aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.14 to 4.14.120Koen Vandeputte2019-05-2135-376/+258
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch - 060-fix-oxnas-rps-dt-match.patch Altered patches: - 0067-generic-Mangle-bootloader-s-kernel-arguments.patch - 006-mvebu-Mangle-bootloader-s-kernel-arguments.patch - 996-generic-Mangle-bootloader-s-kernel-arguments.patch Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ath79: glinet_gl-ar750s: Add USB power & microSDAlexander Wördekemper2019-05-202-8/+23
| | | | | | | | | The GL.iNet AR750S USB and microSD port is currently not working out of the box. GPIO 7 is used to control the power of the USB port. Add GPIO 7 as a fixed-regulator for the port. Also add &usb1 to DTS to get the microSD port to work. Signed-off-by: Alexander Wördekemper <alexwoerde@web.de>
* imx6: apalis: fix config survival after sysupgrade -nPetr Štetiar2019-05-201-0/+13
| | | | | | | | | This patch fixes `sysupgrade -n` when flashed with rootfs of the same size as currently running, so the rootfs_data wouldn't get destroyed and thus survive reboot. So let's fix it by always cleaning up the content of the rootfs_data during sysupgrade. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: add leds migrations for archer-c7-v5Petr Štetiar2019-05-201-0/+3
| | | | | | | | | ar71xx uses `archer-c7-v5` for led prefix, but ath79 sticks to more generic `tplink` as the DTS is reused by more boards, so we need to perform migrations of the LED names during upgrade. Cc: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: set mib-poll-interval on devices with ar8xxx switchPetr Štetiar2019-05-201-0/+50
| | | | | | | | | | | | | | Commit "generic: ar8216: add mib_poll_interval switch attribute" sets mib-poll-interval as disabled by default (was set to 2s), so it makes switch LEDs trigger disfunctional on devices which don't have mib-poll-interval set. So this patch sets mib-poll-interval to 500ms on devices which are using ar8xxx switch LEDs trigger, as the same value was set for built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch"). Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* apm821xx: set mib-poll-interval on emac0 attached ar83xx switchPetr Štetiar2019-05-202-0/+4
| | | | | | | | | | | | | Commit "generic: ar8216: add mib_poll_interval switch attribute" sets mib-poll-interval as disabled by default (was set to 2s), so it makes switch LEDs trigger disfunctional on devices which don't have mib-poll-interval set. So this patch sets mib-poll-interval to 500ms on devices which have ar83xx switch connected to emac0, as the same value was set for built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch"). Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: set mib-poll-interval on mdio0 attached ar83xx switchPetr Štetiar2019-05-206-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit "generic: ar8216: add mib_poll_interval switch attribute" sets mib-poll-interval as disabled by default (was set to 2s), so it makes switch LEDs trigger disfunctional on devices which don't have mib-poll-interval set. So this patch sets mib-poll-interval to 500ms on devices which have ar83xx switch connected to mdio0 bus, as the same value was set for built in switches in 443fc9ac35 ("ath79: use ar8216 for builtin switch"). Some measurements performed on TP-Link Archer C7-v5: mib-type=0, mib-poll-interval=500ms (10s pidstat) Average: %usr %system %guest %wait %CPU CPU Command Average: 0.00 1.93 0.00 0.00 1.93 - kworker/0:2 iperf3 (30s): 334 Mbits/sec mib-type=0, mib-poll-interval=2s (10s pidstat) Average: %usr %system %guest %wait %CPU CPU Command Average: 0.00 1.14 0.00 0.00 1.14 - kworker/0:2 iperf3 (30s): 334 Mbits/sec So it seems like we get 4x faster LED refresh rate for additional 0.8% CPU load. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* generic: ar8216: group MIB counters and use two basic ones only by defaultChuanhong Guo2019-05-203-81/+150
| | | | | | | | | | | | | | | | | There are too many MIB counters that almost nobody needs since commit d6366ce3665f ("generic: ar8216: mib_work_func: read all port mibs everytime"). In the worker function to poll MIB data, it deals with all ports instead of only one port every time, which introduces too many mdio operations that it becomes a heavy CPU load even on not-emulated MDIO bus. This commit groups MIB counters and enable only TxBytes and RxGoodBytes by default (both of which are necessary to get swconfig led working.) and adds an swconfig attribute to allow enabling all counters if users need them. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* generic: ar8216: add mib_poll_interval switch attributeChuanhong Guo2019-05-203-8/+63
