aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add support for ZyXEL WRE6606Magnus Frühling2018-06-217-2/+300
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com> (cherry picked from commit 4b280ad91a6b155ac71c417aaa7bb5f4e328712f)
* ar71xx: add support for OCEDO KoalaDavid Bauer2018-06-2113-0/+205
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit e36f8b3f3980903d5cefc51fe274c19c7a0719f2)
* ar71xx: fix incorrect speed setting on QCA9556David Bauer2018-06-211-3/+17
| | | | | | | | | | The QCA9556 only has a SGMII interface. However the speed on the ethernet link is set for the non-existant xMII interface. This commit fixes this behavior. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit abb4ab076f37961a4dcaef4e87167b834f84e44e)
* ramips: Add support for Mikrotik RouterBOARD RBM33gTobias Schramm2018-06-217-1/+187
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Mikrotik RouterBOARD RBM33g. =Hardware= The RBM33g is a mt7621 based device featuring three gigabit ports, 2 miniPCIe slots with sim card sockets, 1 M.2 slot, 1 USB 3.0 port and a male onboard RS-232 serial port. Additionally there are a lot of accessible GPIO ports and additional buses like i2c, mdio, spi and uart. ==Switch== The three Ethernet ports are all connected to the internal switch of the mt7621 SoC: port 0: Ethernet Port next to barrel jack with PoE printed on it port 1: Innermost Ethernet Port on opposite side of RS-232 port port 2: Outermost Ethernet Port on opposite side of RS-232 port port 6: CPU ==Flash== The device has two spi flash chips. The first flash chips is rather small (512 kB), connected to CS0 by default and contains only the RouterBOOT bootloader and some factory information (e.g. mac address). The second chip has a size of 16 MB, is by default connected to CS1 and contains the firmware image. ==PCIe== The board features three PCIe-enabled slots. Two of them are miniPCIe slots (PCIe0, PCIe1) and one is a M.2 (Key M) slot (PCIe2). Each of the miniPCIe slots is connected to a dedicated mini SIM socket on the back of the board. Power to all three PCIe-enabled slots is controlled via GPIOs on the mt7621 SoC: PCIe0: GPIO9 PCIe1: GPIO10 PCIe2: GPIO11 ==USB== The board has one external USB 3.0 port at the rear. Additionally PCIe port 0 has a permanently enabled USB interface. PCIe slot 1 shares its USB interface with the rear USB port. Thus only either the rear USB port or the USB interface of PCIe slot 1 can be active at the same time. The jumper next to the rear USB port controls which one is active: open: USB on PCIe 1 is active closed: USB on rear USB port is active ==Power== The board can accept both, passive PoE and external power via a 2.1 mm barrel jack. The input voltage range is 11-32 V. =Installation= ==Prerequisites== A USB -> RS-232 Adapter and a null modem cable are required for installation. To install an OpenWRT image to the device two components must be built: 1. A openwrt initramfs image 2. A openwrt sysupgrade image ===initramfs & sysupgrade image=== Select target devices "Mikrotik RBM33G" in openwrt menuconfig and build the images. This will create the images "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" and "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" in the output directory. ==Installing== **Make sure to back up your RouterOS license in case you do ever want to go back to RouterOS using "/system license output" and back up the created license file.** Serial settings: 115200 8N1 The installation is a two-step process. First the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" must be booted via tftp: 1. Set up a dhcp server that points the bootfile to tftp server serving the "openwrt-ramips-mt7621-mikrotik_rbm33g-initramfs-kernel.bin" initramfs image 2. Connect to WAN port (left side, next to sys-LED and power indicator) 3. Connect to serial port of board 4. Power on board and enter RouterBOOT setup menu 5. Set boot device to "boot over ethernet" 6. Set boot protocol to "dhcp protocol" (can be omitted if DHCP server allows dynamic bootp) 6. Save config 7. Wait for board to boot via Ethernet On the serial port you should now be presented with the OpenWRT boot log. The next steps will install OpenWRT persistently. 1. Copy "openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" to the device using scp. 2. Write openwrt to flash using "sysupgrade openwrt-ramips-mt7621-mikrotik_rbm33g-squashfs-sysupgrade.bin" Once the flashing completes reboot the router and let it boot from flash. It should boot straight to OpenWRT. Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: Add lzma-loader targetsTobias Schramm2018-06-211-0/+16
