the GPIO interface for the adm6996l does not support switch statistics.Hauke Mehrtens2014-07-051-2/+9
| | | | | | | | | This patch deactivates the statistics, adds a missing lock initialization and fixes a waring. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41511
* ar71xx/rb532: move rc32434-fix-broken-pci.patch to the correct targetJohn Crispin2014-07-041-0/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41507
* brcm63xx: disable AUDITJonas Gorski2014-07-042-4/+0
| | | | | | | | Reduces kernel size by about 24k (6k compressed). Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 41506
* ar71xx: MIPS: RC32434: fix broken PCI resource initializationJohn Crispin2014-07-041-0/+37
| | | | | | | | https://patchwork.linux-mips.org/patch/6940/ Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41505
* brcm47xx: add LEDs for Asus RT-N15U and update RT-N66UHauke Mehrtens2014-07-032-2/+76
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 41501
* brcm47xx: migrate basic network settings from old releasesHauke Mehrtens2014-07-031-0/+29
| | | | | | | | | | | | | | | | Old OpenWrt releases were using network configs that are not valid anymore. They were specifying ports tagging in a different way (or were not tagging CPU at all) and were using VID 0 which is a reserved value. Modifying network configuration to apply all needed changes would be pretty tricky. Script /etc/init.d/netconfig that generates new config is quite complex itself. So instead let's save the most important settings, regenerate config from the scratch and restore values. This should work for 99% of users. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 41500
* kernel: add missing config optionHauke Mehrtens2014-07-034-0/+4
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41499
* realview: set LAN interface to be in DHCPFlorian Fainelli2014-07-031-0/+10
| | | | | | | | | | Realview is mostly used as a QEMU development platform, which will provide a built-in DHCP server to NAT or bridge the connection outside of the emulated environment. Signed-off-by: Florian Fainelli <florian@openwrt.org> SVN-Revision: 41495
* realview: disable SWP emulationFlorian Fainelli2014-07-031-0/+1
| | | | | | | | | This is not needed since our toolchain produces the expected binaries for the target CPU. Signed-off-by: Florian Fainelli <florian@openwrt.org> SVN-Revision: 41494
* brcm47xx: add CONFIG_LEDS_GPIO_REGISTERHauke Mehrtens2014-07-022-1/+1
| | | | | | | | CONFIG_LEDS_GPIO_REGISTER is selected by the bcm47xx arch code. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41488
* brcm47xx: refresh patchesHauke Mehrtens2014-07-022-5/+5
| | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41487
* brcm47xx: backport BCM47XX Linksys WRT54G series patchesHauke Mehrtens2014-07-026-0/+294
| | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> SVN-Revision: 41486
* kernel: disable CONFIG_IRQ_ALL_CPUS by defaultJohn Crispin2014-07-028-0/+8
| | | | | | | | this fixes the mpc85xx build error Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41477
* ramips: add missing rt3352 usb phy node to dtsJohn Crispin2014-07-021-2/+9
| | | | | | Signed-off-by: michael <igvtee@gmail.com> SVN-Revision: 41476
* ramips: fix target rt5350 only have 28 gpiosJohn Crispin2014-07-021-23/+4
| | | | | | Signed-off-by: michael <igvtee@gmail.com> SVN-Revision: 41475
* lantiq: UbinizeImage instead of lantiq-specific ubinize.cfg filesJohn Crispin2014-07-021-1/+23
| | | | | | | | | | New make target in lantiq to use UbinizeImage and SysupgradeNand. Only enabled for BTHOMEHUBV2B for the moment but should be useable for other lantiq nand boards. Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com> SVN-Revision: 41474
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-16 04:05:43 +0000