| | | | | | | | | | | | | | This allows specifying interval of polling MIB counters from userspace and allow completely turning off MIB counter support by setting mib_poll_interval to 0. Since MIB counter polling is a heavy CPU load for GPIO emulated MDIO bus, disable this behavior by default. Those who wants to use swconfig LEDs can enable them with qca,mib-poll-interval dts property or with swconfig command. Fixes: FS#2230 ("kworker spikes 100% cpu every 2 second.") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* apm821xx: WNDR4700: remove obsolete sd-card change detectionChristian Lamparter2019-05-191-18/+0
| | | | | | | | | The SD-Card polling is now implemented by default in the fs-tools block-mount utility package. It might not be as fast as the current detection method since the polling time is 2 Seconds, but it's much less of an hack. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert WD MyNet Range Extender to gpio-keysChristian Lamparter2019-05-181-5/+1
| | | | | | | This patch converts the Range Extender to use the interrupt-driven gpio-keys driver over the polled variant. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: convert Netgear WNDR3700 series to gpio-keysChristian Lamparter2019-05-181-2/+1
| | | | | | | This patch converts the WNDR3700 to use the interrupt-driven gpio-keys driver over the polled variant. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ath79: use the qca,qca9563 chip compatible for the WR818Christian Lamparter2019-05-181-1/+1
| | | | | | | | | | | | | | | | | | | | All other QCA9563 devices already use this identifier for the exact SoC. Not that this matters much since as upstream states in Documentation/devicetree/usage-model.txt: "First and foremost, the kernel will use data in the DT to identify the specific machine. In a perfect world, the specific platform shouldn't matter to the kernel because all platform details would be described perfectly by the device tree in a consistent and reliable manner. [...] In the majority of cases, the machine identity is irrelevant, and the kernel will instead select setup code based on the machine's core CPU or SoC." Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for Telco Electronics X1Nicholas Smith2019-05-184-0/+184
| | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621 DRAM: 256MB DDR3 Flash: 16MB SPI-NOR WiFi: 2.4GHz: MT7603 @ PCIe0 WiFi: 5.8GHz: MT7612 @ PCIe1 Modem: Sierra Wireless MC74xx Interfaces: GBE RJ45 x5 mPCIe x2 UART x1 I2C x1 JTAG x1 UIM x1 LEDs x6 Flash instructions: Flash from within the factory bootloader, firmware web interface or CLI using sysupgrade -F -n Signed-off-by: Nicholas Smith <mips171@icloud.com>
* ath79: add support for TP-Link Archer D50 V1Davide Fioravanti2019-05-185-0/+219
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer D50 v1 is a dual-band AC1200 router + modem. The router section is based on Qualcomm/Atheros QCA9531 + QCA9882. The "DSL" section is based on BCM6318 but it's currently not supported. Internally eth0 is connected to the Broadcom CPU. Router section - Specification: CPU: QCA9531 650/600/200 MHz (CPU/DDR/AHB) RAM: 64 MB (DDR2) Flash: 8 MB (SPI NOR) Wifi 2.4GHz: QCA9531 2T2R Wifi 5GHz: QCA9982 2T2R 4x 10/100 Mbps Ethernet 8x LED, 3x button UART header on PCB Known issues: DSL not working (eth0) (WIP) UART connection --------------- J2 HEADER (Qualcomm CPU) . TX . RX . GND O VCC J16 HEADER (Broadcom CPU) O VCC . GND . RX . TX The following instructions require a connection to the J2 UART header. Flash instruction under U-Boot, using UART ------------------------------------------ 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-squashfs-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Initramfs instruction under U-Boot for testing, using UART ---------------------------------------------------------- 1. Press any key to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d50-v1-initramfs-kernel.bin bootm 0x81000000 Restore the original firmware ----------------------------- 0. Backup every partition using the OpenWrt web interface 1. Download the OEM firmware from the TP-Link website 2. Extract the bin file in a folder (eg. Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin) 3. Remove the U-Boot and the Broadcom image part from the file. Issue the following command: dd if="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin" of="Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod" skip=257 bs=512 count=15616 4. Double check the .mod file size. It must be 7995392 bytes. 5. Flash it using the OpenWrt web interface. Force the update if needed. WARNING: Remember to NOT keep settings. 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection. Issue below commands in the U-Boot: tftpboot 0x81000000 Archer_D50v1_0.8.0_1.3_up_boot(170223)_full_2017-02-24_09.37.45.bin.mod erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed default-state = "off", it's already the default, added pcie node, fixed typo]