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: Add support for mt7621 to lzma-loaderTobias Schramm2018-06-215-18/+60
| | | | Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
* ramips: fix Newifi D1 mtd partitionDeng Qingfang2018-06-211-1/+1
| | | | | | Newifi D1 has 32 MiB flash, so the firmware partition size should be 0x1fb0000 Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for ELECOM WRC-1167GHBK2-SINAGAKI Hiroshi2018-06-196-4/+175
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ELECOM WRC-1167GHBK2-S is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - MT7621A (2-Cores, 4-Threads) - 128 MB of RAM (DDR3) - 16 MB of Flash (SPI) - 2T2R 2.4/5 GHz - MediaTek MT7615D - 5x 10/100/1000 Mbps Ethernet - 6x LEDs, 2x keys - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 57600 bps Flash instruction using factory image: 1. Rename the factory image to "wrc-1167ghbk2-s_v0.00.bin" 2. Connect the computer to the LAN port of WRC-1167GHBK2-S 3. Connect power cable to WRC-1167GHBK2-S and turn on it 4. Access to "http://192.168.2.1/details.html" and open firmware update page ("手動更新（アップデート）") 5. Select the factory image and click apply ("適用") button 6. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for I-O DATA WN-GX300GRINAGAKI Hiroshi2018-06-196-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-GX300GR is a 2.4 GHz band 11n router, based on MediaTek MT7621S. Specification: - MT7621S (1-Core, 2-Threads) - 64 MB of RAM - 8 MB of Flash (SPI) - 2T2R 2.4 GHz - 5x 10/100/1000 Mbps Ethernet - 2x LEDs, 4x keys (2x buttons, 1x slide switch) - UART header on PCB - Vcc, GND, TX, RX from ethernet port side - baudrate: 115200 bps (U-Boot, OpenWrt) Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Rename OpenWrt initramfs image for WN-GX300GR to "uImageWN-GX300GR" and place it in the TFTP directory 3. Set the IP address of the computer to 192.168.99.8, connect to the LAN port of WN-GX300GR, and start the TFTP server on the computer 4. Connect power cable to WN-GX300GR and turn on the router 5. Press "1" key on the serial console to interrupt boot process on U-Boot, press Enter key 3 times and start firmware download via TFTP 6. WN-GX300GR downloads initramfs image and boot with it 7. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with sysupgrade image for WN-GX300GR 8. Wait ~150 seconds to complete flasing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-199-7/+484
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: mt7621: fix wireless package selectionMathias Kresin2018-06-191-5/+4
| | | | | | | Add wpad-mini if wireless drivers are included. Drop the mt76 package if both of the provided drivers are included with their own packages. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: reduce speed to gen1 for espressobin pcieTomasz Maciej Nowak2018-06-192-0/+116
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since the beginning there's been an issue with initializing the Atheros based MiniPCIe wireless cards. Here's an example of kerenel log: OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) pci 0000:00:00.0: BAR 0: assigned [mem0xe8000000-0xe801ffff 64bit] pci 0000:00:00.0: BAR 6: assigned [mem0xe8020000-0xe802ffff pref] [...] advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x44 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k 0000:00:00.0: enabling device (0000 -> 0002) advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x3c advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0xc advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x40 ath9k 0000:00:00.0: request_irq failed advk-pcie d0070000.pcie: Posted PIO Response Status: CA,0xe00 @ 0x4 ath9k: probe of 0000:00:00.0 failed with error -22 The same happens for ath5k cards, while ath10k card didn't appear at all (not detected): OF: PCI: host bridge /soc/pcie@d0070000 ranges: OF: PCI: MEM 0xe8000000..0xe8ffffff -> 0xe8000000 OF: PCI: IO 0xe9000000..0xe900ffff -> 0xe9000000 advk-pcie d0070000.pcie: link never came up advk-pcie d0070000.pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [mem0xe8000000-0xe8ffffff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff](bus address[0xe9000000-0xe900ffff]) advk-pcie d0070000.pcie: config read/write timed out Following the issue on esppressobin.net forum [1] the workaround seems to be limiting the speed of PCIe bridge to 1st generation. This fixed the initialisation of all tested Atheros wireless cards. The change shouldn't affect the performance for wireless cards, it could reduce the performance of storage controller cards but since OpenWrt focuses on wireless connectivity, fixing compatibility with wireless cards should be a priority. For the record, the iwlwifi and mt76 cards were not affected by this issue. 1. http://espressobin.net/forums/topic/which-pcie-wlan-cards-are-supported Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (cherry picked from commit 772258044b48036699302840abf96cd34c4e5078)
