aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: vr9 fxs support: fixed check of SMP state within vpe-mt.cStefan Koch2017-03-131-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | SMP state is generally affected by - CONFIG_SMP build-time kernel configuration option and - 'nosmp' runtime kernel commandline option The SMP state within vpe-mt.c is determined by CONFIG_SMP option. A runtime check is needed if VPE functionality should be used with a kernel image that supports SMP. This fix introduces a check for 'nosmp' command line option if CONFIG_SMP kernel configuration option is enabled. Note: This patch is needed to use lantiq FXS if CONFIG_MIPS_MT_SMP (that activates CONFIG_SMP) is enabled within kernel configuration and the 'nosmp' command line argument is given to disable SMP at runtime. Without this patch CONFIG_MIPS_MT_SMP must be disabled before using FXS. With this patch setting the 'nosmp' parameter is enough. In general, concurrent usage of FXS and SMP is incompatible and will cause kernel panics. Signed-off-by: Stefan Koch <stefan.koch10@gmail.com>
* ipq806x: re-enable the RAM clock for gcc on 4.9Felix Fietkau2017-03-131-2/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: fix crash on 4.9 if the rpm clock probe happens before cpuidle initFelix Fietkau2017-03-131-0/+16
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: fix NAND support for linux 4.9Felix Fietkau2017-03-137-343/+397
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: do not allocate coherent memory in dma engine hotpathFelix Fietkau2017-03-131-15/+29
| | | | | | | | | | | The available amount of coherent DMA memory is very limited. On Linux 4.4 this issue was worked around by increasing the pool size. It turns out that using coherent memory here is completely unnecessary. This change reworks the driver code to use kzalloc+dma_map_single instead. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: clean up patches, port missing patches from 4.4John Crispin2017-03-1368-134/+4796
| | | | | Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: sync 4.9 kernel config with 4.4John Crispin2017-03-131-1/+21
| | | | | Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: clean up dts patching in 4.9Felix Fietkau2017-03-137-1159/+1298
| | | | | | | | | Do not patch upstream files, overwrite them entirely. The upstream files are buggy for a number of devices and this significantly simplifies the patch structure Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: enable cmdline mangle on 4.9 (like on 4.4)Felix Fietkau2017-03-131-2/+2
| | | | | Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: John Crispin <john@phrozen.org>
* ar71xx: WNDR4300: Fix network vlan IDsDaniel Gonzalez Cabanelas2017-03-131-3/+3
| | | | | | The Netgear WNDR4300 has the VLAN IDs flipped in LuCi, fix it. Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* ar71xx: WNDR4300: Fix switch HW controlled LEDsDaniel Gonzalez Cabanelas2017-03-131-4/+4
| | | | | | | | | | | | The Netgear WNDR4300, equipped with an Atheros AR8327 Gigabit Switch, has two LEDs on each port for monitoring LAN activity, but it currently only uses one. Fix the configuration to use both. The patch provides this new configuration: - green LED: 1 Gbps link, 4Hz blink frequency - amber LED: 10/100 Mbps link. 4Hz for 100Mbps, 2Hz for 10Mbps Signed-off-by: Daniel Gonzalez Cabanelas <dgcbueu@gmail.com>
* ar71xx: fix Wallys DR344 ethernet MAC addresses offsetsPiotr Dymacz2017-03-121-2/+3
| | | | | | | Without this fix, ethernet interfaces on Wallys DR344 use random MAC addresses. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: few minor cleanups in lib/ar71xx.shPiotr Dymacz2017-03-121-39/+16
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: fix boards order in lib/ar71xx.shPiotr Dymacz2017-03-121-276/+276
| | | | | | Keep everything within case statements in alphabetical order. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: shorten case statement patterns in lib/ar71xx.shPiotr Dymacz2017-03-121-13/+13
