aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
Commit message (Collapse)AuthorAgeFilesLines
* ramips: tl-wr840n-v5: increase firmware partition for 4Mmtk layotSerg Studzinskii2018-01-182-8/+2
| | | | | | | | | | | According to console log during TP-Link TL-WR840N v5 OEM firmware update procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store router's configuration settings, is erased and recreated again during every OEM firmware update procedure, thus does not contain any valuable factory data. So it is conviniant to use this extra 64kB erase block for jffs overlay due limited flash size on this device like it used on TP-Link's ar71xx boards. Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
* kirkwood: fix sysupgrade尤晓杰2018-01-181-1/+1
| | | | | | | | | | | | The platform_check_image() stub need to return 0 for success, otherwise the sysupgrade will fail with: Image check 'platform_check_image' failed. Fixes: aa6f5f1787a6 ("kirkwood: use image metadata") Signed-off-by: 尤晓杰 <yxj790222@163.com> [reworded commit message} Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: fix ZyXEL NBG6817 sysupgradeMathias Kresin2018-01-181-7/+10
| | | | | | | | | | | Use the first found directory in the tar archive instead of relying on a directory named according to the userspace boardname. It allows to change the boardname without adding another compatibility layer to the zyxel sysupgrade. Fixes: 33f09cf15178 ("ipq806x: convert to dt-based board-detection") Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: drop mdio-gpio.h include from mach-om5pacv2.cGabor Juhos2018-01-171-6/+0
| | | | | | | | | | | | | | The setup code of the OpenMesh OM5P ACv2 device uses nothing from the mdio-gpio.h header, so remove the inclusion of that. Also remove the kernel version check which is needed only because the mdio-gpio.h header exists in a different path in older kernels. Compile tested only. Cc: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* cns3xxx: switch to kernel 4.14Koen Vandeputte2018-01-171-1/+1
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: refresh patchesKoen Vandeputte2018-01-178-21/+21
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: remove deprecated uart flagsKoen Vandeputte2018-01-171-0/+29
| | | | | | | | Flag UPF_NO_TXEN_TEST is deprecated. Remove it. Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: fix ethernet IRQ imbalance in 4.14Koen Vandeputte2018-01-171-0/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Kernel 4.14 contains more warnings regarding NAPI usage, which showed following warning: [ 4016.420000] ------------[ cut here ]------------ [ 4016.430000] WARNING: CPU: 1 PID: 14 at kernel/irq/manage.c:525 __enable_irq+0x3c/0x78 [ 4016.440000] Unbalanced enable for IRQ 51 [ 4016.440000] Modules linked in: ath9k ath9k_common pppoe ppp_async ath9k_hw ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG slhc nf_reject_ipv4 nf_nat_redirs [ 4016.500000] CPU: 1 PID: 14 Comm: ksoftirqd/1 Tainted: G W 4.14.11 #0 [ 4016.500000] Hardware name: Gateworks Corporation Laguna Platform [ 4016.510000] Backtrace: [ 4016.510000] [<c010a28c>] (dump_backtrace) from [<c010a56c>] (show_stack+0x18/0x1c) [ 4016.520000] r7:c059df4b r6:00000000 r5:60000093 r4:00000000 [ 4016.530000] [<c010a554>] (show_stack) from [<c048b04c>] (dump_stack+0x94/0xb4) [ 4016.530000] [<c048afb8>] (dump_stack) from [<c011760c>] (__warn+0xc8/0xf8) [ 4016.540000] r7:c059df4b r6:c015144c r5:00000000 r4:cf863e08 [ 4016.550000] [<c0117544>] (__warn) from [<c011767c>] (warn_slowpath_fmt+0x40/0x48) [ 4016.550000] r9:cf863eb0 r8:00000036 r7:00000000 r6:c0636360 r5:00000033 r4:cf80a500 [ 4016.560000] [<c0117640>] (warn_slowpath_fmt) from [<c015144c>] (__enable_irq+0x3c/0x78) [ 4016.570000] r3:00000033 r2:c059e0c5 [ 4016.570000] [<c0151410>] (__enable_irq) from [<c01514ec>] (enable_irq+0x64/0x7c) [ 4016.580000] [<c0151488>] (enable_irq) from [<c0335c14>] (eth_poll+0x28c/0x558) [ 4016.590000] r5:d08926c0 r4:cf894488 [ 4016.590000] [<c0335988>] (eth_poll) from [<c03b1718>] (net_rx_action+0xfc/0x2e8) [ 4016.600000] r10:cf863eb8 r9:cf863eb0 r8:00000001 r7:0f7b5000 r6:c0636360 r5:cfdeb360 [ 4016.610000] r4:cf894488 [ 4016.610000] [<c03b161c>] (net_rx_action) from [<c0101510>] (__do_softirq+0xe0/0x228) [ 4016.620000] r10:00000100 r9:c070204c r8:c0702040 r7:00000003 r6:00000008 r5:40000003 [ 4016.620000] r4:cf862000 [ 4016.630000] [<c0101430>] (__do_softirq) from [<c011ae28>] (run_ksoftirqd+0x34/0x58) [ 4016.630000] r10:c0133964 r9:00000000 r8:00000001 r7:00000000 r6:c070b44c r5:cf862000 [ 4016.640000] r4:cf8037e0 [ 4016.640000] [<c011adf4>] (run_ksoftirqd) from [<c0133adc>] (smpboot_thread_fn+0x178/0x190) [ 4016.650000] [<c0133964>] (smpboot_thread_fn) from [<c013099c>] (kthread+0x11c/0x138) [ 4016.660000] r9:cf8037e0 r8:cf802cdc r7:cf839df8 r6:cf803800 r5:00000000 r4:cf802cc0 [ 4016.670000] [<c0130880>] (kthread) from [<c0107218>] (ret_from_fork+0x14/0x3c) [ 