* mvebu: add fix for armada 37xx cpufreq driverTomasz Maciej Nowak2018-06-191-0/+35
| | | | | | | Backport from stable kernel tree fixing clock leak. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> (cherry picked from commit 4ec8c8c23ed50dbe9cabbfc544ae2780f0287fd0)
* kernel: atm: pppoatm fix vc-mux connection failuresKevin Darbyshire-Bryant2018-06-181-0/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Backport a hot off the press upstream kernel ATM fix: Preserve value of skb->truesize when accounting to vcc "There's a hack in pskb_expand_head() to avoid adjusting skb->truesize for certain skbs. Ideally it would cover ATM too. It doesn't. Just stashing the accounted value and using it in atm_raw_pop() is probably the easiest way to cope." The issue was exposed by upstream with: commit 14afee4b6092fde451ee17604e5f5c89da33e71e Author: Reshetova, Elena <elena.reshetova@intel.com> Date: Fri Jun 30 13:08:00 2017 +0300 net: convert sock.sk_wmem_alloc from atomic_t to refcount_t But an earlier commit left the ticking timebomb: 158f323b9868 ("net: adjust skb->truesize in pskb_expand_head() Sincerest thanks to Mathias Kresin <dev@kresin.me> for debugging assistance and to David Woodhouse <dwmw2@infradead.org> for further guidance, cajoling & patience in interpreting the debug I was giving him and producing a fix! Fixes FS#1567 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> (cherry picked from commit d600de3ddde269bf0b324735f8f12278f82d9b37)
* mips: fix dynamic ftraceVincent Wiemann2018-06-181-3/+8
| | | | | | | | | | | The kernel patch *-mips_module_reloc.patch breaks dynamic ftrace as dynamic ftrace depends on -mlong-calls. See http://patchwork.linux-mips.org/patch/675/ Thus we always set -mlong-calls if the kernel is being compiled with dynamic ftrace support. Signed-off-by: Vincent Wiemann <webmaster@codefetch.de> (cherry picked from commit 076d2ea6829855ee14ebd65230146eb27ee16750)
* ar71xx: add kmod-usb-ehci to fix USB on RB hAP ACThomas Nixon2018-06-181-1/+1
| | | | | Signed-off-by: Thomas Nixon <tom@tomn.co.uk> (cherry picked from commit bb71a3f27efb4140c47e98b933bdb64384cbcbbf)
* ipq40xx: essedma: fixup ip alignChen Minqiang2018-06-181-0/+26
| | | | | | | | | This fixup ip align in essedma driver rx path see cat /proc/cpu/alignment which reports alignment-fixups without this fix. Signed-off-by: Chen Minqiang <ptpt52@gmail.com> (cherry picked from commit 8f804f42d52e49191429ad1d716e7adb3cd10ceb)
* ipq806x: D7800 only has a single sata portJohn Crispin2018-06-181-0/+1
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit ee1dbffeed442b4968af48b2492ad41ac988dab8)
* mvebu: backport ahci_mvebu errata patchsetJeremiah McConnell2018-06-182-0/+334
| | | | | | | | | | | | | Marvell ahci hardware requires a workaround to prevent eSATA failures on hotplug/reset when used with multi-bay external enclosures. Errata Ref#226 - SATA Disk HOT swap issue when connected through Port Multiplier in FIS-based Switching mode. These patches backport the workaround from 4.17. Signed-off-by: Jeremiah McConnell <miah@miah.com> (cherry picked from commit e820455198aa50cc32f9a108a4696f0cc23023c3)
* mediatek: mt7622: Do not deactivate CONFIG_BLK_DEVHauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | | zram.ko needs CONFIG_BLK_DEV activated and it is by default for all other targets in OpenWrt. This makes zram.ko compile again. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 6745af9a0de28171b45c0e8584e393bd80f0a377)
* mediatek: mt7622: Do not set CPU_SUBTYPE for Cortex A53Hauke Mehrtens2018-06-181-1/+0
| | | | | | | | | | | | | Neon and vfpv4 are mandatory extensions in the ARM64 instruction set now, do not activate them explicitly. GCC will make use of these extension now by default. This makes it possible to share the toolchain with other Cortex A53 SoCs. Compile tested only. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> (cherry picked from commit 10ce015c652b1e48c1c113604e26481626fa6059)