| | | | | | | | | | | | | | At now there is no general rule about what part of (or whole) machine name string should be used for board name assignment/detection and every target handles this in a different way. For most of the boards in ar71xx we already use only part of the string, generally without the vendor name. This shortens wildcards patterns in case statement for board name assignment, wherever possible (e.g. where it won't be misleading). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: always use double quotes in lib/ar71xx.shPiotr Dymacz2017-03-121-104/+104
| | | | | | | | | | Be consistent and always use double quotes for case statement patterns, as in other targets. With this approach it should be less confusing for users adding support for new devices. Also, be consistent with MikroTik boards wildcard pattern. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: fix indentation in lib/ar71xx.shPiotr Dymacz2017-03-121-19/+19
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix machine name for several devicesPiotr Dymacz2017-03-123-4/+4
| | | | | | Be consistent with form and format of the vendor name. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Rockeetech AP531B0Shuanglin Liu2017-03-1212-4/+148
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros QCA9531 (650/400/216 MHz (CPU/DDR/AHB)) - RAM: 64 MiB DDR2 - Storage: 16 MiB of flash (optional 16 MiB second flash) - Wireless: built into QCA9531 (Honey Bee), PHY modes b/g/n - Ethernet: 1x100M (port0) 1x100M (port 4) - PCI-E: x1 - SIMcard slot: x1 - USB 2.0 port: x1 (optional) - Ext GPIO pin: x8 - UART for serial console: x1 - External watchdog: x1 (optional) - Power supply: 9-48V (DC jack/passive PoE) Installation through tftp: - Copy <Firmware Image Name> into tftp directory - Connect board via ttl port and Ethernet port - Boot the AP531B0 - When "Autobooting in 1 seconds" appears press Enter - Set serverip and ipaddr appropriate (e.g. setenv serverip 192.168.88.10;setenv ipaddr 192.168.88.1) - Enter "tftp 0x8050000 <Firmware Image Name>" - Enter "erase 0x9f050000 +$filesize" - Enter "cp.b 0x80500000 0x9f050000 $filesize" - Enter "reset" Signed-off-by: Shuanglin Liu <roboidler@gmail.com>
* bcm53xx: parepare for building more Linksys imagesRafał Miłecki2017-03-121-1/+16
| | | | | | We still can't enable them by default without proper TRX support. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: update kernel 4.4 to 4.4.53Hauke Mehrtens2017-03-1210-123/+12
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update kernel 4.9 to 4.9.14Hauke Mehrtens2017-03-1226-207/+127
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* x86: image: drop unneeded grub callRafał Miłecki2017-03-121-1/+0
| | | | | | | It appears there isn't any Image/Build/grub/* define so this step looks redundant. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* x86: image: drop unused ROOTDELAY variableRafał Miłecki2017-03-121-2/+0
| | | | | | | It's unused since commit 742700719303 ("x86: remove the olpc subtarget, it has been unmaintained for a long time"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* imx6: add DSA driver for MV88E6176 switchTim Harvey2017-03-121-0/+8
| | | | | | | | | The MV88E6176 switch is present on the GW16083 and the GW5904 As of a5c32a1f1996f4f75504c4a9abd1c99eaa598df1 these drivers are to be enabled static in per-target kernels. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* imx6: add support for GW5904Tim Harvey2017-03-127-2/+699
| | | | Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* imx6: added fixfdt to bootscriptTim Harvey2017-03-121-0/+3
| | | | | | | If a 'fixfdt' uboot script exists, execute it prior to bootm to allow easy bootloader env based fdt fixups and tweaks Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* imx6: add missing dtb for imx6dl-gw553xTim Harvey2017-03-121-0/+1
| | | | Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* imx6: fix USB for 4.9 kernelTim Harvey2017-03-121-0/+8
| | | | Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* kernel: fix phy aneg crashTim Harvey2017-03-123-3/+3
| | | | | | | Fix a kernel crash caused when CONFIG_FIXED_PHY used for fixed phy drivers in phy-add-aneg-done-function patch. Signed-off-by: Tim Harvey <tharvey@gateworks.com>
* ramips: sort mt7620 image file alphabeticalMathias Kresin2017-03-121-246/+246