4016.680000] r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0130880 [ 4016.680000] r4:cf803800 r3:cf862000 [ 4016.690000] ---[ end trace 51114df08f429115 ]--- This is triggered by calling eth_schedule_poll(sw) after the IRQ has been re-enabled. Rework the network code to only enable IRQ's again if NAPI agrees it's safe to do so. Also only re-enable IRQ *after* cleaning up the RX ring and re-enabling DMA, which otherwise resulted in ugly warnings regarding dirty page fragments. These popped up nearly immediately when building the kernel with O2 iso Os. --> Note that this change fixes stability issues, at the cost of ~8% throughput performance. While at it, also change the iface name being used in warning prints, making it more obvious: "switch%d" --> "cns3xxx_eth" The changes have been tested on 4 boards, each moving ~30TB of data Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: update patches for 4.14Koen Vandeputte2018-01-176-64/+85
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: refresh kernel 4.14 configKoen Vandeputte2018-01-171-7/+97
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: copy patches for kernel 4.14Koen Vandeputte2018-01-1724-0/+1170
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* cns3xxx: copy config for kernel 4.14Koen Vandeputte2018-01-171-0/+300
| | | | Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ar71xx: fix format of the 701-MIPS-ath79-add-routerboard-detection patchesGabor Juhos2018-01-172-2/+2
| | | | | | | | | | | | Commit e15c63a37574 ("ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC") broke the format of the patches. In unified diff format, the unchanged, contextual lines must be preceded by a space character. Refresh the patches with quilt to fix them. Fixes: e15c63a37574 ("ar71xx: add support for MikroTik RouterBOARD wAPG-5HacT2HnD (wAP AC") Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: fix format of the 741-MIPS-ath79-add-PCI-for-QCA9556-SoC patchesGabor Juhos2018-01-172-12/+12
| | | | | | | | | | | The patches introduced in commit 20e68f6d395d ("ar71xx: kernel: enable PCI on QCA9556 SoC") have non standard format. In unified diff format, the unchanged, contextual lines must be preceded by a space character. Refresh the patches with quilt to fix them. Fixes: 20e68f6d395d ("ar71xx: kernel: enable PCI on QCA9556 SoC") Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* ar71xx: mach-rbspi: simplify reset button registrationGabor Juhos2018-01-171-64/+30
| | | | | | | | | | | | The setup code defines four individual structures for the Reset buttons of the supported boards. The only difference between the definitions is the GPIO number used for the button. Replace the different structures with one generic variant, and add a helper function to simplify the button registration. Signed-off-by: Gabor Juhos <juhosg@freemail.hu>
* imx6: add support for the intel gbit driver on GW5520Koen Vandeputte2018-01-171-0/+1
| | | | | | | | | | The Gateworks GW5520 board uses 2x intel gigabit mac's, instead of the internal i.MX6 FEC. Add support for these. Signed-off-by: Scott V. Kamp <outbackdingo@gmail.com> Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq8065: adjust SS USB PHY power settingsPavel Kubelun2018-01-171-0/+11
| | | | | | | | | | | According to QSDK ipq8065 has different SS USB PHY power settings. Adjust it according to QSDK settings. It also corresponds to oem Netgear R7800 tarball for soc ver >= 2. https://github.com/paul-chambers/netgear-r7800/blob/eeac2e10190f6f45e32e4c7012c4babc351898d8/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L2494 Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: usb: add phy 1 master reset controlPavel Kubelun2018-01-172-12/+26
| | | | | | | In current state only phy 0 master reset is controlled. Add the phy 1 reset. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: usb: Control USB master resetPavel Kubelun2018-01-172-0/+67
| | | | | | | | | | | | | | Picking commit from QSDK https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3 Commit message: "During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated." Change-Id: I537dc810f6cb2a46664ee674840145066432b957 Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org> (cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)" Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: dwc3: Fix power_on and power_off sequencePavel Kubelun2018-01-171-29/+58
| | | | | | | | | | | Picking commit from QSDK https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=d316437c9cdb70023a760342678f32e27241725a The commit fixes: - dwc3 phy module unloading - possibly fixes FS#177 when some devices were improperly enumerated as HS while being SS thus stucking the driver during boot. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: Update HSIO recommended usb phy settingsPavel Kubelun2018-01-171-15/+77