* mvebu: enable SATA port multiplier supportJeremiah McConnell2018-06-181-0/+1
| | | | | | | | | | | Some of the Marvell targets have functional SATA port multiplier support, which is required for multi-bay eSATA enclosures. Enable kernel support by setting CONFIG_SATA_PMP. Closes: FS#1232 and FS#547 Signed-off-by: Jeremiah McConnell <miah@miah.com> (cherry picked from commit 390c4df2c0b2e7b31c52eca3dcba139b0d745a97)
* ar71xx: Fix offset to WMAC address for 8devices LimaSven Eckelmann2018-06-181-3/+1
| | | | | | | | | | | | | | | | | | | The ART partition of the Lima board stores exactly three mac addresses: * 0x0: eth0 * 0x6: eth1 * 0x1002: wmac The first two are correctly assigned in the mach file but the latter points to 0x800. But this position is set to ff:ff:ff:ff:ff:ff. Luckily, the driver falls back in ath9k_hw_init_macaddr to the EEPROM mac address when it doesn't find a valid mac address in the platform_data. Remove this bogus offset to the ART partition to directly load the wmac via the EEPROM data in the ART partition. Signed-off-by: Sven Eckelmann <sven@narfation.org> (cherry picked from commit 4f6320704f7e37368a1dae2deba767a73b3bf121)
* ipq806x: Limit NR_CPUS to 2Rosen Penev2018-06-181-1/+1
| | | | | | | | | | | ipq806x is all dual core processors. ipq807x is quad core. Removes this from dmesg: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2 Signed-off-by: Rosen Penev <rosenp@gmail.com> (cherry picked from commit fff65dbe2436351ea1feee6c79110971ec4d5881)
* mediatek: add missing symbols for mt7622John Crispin2018-06-181-1/+1
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 55f37310020c48ff575158791eb8dbcc6802c549)
* mediatek: add missing symbolsJohn Crispin2018-06-182-8/+8
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit de6162e832d028d24267d9cbfc64c71b9a7c5ec9)
* mediatek: add mt7622 subtargetJohn Crispin2018-06-187-1/+565
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 51740777fb37cb7bdc250d74b366840269439cf3)
* mediatek: backport upstream mediatek patchesJohn Crispin2018-06-18130-99/+21978
| | | | | Signed-off-by: John Crispin <john@phrozen.org> (cherry picked from commit 050da2107a7eb2a571a8a3d0cee21cc6a44b72b8)
* oxnas: reboot targetDaniel Golle2018-06-1872-10633/+1898
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reboot the oxnas target based on Linux 4.14 by rebasing our support on top of the now-existing upstream kernel support. This commit brings oxnas support to the level of v4.17 having upstream drivers for Ethernet, Serial and NAND flash. Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the new platform code and device-tree. Re-introduce base-files from old oxnas target which works for now but needs further clean-up towards generic board support. Functional issues: * PCIe won't come up (hence no USB3 on Shuttle KD20) * I2C bus of Akitio myCloud device is likely not to work (missing debounce support in new pinctrl driver) Code-style issues: * plla/pllb needs further cleanup -- currently their users are writing into the syscon regmap after acquireling the clk instead of using defined clk_*_*() functions to setup multipliers and dividors. * PCIe phy needs its own little driver. * SATA driver is a monster and should be split into an mfd having a raidctrl regmap, sata controller, sata ports and sata phy. Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20. Signed-off-by: Daniel Golle <daniel@makrotopia.org> (squash-picked commit 17511a7ea8 and commit dcc34574ef from master)
* kernel: bump 4.9 to 4.9.109 for 18.06Koen Vandeputte2018-06-182-4/+4
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.49 for 18.06Koen Vandeputte2018-06-183-9/+9
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86-64 Runtime-tested on: cns3xxx, imx6, x86-64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.108 for 18.06Koen Vandeputte2018-06-188-171/+193
| | | | | | | | | Refreshed all patches Compile-tested on: ar71xx Runtime-tested on: ar71xx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ramips: add support for TP-Link TL-WR842N v5Maxim Anisimov2018-06-166-1/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR842N v5 are simple N300 router with 5-port FE switch and non-detachable antennas. Its very similar to TP-Link TL-MR3420 V5. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - USB 2.0 Port - UART (J1) header on PCB (115200 8n1) - 7x LED, 2x button, power input switch Flash instruction: The only way to flash OpenWrt image in wr842nv5 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "lede-ramips-mt7628-tplink_tl-wr842n-v5-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: use phytpt trigger for mt76 wirelessDavid Bauer2018-06-161-4/+4