* ath79: add support for Aruba AP-105Chris Blake2019-05-183-0/+199
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Atheros AR7161-8C1A @ 680 MHz RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR) WI1: Atheros AR9223-AC1A 802.11bgn WI2: Atheros AR9220-AC1A 802.11an ETH: Atheros AR8021-BL1E + PoE LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G BTN: 1 x Reset I2C: AT97SC4303s TPM (needs driver!) CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud Factory installation: - Needs a u-boot replacement. See Wiki for information on how to do a in-circut flash with a SPI-Flasher like a CH314A or flashrom. Wiki page can be found at https://openwrt.org/toh/aruba/aruba_ap-105 - Be careful when dis- and reassembling the device to not squish any of the antenna cables in the process! - Be sure to make a full 16 MiB backup of your device before flashing the new u-boot! This is needed if you ever have interest in reverting back to stock firmware. Not working: - TPM (needs a driver) Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* ramips: add factory image for WNDR3700v5Jan Hoffmann2019-05-183-17/+24
| | | | | | | | | This uses the existing rules for Sercomm factory images and moves them to the ramips image Makefile, so they can be used in all subtargets. The new factory image for WNDR3700v5 can be flashed using nmrpflash. Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ath79: Add support for TP-Link TL-WR1043N v5Adrian Schmutzler2019-05-184-3/+90
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - QCA9563 at 775 MHz - 64 MB RAM Zentel A3R12E40CBF-8E - 16 MB flash Winbond W25Q128FVSG - 3 (non-detachable) Antennas / 450 Mbit - 1x/4x WAN/LAN Gbps Ethernet (QCA8337) - reset and Wi-Fi buttons TP-Link TL-WR1043N v5 appears to be identical to the TL-WR1043ND v4, except that the USB port has been removed and there is no longer a removable antenna option. It also has different partitioning scheme. The software is more in line with the Archer series in that it uses a nested bootloader scheme. (This has been adapted from the OpenWrt Wiki page) <https://openwrt.org/toh/tp-link/tl-wr1043nd> Installation on HW rev.5: Factory firmware can be installed via the WEB interface. Alternatively, it is also possible to use a TFTP server for recovery purposes: - Rename OpenWRT or original firmware to WR1043v5_tp_recovery.bin - Set static IP of your PC to *192.168.0.66* - Router will obtain IP 192.168.0.86 for a few seconds while loading, when reset button pressed at power On. And finally, there's always u-boot access through the UART. For information visit the wiki. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworked commit message]
* ath79: Move TL-WR1043ND v1 definition to companionsAdrian Schmutzler2019-05-181-10/+10
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: Move settings specific for TP-Link TL-WR1043ND v4 to DTSAdrian Schmutzler2019-05-182-73/+70
| | | | | | This prepares for support of v5. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* gemini: Fix up firmware checksum on DIR-685Linus Walleij2019-05-181-0/+20
| | | | | | | | | | | | | | | | | | Using the same method as the D-Link DAP-2695 A1 we use the "mtd" tool to augment the firmware checkum in flash on first boot of a new firmware on the D-Link DIR-685. We need to augment the Makefile for "mtd" to build in the special WRGG fixup support for Gemini as well. This works around the problem of the machine not booting after factory install unless the sysupgrade is applied immediately. Based on commit e3875350f3e4185020b64e0588bba521cd1d6e64 "ar71xx: add support for D-Link DAP-2695 rev. A1" Cc: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* ramips: add support for HILINK HLK-7628NLiu Yu2019-05-184-0/+109
| | | | | | | | | | | | | | | | | | | | | | | | | Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 128 MB Flash: 32 MB WIFI: 802.11n/g/b 20/40 MHz Ethernet: 5 Port ethernet switch UART: 2x Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART0 line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. 5. After firmware is started connect via ethernet at 192.168.1.1 Signed-off-by: Liu Yu <f78fk@live.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