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Netgear EX3700Joseph C. Lehner2017-03-127-0/+184
| | | | | | | | | | | | | | | | Specifications: * SoC: MT7620A * RAM: 64 MB DDR * Flash: 8MB NOR SPI flash * WiFi: MT7612E (5Ghz) and builtin MT7620A (2.4GHz) * LAN: 1x100M The -factory images can be flashed from the device's web interface or via nmrpflash. Co-authored-by: Paul Oranje <por@xs4all.nl> Signed-off-by: Paul Oranje <por@xs4all.nl> Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
* ramips: add support for Netgear R6220Hanqing Wong2017-03-127-1/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear R6220, aka Netgear AC1200 and R6220-100NAS. Specification: - SoC: MediaTek MT7621ST (880 MHz) - Falsh: 128 MiB (Macronix MX30LF1G08AA-TI) - RAM: 128 MiB (Nanya NT5CB64M16FP-DH) - Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - Serial baud rate of Bootloader and factory firmware: 57600 Installation through telnet: - Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port on the router. - Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug (login if required, default: admin password) - You will see "Debug Enabled!" - Telnet 192.168.1.1 and login with "root" - ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for example. - cd /mnt/shares/myUdisk - mtd_write write rootfs.bin Rootfs - mtd_write write kernel.bin Kernel - reboot nmrpflash can be used to recover to the netgear firmware if a broken image was flashed. Signed-off-by: Hanqing Wong <hquu@outlook.com>
* mvebu: wrt3200acm enable SDIO interfaceHenryk Heisig2017-03-112-0/+11
| | | | | | add mwifiex-sdio package to wrt3200acm Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* lantiq: use the P2812HNUF* wan port as wanMathias Kresin2017-03-111-1/+1
| | | | | | | The port is labeled as wan and was only used as lan port because of the "tx ring full" issues fixed with 8f02f7c. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: xrx200: use vlan for ethernet wan portMathias Kresin2017-03-114-39/+9
| | | | | | | | | | | | | | | | | | | | | | | Using the lantiq,wan device tree property for one interface node and the lantiq,switch device tree property for another interface node at the same time was never intended/isn't supported at the moment. The property is meant to be used in two phy operation mode where one phy is assigned to an interface without lantiq,* device tree property and the other phy is assigned to an interface with the lantiq,wan device property to have two netdevs. If both properties are used at the same time, the lantiq,wan interface is shown as independent netdev but not able to operate independent. The port needs to be managed via swconfig. These dependency is not obvious and fooled already a lot of users. Add a default WAN vlan for xrx200 devices having an ethernet WAN port and remove the lantiq,wan device tree property. Leave it up to the user to set the ethernet WAN port as default WAN interface or to use this port as additional LAN port. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix broadcasts and vlans in two iface modeMathias Kresin2017-03-112-10/+12
| | | | | | | | | | | | | | | | | The two phy operation mode where one phy is assigned to an interface without lantiq,* device tree property and the other phy is assigned to an interface with the lantiq,wan device property was broken with the multicast package leaks between vlans fixes. Move the multicast packages relevant portmap settings to the condition which handles multicast packages for better readability. Replace the priv->port_map based port_map only for the interface which has the lantiq,switch device tree property set, to allow tagged multicast packages in two phy mode where the lantiq,switch device tree property isn't used. Signed-off-by: Mathias Kresin <dev@kresin.me>
* bcm53xx: prepare for building Archer C5 V2 imageRafał Miłecki2017-03-111-0/+9
| | | | | | Don't enable it yet as kernel needs to be updated first. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: Improve Sanlinking D240 configKristian Evensen2017-03-112-1/+12