| | | | | | | | | | | | | With this change, the LED trigger is independent from the (wireless) netdev name. The (wireless) netdev name can be easiliy changed in OpenWrt and would require an update of the netdev trigger settings each time it is done. This change is (for now) applied only to MT7628 devices from TP-Link, as we only had the possibility to test this change against two of those devices, namely a TL-WR841 v13 and a Archer C50 v3. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix mt7688 watchdog register base addrlbzhung2018-06-161-2/+2
| | | | | | | | | | | | | I found mt7688 watchdog not working. The watchdog registers are identical for mt7621 and mt7628/mt7688. The first watchdog related register is at 0x10000100, the last one - a 16bit sized - at 0x10000128. Set the correct register address and size in the dtsi file to get the watchdog working. Signed-off-by: lbzhung <gewalalb@gmail.com> [add commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: fix conntrack fixup of offloaded flows on timeoutFelix Fietkau2018-06-143-9/+33
| | | | | | Fixes excessively long conntrack timeout of short lived connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: fix conntrack leak for flow_offload connectionsFelix Fietkau2018-06-143-28/+123
| | | | | | | This was caused by a race condition between offload teardown and conntrack gc bumping the timeout of offloaded connections Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: allow hardware NAT offload drivers to keep a priv pointerFelix Fietkau2018-06-141-0/+25
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: fix network config for ravpower wd03Matthias Badaire2018-06-091-1/+1
| | | | | | | | This device has only one ethernet port. Signed-off-by: Matthias Badaire <mbadaire@gmail.com> [add the existing eth0 as lan block, shorten commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: use Power-LED as Diag-LED on FRITZBox 4020David Bauer2018-06-092-1/+1
| | | | | | | This commit makes use of the Power-LED as Diag-LED, allowing the LED to work as a status indicator. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: fix AVM package selectionDavid Bauer2018-06-091-2/+2
| | | | | | | The AVM package selection partially broke with the addition of the FRITZ!Box 4020. This commit restores the intended behavior. Signed-off-by: David Bauer <mail@david-bauer.net>
* ar71xx: fix USB switch to mPCIE for Mikrotik rb91x boardsKoen Vandeputte2018-06-081-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some devices like the Mikrotik RB912 only have 1 USB port which is shared between an USB A type port, and the mini PCIe socket. Toggling a gpio selects the output to which USB is connected. Since kernel 4.9, gpio base is rounded up to a value of 32. Commit 65da6f9ca164 ("ar71xx: fix secondary gpio controller base values") accounts correctly for that. In this commit, rb912 sees it's value changed from AR934X_GPIO_COUNT (23) to 32 This means that the USB toggle gpio number actually also changes from 52 to 61. But .. Some of these GPIO numbers are also used in other locations, like the boardfile. The author forgot to also change them over there. Switching the USB port to mPCIe now shows my modem is correctly discovered again: [ 2863.864471] usb 1-1: new high-speed USB device number 4 using ehci-platform [ 2864.055303] usb 1-1: config 1 has an invalid interface number: 8 but max is 3 [ 2864.062728] usb 1-1: config 1 has no interface number 1 [ 2864.074567] qcserial 1-1:1.0: Qualcomm USB modem converter detected [ 2864.081474] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB0 [ 2864.111960] qcserial 1-1:1.2: Qualcomm USB modem converter detected [ 2864.118976] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB1 [ 2864.139808] qcserial 1-1:1.3: Qualcomm USB modem converter detected [ 2864.146777] usb 1-1: Qualcomm USB modem converter now attached to ttyUSB2 [ 2864.165276] qmi_wwan 1-1:1.8: cdc-wdm0: USB WDM device [ 2864.171879] qmi_wwan 1-1:1.8 wwan0: register 'qmi_wwan' at usb-ehci-platform-1, WWAN/QMI device, 02:00:44:ed:3b:11 Fixes: 65da6f9ca164 ("ar71xx: fix secondary gpio controller base values") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Cc: Robin Leblon <robin.leblon@ncentric.com> Cc: Felix Fietkau <nbd@nbd.name> (cherry picked from commit 55b4b1eba0af6d2240f48eb93d68fb2e9ff41b08)