* ath79: add support for EnGenius ECB1750sven friedmann2019-05-186-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - Qualcomm Atheros SoC QCA9558 - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 1x 10/100/1000 Mbps Ethernet - 3T3R 2.4 GHz (QCA9558 WMAC) - 3T3R 5.8 Ghz (QCA9880-BR4A, Senao PCE4553AH) https://fccid.io/A8J-ECB1750 Tested and working: - lan, wireless, leds, sysupgrade (tftp) Flash instructions: 1.) tftp recovery - use a 1GbE switch or direct attached 1GbE link - setup client ip address 192.168.1.10 and start tftpd - save "openwrt-ath79-generic-engenius_ecb1750-initramfs-kernel.bin" as "ap.bin" in tfpd root directory - plugin powercord and hold reset button 10secs.. "ap.bin" will be downloaded and executed - afterwards login via ssh and do a sysuprade 2.) oem webinterface factory install (not tested) Use normal webinterface upgrade page und select "openwrt-ath79-generic-engenius_ecb1750-squashfs-factory.bin". 3.) oem webinterface command injection OEM Firmware already running OpenWrt (Attitude Adjustment 12.09). Use OEM webinterface and command injection. See wiki for details. https://openwrt.org/toh/engenius/engenius_ecb1750_1 Signed-off-by: sven friedmann <sf.openwrt@okay.ms> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [use interrupt-driven "gpio-keys" binding]
* ipq40xx: Add support for Linksys EA8300 (Dallas)Jeff Kletsky2019-05-1811-11/+847
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Installation: "Factory" images may be installed directly through the OEM GUI. Hardware Highlights: * IPQ4019 at 717 MHz (4 CPUs) * 256 MB NAND (Winbond W29N02GV, 8-bit parallel) * 256 MB RAM * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT): * 2.4 GHz radio at 30 dBm * 5 GHz radio on ch. 36-64 at 23 dBm * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1 * All two-stream, MCS 0-9 * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights * USB3, single port on rear with LED * WPS and reset buttons * Four status lights on top * Serial pads internal (unpopulated) "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1" Implementation Notes: The OEM flash layout is preserved at this time with 3 MB kernel and ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and syscfg (56 MB) partitions are untouched, available as read-only. Serial Connectivity: Serial connectivity is *not* required to flash. Serial may be accessed by opening the device and connecting a 3.3-V adapter using 115200, 8n1. U-Boot access is good, including the ability to load images over TFTP and either run or flash them. Looking at the top of the board, from the front of the unit, J3 can be found on the right edge of the board, near the rear | J3 | |-| | |O| | (3.3V seen, open-circuit) |O| | TXD |O| | RXD |O| | |O| | GND |-| | | Unimplemented: * serial1 "ttyQHS0" (serial0 works as console) * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1) Other Notes: https://wikidevi.com/wiki/Linksys_EA8300 states FCC docs also cover the Linksys EA8250. According to the RF Test Report BT BR+EDR, "All models are identical except for the EA8300 supports 256QAM and the EA8250 disable 256QAM." Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* mtd: base-files: Unify dual-firmware devices (Linksys)Jeff Kletsky2019-05-1812-161/+202
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line]
* zynq: make title consistent for all devicesLuis Araneda2019-05-171-4/+4
| | | | | | | | | | | | Modify the title to match the following format, as it's enough to uniquely identify a device: <manufacturer> <model> This matches what's done for other targets and has the added benefit of creating a sorted-by-manufacturer list of devices on menuconfig Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ramips: Add support for ZBT WE826-EKristian Evensen2019-05-175-1/+100
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the following specifications: - MT7620A (580 MHz) - 128MB RAM - 32MB of flash (SPI NOR) - 5x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus) - 2x SIM card slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 10x LEDs (4 GPIO-controlled) - 1x reset button The following have been tested and working: - Ethernet switch - wifi - miniPCIe slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. How to swap SIMs: You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio13/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio14/value). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: Add support for Head Weblink HDRM200Kristian Evensen2019-05-176-1/+208
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed specifications are: - MT7620A (580MHz) - 64MB RAM - 16MB of flash (SPI NOR) - 6x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM SIM7100E LTE modem. - 2x SIM slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 1x 5GHz wifi (mt7612) - 1x reset button - 1x WPS button - 3x GPIO-controllable LEDs - 1x 10 pin terminal block (RS232, RS485, 4 x GPIO) Tested: - Ethernet switch - Wifi - USB slot - SD card slot - miniPCIe-slot - sysupgrade - reset button Installation instructions: Installing OpenWRT for the first time requires a bit of work, as the board does not ship with OpenWRT. In addition, the bootloader automatically reboots when installing an image over tftp. In order to install OpenWRT on the HDRM200, you need to do the following: * Copy the initramfs-image to your