| | | | | | | | | | | | | | | | | * The left most mini-PCIe slot (the one attached to SIM2) can be power-cycled by setting GPIO 0 to high/low. * The D240 only needs the MT76x2 module, so update makefile to reflect this. Note that until the default mt7620 target is updated, then kmod-mt76 (and thus kmod-mt7603) will be selected by default. v2->v3: * Indentation error. v1->v2: * Rename gpio and remove redundant comment (thanks Piotr Dymacz) Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ar71xx: add ath10k driver and firmware for Netgear R6100 to firmware imageStijn Segers2017-03-111-1/+1
| | | | | | | | A Netgear R6100 owner reported the LEDE images lack the ath10k driver and firmware [1]. This patch adds both to the R6100 image. [1] https://forum.lede-project.org/t/netgear-r6100-5ghz-wifi-not-working-after-initial-install/2222 Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* kernel: add another missing TPM symbolJohn Crispin2017-03-113-0/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ramips: kmod-sdhci-mt7620: switch dependence to kmod-mmcFurong Xu2017-03-113-5/+5
| | | | | | | mtk-mmc/mtk_sd.ko only depends on mmc_core and mmc_block. And, we remove kmod-sdhci dependence assignment from all related target devices. Signed-off-by: Furong Xu <xfr@outlook.com>
* mediatek: fix ESW EINT pinctrl defineJohn Crispin2017-03-111-2/+20
| | | | | | | This got lost while bumping the target to v4.9 causing ethernet issues on some boards. Signed-off-by: John Crispin <john@phrozen.org>
* bcm53xx: use upstream fix for iproc regressionRafał Miłecki2017-03-102-28/+131
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* bcm53xx: fix memory corruption caused by iproc PCE controller driverRafał Miłecki2017-03-091-0/+28
| | | | | | This is a simple revert of upstream patch for now. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mvebu: add default sata triggerAnsuel Smith2017-03-083-0/+60
| | | | | | | | | | | Change dts file to add default sata trigger to sata led. Backport upstream accepted patch to add sata trigger to device tree source files already upstreamed. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [backport upstream accepted patch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: enable disk led triggerAnsuel Smith2017-03-081-0/+1
| | | | | | As we have a disk led we enable the disk trigger that work with the easata port Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* lantiq: add support for the Alpha ASL56026Alex Maclean2017-03-083-0/+183
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ASL56026 is a VDSL2 router with dual 100mbit ethernet, also known as the ECI B-FOCuS V-2FUb/I. CPU: Lantiq XRX268 v1.1 at 333MHz Modem: Lantiq VRX208 RAM: 32MiB DDR2 at 167MHz Flash: 8MiB NOR, Spansion S29GL064N90TF04 UART is at JP1: Pin 1 TX Pin 2 GND Pin 3 +3.3V Pin 4 NC Pin 5 RX Boot selection pins are exposed via several resistor jumpers: boot_sel0 is at J15, on the rear of the board. Default is high. boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low. boot_sel2 is at J12, directly below the SoC. Default is low. boot_sel3 is at J16, on the rear of the board. Default is low. The boot_sel pins should never be shorted, the jumper must be moved or a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work) To install with the stock bootloader you must break the built in image selection process which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion This is done by setting loadaddr and both f_upgrade_addr vars to the same address: VR9 # setenv loadaddr 0xB0040000 VR9 # setenv f_upgrade_addr 0xB0040000 VR9 # setenv f_upgrade2_addr 0xB0040000 VR9 # saveenv Then flash the firmware image: VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin VR9 # erase B0040000 +${filesize} VR9 # cp.b 0x81000000 0xB0040000 ${filesize} Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* lantiq: clarify VG3503J nameAlex Maclean2017-03-081-1/+1
| | | | | | | Append the ECI model to the device name, to avoid confusion with the older model. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* kernel: backport first bcma 4.12 patch for GPIO and of_nodeRafał Miłecki2017-03-082-0/+24
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-14 08:29:50 +0000