| | | | | | | | | | | | | | | | Picking commit from QSDK https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=cf82fdf4bdd081cd81bb081f7815b915bc8bb851 The comit adjusts USB dwc3 phy default values as per QSDK recomendation and allows to set it through DT. Commit message: "SoC version based values will be recovered from the device node. If device node does not have such values, defaults are applied. Change-Id: Ia77b5b7fe95ce1a433885df1761091bced98d989 Signed-off-by: Gokul Sriram Palanisamy <gpalan@codeaurora.org>" Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* Revert "ipq8064: Fix dwc3 module unloading"Pavel Kubelun2018-01-171-11/+3
| | | | | | | | Preparing for proper fixes thus reverting commits: - 8db079a9ff1756059250b801617a20baba214684 "ipq8064: Fix dwc3 module unloading" - c75f059b0c4d09dd0da60e14c4933a9f645266d1 "ipq8064: Fix dwc3 module unloading" Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: update clk and cpufreq driversPavel Kubelun2018-01-1716-814/+388
| | | | | | | | | | | | | A newer clk and cpufreq drivers for ipq806x platform had been sent upstream. A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing). Following patches are removed: - 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer. - 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch. - 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: force 2nd pci slot into gen1 modePavel Kubelun2018-01-1710-13/+17
| | | | | | | | | | | | | | According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode. EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode. In previous commit we've added the support for this option, so enable it in DT for affected devices. QSDK ref: https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506 While at it move the phy transmit termination offset value into dtsi file as it's platform specific. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: fix wireless regressionPavel Kubelun2018-01-1710-308/+734
| | | | | | | | | | | | | | | | In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues. https://bugs.lede-project.org/index.php?do=details&task_id=1197 This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant Unfortunately qca developers do not bother to push it upstream. Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration. Fixes: FS#1197 and probably others Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ramips: use blue status LED for Xiaomi Router 3GDaniel Gimpelevich2018-01-151-3/+1
| | | | | | | | | | | | The blue LED is what other firmwares use for this device, and it's a lot easier on the eyes than its shade of yellow, which implies an error condition. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [merge into existing $boardname:blue:status block] Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: Piotr Dymacz <pepe2k@gmail.com> Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips: add support for TP-Link Archer C20 v4Maxim Anisimov2018-01-156-0/+191
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C20 v4 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 3x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power input switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. * MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't work. Flash instruction: The only way to flash LEDE image in ArcherC20v4 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1Maxim Anisimov2018-01-157-39/+37
| | | | | | | | This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1" because of TPLINK released new TP-Link Archer C20 v4. Additionally migration to the generic board detection has been made. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ar71xx: fix TP-Link Archer C7 v4 switch LEDsDavid Bauer2018-01-151-8/+12
| | | | | | | | Match mapping of the switch LEDs according to the TP-Link firmware behavior. LAN port 1 triggers the most right LAN LED, LAN port 2 the second LAN LED from the right and so on. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add image checksChen Minqiang2018-01-151-8/+5
| | | | | | | As long as we can't enforce image metadata, we need to use (platform) image checks to have at least soem kind of validation. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ipq806x: drop ubifs supportMathias Kresin2018-01-152-10/+1
| | | | | | | | Ubifs is disabled for all boards except the evaluation boards and the Fritz!Box 4040 anyway. According the author, the ubifs support for the Fritz!Box 4040 wasn't enabled on purpose. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: drop legacy image leftoversMathias Kresin2018-01-151-24/+0
| | | | | | | Remove leftover code used for legacy images. There are no relevant binary differences for the images after removing the legacy leftovers. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: unset filesystem specific build command by defaultMathias Kresin2018-01-151-0/+1