tftp-root (default filename is test.bin) and configure networking accordingly (default server IP is 10.10.10.3, client 10.10.10.123). Start your tftp server. * Open the board and connect to UART. The pins are exposed and clearly marked. * Boot the board and press 1. * Either use the default filename and client/server IP-addresses, or specify your own. The image should now be loaded to memory and board boot. If the router reboots while the image is loading, you need to try again. Once the board has booted, copy the sysupgrade-image to the router and run sysupgrade in order to install OpenWRT to the flash. Notes: - You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio0/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio21/value). - RS485 is available on /dev/ttyS0. - RS232 is available on /dev/ttyS1. - The name of the ioX-gpios map to the labels on the casing. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [fixed whitespace issue and merge conflict in target.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: drop unused/incomplete dtsChuanhong Guo2019-05-173-230/+0
| | | | | | | | These dts itself are incomplete (e.g. missing mtd partitions) and its deivce support is never added to ath79 target. Drop these unused dts for now. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ath79: ar9330: fix switch_led_disable_pins reg valuePetr Štetiar2019-05-171-1/+1
| | | | | | | | | | | | | | In commit e9652e1696d9 ("ath79: fix pinmux for ar933x devices") I've wrongly changed desired register value to 0xf8 although it should've been set to 0x0. 0xf8 value sets bits 3-7 (ETH_SWITCH_LEDx_EN) to 1 which actually enables ethernet switch LEDs, so 0x0 is correct value in order to use the pins as GPIO. Fixes: e9652e1696d9 ("ath79: fix pinmux for ar933x devices") Reported-by: Chuanhong Guo <gch981213@gmail.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: archer-x7-v5: sync ar8327 initial reg values with ar71xxPetr Štetiar2019-05-171-2/+5
| | | | | | | | | Simply dumped content of this regs in ar71xx and wrote them to DTS, as a result port 6 on the switch will appear disconnected as on Archer C7v4. [AS: testing and PORT6_STATUS fix] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: Add missing reset button for TP-Link CPE210 v2 and v3Adrian Schmutzler2019-05-151-0/+10
| | | | | | | | Reset button support seems to be missing in ath79. Run-tested on CPE210 v2. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ath79: fix pinmux for ar933x devicesPaul Wassi2019-05-155-3/+9
| | | | | | | | | | | | | Properly disable the SoC's internal Switch LEDs on the pinmux. Devices that previously called ath79_gpio_function_disable for the switch LEDs, just need to reference switch_led_pins in the pinctrl-0 property of the gpio-leds node. Signed-off-by: Paul Wassi <p.wassi@gmx.at> [changed desired pinctrl register value from 0x1f to proper 0xf8] Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [renamed pinmux name to switch_led_disable_pins to make purpose more clear] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ath79: archer-x7-v5: remove confusing ar8327 initvals for LEDsPetr Štetiar2019-05-151-4/+0
| | | | | | | | This devices have LEDs connected to the SoC's GPIOs, so it makes no sense to fiddle with ar8327 LED regs. Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ar71xx: Fix network setup for TP-Link Archer C25 v1Adrian Schmutzler2019-05-151-10/+10
| | | | | | | | | Network for the Archer C25 v1 is set up without switch for no obvious reason. The LED setup is even done switch-based. This patch changes network setup so a switch is created. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* tegra: add vendor string to device nameTomasz Maciej Nowak2019-05-151-3/+3
| | | | | | | for better identification. Also create SUPPORTED_DEVICES string from it which corresponds to dts compatible string. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: add kmod-i2c-mux-pca954x for Turris OmniaJosef Schlehofer2019-05-151-1/+1
| | | | | | | | The driver is for the I2C mux. Schematic available at https://doc.turris.cz/doc/_media/rtrom01-schema.pdf Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz> Tested-by: Rosen Penev <rosenp@gmail.com>
* lantiq/xrx200: enable initramfs imagesStijn Segers2019-05-151-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Commit eae6cac6a3 ("lantiq: add support for AVM FRITZ!Box 7362 SL"), but one needs an initramfs image to flash OpenWrt from stock firmware (as described in the commit log). This patch has the initramfs image built by default. Thanks to blogic (for pointing to the FEATURES declaration in the target Makefiles) and Musashino on the forum for suggesting config/Config-images.in needed editing too. While at it, reorder the TARGET_INITRAMFS_COMPRESSION_LZMA declarations alphabetically. This patch will result in initramfs images for all lantiq subtargets that have the ramdisk flag set. I tested on the falcon and ase subtargets, which lack that flag, to confirm they don't produce any initramfs images with this patch - which they do not. Given the limited scope of the lantiq (sub)target(s), blogic indicated this should be OK. Signed-off-by: Stijn Segers <foss@volatilesystems.org> Signed-off-by: Petr Štetiar <ynezz@true.cz> [fixed the wrong reference to eae6cac6a3 commit]