* kernel: fix 811-pci_disable_usb_common_quirks.patchStijn Tintel2018-06-071-11/+12
| | | | | | | | | | The kernel bump wrongly modified the patch generic/pending-4.14/811-pci_disable_usb_common_quirks.patch. Sync it from master. Fixes: 1199a9109526 ("kernel: bump 4.14 to 4.14.48 for 18.06") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.14 to 4.14.48 for 18.06Stijn Segers2018-06-0786-1241/+956
| | | | | | | | | | | | | | Refreshed patches. The following patches were upstreamed and have been deleted: * target/linux/lantiq/patches-4.14/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch * target/linux/generic/pending-4.14/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch * target/linux/generic/pending-4.14/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch * target/linux/generic/pending-4.14/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch Compile-tested: ramips/mt7621, x86/64 Run-tested: ramips/mt7621 Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* kernel: bump 4.9 to 4.9.106 for 18.06Stijn Segers2018-06-0734-604/+398
| | | | | | | | | | | Refreshed patches. The following patches were upstreamed and have been deleted: * target/linux/ar71xx/patches-4.9/106-01-MIPS-ath79-fix-AR724X_PLL_REG_PCIE_CONFIG-offset.patch * target/linux/generic/pending-4.9/180-net-phy-at803x-add-support-for-AT8032.patch * target/linux/generic/pending-4.9/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch * target/linux/generic/pending-4.9/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ar71xx: switch CPE/WBS 210/510 to okli-loaderMatthias Schiffer2018-06-061-1/+4
| | | | | | | | | | | | | | | | | | | | | We recently increased the kernel partition size of the CPE/WBS 210/510. This works fine for new installations of the factory image, but on sysupgrades, the partition table read by the bootloader is not adjusted. This limits the maximum size of the kernel loaded by the bootloader to the old partition size. While adjusting the partition table would be a cleanest solution, such a migration would have to happen before an upgrade to a new version with a newer kernel. This is error-prone and would require a two-step upgrade, as we mark the partition table partition read-only. Instead, switch from the lzma-loader with embedded kernel to the okli-loader, so only the tiny lzma-loader is loaded by the bootloader as "kernel", and the lzma-loader will then load the rest of the kernel by itself. Fixes: e39847ea2f70 ("ar71xx: increase kernel partition size for CPE/WBS 210/510") Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: make loader-okli build step more genericMatthias Schiffer2018-06-061-2/+3
| | | | | | Add support for different loader types. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: lzma-loader: constify kernel argv arrayMatthias Schiffer2018-06-061-1/+1
| | | | | | | By making the kernel argv array const, the .data section can always be omitted from the laoder binary. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: lzma-loader: set page size to 4KBMatthias Schiffer2018-06-061-1/+1
| | | | | | | | The text section in the ELF loader is aligned to the maximum page size, which defaults to 64KB. Reduce it to the actual page size to avoid wasting flash space for this alignment. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ar71xx: lzma-loader: move padding workaround to gzip stepMatthias Schiffer2018-06-062-2/+5
| | | | | | | | | | | | | | | | | | | | | | | Some devices (TP-Link TL-WR1043ND v1) don't boot reliably when the uncompressed loader is too small. This was workarounded in the loader by adding 512KB of padding to the .data section of the loader binary. This approach had two issues: - The padding was only working when .data was non-empty (otherwise the section would become NOBITS, omitting it in the binary). .data was only empty when no CMDLINE was set, leading to further workarounds like fe594bf90d09 ("ath79: fix loader-okli, lzma-loader"), and this workaround was only effective because a missing "const" led to the kernel argv being stored in .data instead of .rodata - The padding was not only added to the compressed .gz loader, but also uncompressed .bin and .elf loaders. The prevented embedding the kernel cmdline in the loader for non-gz loader types. To fix both issues, move the creation of the padding from the linker script to the gzip step. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 05:50:37 +0000