| | | | | | | | | | | | | Initialise the filesystem specific build command. Otherwise it will be unintended inherit to following images and will cause a wrong image format. The issue is around for ages but was only recently triggered due to the added support for the Openmesh a42. Fixes: FS#1276 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: remove unnecessary filesystem specific buildMathias Kresin2018-01-151-1/+1
| | | | | | The Openmesh factory image doesn't need a squashfs specific build command. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: use bin file extension for sysupgrade-tar imagesMathias Kresin2018-01-151-8/+8
| | | | | | | Use the file extension bin for sysupgrade-tar images to unify the file extension across the target/tree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx: image: rework EnGenius ENS202EXT factory imagePiotr Dymacz2018-01-151-7/+4
| | | | | | | | | Current EnGenius ENS202EXT factory image recipe version causes factory images of the following devices to be corrupted. This issue wasn't visible until recent changes of image Makefile snippets order. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* omap24xx: remove referece to not existing kmod-usb-musb-tusb6010Jo-Philipp Wich2018-01-151-1/+1
| | | | | | | | Remove leftover reference to a not existing kmod-usb-musb-tusb6010 from the omap24xx target, the corresponding module is built into the kernel. Fixes: 96815fe0a2 ("kernel: remove omap24xx specific kernel module packages") Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ar71xx: add support for MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC)Roger Pueyo Centelles2018-01-159-10/+112
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the MikroTik RouterBOARD wAP G-5HacT2HnD (wAP AC), a small weatherproof dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional anntennae and one 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/RBwAPG-5HacT2HnD for more info. Specifications: - SoC: Qualcomm Atheros QCA9556 - RAM: 64 MB - Storage: 16 MB NOR - Wireless: · Atheros AR9550 (SoC) 802.11b/g/n 2x2:2, 2 dBi antennae · Qualcomm QCA9880 802.11a/n/ac 3x3:3, 2 dBi antennae - Ethernet: Atheros AG71xx (SoC, AR8033), 1x 1000/100/10 port, passive PoE in Working: - Board/system detection - Sysupgrade - Serial console - Ethernet - 2.4 GHz radio - 5 GHz radio - Reset button Not working: - LEDs (added according to Mikrotik's GPL sources but not functional) Unsupported: - ZT2046Q SPI temperature and voltage sensor Contributors: Giuseppe Tipaldi (@Ciusss89) Ricky (@rickydee) Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [daniel@makrotopia.org: whitespace fix, use PHYADDR instead of PHYMASK]
* ar71xx: kernel: enable PCI on QCA9556 SoCRoger Pueyo Centelles2018-01-152-0/+24
| | | | | | | | | This patch enables the PCI bus on the QCA9556 SoC, the same way it is done on the same family SoC QCA9558. Tested on a MikroTik RouterBoard wAPG-5HacT2HnD (wAP AC). Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: add support for ALFA Network AC1200RMPiotr Dymacz2018-01-156-6/+193
| | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN. Specification: - MT7620A (580 MHz) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4 - 2T2R 2.4 GHz (MT7620A) - 2T2R 5 GHz (MT7612EN) - 1x USB 2.0 - 9x LED (8 driven by GPIO) - 1x button (reset) - DC jack for main power input (12-24 V) - 2x UART, I2C, I2S and LED headers Flash instruction (do it under U-Boot, using UART and TFTP server): Select option "2: Load system code then write to Flash via TFTP" and use "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for GL.iNet GL-AR750Piotr Dymacz2018-01-1515-10/+198
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | GL.iNet GL-AR750 is a small size, dual-band (AC750) router, based on Qualcomm/Atheros QCA9531 v2 + QCA9887. FCC ID: 2AFIW-AR750. Specification: - 650/597/216 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3x 10/100 Mbps Ethernet - 2T2R 2.4 GHz (QCA9531) - 1T1R 5 GHz (QCA9887) - 1x USB 2.0 (power controlled by GPIO) - 1x microSD (GL857L) - 3x LED (all driven by GPIO) - 1x button (reset) - 1x 2-pos switch - header for optional PoE module - 1x micro USB for main power input - UART + I2C header on PCB Flash instruction: Vendor firmware is based on OpenWrt/LEDE. GUI or sysupgrade can be used to flash OpenWrt/LEDE firmware. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: image: move Sitecom WLR-8100 from legacy to genericPiotr Dymacz2018-01-153-9/+10
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: fix Sitecom WLR-8100 supportDavide Fioravanti2018-01-156-14/+17
| | | | | | | | | | | | | | This patch fixes Sitecom WLR-8100: - mtd layout - LAN and WAN MAC address setup - 2.4 GHz Wi-Fi MAC address setup - 5 GHz Wi-Fi support (calibration data, MAC address setup, missing ath10k-* packages) Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> [squashed commits, fixed whitespace issues, reworded commit message] Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network R36APiotr Dymacz2018-01-1512-1/+179