* malta: Deactivate MIPS O32 and N32 supportHauke Mehrtens2019-05-142-12/+6
| | | | | | | | | OpenWrt is completely compiled from sources using a 64 bit compiler, we do not need support for the old 32 bit MIPS interface on 64 Bit CPUs, deactivate it. Fixes: 46af22de16b2 ("kernel: Remove CONFIG_COMPAT") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* octeon: Deactivate MIPS O32 and N32 supportHauke Mehrtens2019-05-142-12/+4
| | | | | | | | | OpenWrt is completely compiled from sources using a 64 bit compiler, we do not need support for the old 32 bit MIPS interface on 64 Bit CPUs, deactivate it. Fixes: 46af22de16b2 ("kernel: Remove CONFIG_COMPAT") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* octeon: Refresh kernel configurationHauke Mehrtens2019-05-142-2/+11
| | | | | | This refreshes the kernel configuration with "make kernel_oldconfig" Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Move some DSA config options to generic configHauke Mehrtens2019-05-144-10/+4
| | | | | | | This moves some new configuration options to the generic kernel configuration instead of configuring them for each target on our own. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* brcm63xx: fixup broken patch after kernel bumpJonas Gorski2019-05-141-1/+1
| | | | | | | | | | | | | | | | | | Fixes the following compilation issue that was introduced with the bump to 4.14.118: CC drivers/gpio/gpiolib-of.o drivers/gpio/gpiolib-of.c: In function 'of_gpiochip_add': drivers/gpio/gpiolib-of.c:510:12: error: too few arguments to function 'of_gpiochip_scan_gpios' status = of_gpiochip_scan_gpios(chip); ^~~~~~~~~~~~~~~~~~~~~~ drivers/gpio/gpiolib-of.c:247:5: note: declared here int of_gpiochip_scan_gpios(struct gpio_chip *chip, unsigned int start, ^~~~~~~~~~~~~~~~~~~~~~ scripts/Makefile.build:326: recipe for target 'drivers/gpio/gpiolib-of.o' failed Fixes: 09050b6fe228 ("kernel: bump 4.14 to 4.14.118") Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* kernel: bump 4.19 to 4.19.42Koen Vandeputte2019-05-139-181/+18
| | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch - 400-v5.2-leds-trigger-netdev-fix-refcnt-leak-on-interface-ren.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.118Koen Vandeputte2019-05-1312-114/+27
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 060-v5.1-serial-ar933x_uart-Fix-build-failure-with-disabled-c.patch Altered: - 143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.9 to 4.9.175Koen Vandeputte2019-05-132-5/+5
| | | | | | | | | Refreshed all patches. Compile-tested on: ar7 Runtime-tested on: none Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* brcm63xx: remove kernel 4.9 supportKoen Vandeputte2019-05-13204-23816/+0
| | | | | | | | | This target got bumped to 4.14 a long time ago in commit: 2308b87204206d84b6bf3dbc3d72591611cc6b78 Remove all leftover 4.9 files. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: Fix build of omap targetHauke Mehrtens2019-05-122-0/+2
| | | | | | | | CONFIG_HW_RANDOM_OMAP is not set to any value after kmod-random-omap was removed, add the configuration option to the generic configuration. Fixes: cd3b29853380 ("omap24xx: Remove unmaintained target") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: add images for additional ESPRESSObin boardsTomasz Maciej Nowak2019-05-118-1/+239
| | | | | | | | | | | | | | | | | | | | | This commit adds support for different iterations of ESPRESSObin. The added variants are: ESPRESSObin with soldered eMMC, ESPRESSObin V7, compared to V5 some passive elements changed and ethernet ports labels positions have been reversed, ESPRESSObin V7 with soldered eMMC. Please refer to: 584d7c5 ("mvebu: new subtarget cortex A53") for instruction how to boot OpenWrt image placed on SD card. It is advised for owners of V5 and previous with bootloader based on U-Boot 2015.01, to upgrade the latest version available at: http://espressobin.net/tech-spec. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: use device-tree board detectionTomasz Maciej Nowak2019-05-1117-179/+86
| | | | | | | | Convert whole target to Device Tree based board detection instead of identifying devices by dts file name. With this we can drop mvebu.sh translation script and rely on common method for model detection. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 09:06:24 +0000