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network R36A is a successor of the previous model, the R36 (Ralink RT3050F based). New version is based on Qualcomm/Atheros QCA9531 v2. Specification: - 650/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R (QCA9531) 2.4 GHz, 2x u.fl connectors on PCB - 1x USB 2.0 (power controlled by GPIO) - 6x LED (5 of them are driven by GPIO) - 2x button (reset, wifi/wps) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - DC jack for main power input (12 V) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for Teltonika RUT900Piotr Dymacz2018-01-1513-0/+267
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Teltonika RUT900 is an industrial 3G router based on Atheros AR9344. There are available 3 other models in RUT9xx series: RUT905, RUT950 and RUT955, which differ in availability of additional I/O ports, built-in GSM modem type, GPS antenna and other features. FCC ID of the RUT950 model (LTE module built-in): 2AET4-RUT950. This patch adds support for the RUT900 model only but can be easily extended to cover whole series. Also, as there are several different 3/4G modules (Huawei, Quectel, Telit) used in whole series, packages required for WWAN support are not included by default. It is up to the user to install required software for built-in modem. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1 - 2T2R 2,4 GHz (AR9344), with ext. PA (MGA-22103) and LNA - built-in 3G module (example: Telit HE910-D) - 2x miniSIM slot - 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G) - PCA9539 16-bit GPIO I2C expander - 12x LED (4 are driven by AR9344, 7 by PCA9539) - 1x button (reset) - DC jack for main power input (9-30 V) - UART available on PCB edge connector Serial console pinout: - RX: pin1 (square) on top side of the main PCB (AR9344 is on top) - TX: pin1 (square) on bottom side Flash instruction: Vendor firmware is based on OpenWrt CC release. Use the "factory" image directly in GUI (make sure to uncheck "keep settings") or in U-Boot web based recovery. To avoid any problems, make sure to first update vendor firmware to latest version - "factory" image was successfully tested on device running "RUT9XX_R_00.03.960" firmware and U-Boot "3.0.1". Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network N5QPiotr Dymacz2018-01-1412-2/+172
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network N5Q is a successor of previous model, the N5 (outdoor CPE/AP, based on Atheros AR7240 + AR9280). New version is based on Atheros AR9344. Specification: - 550/400/200 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 2x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 2T2R 5 GHz (AR9344), with ext. PA (RFPA5542) and LNA, up to 27 dBm - 8x LED (7 are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - header for optional 802.3at/af PoE module - DC jack for main power input (optional, not installed by default) - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmare which is based on OpenWrt/LEDE. Alternatively, you can use web recovery mode in U-Boot: 1. Configure PC with static IP 192.168.1.2/24. 2. Connect PC with one of RJ45 ports, press the reset button, power up device, wait for first blink of all LEDs (indicates network setup), then keep button for 3 following blinks and release it. 3. Open 192.168.1.1 address in your browser and upload sysupgrade image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: add support for ALFA Network AP91-5GPiotr Dymacz2018-01-1413-0/+171
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP91-5G is a 5 GHz outdoor AP/CPE board, based on Atheros AR7240 + AR9280. Specification: - 400/400/200 MHz (CPU/DDR/AHB) - 32 MB of RAM (DDR1) - 8 MB of FLASH (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1T1R 5 GHz (AR9280), with ext. PA (SE5004L) and LNA, up to 27 dBm - 6x LED (5 are driven by GPIO) - 1x button (reset) - external h/w watchdog (EM6324QYSP5B, disabled and not used) - header for optional 802.3at/af PoE module - DC jack for main power input (optional, not installed by default) - UART and LEDs headers on PCB Flash instruction: Use "factory" image in vendor GUI (in case of problems, make sure your board has up to date firmware). Alternatively, TFTP in U-Boot can be used: select option "2. Load system code then write to Flash via TFTP" during early boot and use "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: cosmetic cleanups in preinit scriptsPiotr Dymacz2018-01-143-94/+83
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: drop LED control from 05_set_iface_mac_ar71xxPiotr Dymacz2018-01-141-1/+0
| | | | | | There is no "dir-615-c1:green:wancpu" LED defined in mach-dir-615-c1.c Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ar71xx: base-files: fix boards order in 05_set_preinit_iface_ar71xxPiotr Dymacz2018-01-141-3/+3
| | | | Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 13:28:37 +0000